Search Documents

By I. L. Nichols

The Bureau of Mines is investigating vanadium recovery from various domestic resources. A low-grade carnotite ore sample containing 0.34 pct V20S and 0.04 pct U30S was leached, and the results were compared with those of similar leach tests using a mill-grade sample containing 1.26 pct V205 and 0.19 pct U308. Experiments on the two ore samples included agitation leaching, pugging, salt-roast leaching, and autoclave leaching. None of the leaching methods investigated showed any significant advantage over another except autoclaving, which reduced the leach time but at the expense of greater acid consumption. Typical of the experimental results attained are the data gathered from the agitation leaching tests. Agitation leaching of the mill-grade ore with 100 lb/ton H2S04 resulted in extractions of 94 pct U308 and 33 pct V205. To increase the vanadium extraction from 33 to 91 pct required concentrations of 300 lb/ton H2S04 and 10 lb/ton NaC103. Complementary agitation leach tests on the low-grade ore required 200 lb/ton H2S04 to extract 94 pct U308, and 300 lb/ton H2S04 and 10 lb/ton NaC103 to extract 90 pct V205.

Jan 1, 1983

By Yasunori Kosaka, Junya Tokita, Aramaki Shosaku, Inoue Junji

Light ANFO that satisfies blasters and customers who want to reduce the amount of explosive consumption without changing blasting effects and designs and passes Cap sensitivity test regulated by law. The reduced loading density of light ANFO reduces the amount of explosive consumption. The loading density of conventional ANFO is 0.X-0.9g/ml, while the loading density of light ANFO is 0.7-OXgiml. The detonation velocity of light ANFO is maintained not to reduce blasting effects. Detonation velocity of conventional and light ANFO using steel tube of inside diameter 36 mm are 3200 - 37OOms. detonation velocities are the same though the loading density of light ANFO is reduced by O.lg/ml. This suggests that the reactivity of light ANFO improves.

Jan 1, 2002

The development of a noise attenuated compressed air driven fan is described. The fan, which employs the jet reaction principle, possesses blade extension pieces which penetrate into an acoustically treated annular chamber. The dominant noise source, namely the air jets, is thereby partially suppressed. In addition, the increased moment arm of the jets leads to an improved propulsion effect which contributes to the improved aerodynamic performance of the unit.A typical measure of the improvement of this type of auxiliary mine ventilation unit is a 4 per cent increase in efficiency and a 10 dB (A) drop in sound level for a fan duty of 0·5 kPa and 1600 litre/s. This degree ofattenuation corresponds to at least halving the loudness level, a subjective noise measure.

Jan 1, 1973

By Paul Meadows

This Bureau of Mines report presents operating practices and results of pressure maintenance and secondary recovery by water injection or by water injection supplemented by gas injection. Particular emphasis is placed on the results of water injection, which is the principal oil-recovery method employed in projects covered by this report. No attempt is made to study gas-injection projects or operations that are considered water-disposal projects. Also, this report does not include water-injection projects that have not been in operation long enough to evaluate results. Figure 1 is a map of north Louisiana showing the geographical locations of the projects included in this report. Most of the data used in this study were supplied by unit operators, operating companies, and the Louisiana Department of Conservation. Reservoir information and recovery data are generally those supplied by the operators, but include revisions where deemed necessary.

Jan 1, 1962

By A. R. Katti

The stone columns are widely used in the improving the bearing capacity of weak soils mostly for supporting flexible foundation systems. The load carrying capacity of a stone column is complex in nature. The load capacity is derived from the lateral stresses acting on the stone column due to load transmitted from the flexible structure due to deformation to soil mass and which in turn transmits lateral pressure in s3 direction. The load capacity is also function of the f value of the stone column, cohesion of the surrounding soil, K0 and Gb2 of surround­ing soil including passive resistance developed to lateral deformation of the stone column. The assessment of axial and radial deformation is much more complex. Recently Katti et.al. have developed a method based on a granular heap approach and computed with equivalent fe. which combines the effect of s3a and equivalent volume concept to estimate radial and axial strains. In this paper an attempt is made to put forward guidelines for design of stone column accounting for both stability with respect to shear and also with respect to settlement. The estimate of settlement are based on the internal properties of stone column and surrounding soil. It is considered thus the settlements computed are more realistic.

Jan 1, 1996

By Ronald Branstetter

Gaseous and particulate exhaust emissions from 20 diesel engines in service at five underground mines were measured with high accuracy instrumentation. The engines that were tested were checked for faults or maladjustments. The vehicle and engine maintenance organization was studied at each mine and an idealized maintenance program was devised. Faults were induced in a new diesel engine to determine their effect on the characteristics of the exhaust emissions. The results, conclusions and recommendations from this investigation are presented in this final report.

Jan 1, 1983

By D Rubery, C Croker

The Boddington Gold Mine (BGM) is located 120 km south east of Perth, Western Australia. The operation is managed by Worsley Alumina Pty Ltd and mined by contractor Henry Walker Eltin (HWE). The mine has been operating since 1987 with ore extracted from a series of pits along strike. Ore is contained within the basement rock, which is overlain by a cap rock layer and transition zone. Cap rock and basement zones require blasting.As the mine neared completion, a high-grade deposit was discovered within 50 m of an existing Western Power substation and 100 m from the processing mill. The substation provides power to the Boddington area and is a back-up power supply to the city of Perth. Due to the delicate nature of the transformers located at the power station, overhead power lines and the mill, blasting in the area was considered very high risk. As such blasting needed to be controlled for flyrock, airblast and most importantly peak vibration and frequency limits which had the potential to damage the transformers.The mine was due for closure in March 2001. The decision to mine the pit was based on its high grade, ability to be blended with lowering grades from other pits and changing of the processing technique with the expansion. This decision extended the life for a further six months.Due to the high potential risks a detailed risk assessment was conducted by Orica, Worsley and Henry Walker Eltin. The completed assessment and the major design parameters were presented to Western Power for approval. The ability to reduce the blasting risk was focused on limiting of vibration through controlling maximum charge initiated per delay, blast timing and firing direction, and other innovative control measures. OricaÆs SHOTPlan« and Sabrex« computer modelling packages were used to predict the outcome of blasts.The success of this project has opened the doors for other high risk blasting projects, which otherwise may be left unmined.

Jan 1, 2002

By Jamal Rostami, Levent Ozdemir, Amund Bruland, Filip Dahl

Cerchar Abrasivity Index (CAI) is one of the commonly used tests to evaluate rock abrasiveness for cutter life/cost estimations of TBM projects. There are at least 3 style machines, 2 different pin hardness, and the test could be run on fresh rock surface VS a sawn surface. Each of these parameters has a meaningful effect on the results, but its impacts were not fully understood nor its implications well explored. This paper reviews the current practice of Cerchar testing and its implications on geotechnical investigations related to TBM tunnels and provide a set of guidelines on testing and reporting of the test results for future projects.

Jan 1, 2005

Jan 1, 1998

By W. Duyvesteyn, B. Sabacky, T. Spitler, D. Verhulst

"The Altair TiO2 pigment process is based on hydrochloric acid leaching of ilmenite at high-acid concentration. Titanium is transferred by solvent extraction into a high-purity aqueous stream with a high titanium concentration. HCl gas is recovered by pressure-swing distillation and is used to regenerate the leaching solution.A new method of TiO2 recovery in dense film with simultaneous dehydration and hydrolysis provides great flexibility in adjusting the characteristics of the TiO2 pigment product.Modifications of this method lead to a flexible, low-cost, high-tonnage process first for the production of nano-sized TiO2, and later for stabilized zirconia-based nanomaterials and nano-sized titanates.IntroductionProcesses for the production of TiO2 from ore by a hydrochloric acid route have been proposed in the past. Most of these processes dissolve impurities and recover TiO2 as a residue or as a hydrolyzed phase in the original solution (Turner, 1948; Berkovich, 1975; Morris, 1982; Judd, 1986; Chao, 1993). Solvent extraction of titanium after leaching in aqueous HCl has also been studied (Tsuchida et al., 1982; Narita et al., 1983) or at least mentioned as an alternative (Ellis, 1963). A number of small-scale studies on leaching and solvent extraction in both sulphuric and hydrochloric systems have appeared recently (John et al., 1999; Lanyon et al., 1999; Sole et al., 1999. As far as we know, only Kerr-McGee (Morris, 1982) and a plant in India and one in Malaysia use a hydrochloric acid route (20 wt% HCl) to commercially produce synthetic rutile.The Altair process originated in a search for an economical method to treat high-magnesium ilmenite deposits, while avoiding the production of a waste metal salt by-product. The first attempts aimed at producing pure TiO2 by leaching out the impurities. Further work centred on completely dissolving the ilmenite in concentrated hydrochloric acid and reprecipitating TiO2. To decrease the impurity level in the product, solvent extraction of titanium into a purified stream was introduced. It also became clear that to take full advantage of the increase in leaching efficiency provided by concentrated acid, it was necessary to regenerate HCl gas."

Jan 1, 2002

The following pages discuss the objectives, the background, and scope of work of an industrial engineering analysis of far-,n haulage systems in underground retreat coal mining. This study ran concurrently with an existing industrial engineering study of methods of improving safety and production efficiency in underground pillar extraction. 1. OBJECTIVES The objective of this project was to provide basic data inputs that will inpart knowledge as to the major constraint to pillar extraction sections. Furthermore, the industrial engineering study will suggest ways to optimize haulage systems and to develop more efficient work practices and operational techniques that will maximize equipment utilization.

Jan 1, 1975

By Néstor D. Córdova

El presente trabajo revisa las técnicas empleadas y las condiciones previas para el sostenimiento y construcción del tunel Gandolini de la unidad minera Julcani. En esta perspectiva, el túnel sirvió de base para realizar las investigaciones de campo, obteniéndose así la información básica para un mejor entendimiento del comportamiento del macizo rocoso con miras a la solución de los problemas que planteaba su construcción. Por ello, la mecánica de rocas como técnica empleada, evalúa la alteración al equilibrio del macizo rocoso en el que se construye el túnel. Asimismo, se establecen criterios para la determinación de las cargas del techo y se los relaciona a los diferentes parámetros de diseño para llegar al cálculo del sostenimiento, dándose finalmente los aspectos prácticos relacionados a la selección de los tipos de sostenimiento más adecuados.

Oct 14, 1980

By J. Ran

There are challenges in mining deep tabular ore deposits using the open stoping method, particularly mining remnant panels towards the end of mine life. The remnant panels have experienced stress concentration and are in the failing or post failure state causing drilling and loading difficulties, ground movement, induced seismicity and ground instability problems. As more mines are going deep, without effective ground control management, the mine production will be interrupted and equipment damage and personnel injury are likely to occur. Mining at Falconbridge Lockerby Mine located in the Sudbury Basin was concentrated in the deep zone from late 1990s to 2004. The remnant panels situated approximately from 1800m to 1920m below surface were mined in 2004 before the mine closure. These panels were in the central section of the orebody along strike. The orebody was relatively narrow ranging from 5m to 15m and steep dipping at 70o to 80o. Because of the retreat mining sequence and the mining depth, stress concentration, wall closure and seismicity had caused a number of mining difficulties. Managing these challenges was critical in achieving the mine production target without compromising personnel safety and excavation stability. A comprehensive ground control management approach was adopted to mine the remnant panels at depth. The measures taken included ground movement monitoring, understanding the movement pattern of the footwall rock and selecting appropriate support systems, analyzing seismic monitoring data and defining re-entry protocol, brow support design and restricting access. This paper presents these ground control measures and the experience gained in successfully mining the deep remnant panels at Lockerby Mine.

Apr 1, 2005

By M. F. Bucek

This report summarizes the activities performed and the results achieved during a two-phased investigation of the technical and economic feasibility of disposing of coal mine refuse underground in active mines, Three coal regions in the United States that are most severely affected by coal refuse disposal problems are identified: southwestern Pennsylvania, southern West Virginia, southwestern West Virginia and eastern Kentucky. For each region, a conceptual mine model is presented that describes the geologic conditions, mining methods, and environmental circumstances typical of that region. The model mine that was prepared for the Kanawha Region in Southwestern West Virginia and eastern Kentucky was selected as the basis for developing alternative conceptual designs of underground disposal systems in the second phase of this investigation. Procedures used in selecting the regions and in modeling typical mines are described in Part I of the report. Part II of the report describes existing methods for stowing refuse underground, presents three alternative conceptual designs of stowing system that would be appropriate for the model mine postulated in the first phase of the study, discusses technical characteristics and environmental effects relative to the various systems, and evaluates the technical and economic feasibility of the three alternative disposal system designs. Comparisons costs among systems and with costs or surface disposal are presented.

Jan 1, 1980

Simulation and Analysis of Media Behaviour in the Tower Mill by Discrete Element Method for Estimating the Power Draw and Spatial Distribution of Grinding Process The trends to the Tower Mill (TM) for grinding the materials are increased recently due to its unique merits. Among the various considerations of this machine, the main important items are increasing the efficiency of grinding as more as possible while keep the power consumption, manufacturing and maintenance costs as less as possible. Because this grinding process includes a huge numbers of media particles (ball or other shapes) that are interacted with each other and body of the machine, the DEM (Discrete Element Method) way is a very useful and essential step to getting confident evaluations. Because the DEM simulation is a very young scientific field and proper commercial software are very rare and still under modification, at first step, a FORTRAN code is developed for DEM simulation of two laboratory Tower Mill models (KM5 and KD5). The simulation and experimental results matched each other properly. Then one another DEM software was implemented to perform simulation of bigger models (huge numbers of balls), meanwhile could handle the complex 3D geometry data. The simulation and experimental results were compared and analysed in detail for not only laboratory but also for industrial models (KW5, KWD5, KWD50, KW300F, KW700F and KW1500) without any manipulation or compromising of the parameters of simulation. Some numeric data of industrial models are hidden here due to confidential reasons. The relative velocity of balls (ball-ball and ball-TM body), dissipate energy, interacted forces and stresses during the process are the key outputs of DEM simulation for design this machine. Therefore the main important processes in a Tower Mill machine are recognised and consequently some horizons of development of this machine are distinguished.

Sep 13, 2010

By Leopoldo Mariscal

El presente trabajo describe los aspectos más importantes del proyecto de Fundición de Ilo como son: la tecnología, el desarrollo de la ingeniería y construcción, el impacto económico, social, tecnológico y ambiental de su ejecución y los planes de entrenamiento y comisionado de la nueva planta. Asimismo considera entre los equipos principales: un horno de fusión en baño ISASMELT asociado a un caldero de recuperación de calor y un precipitador electroestático, cuatro convertidores Peirce Smith, dos electroprecipitadores, dos plantas de ácido, dos plantas de oxigeno, dos plantas de efluentes, una planta de moldeo de ánodos, dos hornos de limpieza de escoria, y varias plantas auxiliares más.

Sep 12, 2005

By X Yang, B Wang, L Liu

"An EXTENDED ABSTRACT is available for download. A full-length paper was not prepared for this presentation. The Huoqiu iron ore field in north-west Anhui province is located in the south-east margin of the North China Craton and hosts large iron resources. Orebodies are hosted in Neoarchean amphibolite facies metamorphic rocks, forming silicon-iron bands from north to south. The area is dominated by an Early Precambrian basement consisting of Neoarchean grey gneisses, amphibolites and metasediments. The gneisses are similar with assemblages of Trondhjemite-Tonalite-Granodiorite in compositions and intercalated with amphibolites. Igneous zircons from gneisses and amphibolites have U-Pb ages of 2.86 and 2.75 Ga respectively, which are interpreted as the crystallisation ages of their protolith. Zircons from amphibolite and gneiss have eHf(t) values of 2.4–15.5 and -3.0–1.5 respectively. The tDM2(Hf) model ages of the gneiss range from 2.87 to 3.14 Ga, which is consistent with tDM1(Hf) ages of amphibolite (2.84–3.16 Ga). The U-Pb-Hf isotopes thus confirm that the gneisses were generated by partial melting of amphibolite. Two granites produce two group Hf isotopic compositions. The older one (1916 ± 42 Ma) has eHf(t) values and tDM1(Hf) ages of -9.4–3.4 and 2.24–2.71 Ga respectively, whereas the younger one (1823 ± 41 Ma) shows a large variation in eHf(t) values of -18.1–12.5 and tDM1(Hf) model ages of 1.73–2.92 Ga. Geological and geochemical characteristics indicate that the Huoqiu banded iron formations are a Superior-type iron formation rather than an Algoma-type as previously considered.CITATION:Yang, X, Liu, L and Wang, B, 2015. Study on the Huoqiu banded iron formation, West Anhui Province, East China , in Proceedings PACRIM 2015 Congress, pp 649–656 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Mar 18, 2015

By I. H. Van Horn

IN the development of the incandescent electric lamp one aim of the investigators has been to establish the fundamentals of lamp design, so that the performance of any new lamp may be accurately predicted. The study of the temperature relations in lamps has done much toward establishing these fundamentals. Fig. 1 gives the typical FIG. 1.-ARRANGEMENT OF PARTS IN MAZDA B AND MAZDA C LAMPS. arrangement of the lamp parts in both the Mazda B (vacuum) and Mazda C (gas-filled) lamps. The outstanding differences are the filament form and the bulb shape. The ideal lamp is one in which the filament operates at a uniform temperature throughout its length. In practice, it is necessary to disturb this uniformity by the introduction of supports and terminals. The amount of cooling at the supports and terminals affects the over-all efficiency of the filament as a light producer. The life of the lamp is ordinarily proportional to the maximum and not to the average filament temperature. The Holborn-Kurlbaum type of optical pyrometer has

Jan 9, 1919

By J. M. Toguri, K. Grjotheim

It is known 1,2 that the equilibrium between titanium metal, TiCl2 , and TiCl3, in a solvent of molten metal chlorides, is influenced both by the total amount of dissolved titanium and by the type of solvent. Assuming that the trivalent titanium forms the complex ion Ti111 Cl4, the equilibrium reaction may be expressed by the following equation, (Me) TiIII cl4+ 1/2 Ti = 3/2 TiII cl2+ (Me) Cl The ideal ionic equilibrium constant for this reaction is, Where the N's are the molar ionic fractions in the equilibrium melt, and (Me) the different types of cations present in the equilibrium mixture. The following thermodynamic relation is derived between Kand the concentration of cations in the equilibrium melt, mix The N"S are the equivalent ionic fractions, and so forth are constants corresponding to the standard changes in free energy for reactions in melts where only the cation indicated is present, and f (y1) is a function of the activity coefficients in the equilibrium mixture. When this term vanishes, a simplified linear relationship between In Kideal and the concentration is obtained. The simplified relationship has been applied with satisfactory results to the experimental data of Mellgren and pie,' and Kreye and Kellogg.2 MANY existing methods for the production of light metals involve the reduction of their respective metal halides in the presence of salt melts composed of alkali or alkaline earth chlorides. In such a solution phase, the light-metal halide may undergo stepwise reduction from a higher, to a lower valence, and finally to a zero valent state. In this connection, the disproportionation equilibrium is of great interest. In the case where the higher valence is three and the lower valence is two, the disproportionation equilibrium may be written as follows, 3 Me11 = 2 Me111 + Me [I] If this equilibrium occurs in a salt melt containing a large excess of alkali chlorides, a typical ionic melt is obtained. It is then possible to formulate the cation equilibrium: 2 Me+h' + Me = 3 Me++ [II] Reaction [11] is analogous to a cation exchange reaction. It has been shown thermodynamically that the equilibrium constant for such a reaction in 2

Jan 1, 1960

By Dae S. Young

A new probabilistic approach is introduced for slope stability analysis including adverse impact of blasting vibrations. The material strength within a slope area is randomized in this bi-variate joint probability analysis. To be a completely general engineering method, the new probabilistic approach employs the random variable transformation technique; the Hermite model of the Gaussian transformation function, which transforms the experimental histogram of strength values to the standard Gaussian variables. Because bi-normal joint probability is analyzed on the true probability region projected on the Gaussian transformed variable plane, it is an exact solution of slope stability based on the available sample data. Details of the probabilistic approach are given through a case study on an iron ore mine. The case study demonstrated that the probabilistic approach is effective and simple enough to be a routine engineering practice for slope analysis.

Jan 1, 1984