Search Documents

By J. Alexis, G. Ye, E. Burström

Over the past twenty years the 3 MW DC arc furnace at MEFOS has been frequently used for development of new processes. These processes include recovery of valuable metals from slag, sludge and dust from steel and other metallurgical industry, treatment of ashes from power plant and incinerators, smelting reduction of minerals and zinc recovery from EAF dust. The process characteristics of the DC arc furnace operation in terms of: ? selective reduction, ? total reduction, ? process stability and flexibility, ? dust carry-over, ? thermodynamic conditions provided in the hot spot area, ? precision in composing slag products These are analysed and described in this paper based on technical results from selected test campaigns over the years and thermodynamic considerations. The electromagnetic properties of DC arcs beneath the electrode have been studied by CFD simulation. The calculated result enables us to understand some interesting technical phenomena observed. The heat balance has also been considered based on data obtained from test campaigns and heat balance calculation.

Jan 1, 2004

By S. J. Lötter

Analysis of the major and minor components of raw zircon as well as plasma-dissociated zircon was undertaken using inductively coupled plasma optical emission spectroscopy (ICP-OES). Microwave-assisted acid extraction as well as flux fusion using lithium tetraborate were investigated as digestion methods. Microwave-assisted acid extraction samples were analysed with matrix-matched standards. The most successful microwave-assisted acid extractions yielded 44.3(1), 49.75(7), 78.3(3) and 90.0(7) per cent recovery for Zr, Hf, Al, and Fe respectively using sulphuric acid. In no instance was acid extraction capable of complete digestion of the sample matrix. A standard addition method was applied to the flux-fusion samples due to the high complexity of the sample matrix. Method validation for the flux fusion procedure was performed using the SARM 62 certified reference material (CRM) with acceptable recovery ranges being based on the 95 per cent confidence intervals of the CRM. Successful analyses were achieved for Zr, Hf, and Ti with apparent content of 66(6), 1.7(1) and 0.15(1) per cent respectively.

Jan 1, 2012

By Gerald L. Stolarczyk

Safe and efficient coal extraction requires advanced radar subsystems that can be mounted on cutting drums of coal cutting machines. A look-ahead radar (LAR) must solve the radio geophysics problem of transmitting an electromagnetic (EM) wave through at least 20 feet (6.1 meters) of coal to an air- or water-filled void. The reflected EM wave must be processed in the radar electronics to determine the physical distance to the void. Horizon sensing enables selective cutting near the undulating sedimentary rock boundaries of the coal bed to address coal quality and ground control issues. Both sensors require subsystems for dynamic electric power generation, real-time measurement of drum rotation angle, detection of reflected EM waves, and processing to determine distance through coal and RF modem transmission of measured data to the mining machine. This paper describes the development of the subsystems and field test results.

Jan 1, 2006

By A. Kale

A chlorination pilot plant having capacity to produce 5?10 kg/hr of titanium tetrachloride is in operation at the chlorination facility in Mintek. The bubbling fluid bed chlorination plant can be operated in batch and/or continuous process to study the chlorination kinetics of various feedstocks. The chlorination of titaniferrous ores to produce titanium tetrachloride (TiCl4) was carried out during the commissioning of the pilot plant and also as part of the titanium programme carried out at Mintek. TiCl4 is a basic raw material for producing commercial titanium dioxide pigment and titanium metal. This paper discusses the challenges faced during the commissioning and operation of the chlorination pilot plant. It also discusses the effect on the auxiliary facilities and instrumentation as a result of the harsh operating conditions of +1000°C and use of corrosive gases like chlorine and titanium tetrachloride. It discusses the effect of physico-chemical properties of the titanium tetrachloride and iron chlorides. The effect on the chlorinator refractory lining due to heating and cooling of the chlorinator is also discussed. Besides the special provisions made during the design of the chlorinator, this paper also discusses the operational experience and possible solutions to be implemented in future. Keywords Fluid bed chlorination, titanium ore chlorination, titanium tetrachloride (TiCl4) production using fluid bed technology.

Jan 1, 2011

By E. D. Wilson

A study of factors related to subsidence was specified in a project proposal entitled "Structural Analysis of Block-Caving Operation, San Manuel Copper Mine, Pinal County, Ariz.," approved by the Bureau of Mines early in 1953. This proposal was designed by Charles H. Johnson, then chief of the Base Metals Branch of the Minerals Division, Washington, D. C., assisted by Dr. Leonard Obert, chief of the Applied Physics Branch, Region VIII (now Region V), College Park, Md., and E. D. Gardner, chief mining engineer, Bureau of Mines, Washington, D. C. It read as follows: This project is a study of the mechanics of undercut block caving in a deep ore deposit. The San Manuel is a low-grade disseminated copper deposit containing nearly a half billion tons of ore lying at depths of 500 to 2,000 feet. Development is just starting. Production is to begin in 3 to 4 years (in 1956) at a rate of 30,000 tons of ore a day, or 60,000 tons of copper a year. A Government loan of $90,000,000 /subsequently increased to $94,000,000/ and a long-term Government purchase contract support the capital investment, which will total about $110,000,000.

Jan 1, 1957

By K. Thuro, R. J. Plinninger

ABSTRACT: Determining tunnel stability is a key issue during preliminary site investigation. In contrast, problems of excavatability have been largely ignored. While the choice of an economic tunnelling method is admittedly a clear priority in the planning stage, special investigations focus-sing on rock fragmentation (e.g. drilling or cutting performance, rock mass blastability or tool wear) are rarely carried out. This paper explores possibilities to quantify key parameters for rock mass excavatability in drilling, blasting and cutting by TBMs and roadheaders. RÉSUMÉE: La détermination de la stabilité du tunnel est une question clé lors des études prélimi-naires. En revanche, les problèmes d'excavabilité sont souvent en grande partie ignorés. Tandis que le choix d'une méthode de percement économique est évidemment une priorité claire dans l'étape de planification, des investigations spéciales se concentrant sur la fragmentation de la roche (par exemple le comportement de la roche au forage, à l’excavation ou au dynamitage et l’usure des outil) sont rarement effectuées. Cet article explore les possibilités pour quantifier les paramè-tres clé de la roche lors d’excavation par forage, dynamitage, au tunnelier (TBMs) ou à l’excavatrice. ZUSAMMENFASSUNG: Beim Tunnelbau wir meist die Vorhersage der Stabilität des ausgebrochenen Hohlraums als Schlüsselfragestellung betrachtet. Im Gegensatz dazu werden Probleme der Gebirgslösung weitgehend ignoriert. Während der Wahl einer wirtschaftlichen Vortriebsmethode während der Planungsphase meist noch eine gewisse Priorität beigemessen wird, werden spezielle Untersuchungen zur Gebirgslösung (Bohr- oder Schneidbarkeit, Sprengbarkeit oder Werkzeugverbrauch) nur sehr selten durchgeführt. Diese Publikation zeigt Möglichkeiten der Quantifizierung von Schlüsselparametern für die Gebirgslösbarkeit auf, also der Bohr- und Sprengbarkeit, der Fräsbarkeit mit Teilschnittmaschinen und der Schneidbarkeit mit TBMs.

Jan 1, 2003

By Robert J. Timko, Charles D. Taylor, Edward D. Thimons, Tom Mal

A test system was developed for measuring airflow in the National Institute for Occupational Safety and Health (NIOSH) ventilation gallery using a three-axis ultrasonic anemometer. The gallery was used to simulate face airflow conditions in underground mines having a blowing curtain. Airflow data collected at multiple sampling locations between the face and the end of the curtain were used to draw airflow profiles for different curtain setback distances, intake flow quantities and entry widths. In addition, methane was released at the face, measured at the sampling locations, and displayed as methane distribution in the area between the curtain and the face. Entry geometry had a significant effect on airflow patterns, and the flow patterns affected the distribution of methane in the entry. Flow measured at and parallel to the face was a good predictor of methane dilution and removal within two feet of the face.

Jan 1, 2005

By Eric E. Cather

A mineral survey of a portion of the Lake Eleanor RARE II area (No. 5807), Trinity County, California, was done by the U.S. Bureau of Mines and U.S. Geological Survey (USGS). Approximately 8,650 acres (3,500 ha) of the Lake Eleanor RARE II area not examined for this report had been previously investigated by U.S. Bureau of Mines and U.S. Geological Survey personnel and published as part of USGS Bulletin 1371-B, (Hotz, 1972) Mineral Resources of the Salmon-Trinity Alps Primitive Area, California. The report showed that the section included in the rake Eleanor RARE II area contained no metallic mineral resources. Geochemical sampling indicated that the Lake Eleanor RARE II area contains no potentially important mineral resources. About 4,650 acres (1,880 ha) of the eastern part of Lake Eleanor RARE II area were examined for this report. The Bureau of Mines was responsible for detailed examination and sampling of mines, prospects, and mineralized zones; the Geological Survey conducted geological, geochemical, and geophysical studies of the area. This area is underlain mainly by granitic rock and serpentinite.

Jan 1, 1981

By U. Olsson, M. Ramström

"The IREDES1 Special Interest Group (SIG) for drill rigs has been active since its launch during MineExpo 2000 in Las Vegas, Nevada, United States. SIG for drill rigs is responsible for the development of an IREDES drill rig profile, including the exchange of production planning, performance, and quality reporting data between various kinds of drill rigs and the databases used by the operating mine. During 2001, a first draft of the drill rigs profile was jointly prepared by drill rig suppliers, mining companies, and third-party suppliers and reviewed during several SIG meetings. The profile for prototyping projects was released in mid-2002; the first official IREDES release was based on feedback received from these projects.In 2002, LKAB and Atlas Copco decided to carry out an IREDES prototyping project using the Simba L6C production drill rig. The goal was to verify the drill rig profile and identify potential problems prior to the official release. This was done by implementing the IREDES prototype version into LKAB’s production planning and Simba rig control systems. The Simba rig control system was designed to handle drill plan and logging information coming from the mine planning system. In parallel to this, the mine production system was adapted for drill plan export and logging data import in IREDES format.This paper presents the most recent results of the IREDES prototyping project. Results from late 2002 show that the basic architecture of the drill rig profile works and that a common language for data exchange, IREDES, will be a central requirement for future mine automation.As a result of the IREDES prototyping project, the IREDES standard was approved at the IREDES board meeting held at the 2003 CIM Annual Conference and Exhibition. Soon thereafter, IREDES compliant products, including drill rigs and mine production planning systems, were put on the market."

Jan 1, 2005

By R. J. MacLeod

"INTRODUCTIONThe removal of water or liquid from slurries and solutions is a procedure generally present in many process industries. This has prompted the development of many mechanical and thermal devices with which, I have no doubt you are al1 familiar.In the mining industry, beneficiation of ores necessitates ' the removal of water or other 1iquid from the concentrate material. The most common method of accomplishing this is by means of thickeners, vacuum filters and rotary dryers, generally all three and in that order;The use of spray drying techniques to obtain the same end has many advantages and these will be outlined here.THE PRINCIPLE OF SPRAY DRYINGA Spray Dryer consists of a cyclone shaped chamber where hot air and atomized concentrate are introduced in the upper section. (Sec figure No. 1). Efficient mixing of these two streams produce dry concentrate and moist spent air, both of which are removed from the base of the chamber.Thermal dewatering involves the product ion of heat and spray drying has no special requirements in this area. Generally a direct fired air heater is used and the products of combustion whether they stem from the use of gas, oil or coal fuel go into the spray dryer along with quench or dilution air which is used to reduce the combustion gases to the desired temperature. This generally lies in the range of 1,000 to 1,600° F. In spite of these relatively high inlet temperatures, the spray drying process eliminates the need for refractory lining or indeed any special heat resistant metals except on the air inlet ducting. Waste heat may also be used even if a significant amount of contamination is present."

Jan 1, 1972

By S. K. Kawatra, A. K. Bakshi, T. C. Eisele

An on-line rheometer, suitable for use with slurries, has been developed at Michigan Technological University. This rheometer can be used with both Newtonian and non-Newtonian slurries, and produces complete shear-rate/shear stress curves which characterize the time-independent rheology of the slurry. The sensor utilizes the Hagen-Poiseuille equation and Boyle's Law to calculate the shear rate, slurry flowrate, and shear stress from a series of pressure measurements. The design of the unit allows the measurement sample to be continuously collected from operating process streams in the often-hostile on-line environment. The shear rate/shear stress curves can be used to conveniently calculate the apparent viscosity at any given shear rate, and also to measure any yield stress or other deviations from Newtonian behavior.

Jan 1, 1999

By R. B. Krog

As part of its mining health and safety research program, the National Institute for Occupational Safety and Health (NIOSH) conducted a longwall methane emission and mining time study at a mine operating in the Pittsburgh Coalbed to access the methane emission consequences of mining a longer face. The methane emission contributors from the mining of a longwall face are: 1) gas released from the coal broken by the shearer, 2) gas emitted from the coal on the face conveyor, 3) gas emitted from the coal transported on the belt, and 4) background gas emitted from the coal face and from the adjoining ribs. Based on the results of the study, a set of site-specific mathematical formulas and constants were developed to characterize each of the four longwall emission contributors. The mathematical formulas were then applied to longer longwall face mining scenarios to predict the methane emissions from these faces.

Jan 1, 2006

By C. M. McKinney

This report contains Bureau of Mines analyses of 291 samples of crude petroleum from the Gulf Coast Area of Louisiana and Texas. Included are 65 analyses from 51 Louisiana fields and 226 analyses from 216 Texas fields. Analyses from the Texas fields include 90 from 58 Upper Gulf Coast fields, 47 from 28 Middle Gulf Coast fields, and 89 from 40 Lower Gulf Coast fields. The analyses represent fields that produced 1,000 barrels or more per day during at least one of the years 19.57 through 1961, with the exception of 23 analyses from the Texas fields. The fields considered are listed by state and geographical groupings, with field names arranged alphabetically within each grouping. The tabulation also includes information concerning the geological sources of the samples. General characteristics of the crude oils and analytical and computed data determined from the analyses are summarized. Crude oil production data are given for the fields for 1960 and 1961 and are cumulative through 1961.

Jan 1, 1963

By Sheryl D. Gallagher

The project consisted of filling an abandoned underground limestone mine to facilitate construction of a new entrance ramp to I-470 in Lee?s Summit, Missouri. Due to collapse of mined areas near the project site, design included determination of the limits of remediation for the project and minimum construction requirements for mine infilling. The Judy Company, contractor selected for the mine infilling, experimented in the laboratory with several grout mixes to determine the appropriate mix for the project. Infilling was accomplished from the ground surface, and camera observation was used to monitor the barrier wall construction and infilling process. It was discovered that some of the mapped rooms were larger and some were smaller than indicated on the construction plan.

Jan 1, 2009

By R. S. McDonald

Auburn began operations 40 years ago with an office in Sudbury, Ontario, Canada, to provide services to Inco Limited. Over the next 40 years, operations expanded considerably, with projects being undertaken around the world, servicing the smelting and refining industry. Operating bases have been established in Canada, United States, Mexico, Chile, and Spain, with further growth expected to continue with an operating presence in South Africa. The Auburn Group of companies has serviced the smelting and refining industry for over 35 years. Auburn services a variety of metallurgical plants, and our worldwide experience has gathered considerable knowledge on industry processes and maintenance solutions. Today, the ?Business of Smelting? tackles demanding challenges, and operators search for opportunities and solutions to improve smelter maintenance, reduce operating costs, and decrease downtime. The Auburn Group has developed project teams, technologies, and equipment that provide specialised and innovative solutions to the non-ferrous metal industry to help address these challenges. Our Furnace Services team offers a variety of repair and maintenance services for metallurgical furnaces. Our specialised team has proven methods for completing projects quickly and safely. Our worldwide experience includes turnkey project management, construction, and various scopes of work for demolition and refractory repairs on all types of smelting and refining furnaces. Auburn developed the Results FirstTM programme to provide optimized solutions and results for smelter projects. The programme utilises a proven three-step model for improved results for schedule, budget, safety, and ramp-up to production. Our experienced Project Management teams can handle the planning and construction management of capital projects and plant shutdowns. Our projects have involved smelter/refinery modifications, oxygen plant installations, and sulphuric acid plant audits and maintenance. Our Equipment & Products division supplies specialised equipment and products, which are used in the metals industry for plant maintenance tasks. Our capability to design unique equipment, combined with our ability to source products worldwide, makes us a useful resource to find the best-suited equipment to meet the work-site demands. We specialise in custom remote-control units to handle specific maintenance solutions for smelters and refineries, and custom equipment designs for catalyst handling for Acid Plant maintenance. Our extensive knowledge of and experience with industrial technologies allows us to provide a wide range of Industrial Services. These services include vacuuming, high-pressure water blasting, chemical cleaning, pelletizing, dredging, ore bin clearing, roaster repairs, baghouse/ESP services, and manpower supply for both industrial plants and mines. Auburn?s combined strength of personnel experience, knowledge of industry processes, innovative project methods, and equipment technology make Auburn a unique resource for problem solving on every facet of smelter operations.

Jan 1, 2006

By Steven Norris, William Moler, Michael Cole, Patrick Doig, Debi Lewis, Craig Pyle, Matthew Crow

The recently completed Lower Northwest Interceptor Program (LNWI) in Sacramento, California comprises, ten pairs of micro tunnels totaling 4,369 m (14,417 ft),three horizontal directionally drilled bores totaling 956 m (3,154 ft), and two large diameter tunnels under the Sacramento River totaling 1,198 m (3,953 ft). This paper briefly summarizes surface and subsurface conditions, and planning and design considerations. It then goes on to describe problems encounterd with each trenchless crossing, as well as lessons learned with respect to shaft construction, ground control at shafts during tunnel break-in and break-out, frac-out and heave, settlement, obstructions, coordination with permitting agencies, and application of geotechnical baseline reports.

Jan 1, 2007

By Z. Zhang

The author recently has reviewed the publications on the slag-related research in China since the Sixth International Conference on Molten Slags, Fluxes and Salts in June, 2000. In fundamental aspects, the physical property predictions and measurements, slag-metal reactions, slag-refractory reactions have received close attention, and are briefly described here in this report. More than half of slag-related publications deal with plant investigations due to the requirement of technological improvements and environmental protection. In the present paper, the research on slags in various treatments related to clean steel production and the utilization of the waste slags is briefly reviewed.

Jan 1, 2004

By H. D. B. Wilson, W C. Brisbin

The Thompson-Moak Lake nickel belt lies along the root of a Precambrian mountain range of the island-arc or alpine type. This range coin-. cides with the boundary between the Superior and Churchill blocks of the Canadian Precambrian shield. The nickeliferous peridotites and nickel ores occur along a negative gravity strip, which also coincides with strong thrust faulting and the axis of greatest deformation of the mountain range. Similar structures and highly nickeliferous peridotites occur in present-day island arcs. Much of the belt is covered by Paleozoic rocks, but a length of 270 miles may be explored by present-day methods. Nickel deposits have been located along 60 miles of the belt. The length of the favorable structure and the size of the known deposits suggest that this will be one of the world's major nickel regions. The regional gravity anomalies, which consist of a branching negative strip bordered by two positive strips, are best explained by major warps of a crust consisting of a granitic and basaltic layer. The ore deposit

Jan 1, 1961

By S Hu, P Ni, H Xu, P Chen

Indosinian (T) orogeny amalgamated the Mongolia-Xingan fold zone, the North China continent, the Yangtzi platform and the SE China fold zone into a unified continent. The early to middle Yanshanian (J-K1) orogeny created a Cordilleran type active continental margin in East Asia, reactivated the consolidated East China continent, and generated a large amount of granitoids, calc-alkaline volcanics and W, Sn, Mo, Cu, Au, and U ore deposits. The late Yanshanian (K2) orogeny began a transition to the western Pacific type continental margin. A tensional environment led to the development of peralkaline magmatism and tne formation of continental basins with red beds. The Himalayan (Tr-Q) orogeny was characterised by a backarc spreading and rifting regime. The dominant magmatism was continental basaltic.

Jan 1, 1995

By Edward L. McHugh

The Thousand Lakes Wilderness has no known economically significant mineral resources. However, the geologic setting of the Wilderness indicates a potential for the discovery of geothermal resources. INTRODUCTION The Thousand Lakes Wilderness occupies 16,335 acres (6,611 ha) in eastern Shasta County, California. A mineral resource study of the area was authorized by the Wilderness Act of 1964 (Public Law 88-577). Mining records and published information were examined, and field investigations conducted in 1979. The Wilderness is about 50 miles (80 km) east of Redding and 12 miles (19 km) south of Burney, California. It lies in the Cascade Range of California. Relief is more than 3,000 feet (910 m); elevation is greatest at the summit of Crater Peak, 8,677 feet (2,645 m).

Jan 1, 1982