Search Documents

By S. J. Jung

A fundamental study of fragment size distribution and characteristics of fracture pattern is presented for the dynamic penetration of a conical bit into coal block. In this paper, damaged zones during crater formation and fragment size distribution were studied. Bit with a sharper tip angle and a smooth body configuration performed better penetration. Results suggest that in coal cutting the trend should be toward the face cleat direction using a sharper angled tip bits which consumes less energy for an optimum range of penetration depths, thus attaining maximum cutting efficiency and reducing fine fragments.

Jan 1, 1989

By L. A. Neumeier

The Bureau of Mines investigated hot-rolling and forging characteristics of experimental ductile iron castings, both sand and permanent-mold, made with charges containing up to 70 pct foundry pig iron and 95 pct steelmaking pig iron. Between 1,550° and 1,950° F, most castings could be rolled to 90-pct reduction or forged to 70-pct reduction without serious cracking. Charge and composition have less bearing on workability than on subsequent properties. Permanent mold castings could be worked as readily as sand castings at 1,750° and 1,950° F. Plasticity improved with temperature. Small billets were also forged cold to 50-pct reduction without cracking. With equivalent nodularity, composition affects properties of wrought materials by altering matrix structure and strength. Properties vary with reduction and improve with increasing working temperature. Rolled material has high strength and anisotropy, and low ductility, particularly in the trans-verse direction. Annealing reduces strength and improves ductility, but anisotropy persists. At 70-pct reduction, impact resistance in the longitudinal direction is about twice that in the transverse. Annealing roughly doubles impact resistance. Deformation enhances damping capacity. The feasibility of die-forging and bar-rolling of ductile iron was evaluated in trial tests conducted under a Bureau contract. Although workability and ductility of ductile iron are inferior to those of steel, more advantage could be taken of ductile iron's plasticity to work rough shapes to final dimensions.

Jan 1, 1980

By J. A. Finch, Zhenghe Xu

The competitive adsorption of xanthates on sulphide minerals in a binary mineral system (pentlandite and pyrrhotite) was studied using the pseudo-in-situ technique of attenuated total-reflectance FTIR spectroscopy. The minerals were placed in the same collector solutions, either separated by a glass wall or in direct contact with each other before magnetic separation and separate analysis. The effect of mineral interaction on xanthate adsorption was clearly demonstrated spectroscopically for the first time. At low concentrations of xanthate, its adsorption on pentlandite was activated by physical contact with pyrrhotite; the effect may be attributed to the enhancement of electron transfer through electrical contact between the two minerals. The results emphasise the need for caution in extrapolating results obtained from single-mineral studies to flotation practice

Jun 18, 1905

By Kray Luxbacher

Three-dimensional time-lapse velocity tomograms were generated to image stress redistribution around a longwall panel to produce a better understanding of the mechanisms that lead to ground failure. Mining-induced microseismic events provided passive sources for the three-dimensional velocity tomography. Surface-mounted geophones monitored microseismic activity for 18 days. Most similar studies have utilized active sources including longwall shearers, controlled explosions, and hammer blows. These active sources generally require a person to initiate and measure the location and time of the source, and are not conducive to continuous monitoring. This method utilizes mining induced microseismic events as passive sources and lends itself well to continuous monitoring. Two event location methods were compared in order to move toward quantification of tomographic results in terms of ground conditions. Additionally, LAMODEL was utilized to determine the expected stress distribution around the longwall panel and compare these images to the velocity tomograms. Eighteen tomograms were generated, one per day, and high velocity regions in the set of tomograms generated from the initial location algorithm correlated with abutment stress redistribution predicted by numerical modeling. This research is significant as it has the potential to improve safety in underground mines and is the only example of long term passive velocity tomography implementation for the purpose of inferring stress redistribution around an area of active mining. Though still immature, this technology has the potential to allow mine personnel to image areas of active mining on a regular basis and detect areas with anomalous velocity distributions indicating potential safety hazards.

Jan 1, 2007

By W Polkowski, M Tangstad, M Wallin, J Jiao

Fe-26Si-9B (wt per cent) alloy has been identified as a potential high-temperature phase change material (PCM) due to its attractive properties, such as its high latent heat of fusion and low volumetric change during solid/liquid transition. For the successful utilisation of this alloy into thermal energy storage (TES) systems, the development of a cost-effective production method is essential. Presently, the Fe-26Si-9B alloy is produced by mixing FeSi alloys with either pure boron element or FeB alloys. However, the use of pure boron is financially prohibitive, and the carbothermic reduction results in high greenhouse gas emissions and high energy consumption in the production of FeB alloys. In this regard, our study proposes a silicothermic reduction method to produce Fe-26Si-9B PCM by using FeSi alloys and B2O3-based oxides. Accordingly, the influence of various parameters on the production process was investigated, including operating temperature, holding time, B2O3 content in the added oxides, and initial Slag/Metal (S/M) ratio. Based on the experimental results, the optimal parameters for producing FeSiB alloys with over 9 wt per cent boron were determined. Consequently, it was documented that the FeSi alloys and the added oxides enriched with 50– 65 wt per cent B2O3 should be subjected to temperatures ranging from 1550–1650°C, maintain an initial S/M ratio exceeding 1, and ensure a holding duration beyond 1 hr. Moreover, the energy consumption of this process was estimated to be ~1.86 MWh/t metal and the mass loss was lower than 7 per cent. Therefore, silicothermic reduction offers a sustainable approach for producing FeSiB alloys with a boron content above 9 wt per cent.

Jun 19, 2024

By J. L. van Niekerk

The research project reported on represents the first comprehensive attempt to measure the vibration levels of a variety of tools and equipment in the South African mining industry to determine the effect thereof on the health of workers and operators. Although human vibration has been studied extensively internationally only one reference pertaining to the South African mining industry could be found. From studies conducted in Canada and elsewhere it was evident that rock drills do have potentially hazardous levels of vibration. The scope of the research included measurements on a broad spectrum of tools, machines and vehicles used in the South African mining industry. Both hand-arm vibration, where the majority of the vibration enter the body through the hands, and whole body vibration, where the whole body is exposed to vibration through contact by the buttocks or feet, were investigated and measured. More than 700 sets of vibration data measured on 70 machines at 15 mines and workshops were obtained. Data were obtained for at least 24 different types of equipment and machines that were previously judged to have medium to high levels of vibration. All measurements were conducted in accordance with the international standards: ISO 5349, on hand-arm vibration, and ISO 2631-1, for whole body vibration. The equipment with the highest vibration levels in the hand-arm category was: rock drills, both pneumatic and hydraulic; pavement breakers and jackhammers; hand-held compactors; pneumatic wrenches and electrical hammer drills. Of these the rock drills had weighted vibration levels in excess of 20 m/s2. As far as whole body vibration was concerned the highest values were measured on earth-moving equipment. The major conclusion from this study is that the measured vibration levels are sufficiently high to create an enhanced level of risk of vibration-induced disorders in a significant proportion of the operators of hand-held equipment. The most notable examples are hand-held rock drills, pavement breakers, jackhammers and certain selected workshop tools. The results of the study indicate that a comprehensive epidemiological study should be undertaken on present and past workers to determine the prevalence of vibration-induced disorders.

Jan 1, 2000

Significant advances have been made in the design of centrifugal slurry pumps that are used for pumping high-density viscous and paste slurries. This paper presents the results of a series of centrifugal pump performance tests that were conducted using an FLSmidth 6 x 4 Krebs millMAX centrifugal pump. The pump was fitted with a dry mechanical seal to prevent dilution of the slurry from gland service water, as the theology of the slurry is sensitive to small changes in slurry density. Tests were done using paste kaolin slurry with Bingham yield stress values between 578-1 120 Pa and plastic viscosities between 728 and 1491 mPa.s. The viscous properties of the paste during each pump test were measured using a rotational viscometer. Pump head and efficiency de-rating were measured and compared to the correlations of Walker and Goulas (1984). The test data shows the pump's best-efficiency point (BEP) changes and shifts to the left of the performance curve. The pump efficiency decreases as the slurry yield stress increases. The head de-rating data shows more head de-rating at the low flow rates compared to the high flow rates for the high viscosity slurry, which is in line with the findings of Walker and Goulas (1984). This paper demonstrates that it is possible to pump very viscous, high yield stress slurries with limited head and efficiency de-rating using centrifugal pumps, provided that positive suction conditions are maintained at all times.

Jan 1, 2012

South Africa?s primary electricity supplier, Eskom, provides incentives to reduce power demand during critical times by granting capital through a Demand Side Management programme. DSM encourages the end user to review and optimize energy consuming systems and use capital, provided by Eskom, to purchase or modify the equipment required to achieve a load-shift. As part of the DSM agreement the mine ultimately acquires the capital equipment and benefits from reduced power costs, but in return is required to sustain the load-shift tactic for up to five years. The paper focuses on one DSM tactic, main fan energy management. In this case, reduced air flows during selected peak and off peak periods, results in a substantial reduction in peak power demand. DSM incentives provided capital for automated main fan control as well as improved control of the mine ventilation systems. To examine the work in detail Gold Fields Ltd Driefontein gold mine near Johannesburg was chosen as a case study.

Jan 1, 2009

By V. I. Lakshmanan, D. A. Mackie

"1. INTRODUCTIONIn the past two decades, low-grade gold and silver ore bodies in the United States have been exploited by heap leaching, primarily with sodium cyanide solutions. This method has proven to be a viable alternative to conventional milling due to its low capital and operating costs. Successes have been made, particularly in Nevada, where ores are well oxidized and the climate is conducive to this method. in recent years, heap leaching has been tried in northern latitudes with some success, however, in using this method, operators face more severe limitations than do their neighbours to the south.This paper evaluates the limitations of heap leaching with particular emphasis on northern climates and introduces an alternative method to recover precious metal values in a continuous vat. This proprietory technology, known as the Mackie Vat Leaching Jig, shows promise, with improved gold recovery and potential to operate in cold climates.2. WHAT ARE THE LIMITATIONS TO HEAP LEACHING?Heap leaching of non-refractory ores is subject to the following limitations:1. Minimum amount of free gold and nuggets in the ore.?. Minerology of the ore--accessibility of gold to lixiviant.3. Minimum particle size and size distribution of crushed product to allow percolation of lixiviant through the heap.4. Minimum amount of clays or clay-like slimes that can cause coating of ore particles and channelling of lixiviant.5. Minimum strength of ore particles or agglomerations to allow economic height of heaps to be built.6. Amount and suitability of real estate.7. Amount and type of precipitation.8. Ambient temperatures.9. Possible poorer lixiviant diffusion.10. Possible lower oxygen content in dissolved cyanide solution with higher heaps, particularly with ice and snow cover."

Jan 1, 1989

By Steve Kral

When the price of gold cracked the US$9.60/g(US$300/oz) mark last year, the gold-mining industry began to crank up again. This followed several years of gold prices that had languished in the mid-200s. Existing mines increased production and mines that had lain dormant for many years were getting second looks. The United States still produces a large amount of gold. But not much of the new production is coming from that country. Instead, strict environmental regulations still have companies wary of trying to invest the millions needed to start a new mine or expand existing ones. And after years of studies and negotiations between legislators, environmental interests and the mining industry, the United States still has not crafted a new mining law.

Jan 1, 2003

By E. R. Cole

Laboratory heats of an 80 percent copper high-leaded tin-bronze alloy, similar to Brass and Bronze Ingot Institute (BBII) alloy 3A, were made with reduced tin content to determine whether an alloy comparable to BBII alloy 3A could be produced using less tin to aid in conserving this strategic metal. The tin content was lowered from 10 percent to 8 percent and 5 percent (nominal values), respectively, and the reduction in tin was offset by either increasing the lead content or adding zinc. Mechanical properties, machinability, and corrosion characteristics of the resultant alloys were investigated, and the mechanical properties were compared with BBII typical values and American Society for Testing Materials (ASTM) minimums for high-leaded tin-bronze alloy. Results indicate that the tin content of this alloy could be reduced approximately 1 percent (difference between the 8.4 percent actual tin composition obtained and the 9.3 percent BBII minimum) without seriously affecting the desired properties. Results also show the tin content could be reduced without significantly increasing the chances of rejects for mechanical property failures, which might result from normal variations in the casting process.

Jan 1, 1972

By H. Copur

Experimental studies for quantification of force and brittleness indices relevant to rock cutting performance are presented. A simple interpretation method is developed, which quantifies the force-penetration response obtained from indentation tests. Basic parameters of the quantification are force increment and decrementrates, force increment and decrement periods, and number of increment and decrement data points. Blocks of eleven different rock samples were collected from different operating mines in Turkey and subjected to indentation tests to calculate the indices. The samples included harzburgite, serpentinite, trona, limestone, claystone, two different sandstone samples, siltstone and three different chromite ore samples. The concept was validated by a set of full-scale linear cutting tests using a conical cutter for measuring the cutting performance in relieved and unrelieved conditions, i.e. cutter forces, specific energy, size distribution of rock cuttings. The rock cuttings were sieved to determine coarseness index, indicates coarse chip generation characteristics, and size distribution. The force index is moderately correlated with the cutting performance and mechanical properties of the rocks, and poorly correlated with the coarseness index and size distribution of cuttings. A general and moderate trend is observed between the brittleness index and the coarseness index, cutting performance for unrelieved cutting conditions and mechanical properties of the rocks. However, additional data is required to fill the data gaps and to potentially establish relationship between the brittleness index and all other parameters.

Jan 1, 2003

Two coal seams were selected and the conceptual designs were based on the geological and physical conditions typical of these seams. As a result of the screening process presented below, the two coal seams selected were the Lower Kittanning Seam in central Cambria County, Pennsylvania and the Pittsburgh Seam in northwestern West Virginia and southwestern Pennsylvania. SELECTION PROCESS FIRST SCREENING OF LONGWALL OPERATIONS The list of longwall operations prepared in Phase I and included in the Phase I report, was used as the basis for a first screening. From this list it was determined which longwall operations were not in the Appalachian coal fields and not in a coal seam of the thickness range of 42 to 72 inches. The first screening eliminated 30 of the listed operations, leaving 48.

Jan 1, 1976

By Matthew J. Sheridan

The Bureau of Mines study described in this report was conducted in the Denver, Colo., area (1) to summarize existing conservation practices as related to the most beneficial utilization of deposits of sand and gravel; (2) to identify the conflicting positions of the aggregate producer, the mineral owner, nearby residents, and local government officials responsible for determining land status and for issuing operating permits; and (3) to show the need for planning in Denver and in other expanding communities toward obtaining the benefits of conservation of our rapidly dwindling mineral resources. In order to determine the effects of urbanization on the Denver aggregate industry, interviews were held with owners of sand and gravel operations, with producers of concrete and bituminous pavement, with city and county planning and zoning personnel, and with representatives of various interested organizations. The conservation and ultimate utilization of deposits of construction raw materials near expanding urban areas can best be accomplished by long-range land-use projection and the requesite cooperation of technically advised planning and zoning administrators, government officials, mineral producers, and land developers.

Jan 1, 1967

Two concentrates from Palabora, in South Africa, containing 0.056-0.068% undesirable Cu and 0.8 or 2.2% Ti, were chlorinated with air:chlorine ratios of 10:1, 15:1 and 20:1 at temperatures between 1 200 and 1 329 K. The resulting volatile chlorides were condensed and the solutions analysed for Cu, Fe and Ti. Recovery of Cu was less than 25% at low temperatures and short reaction times, but at 1 258 K almost all Cu was removed from the magnetite at all ratios of chlorine to air. At higher temperatures, the increased carrying over of iron as FeCl3 could be minimised by decreasing the partial pressure of chlorine. No titanium was detected in the volatile products and the percentage of Cu recovered was independent of Ti concentration in the concentrates, though as a function of Cl2 vol%, more Cu was recovered at 1 200 K from the low-Ti than from the high-Ti concentrate. In a fluidised-bed reactor, Cu recovery was 58-90% and iron carry-over less than 10 ppm

Jun 21, 1905

By Frederic Vanderoost

Actualmente, el manejo adecuado de las informaciones geológicas en el sector minero optimiza recursos y maximiza resultados. En ese sentido, el presente texto señala la implantación de un conjunto de herramientas para la administración de banco de datos geológicos, de forma corporativa y manteniendo un informe central de datos. Dichas herramientas se basan en sistemas comerciales de base de datos como Oracle, Microsoft SQL Server y Sybase, los cuales garantizan agilidad, flexibilidad y capacidad de almacenamiento para el manejo de informaciones adecuadas y las operaciones típicas de la industria minera. Asimismo, se presenta estudios de casos, analizando sus ventajas, limitaciones y dificultades encontradas en una mina.

Aug 25, 2002

By D Kotzen

Online cyanide analysers have been successfully used to control free cyanide in the gold/silver leach process for over 15 years. Use of such analysers leads to cyanide savings and improvement in recoveries. Plants with leach cyanide analysers show both lower and more consistent cyanide levels in tailings. Cyanide code compliance requires meeting residual cyanide targets in tailings. Monitoring and logging of the residual cyanide in plant tailings and effluent is required. Meeting targets may require cyanide recovery/destruction processes to be implemented. The operating cost of destroying cyanide is often the same order of magnitude as the cyanidation cost. Various cyanide destruction and/or recovery processes are reviewed. Choice of a process consistent with the environmental and operational requirements is illustrated. Online weak acid dissociable cyanide (CNWAD) analysers have recently been developed and introduced on gold plants. The application of a WAD 1000 online CNWAD analyser at a large gold plant is presented. The analyser ensures code compliance, reduces cyanide destruction process operating costs and forms a historical record of CNWAD values in tailings.

Jan 1, 2007

By S Colak, M Tunc, C Celik, M. M. Kocakerim

The most important parameters affecting the solubility of ulexite (sodium calcium borate) in H2SO4 were found to be reaction temperature and solid:liquid ratio, in that order. Dissolution increased with increase in temperature and stirring speed and with decrease in solid:liquid ratio, particle size and acid concentration, the last effect as a result of decreased precipitation of CaSO4 on unreacted particles. Optimum conditions, in which around 99.5% of the ulexite could be dissolved, were a reaction temperature of 60 degrees C, a solid:liquid ratio of 1:8 g/ml, an acid concentration of 8 mol/l, particle size smaller than 425 micrometres, a stirring speed of 52.33/s, a reaction time of 1 800 s, a calcining time of 3 600 s and a calcining temperature of 170 degrees C. These conditions, determined by the Taguchi method, are reproducible in a commercial production environment

Jun 21, 1905

There are multiple stages in a mining operation that a mining engineer has to draw polygons to be used as operation guidelines. These polygons are drawn by hand and based on engineer?s experience. However, having automatic procedures for forming the shapes can increase the quality and decrease the efforts required. These shapes need to be homogenous in grades and rock types so that the quality and dilution of material sent to the plant can be estimated with the good approximation. In this paper, a clustering algorithm with shape control is introduced which can provide reasonable guidelines for all the aforementioned shapes by manipulating its parameters. At the end, implementations of the algorithm on a small part of a gold deposit with different mining strategies is presented and evaluated based on homogeneity of grade, rock types and determined destinations as well as the shape.

Feb 27, 2013

By F. G. Horino

This report presents the theory and design of a stiff loading machine used by the Bureau of Mines. The machine incorporates three high-strength steel columns as the restraining member in parallel with the specimen. The theory presented gives the basis of design and the dimensions of component parts of the machine. Laboratory verification of the theoretical stiffness is described using three different setups involving a hydraulic jack and spacers and confirms the stiffness calculations to within 1 percent. Experimental techniques, testing procedures, and special equipment designed for determining the complete stress-strain behavior of NX cores of both hard and soft rock are described. Typical test data are presented as force-displacement curves for two rock types, a marble and a granite.

Jan 1, 1972