Search Documents

By Robert B. Johnson

The refraction seismic method has been used as an indirect means of exploring for fluorspar in southern Illinois by the Illinois State Geological Survey. Use of the method has been restricted to those areas where mineralization is associated with faults, a restriction necessitated by the operating principles of the refraction method. The seismic data enable the interpreter to locate fault zones in the subsurface and, under ideal circumstances, to make estimates of dip direction and magnitude and vertical displacement provided the local stratigraphic units are known and are geophysically recognizable. In this instance, refraction seismic exploration has been successful in the surface mapping of well-developed faults, both simple and complex with which fluorspar may or may not be associated. However, less clear results have been obtained where faulting has been less severe and where there are numerous accompanying mineralized joints.

Jan 1, 1964

By A. G. Kim

Methane and other hydrocarbon gases, byproducts of coalification, are emitted from coal at widely varying rates and often present ventilation problems during mining. The air in some coal mines apparently contains no methane. To determine if coals from mines which bid no history of detectable gas emission contained adsorbed methane, samples of coal at the shaft bottom and at an active face were obtained and placed in sealed metal cylinders. The atmosphere around the coal was sampled and analysed by gas chromatography. Methane, ethane, ethylene, propane, propylene, and butane were found to have been desorbed from these coals. Hydrogen and helium were also detected. An estimate of the amount of residual gas per ton A coal indicated that coal samples from the active face generally contained more adsorbed gas than coal samples obtained from the shaft bottom, although in both instances the total amount of gas was relatively small.

Jan 1, 1973

By R. D. Pehlke, J. V. Gluck

AS a portion of a general study of liquid-metal thermodynamics, high-temperature galvanic cells were used to study the effect of added dilute solutes on the activity of zinc in dilute solution with molten bismuth in the range 450° to 650°C. 1,2 The cells were of the type The experimental procedures have been described previously.1 In the course of studies conducted in the bismuth-rich corner of the systems Bi-Zn-Au and Bi-Zn-Cu, marked discontinuities were observed in the electromotive force-temperature relations for a number of the experimental compositions. Above the discontinuity temperatures, the relations, which were linear, exhibited slopes similar to the binary alloy of the same mole fraction zinc, as shown in Figs. I and 2. Below the discontinuity temperatures, the slopes were markedly different, but the relations remained linear. In general, as the amount of the third eletnent was increased, the slope of the lower portion of the relations tended to become less positive. The slopes of electromotive force-temperature relations reflect the entropy of mixing of zinc and, therefore, the occurrence of a discontinuity marks the transition between two different equilibrium situations involving the solution of zinc. A number of other investigators3-5 have used such observations to determine liquidus boundaries in binary alloys. Since the upper portions of the ternary electromotive force-temperature relations of this study had the same slopes as the binary alloys, the discontinuities are interpreted as marking the transition between the single-phase liquid region and the underlying two- and three-phase regions. Reference to the Zn-Bi equilibrium diagram6 confirms that the binary alloys were single-phase liquids at the experimental temperatures. Fig. I shows the electromotive force-temperature relations for the alloys containing Bi-Zn-Au and Fig. 2 shows similar relations for the Bi-Zn-Cu alloys. In the lower portion of each figure, the temperature of the discontinuity is plotted vs the mole fraction of the added solute at the various levels of zinc concentra- tion. Cross-plots from these curves at constant temperature permitted the construction of the partial liquidus surface isotherms shown in Figs. 3 and 4.

Jan 1, 1967

By W. Tom Witherspoon

Many Engineers are skeptical and cautious about skin friction factors for the portion of drilled piers where temporary casing is used. This has led Texas engineers in many cases to eliminate skin friction values for the cased section, which necessitates deepening the drilled shaft to compensate for the loss in the cased section. This paper has provided field test data that supports inclusion of skin friction in the temporarily cased hole section as a contributing factor in total axial capacity as comparable to open hole shafts of the same diameter. Reasons for the resultant friction values are provided including; remolding of the cased clay section and the increased pier circumference necessitated by the oversized casing required for adherence to the engineers shaft diameter specification.

Jan 1, 2009

By J K. Claflin, S R. La Brooy

A case study from a current Ausenco project is presented to demonstrate the importance of maintaining high carbon activity to illustrate the driving force for plant improvements such as a carbon regeneration kiln upgrade.This paper revisits the factors that influence carbon activity for gold loading, with emphasis on deactivation by organic solution components such as flotation reagents.Kiln process design requirements for effective thermal regeneration are reviewed including the interaction of parameters such as temperature, kiln atmosphere and residence time.The different types of kilns that have been used for carbon reactivation are described. A check list is provided of what to look for when purchasing a carbon reactivation system for dealing with severely fouled carbon. This covers the ancillary equipment as well as the kiln itself.While the effectiveness of the carbon reactivation kiln is vital to maintenance of high carbon activity it needs to be remembered that this is only the end of pipe solution. It is also important to ensure that reagents such as frothers and flotation collectors are appropriately chosen to maximise recovery and at the same time minimise carbon deactivation.CITATION:La Brooy, S R and Claflin, J K, 2013. Carbon management in a high gold price environment, in Proceedings MetPlant 2013 , pp 455-467 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 15, 2013

By D. E. Traut

A fluidized countercurrent ion-exchange system was developed, operated, and evaluated by the U.S. Department of the Interior, Bureau of Mines. The system consisted of integrated multiple-compartment absorption and elution columns in which the solution flows were continuous except for short periods when resin increments were withdrawn. The exchange of uranyl carbonate between a simulated in situ uranium leach liquor and a strong-base ion-exchange resin together with the subsequent elution with an ammonium chloride solution was studied. The effects of the number of sections, section height, amount of resin withdrawal, solution flow rate, and column diameter were investigated. The kinetic and equilibrium relationships for the absorption and elution steps were also examined. The experimental data indicate a strong interdependence between variables. Solution retention time appears to be a major limiting variable in the absorption process, while resin residence time is the determining factor in the elution process. The column was efficient over a range of conditions, but close control was needed for optimum operation.

Jan 1, 1978

By J. Allaire, P. N. Muteb

The Meadowbank mine is operated by Agnico-Eagle Mines Ltd. and is located in the Kivalliq District of Nunavut in northern Canada. The process plant operates presently at a throughput of 11,500 tpd with gold grade varying between 2.9 and 3.6 g/t. The ore supplied to the process plant come from two different open pits and it expected to come from a new open pit early 2014. The ore is mid-hard materials so the feed size ore have a bigger impact on the throughput. The average gold recovery is 94.0% with about 15-30% of gold recover from the gravity circuit. The Meadowbank mine commissioning started in February 2010 utilizing a flowsheet consisting of one stage of crushing followed by primary and secondary grinding. The commercial production began in March 2010. During the commissioning several difficulties were observed to reach the designed throughput of 8,500 tpd. It was evaluated to insert a second stage of crushing. The insertion of the secondary crushing have two objectives, first to reach easily the process plant design throughput as well as to evaluated the mill capacity increasing. The process plant team evaluated various expansion alternatives eventually deciding to install a secondary crusher, increased the SAG and Ball mills motors capacities and maintain the rest of the process unchanged. Early 2011, with the improvement in the gold markets, decision was made to install the secondary crusher between the primary crusher and the primary grinding. The process plant continued to operate on the initial design until early June 2011. This paper presents the SAG mill throughput increasing from the designed tonnage of 8,500 tpd to 2012 targeted tonnage of 11,500 tpd, secondary crusher commissioning and the difficulties to operate in Canada Artic (Nunavut).

Jan 1, 2013

By C. Ringas

Pipelines are used extensively in industry to convey various products. Internal corrosion of pipelines can lead to perforation and leakage of the product. A growing problem, not often accurately recognized, is internal corrosion of pipelines caused by bacteria. Microbiologically-induced corrosion (MIC) refers to corrosion caused by a variety of micro-organisms. This form of corrosion is not widely recognized in many industries, although it is widespread and causes many corrosion problems in pipelines, both internal and external. Sulphate-reducing bacteria (SRB) are responsible for the bulk of the corrosion problems caused by MIC. Corrosion caused by SRB is found extensively in water pipelines conveying raw, potable and waste water, as well as in pipelines conveying slurries. This problem also occurs in pipelines conveying crude oil. This paper describes internal corrosion problems of slurry pipelines caused by bacteria and outlines mitigation methods to improve slurry pipeline integrity, thereby extending the life of such pipeline

Jan 1, 2007

By Alla D. Mah

The heat of formation of scandium sesquioxide (Sc203) has not been measured previously, and existing values for gallium sesquioxide (Ga203) are subject to large uncertainties. As a consequence, thermodynamic calculations involving these oxides hare lacked scientific exactness. This paper reports newly determined values of the heats of formation of gallium and scandium sesquioxides at 298.15° K., by combustion calorimetry. The corresponding free energies of formation are derived from heat and entropy data.

Jan 1, 1962

By A. C. Fieldner, W. A. Selvig

For purposes of coal classification it is desirable to know the composition and calorific value of the pure coal substance; that is, of the coal free from its ash-forming minerals. Two methods suggest themselves: (1) To free the coal from most of the ash-forming material previous to the analysis; and (2) to analyze the coal as received and calculate the analysis, with certain more or less arbitrary corrections, to the pure-coal basis. Calculation methods are obviously more apt to give correct results with low-ash than high-ash coals. With coals of unusually high ash it would appear preferable to remove, previous to the analysis, as much of the inorganic matter as possible, by float-and-sink or acid-treating methods. Effect of Ignition on Inorganic Constituents of Coal The need of corrections in calculating analysis to the pure-coal basis is due to the fact that the ash, as determined by ignition, is not the same, in either weight or composition, as the inorganic mineral matter in the coal. On ignition a number of changes occur in the coal such as loss of water of hydration of the shaly material, conversion of pyrite (FeS2) to ferric oxide (Fe203) with evolution of the sulfur as sulfur dioxide or possible fixation of more or less of the sulfur in the ash as calcium sulfate (CaSO4), and decomposition of calcite (CaC03) to calcium oxide (CaO). The amount of sulfur from pyrite which remains in the ash as calcium sulfate depends on the amount of calcite and pyrite in the coal. Certain coals high in both calcite and pyrite show relatively large amounts of sulfate sulfur in the coal ash. The determination of total carbon and hydrogen in coal includes, besides the organic carbon and hydrogen, the carbon of inorganic carbonates such as calcite, and the hydrogen of the water of composition of some of the ash-forming minerals. For detailed discussion of corrections proposed for calculations of coal analyses to the " pure "

Jan 1, 1930

By Bernhard Leist, William D. Leech, Johann Kröyer, Holger Evers

Landsvirkjun—the national electric power company of Iceland—is building the Kárahnjúkar Hydroelectric Project in eastern Iceland. Two glacial river systems will be dammed and channeled through a series of tunnels into a 690 MW underground powerhouse. The Project has a total of 73 km of tunnels to be excavated of which mosthave been completed. From three access adits, three large diameter (7.2 m to 7.6 m),main-beam, gripper-type, Tunnel Boring Machines (TBMs) are being used to complete50-km of the waterway tunnel. Using the TBMs was a first in Iceland to excavate the complex Icelandic basalt formations, which consist of inclined layers of hard basaltic flows with weaker scoriaceous and sedimentary interbeds. Faults, fissures and dykes that frequently cross the lava flows posed both geologic and hydrogeologic difficulties to the TBM tunneling. This paper describes the extreme challenges that the men and equipment had to endure to complete the tunneling, including the harsh winter weather on the surface and the cold, abundant ground water inflows within the tunnels.

Jan 1, 2007

By W. H. Schiffbauer

NIOSH has developed an active proximity warning system called HASARD (Hazardous Area Signaling and Ranging Device) for warning workers as they approach known dangerous areas around heavy mining equipment and other dangerous work zones. HASARD is composed of a transmitter and a receiver. The transmitter generates a 60-kHz magnetic field using one or more wire loop antennas. Each antenna is adjusted to establish a magnetic field pattern for each hazardous area. The receiver, worn by the worker, is a magnetic field strength meter. The received signal is compared against preset levels which are calibrated to identify levels of danger. The receiver outputs can include visual, audible, and vibratory indicators and it can also be made to disable machine functions. HASARD was field tested on a Joy 12 continuous miner, a Komatsu 210 M Haulpak, and on a highwall launch vehicle. Slight modifications were made for each application. HASARD provided warnings as designed and proved to be rugged enough to withstand the harshest of production environments.

By Henry C. Meeves

The Bureau of Mines, between 1956 and 1963, examined 18 major pegmatite districts in Arizona, Colorado, New Mexico, South Dakota, Utah, and Wyoming to evaluate their content of beryllium, a material in short domestic supply that has become increasingly important to modern industry. This examination report includes the salient statistics on the production of pegmatite minerals other than quartz and feldspar; and brief descriptions of 170 specific pegmatite deposits.

Jan 1, 1966

By Lawrence Williamson, Randall J. Essex, David P. Field

As part of a $2.2 Billion bridge project that will link Indiana and Kentucky, an interchange project northeast of Louisville will require the mining of a 6-lane tunnel system about 2,000 ft long in order to cross beneath the historic Drumanard Estate. This paper will discuss preliminary engineering that has been undertaken to compare two-bore and three-bore layouts, the planning of an exploratory tunnel facility, and the potential for including a test chamber to investigate the ability of high capacity roadheaders to mine the 22,000 psi limestones.

Jan 1, 2005

By C. O. Karacan

Underground longwall mining of coal causes large scale disturbance of the surrounding rock mass. The disturbance can increase the rock mass permeability through a reduction on the stress as well as formation of new fractures in the rock. Methane gas contained in the disturbed rock mass can migrate towards the low pressure mine workings and present an explosion hazard. This paper describes the application of a finite difference program to develop a geomechanical model that predicts permeability changes within the rock mass. The calculated permeabilities are used as input to a reservoir simulator that models methane desorption from the coal matrix, methane release from the rock layers and flow towards the mine excavations. The model also considers the basic characteristics of the mine ventilation network. The geomechanical model uses empirical relationships between fracture permeability and stress to calculate permeability changes around a longwall face. The extent of rock failure is determined using a strain softening model that considers both rock matrix and bedding plane failure. The cave rock (gob) is modeled as a compressible, granulated material. The calculated horizontal and vertical permeabilities around the longwall face are averaged and used as one of the inputs to the reservoir model. The reservoir model was developed and calibrated against records of methane flow at a study mine in southwestern Pennsylvania. Good correlation between actual gas production and model outputs has been achieved. The modeling approach provides a basis for estimating methane inflow and optimizing control measures.

By Olaf Andersen

Crucible melt extraction yields short metal fibers with eqivalent diameters as low as 50 µm from almost arbitrary metals and alloys. Highly porous components can be made from such fibers by suitable deposition and sintering methods. This technology is being developed at the Dresden based Department of Powder Metallurgy and Composite Materials of the Fraunhofer Institute for Manufacturing and Advanced Materials (IFAM) and has been applied to gold alloys and iron-base alloys containing small additions of precious metals. From the manufactured gold fibers, sintered structures were made for decorative applications. Additionally, it was found that due to rapid solidification during the fiber formation, precious metals can be finely dispersed in ironchromium- aluminum (FeCrAl) and FeAl20 alloys. Good catalytic activity at elevated temperatures was found in compositions containing 3 wt.-% Ce and 0.5 wt.-% Pt.

Oct 1, 2003

By Laurance L. Oden

The Bureau of Mines is developing melting data for binary combinations of the alkaline earth fluorides and yttria to facilitate the formulation of slag composition. Liquidus and solidus temperatures and solid solubilities were determined for the BaF2-Y203 system, and the information is presented as the phase diagram. The phase diagram was constructed from data obtained by ceramography, X-ray diffraction, and thermal analysis of specimens encapsulated in small molybdenum ampoules. The data indicate a simple eutectic system with maximum terminal solid solubilities of less than 1 mole pct. The eutectic temperature is 1,343° C, and the composition of the eutectic is less than 1 mole pct Y203.

Jan 1, 1970

By E. J. (Kirk) Conway

The objectives of this project were to: (1) determine the extent to which maintainability design concepts and principles have been applied to the design of underground coal mining equipment, (2) try to assess its impact on productivity and personnel safety, and (3) develop maintainability guidelines to enhance the design of new or rebuilt equipment. An equipment design review was completed at ten operational coal mines. The purpose was to identify design approaches and features that enhanced and degraded the maintenance process. Mine management, safety, and maintenance personnel were also interviewed to identify machine specific design problems. Six original equipment manufacturers were visited and the procedures used to enhance the maintainability of Their equipment discussed. Volume I of the Final Technical Report presents an overview of procedures and protocol used and a summary of the findings. Volume II includes the maintainability design guide for mobile underground mining equipment.

Jan 1, 1988

By G. W. Jones

During the course of an investigation by the Bureau of Mines into the causes, behavior, and control of anthracite-mine fires, it was observed that the carbon monoxide disappeared from a sealed fire area much more rapidly than could be explained on the basis of leakage of gases. Two suggestions were offered for this high rate of disappearance: (1) That the carbon monoxide, was oxidized at temperatures below 150° C. by either the anthracite or its ash (tests on many anthracites have shown that at temperatures above 150° C. carbon monoxide is liberated in the oxidation products when air is passed through it); (2) that the carbon monoxide was oxidized by micro-organisms present in the sealed area.

Jan 1, 1939

By Ali Ameli

Design loads are limited for piles relying upon toe stresses in rock due to uncertainty about the rock quality over the whole pile diameter because of rock mass properties or construction effects. The paper discusses the use of video images to evaluate rock quality at the bottom of piles socketed into graniodorite bedrock in a steel pipe pile project. Skillful interpretation was required to assess the 3D properties of the rock from video images. It is necessary to observe the rock mass characteristics near the project site for better perception of the rock features from the images. Video image interpretation skills were established by the evaluation of the cores drilled under the socket base and the results of pile loading tests. Correlations were found between rock appearance in the images and the rock socket drilling records. Rock socket acceptance criteria were developed through monitoring the drilling operations for the specific site procedures. Video images then served as one of the quality-assurance tools together with probing and pile loading test. Lessons and methods learned from video inspection in this project could be used to evaluate rock quality in similar cases.

Jan 1, 2006