Search Documents

By John H. Johnson

This report covers research which is directed toward the measurement and control of underground mine diesel emissions. The report consists of three separate reports presented as Sections 1, 2, and 3. Section 1 "Emissions Measurement Apparatus" (EMA 1) discusses the selection and evaluation of instruments and procedures to be used as part of a diesel tailpipe emissions dilution and measurement apparatus. The instruments selected for gaseous pollutants are the Energetics Science Inc.* E.S.I.) 2000 for CO, the E.S.I. 7000 for NO and N02, and the Fuji ZFP5 for C02. Particulate matter is presently measured with the Celesco 1013 Smoke Opacity Meter. The raw exhaust concentration of one of these constituents is used Lo calculate the dilution ratio. Either a modified high range E.S.I. 2000 CO instrument or a Daco Products Cobra C02 instrument can be used, but neither is totally satisfactory. The study also indicated that it may he possible to increase the sample collection time from 15 seconds to the total 30 seconds over which the engine can be loaded without increasing the probability of damaging the vehicle hydraulic systems. Section 2 "The Effect of Fuels, Catalysts and a Filter Trap on Drift Pollutant Concentrations" discusses research in the Mine Air Quality Laboratory. A Wagner ST5D LHD with a Deutz F8L714 engine was used to compare three exhaust aftertreatment devices and a muffler-only system. The effect of these four systems on CO, C02, NO and N02 and on total, soluble, sulfate, and solid particulate matter was measured in the drift and on the LHD. The filter trap successfully reduced particulate matter for both fuels without significantly increasing the concentrations of any of the other constituents. The PTX catalyst was effective in reducing CO, and soluble particulate, but significantly increased N02 and solid and sulfate particulate matter. The Oxy Cat catalyst tested didn't seem to he working on the gases, and it significantly increased sulfate, soluble arid solid particulate concentrations. Section 3 "Diesel/Coal Particulate Matter Characterization by Laser Raman Spectroscopy" covers basic research on a method for determining the percentage by weight of diesel particulate on a filter containing a diesel-coal mixture. Signal-averaged Raman spectra provide the necessary precision. The method developed is non-destructive and uses as-received filters requiring no sample manipulation. Particulate with diesel contents in the range of 10 to 50% by weight have been analyzed with accuracies better than 6%t of the mean value. A number of samples containing diesel-coal mixtures were characterized by the procedures developed and the results are analyzed in light of various spectral and other system variables including coal rank and form and diesel engine operating conditions.

Jan 1, 1982

By Jackson R. Pressley, Bruce Vandenberg

An explosive’s velocity of detonation, (VOD), can be used to indicate a number of important characteristics regarding the product’s performance, under specific field and test conditions.

Jan 1, 1997

? CONSTRUCTION AND MINING COSTS ARE HIGH IN THE ARCTIC ? VERTICAL KIMBERLITE PIPES WITH HIGH STRIP RATIOS ? SITE SPECIFIC GEOMETRIC CONSTRAINTS ? OPEN PIT FOLLOWED BY UNDERGROUND MINING ? HIGH KIMBERLITE UNIT COSTS TRACK INSTALLED ON PIT WALL ? INTENDED TO REPLACE MAIN HAUL RAMP ? 5 MIN HOIST CYCLE TIME ? KEY ADVANTAGES - REDUCED CYCLE AND STRIPPING RATIO ? TECHNOLOGY EXISTS IN OTHER APPLICATIONS

May 1, 2003

By Edward J. McNamara

People in the real estate industry are fond of saying that the three most important features of a piece of property are, in order, location, location, and location. This is perhaps the reason that the owners of a well known high-end restaurant chain chose to spend $15 million dollars to renovate 5000 square feet of basement in a 22-story commercial building in the heart of New York City's Time Square. The goal was to create a music club with a stage area and dance floor with a mezzanine level surrounding the dance floor. In order to create the 50' x 40' dance floor and 20' x 40' stage area, 3 concrete columns were removed. New transfer girders were used to transfer the loads of these columns to new steel columns. For the mezzanine, nine columns had to be underpinned. All work continued while the restaurants, shops and offices above carried on business as usual. This paper details some of the means and methods utilized as well as the challenges faced by Underpinning & Foundation Constructors, Inc. in underpinning the columns and installing the new transfer steel.

Jan 1, 2000

The following Inventory was prepared to provide mineral deposit data to the U.S. Army Corps of Engineers for use in the Resource Development Navigation Study in Alaska. The inventory was prepared using data contained in the U.S. Bureau of Mines Minerals Availability System (MAS) database. The Alaska portion of the database contains Information on over 7,000 mineral locations and deposits throughout the state. When MAS was established In 1975, database entries were originally compiled from literature searches by both Bureau personnel and contractors. Deposit data are obtained/maintained through Information gained from a variety of sources, Including published and unpublished Bureau of Mines reports, records, and files; U.S. Geological Survey (USGS) Bulletins, Professional Papers, and other reports; technical and professional Journals; State and other Federal agency publications; data generated during field examinations; and information obtained from knowledgeable individuals. Because of the size of the data base, many of the data have not been significantly modified since initial entry. Each deposit on the MAS data base has a sequence number of the following form:

Jan 1, 2011

By J. L. Page, A. C. Marlowe

The Research and Development Services of South Africa has begun underground trials with a Robbins 52RE blindhole borer using a cutterhead fitted with high pressure water jets to assist mechanical cutting. The objectives of the work are to reduce cutter costs by increasing cutter life and to increase overall penetration rates. The paper reviews blindhole boring in South Africa and laboratory experiments in rock cutting assisted with high pressure water jets. The borer and its ancillary equipment are described. Initial results of underground boring experiments are presented. The paper concludes with the test programme for the future.

Jan 1, 1985

By Bernard J. Steblay

The U.S. Bureau of Mines has attempted to use ultrasonic signal travel-time measurements to measure loaded roof bolt strains. The strain measurements are then related to roof bolt loads through equations or empirical calibrations. Such techniques offer the potential of accurate, rapid bolt load measurement that does not disturb the anchotage. This report presents 6e research findings for a specific type of ultrasonic measurement instrument using a pulsed-phase-Iock-Ioop technique. This technique measures signal travel time indirectly by measuring frequency changes. A complete development of the applicable theory and detailed derivations of key equations is presented along with empirical laboratory and field results. The differences between anticipated and measured behaviors are analyzed and discussed. The report identifies problems encountered in applying pulsed-phase-Iock-Ioop technology to roof bolt load measurement and provides potential solutions to many of them. A key assumption of pulsed-phase-lock-loop theory is that driving and reflected signal frequencies will always be equal. Findings showed that not only were actual frequencies not equal but they were not stable or simply related. Reflection wave shape also was not stable. The ramification of these findings and ways to minimize their adverse effects are presented.

Jan 1, 1990

By Alfred H. Brand

New York City contains extensive deep deposits of glacial lake varved silt and clay, often overlain by organic soil. An 18 story building was proposed for Manhattan's upper East Side in one such area where bedrock is approximately 200 ft deep. Various pile and caisson alternatives were considered extending through the glacial lake soil to rock, but all proved beyond the project budget. Laboratory testing showed that the glacial lake deposits were preconsolidated. A test pile program using auger cast piles bearing in the glacial lake deposits proved that such piles could safely carry a load of 60 tons per unit. The auger cast pile scheme was estimated to be more economical than a deep pile alternative. A further benefit was that the vibration-free pile installation procedure posed less risk to adjacent structures which had been founded at shallow depth in fill above organic deposits and were stressed and cracked due to prior settlement. The project was designed with the anticipation that the glacial soils beneath the tips of the piles would produce a building settlement of 1 to 2 inches. The building was constructed in 2001 and 2002. It has been completed and is now occupied. Settlement data show that the building is performing as predicted. The auger cast pile scheme founded in a compressible stratum has proven to be successful and is a very unusual foundation alternative.

Jan 1, 2003

By A. Lashagri

This paper presents research results on assessment of environmental impact of digging and loading equipment in surface coal mining. Environmental impact is accessed through the equipment exhaust and dust emissions, and sound level. Exhaust emission is related to carbon dioxide (CO2), carbon monoxide (CO), nitrogen oxides (NOx), sulfur oxides (SOx), and volatile organic compounds (VOCs). Dust generation is expressed through the particulate matter PM10 and total suspended particulate matter (TSP), while sound is presented through the sound pressure level. Modeling of environmental impact of digging and loading equipment is conducted in Microsoft Visual Studio.NET software package. This research is a part of a boarder project on development of software system for the selection of productive, cost-efficient and eco-friendly mining systems, which is sponsored by the Appalachian Research Initiatives for Environmental Sciences (ARIES). The research work presented here may be used by mining professionals to aid in quantifying environmental impact of digging and loading equipment and determinate strategies for reducing its overall impact.

Feb 27, 2013

By Frank C. Townsend

Centrifugal model embankments with varying geometries and materials were constructed of- coal waste material, accelerated From 100 to 120 times earth's gravity, and subjected to various throughflow rates until failure occurred. Complementary laboratory tests were performed on the waste materials to obtain strength and permeability parameters for analytical calculations to predict observed centrifugal model behavior. Failures in the form of deep.-seated failure, or erosion and sediment transport or a combination of both, occurred in model embankments with 1V:1-1/2H and 1V:2H slopes when the phreatic surface due to seepage exited on the downstream slope: Positive seepage control, i.e., a toe drain successfully prevented sloughing and failures. Slope stability analyses agreed well, albeit conservatively, with observed model performance. Factors of safety ranged from 0.7 to 1.02 at the instant of failure for models with retrogressing slips as compared with 1.05 to 1.7 for stable embankments, These models verified existing criteria of a minimum safety factor of 1 3 and the necessity of positive seepage control.

Jan 1, 1980

By Sean Gallagher, Gene Wilson, Christopher Mark, Craig S. Compton, Gregory M. Molinda

Falls of small pieces of rock from between roof bolts continue to cause fatalities and to injure hundreds of coal miners each year. Roof screen is the most effective way to prevent these incidents, but some mines are reluctant to use it because they believe installing screen can be awkward, expensive and time-consuming. The most common type of roof bolting machine used in mines today is the dual boom, outside-controlled roof bolter. Mines who install roof screen using these machines have developed some machine modifications and techniques to ease roof screen installation. This paper describes some successful techniques and machine modifications that are being used in productive mines to assist with roof screen installation. Since the material handling involved with roof screen installation can expose miners to an increased risk of musculoskeletal injuries, the National Institute for Occupational Safety and Health (NIOSH) ergonomists, designed machine modifications and implemented a series of tests to evaluate roof screen handling procedures for outside-controlled, dual boom roof bolting machines. Roof screen installation can also have a positive economic impact on a mine by reducing the cost of injuries, workers’ compensation, required spot or re-bolting, and clean-up of long term travel and belt entries.

By M. C. Mound, E. Gallestey, C. Colbert

Continuous operating performance and high profit is one of the major concerns in the mining industry. Information systems are expected to reinforce and enable conformance to these requirements. The companion efforts of business management and production information systems press for tighter integration to avoid over-laps, multiple instances of similar data, and expensive maintenance of databases. Implementation of advanced intelligent systems throughout a mine operation can reduce costs, optimize investment and create a shorter payback via conversion of the data accumulated by field and process devices into information, and subsequently, into decisions. However, in order to harness the potential power inherent in these intelligent devices, adequate and flexible modular knowledge-based solutions are required. Fortunately, there has been at least one such practical response to this challenge, namely the ABB IndustrialIT portfolio. With these tools in place, production efficiency is reached via integration of process, production, and quality information. Moreover, they permit immediate detection and remedial action to changes to process and boundary condition variables. Finally, using advanced optimization techniques supported by dedicated mathematical models, they allow for economic process optimization (process set points and coordination thereof, energy management, production planning, energy supply contract optimization, etc) of the plant as a whole.

Jan 1, 2004

By Steven A. Hawkins

This report details the conduct and results of a 5-month study to collect data on the use of steel support for ground control in European underground coal mines. The report summarizes European steel support design practices and describes the applicability of steel supports to U.S. mining conditions.

Jan 1, 1980

By Lawrence J. Froisland

To aid in minimizing adverse environmental impacts of mining and mineral processing, the Bureau of Mines studied changes in soil characteristics in topsoil stockpiled during mining operations. Topsoil stockpiles in arid areas of New Mexico, Utah, and Wyoming were sampled over a 1- to 8-yr period to determine any changes in physical, chemical, or biological parameters in the top 15 ft of soil. Parameters examined in this study included soil moisture, pH, electrical conductivity, and cation exchange capacity; total nitrogen, organic carbon, carbon to nitrogen ratio, extractable potassium, and soluble phosphorus levels in the soil; general levels of bacteria activity in the soil; and productivity of the soil as measured by shoot yield in growth tests. Data were analyzed by multiple linear regression to determine possible effects of stockpile age and depth. Bacteria population counts, used as an indicator of goner l bacterial activity, was the only parameter found to be significantly correlated with stockpile age and depth at more than one site. Bacterial activity increased with depth at the two sites where it was measured. Activity increased with age at one site and decreased with age at the second. Significant changes in soil pH, electrical conductivity, and moisture were significantly correlated with stockpile age and depth at single sites. This study did not show significant, consistent deterioration in soil characteristics or growth yield of topsoil stored in stockpiles.

Jan 1, 1987

By Z S Chang, T F. Zhou, G X. Zhong

"An EXTENDED ABSTRACT is available for download. A full-length paper was not prepared for this presentation. The Yaojialing zinc-gold polymetallic deposit is a newly discovered, large skarn deposit in the Middle-Lower Yangtze metallogenic belt, East China. It is located in the transitional zone between the Tongling uplift block and the Fanchang faulted basin. It is mainly hosted in the contact zone between early Cretaceous granodiorite porphyry and Carboniferous-Triassic limestone, or occurs in limestone xenoliths within the intrusion. Skarn and stratabound massive sulfide orebodies are the primary ore styles. Sulfide ?34SV-CDT values indicate a magmatic sulfur source, in common with most deposits in the Tongling block. Calcite d13CV-PDB and d18OV-SMOW ratios reveal that marine carbonates were the major source of carbon in late-stage hydrothermal fluids. The calcite probably formed during interaction between magmatic fluids and carbonate wall rock.CITATION:Zhong, G X, Zhou, T F and Chang, Z S, 2015. Geology, chronology and isotope geochemistry of the Yaojialing zinc-gold deposit, Tongling ore district, Anhui Province, China, in Proceedings PACRIM 2015 Congress, pp 457–462 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Mar 18, 2015

By R. J. Charles

F. C. Bond: This is an outstanding paper on comminution theory and represents a considerable advance in mathematical formulation. It clears the way for a discussion that should ultimately decide whether the work index should be considered as a parameter according to the Third Theory or as a constant. In the empirical differential equation dE = —Cdx/x [1] either Corn must be treated as a variable to satisfy known crushing and grinding conditions. The author has chosen the exponent n as the variable, with C as a constant. According to the Third Theory, in the general case n is a constant equal to 3/2, and C is a variable related to the work index Wi. If x is placed equal to P (the size in microns which 80 pct of the product passes) and F is the size 80 pct of the feed passes, then C equals 5 W1, and dE = 5 -5 Widx/x = 10 Wi 10 Wi w = vP vF which is the basic equation of the Third Theory. It is apparent that this integration involves the error of treating the parameter Wi as a constant, just as the author's treatment involves the error of integrating his variable n as a constant. These errors are probably relatively unimportant, considering the small range of the variables. When more is known about the factors contained in the work index, Eq. 1 can be revised as a partial differential equation. The Third Theory exponent of 1/2, or n = 3/2 in the Charles' differential equation (Eq. l), was not chosen primarily because it is the average between the Kick and Rittinger exponents; this may be merely fortuitous, since it is illogical to define truth as the average between two errors. It was first discovered from the study of a large mass of crushing and grinding data and confirmed by laboratory testing. The general correspondence of the Third Theory equation to actual crushing and grinding results over the entire size reduction range argues strongly that a fundamental phenomenon is involved. The a posteriori theoretical explanation of the constant Third Theory exponent is that the work done in breaking rock is proportional to the length of the crack tips formed. Compressive force applied to the rock results in deformation and strain energy. When this locally exceeds the breaking strength a crack tip forms, the surrounding strain energy flows to the crack tip and extends it to split the rock, with release of the energy as heat. Under rapid impact the crack tip may form before the strain has reached equilibrium, resulting in less energy expenditure and probably a coarser product. In any case, the elastic limit of a brittle material is practically the same as its breaking strength, and the work necessary to form the crack tip is the work required to break. The crack length of a ton of broken rock cannot be measured directly. However, the particle shapes of feed and product are similar, and the crack length is considered equal to the square root of one half of the new surface area formed. It is, therefore, proportional to 1/vD, where D is the equivalent product particle diameter. This is the basis of the Third Theory equation. Many secondary factors can be imposed upon the crack length breakage. These may cause the Third Theory work index to increase or decrease somewhat as the product size becomes finer. The work index is properly a parameter rather than a constant, making it an increasingly valuable practical criterion of the work input required in crushing and grinding.

Jan 1, 1959

By M. Hopf, E. Rossouw

Keywords: Pyrometallurgy, furnace, copper coolers, freeze lining, monitoring, Saveway The use of water-cooled copper components as sidewall elements of submerged arc furnaces and other pyrometallurgical applications has become increasingly common. The high cooling efficiency of copper has made it possible to increase the service life of furnace refractories when compared to conventional refractory linings. However even the self-healing effect of ?freezing? worn areas of the lining does not necessarily protect the copper coolers against wear or corrosion completely. In order to avoid furnace explosions, various methods have been used to monitor the wear of coolers. Unfortunately, these have not been able to consistently identify localized wear. Thos Begbie (South African) and SAVEWAY (German) jointly developed technology to embed a line sensor into the copper cooler during the casting process. This system allows an exhaustive monitoring of the copper cooler. A SAVELINE sensor is placed inside the copper-cooling panel between the water-cooling passage and the hot face of the panel. The sensor follows the meandering shape of the cooling water channels. In the first instance, the sensor provides analogue information as the thickness of the copper reduces. Secondly, this wear signal will be confirmed by a signal of interruption if the sensor is washed away. Because of the structure of the sensor, a self-diagnosis is possible and indications can be confirmed (double proofed). Subsequent to the manufacture of some test pieces, coolers for a large submerged arc furnace were manufactured. The sensorized coolers have been installed at the intermittent surface (slag line) where the largest amount of corrosion has been encountered. The system has been operating since December 2005 in what is considered one of the largest submerged arc furnaces in South Africa.

Jan 1, 2006

By E. K. Stanek

This research study was performed on a case study basis and can be divided into two parallel thrusts: electrical and thermal energy conservation. Energy consumed annually in mining and refining operations represents about 6% of the 80 quadrillion Btu's consumed nationally. In the electrical portion of the study, five areas were addressed: optimal dispatching of on-site generation, high-efficiency motors, conductor selection, power factor correction, and high efficacy lighting. In the case study mine which has a multiple unit on-site generation system, optimally dispatching units can save significant energy. The other four methods are difficult to justify on a retrofit basis due to capital costs. In the thermal portion of the study, a thermodynamic analysis was performed on the reverberatory smelting process possible areas of energy conservation were identified as radiation and convection heat losses from the furnace arch and the dumping of high energy content smelting slag. It has been shown that materials currently available can provide the means of reducing heat loss from the reverberatory furnace. It has also been shown that a significant amount of energy may be recovered from the slag. However, these are both subject to further study and validation.

Jan 1, 1982

By James J. Snodgrass

The Bureau of Mines has investigated vibration levels produced by blasting at four underground sites to establish how such factors as type of explosive, delay blasting, charge weight, and geology affect amplitudes of ground motion. A summary of the work is presented and the results of further analysis of the data are discussed. Square root scaling was found applicable to two of the underground sites and could be applied with minor error to all the sites. Comparison of empirical propagation equations in the different rock types indicates that although the site effect is apparent, the combined data may be used as a basis for engineering estimates of vibration amplitudes from subsurface blasting in many different rock types. Recommendations for predicting and minimizing vibration amplitudes from underground blasts are given.

Jan 1, 1974

By Svend [Bue] Rondum

The final report contains a summary of the work performed under this contract, In addition to the report itself, other products were derived from this effort. Several hardware items were prototyped for use with underground belt conveyors, and a manual for installation and maintenance procedures was developed and published under separate cover. Recommendations have been included for implementation of the tools and the manual or, an industry-wide basis.

Jan 1, 1982