Search Documents

By Anil K. Ray

Roof falls are one of the greatest hazards in underground coal mines worldwide. Due to stringent safety measures and extensive support system development, roof falls have been reduced significantly but they still persist in many underground coal mines. Some of the roof falls initiate with cutter roof or guttering. In the past, many factors have been identified as being responsible for the development of cutters and roof fall. These responsible factors can be broadly classified as stress related or non-stress related. In this paper the finer details of mining technique have been taken into consideration for better understanding of cutter roof and roof fall problems. Three dimensional finite difference modeling has been used to explain the mechanism of cutter development. Strain softening material behavior has been used to realistically simulate the cutter formation, and common cutting sequences as implemented in the field have been simulated. This was done with an objective to determine whether the cutting sequence has really any significant control over cutter formation or not. In addition to cutting sequences, the effect of cut length is also studied. The effect of step cutting and turning of crosscut into and away from major and minor horizontal stresses is also examined to see its influence on cutter development.

Jan 1, 2009

By Jarrod Bonsmann

"This paper presents the results of small scale testing to examine the effect of various importantparameters on the response of a vehicle due to the detonation of an explosive charge buried inthe soil below the vehicle. In particular, we were interested in examining what effect change instandoff distance, change in mass, and change in surface area would have on the loading applied.We examined the impulse delivered to the target in all cases and for the change in mass andchange in stand-off distance we examined impulse, kinetic energy, and acceleration."

Jan 1, 2012

By Bruce Vandenberg

Two tests were set up as part of the course given by Blasting Analysis International. Both tests were performed using the prototype Velocity of Detonation Recorder (VODR). The prototype has several limitations, which have been rectified for the production units.

Jan 1, 1990

By Arturo Ressi di Cervia

From the times when men in lacustrine environments drove wooden piles into the mud to elevate their dwellings, until the beginning of the twentieth century builders reacted to the conditions found in the location of their proposed structures by attempting to distribute their loads in ways that could be supported by the foundation's soils; or, if those were unsuitable, by moving the structure, whenever possible. While many major structures were built on stable ground (the pyramids were founded on rock), others were built on [ ]

Jan 1, 2000

By E. H. Izen

A thermal imaging borehole probe was designed and fabricated for the purpose of obtaining thermal images, through smoke, of objects and people in underground mines. The effort was basically unsuccessful; electrical noise, and possibly thermal noise, interferred with the desired signals to the extent that spatial resolution in the images was unacceptable.

Jan 1, 1980

By M. Mikhaylenko

Rhenium, molybdenum and tungsten are the elements demanded by high-end technologies. These metals are found in process solutions in forms of their oxyanions: ReO4-, MoO42- and WO42-. The later two can exist in forms of iso- and/or heteropolyanions. Basically all three metals demonstrate very similar chemical behavior in aqueous solutions. Unfortunately, in their mineral sources these elements commonly accompany each other, like pairs of rhenium-molybdenum or molybdenum-tungsten. Their economical separation is a challenging task.

Jan 1, 2012

By S. J. Rodgers

This report presents the results of in-mine studies to determine the severity of dust sources in conventional mining operations. Three underground coal mines were surveyed using gravimetric samplers and GCA RAM-1 continuous dust monitors. Two additional mines were surveyed using only GCA RAM-1 monitors. Data on dust control methods were acquired during the survey, also. The results indicated that cutting/drilling and loading out were the dustiest operations during a conventional mining cycle. Roof bolting, shot firing and product transport were less severe dust sources.

Jan 1, 1983

By D. M. Walters

To achieve safe and healthy working conditions in shaft sinking operations, ventilation, and where necessary cooling, must be provided. These requirements are considered for sinking vertical, sub-vertical and decline shafts. Regulatory requirements, determining air volumes and amount of cooling required, the various ventilation methods used such as force, exhaust, twin columns, air reversal using four gate systems and the equipment required to achieve this, are discussed. Consideration is also given to the sinking of single and twin declines using diesel equipment, calculating the air volumes required to dilute pollutants and the various methods for achieving this. Also discussed is the importance of having early ventilation design input to the overall design of the mine. In many cases ventilation can be the prime determinant for the size and configuration of the shafts or declines that have to be sunk.

Jan 1, 2009

By L. I. Gyrskia, Y. V. Andreev, T. N. Greiver, G. V. Petrov

Traditionally, chromite ores are regarded exclusively as a monomineral raw material for extraction of chromium. The results of the investigations indicate a wide range of PGM in the Ray-Iz chromites, amounting to 1-3 ppm PGM. The study of products of primary gravity concentration from heavily and lightly disseminated ores (Tsentralnoe deposit, Ray-Iz block), showed that the platinum-group minerals are concentrated in the tails and slimes of the processed products, containing 10-30 ppm total PGM. Preliminary data make it possible to conclude that an in-depth study of the platinum mineralogy of the Ray-Iz block chromite ores is necessary to develop a process that will produce both chromium and the PGM.

Jan 1, 2000

By Stephen C. Tadolini, Thomas E. Marshall, Cecil Banta, L. J. Prosser, Anthony T. Iannacchione

The Pittsburgh Research Laboratory of the National Institute for Occupational Safety and Health (NIOSH) endeavors to provide national and world leadership in the prevention of work-related illness, injury, and death. This is accomplished by using a scientific approach to gather information, assemble and create knowledge, then translate the knowledge and results into products and services. These products and services are then delivered to all personnel who can effect prevention. Obviously, the development and use of instruments to monitor mine roof conditions provides an opportunity to execute that mission. In the late 1990’s, based on observations at a number of underground limestone mines, only a few used roof monitors. Subsequently, NIOSH introduced the Roof Monitoring Safety System (RMSS) as an aid to roof inspection beyond traditional visual and sounding techniques. Initial expectations were that by gaining roof movement information, ultimately roof sag rates could provide indications of eventual failure. During this investigation, RMSSs were installed in 13 underground limestone mines in six states and this paper analyzes the data obtained at three of these mines. This paper also provides an overview of the system, data, analysis, and applications relevant to the RMSS.

By D. Symonds, A. J. Richins, M. G. Nelson

Mining activities at Kennecott and Park City are similar in that both districts began operation in the last half of the 18th century, and both operated on a large scale for many years. However, they are different for two important reasons. First, the mines in the Park City district were always underground. The city of Park City was above many of those mine workings. It remained in place after mining activity stopped, and as the town became an up-scale ski resort, property values increased and the tailings dumps became desirable building sites. In contrast, Kennecott eventually became an open pit mine, and the growing pit effectively consumed many of the small towns that had grown up around the underground workings. Even towns on the periphery of the open pit were razed to allow for the disposal of mine overburden. Second, almost all mining activity stopped in Park City in the early 1970s, just as the first rigorous environmental legislation in the United States was enacted. (The Ontario mine operated sporadically until 1982.) Many mine structures, waste dumps, tailings ponds and piles, and tunnels were simply abandoned as the mining companies ceased business or were bought out. Kennecott, on the other hand, has been in continuous operation for more than 120 years, so a closure plan hasn’t been finalized. Nonetheless, environmental and social problems have arisen, and the company has had to address them.

Mar 2, 2022

By Robert Fernie

Demographics and Infrastructure demands have led to a significant increase in construction of: deep basements for buildings and, trough structures for Highway and Rail/Metro. Concrete embedded walls used for temporary works can be incorporated into permanent works and because of this (and geological conditions) tend to be favoured in UK. This paper considers British practice in the provision of diaphragm (slurry) walls secant (true and pseudo) piled walls contiguous piled walls Plant utilisation, construction techniques, reinforcement placement, connections, propping, water tightness, tolerances, general UK practices and their relation to design practices are discussed. [ ]

Jan 1, 2000

By V. F. Parry

"INTRODUCTION During the war period the Bureau of Mines expanded its investigations on western coals principally in connection with Investigations of raw material resources for western steel production. Owing to the expansion of the steel industry, there was some concern regarding the availability of suitable coking coals; end because of the potential steel shortage, the production of sponge iron, using the lower-rank fuels, was considered. Work was conducted by the Bureau of Mines on exploration projects and on testing of coals both at the Central Experiment. Station at Pittsburgh, Pa., and at the Bureau of Mines Station at Golden, Cole.The results of these investigations are being published by the Bureau in several reports of investigations and technical papers. In making this resume of coal investigations, the work done by the Bureau of Mines at Pittsburgh in the Mining and Coal Carbonization Sections will be discussed and the investigations at Golden described in greater detail.INVESTIGATIONS OF WESTERN COALSThe Mining and Coal Carbonization Sections of the Coal Division, Bureau of Mines, under the supervision of A. L. Teeny es and J. D. Davis, respec¬tively, conducted many field investigations to locate and evaluate new sources of coking coals. Drilling explorations were made in Colorado, Wyoming, Utah, New Mexico, and Washington and revealed two important new reserves of coking coal. The first one studied was the Willow Creek bed at Kemmerer, Wyo., which was reported in 1945.3/ A recoverable reserve estimated at 11,200,000 tons was blocked out, and samples of coal were extracted for coking tests. The coking properties of the coal were not quite equal to those of Sunnyside coal, but it was indicated that a 50-percent blend of the Willow Creek with Lower Sunnyside will produce a satisfactory metallurgical coke based on Columbia steel standards."

Jan 1, 1948

By Gregg Hodges, Fred Schoenbrunn, Steve Slottee, Chad McCleary

"In December, 1999 Stillwater Mining Company (SMC) commissioned a new paste /cement backfill plant to supplement the existing sand backfill system for the cut and fill mining operation at it’s Nye, Montana mine. The new plant uses the Baker Process Deep Cone TM Paste Thickener to thicken the total concentrator tailings from 30% solids slurry to a 71% solids paste. This paper describes both general paste formation concepts and the evolution of the SMC paste plant operation from original design criteria, through problem solving and plant modifications, to the operation of the existing plant.Although the original process design was not effective for consistently producing and delivering acceptable paste to the stopes for backfill, SMC was able to make the mechanical and process modifications which allow the plant to now produce and deliver an acceptable product to the stopes. Ongoing test work is targeted at increasing the pumping range of the system, increasing the paste solids concentration from the Deep Cone Paste Thickener and reducing the operating and maintenance costs of the system.INTRODUCTIONThe authors would like to thank both Stillwater Mining Company (SMC) and Baker Process for their assistance in the preparation of this paper. Stillwater Mining Company chose not to participate directly in this paper due to time constraints, but was very helpful in answering questions concerning their approach to problem solving and specific details with regard to engineering criteria.This paper will begin with a general review of the technical and mechanical concepts in paste formation and then focus on the overall design, start-up and problem solving process for the paste backfill operation at SMC’s mine and concentrator near Nye, Montana."

Jan 1, 2001

By Gordon R. Sima

This contract is concerned with feasibility studies, design and fabrication of a prototype hand-held test instrument and a machine-mounted test Instrument for measurement of electrical shock hazards of mining machines. This report presents the proposed and detailed design of the hand-held test instrument and the machine-mounted test instrument. Theory of operation of each instrument is discussed and includes the operating parameters.

Jan 1, 1976

The U.S. Bureau of Mines (USBM) has developed a test procedure to compare the initiating strength of detonators by using adjustable-sensitivity liquid explosives. Various tests of detonator strength are currently used by the industry, but many of them do not quantify the ability of detonators to initiate detonation reactions in an explosive charge. The USBM used mixtures of nitromethane and ethylene diamine, the sensitivity being "fine-tuned" by 2-nitropropane. Military standard J-2, commercial No.6, and commercial No.8 detonators were evaluated using three test configurations: (1) axially immersed in the test explosive, (2) tip just touching surface of the explosive, and (3) immersed transversely in the explosive. Markedly different results were obtained for these three configurations, indicating that the directional effects are important. This explains why different detonator strength tests do not correlate well with each other. Some tests, such as the sand bomb and underwater, measure the total energy out-put, while other tests, such as the plate dent, test measure the energy in the axial direction. The USBM's test data indicate the importance of conducting the experimentation in the manner in which the detonator is actually intended to function.

Jan 1, 2010

The design of excavations in high displacement mining environments requires consideration of both the load and displacement capacity of the ground reinforcement and support systems. This paper is a case study on the design of point anchored rebar bolts using laboratory tests and field trials at the Ridgeway Deeps block cave. A laboratory testing program was carried out to measure the mechanical properties of the Strata Control Systems R27 Secura resin bolt which is currently being installed on the extraction and undercut level at the Ridgeway Deeps block cave. The aim was to quantify elastic, plastic and energy parameters for various bolt, mesh and plate systems. Experiments were performed on bar segments, bolt/plate systems, and bolt/plate/mesh/resin systems. The mechanical properties were calculated from tensile tests with a 500 kN Avery machine. Load-displacement data was collected from four different testing configurations. The laboratory results are compared with underground measurements and observations of bolt performance.

Nov 25, 2010

Entry of personnel under a vertical raise bored hole is not standard practice in Australia. Where access is required below a rise, mining operations must be confident that they understand the capacity of the ground control specified and installed. Physical modelling was conducted on Callie mine to evaluate the performance of 5 mm steel wire weldmesh secured to the base of a vertical raise bored hole of 1.4 m diameter. Joint orientation data was used with Unwedge to calculate a series of potential wedges likely to form within the rise. The mass of the most likely wedges were then replicated by collecting rocks in 5 kg increments (¦10 per cent), which were allowed to freefall onto installed mesh at the base of a 40 m vertical rise. The results indicate that two sheets of mesh can retain a freefalling rock of at least 20 kg mass although rupture of strands can result. This paper outlines the test conditions, expected results based on theoretical calculations and actual outcomes of the testing.

Nov 25, 2010

By I. L. Follington

This paper describes the research and development programme to develop a prototype underground auger mining system aimed at developing and demonstrating an underground auger mining system able to provide economic access to thinner (<1.8 m) coal reserves of South Africa. Data concerning the performance of modern coal augers under South African coal mining conditions were gained from a proven surface auger which operated across a range of coal types. These data were analysed and considered in conjunction with historical information regarding previous attempts at building underground augers dating back to the 1950s. Drawing on these data a prototype underground auger mining system, the BryDet BUA 600 underground coal recovery auger, was designed and manufactured by the BryDet Development Corporation in collaboration with Eskom and Cutting Edge Technology Pty Ltd with support from Anglo Coal and the Ingwe Coal Corporation Ltd. The prototype BryDet BUA 600 underground coal recovery auger commenced trials in March 2000 at the Matla Mine near Witbank in South Africa. The initial trials were undertaken in an open cut to facilitate the commissioning and training associated with a prototype mining machine. A total of 30 holes was augered in the box cut before the machine moved underground. The prototype BUA 600 first achieved the target penetration depth of 80 m in its third hole. The prototype BUA 600 is a new underground mining system which has passed early testing with ?flying colours? and could provide access to extensive underground coal reserves unmineable by conventional mining techniques both in South Africa and elsewhere around the world.

Jan 1, 2001

By P M. Bradbury

The nature of aggressive process chemical requirements typically in the Platinum Refinery Industries, lend themselves to the use of Polymer Composite Glass Reinforced plastics for pipework and other associated equipment in these types of Plants. This paper discusses the basic characteristics of a Polymer Composite glass reinforced piping system and gives sample examples of applications in current present day use.

Jan 1, 2006