Search Documents

By Osamu Taki

The development of new auger bits for soil cement column drilling equipment has made it possible to create a homogeneous mixture of soil and cement-reagent slurry. As a result, soil-cement columns are used for foundations of houses and buildings, with reliable results, as demonstrated by many field projects and laboratory tests. This paper presents and discusses construction techniques for soil-cement columns, characteristics of the soil-cement solid, quality control, bearing test results, and soil-cement foundation design procedures.

Jan 1, 1992

By Vinícius Resende Domingues, André Pacheco de Assis, Bernardo Cascão Pires e Albuquerque

"The increasing demand for underground works in urban centers, and in particular the need to build undercrossing tunnels, requires constant evolution in building techniques in order to achieve success and safety. In the case of Brasilia, capital of Brazil, in order to preserve an important avenue (Eixo Monumental), where are located many historical monuments, the construction of a tunnel was envisioned as an option to interconnect the National Stadium (on one side of the avenue) to the Convention Center Ulysses Guimarães (on the other side). The excavation design is comprised of a coverage smaller than one diameter, height of 7.5 m, width of 9.0 m and length of 25 m. In order to enable a negligible influence on the avenue’s usage, the structure is designed as a portico system composed of pipe canopy. In this context, this study presents the portico analytical solution computed with the aid of the software Mathematica and a numerical solution using the software ABAQUS. INTRODUCTION Undercrossing tunnels are increasingly common in urban centers as alternative roads or as access to underground works of large dimensions (stations and parking lots). The geomechanical conditions of the soil mass, not always favorable, and the low distance between tunnel’s ceiling and the surface require intense treatment of the soil massif and execution of a rigid support system. The importance of the road just above the undercrossing tunnel emphasizes the need for a highly competent monitoring system because existing structures require minimum allowable displacement and do not allow the interruption of traffic. The soils that are excavated for the construction of undercrossing tunnels are composed, in most cases, of layers of fill and / or soft soil or weak rock, showing stability problems when subjected to tunneling operations. The combination of low coverage and week ground is solved by soil improvement techniques and strengthening of the excavated cross-section with further advance with the so-called New Austrian Tunneling Method (NATM). Another option is to build structural frames that support the surface. In this research, and based on the context of a case study, we propose the study of the construction technique comprising a portico structure composed of pipe canopy. For this paper, the technical standards used are the Brazilian ones as the case study refers to this country."

Jan 1, 2016

The papers contained herein summarize results of various recent Bureau of Mines investigations in the area of mine power distribution systems. They are based on information from Bureau personnel, contractors and grantees, and Mining Enforcement and Safety Administration. Conclusions drawn from a series of parameter measurements on mine power systems, taken over a 3-year span, are presented. Personnel and equipment hazards due to faults on isolated, solidly grounded, and resistance grounded three-phase systems are discussed. Two papers cover dc applications of circuit breakers, including a novel protection scheme for trolley lines. The methods of suppressing induced arcing currents and voltages in a-c machines are evaluated. An evaluation program for ground monitors is described. Acceptance test procedures and the importance of various paparameters for trailing cable splice are covered. A number of techniques for locating faults in trailing cables are described.

Jan 1, 1975

By Ernesto Gustavo Maffia

En la actualidad, el moldeo por inyección es una tecnología muy utilizada en el procesamiento del plástico pues permite fabricar formas geométricas complejas. Para fabricar los moldes se utiliza ampliamente la aleación C17200 (Cu-2%Be), pero están en desarrollo algunas alternativas con aleaciones base cobre libres de berilio, que tienen valores de dureza por encima de los 30 Rockwell C y buena conductividad. Las aleaciones base de cobre, tipo CuNiSiCr son las más adecuadas como reemplazo. El siguiente trabajo trata del estudio y desarrollo del proceso de fabricación, por fusión, colado y conformado, de una aleación tipo CuNiSiCr de alta dureza y buena conductividad para ser utilizada en la fabricación de moldes de inyección para la industria del plástico. Los resultados preliminares de esta investigación demuestran que a través del aumento sistemático en el contenido de níquel y silicio se consigue un aumento de la dureza (>32 Rockwell C) y una aceptable conductividad eléctrica (˜25%IACS). El fenómeno segregación interfiere fuertemente en los tratamientos termomecánicos, pues se forma una segunda fase interdendrítica, de características frágiles, que genera fracturas en el conformado. Los resultados demuestran que la aplicación del recocido total y control de la temperatura durante la forja minimizan este problema.

Aug 7, 2018

By B. M. Hamilton

"IntroductionTHE PROCEDURE and technique for drilling holes has probably undergone as great a change during the past ten years as any one of the other operations conducted in hard-rock mining. During this period, we have seen a change from the heavy leyners and drifters to the light jackleg type of drill machine; from steels that were forged and hardened on the bit end to the inserted •carbide-tipped rod, from the necessity of providing special bit-end fabrication and beat treatment of shank steels to the simple grinding or turning of a plain section on a shank with no heat treatment required for bit attachment.When the steel maker was first called upon to manufacture a hollow drill rod, it was required that the steel must not only have sufficient strength and fatigue resistance to cope with the stresses of service, but also must be capable of being heat treated on the bit end to a high hardness for resistance to wear and abrasion . Little was known at that time about alloy steels and the beneficial effects to be gained from additions of chromium, nickel , and molybdenum. So it was that the plain 0.80 per cent carbon analysis was selected, since it had already proven to be a suitable grade for chisels, hammers, and other such shock tools. This grade has long endured the test of time and is still used in considerable tonnage today, particularly by the construction industry.As the metallurgist learned more about the influence of alloying elements, a new hollow drill analysis was placed on the market in the early 'thirties'."

Jan 1, 1954

By Martin D. Conyac

Results of the minerals survey indicate low potential for the discovery of placer gold along Deck Creek aid for copper, silver, and gold in PreTertiary rocks within the boundaries of the Lake Fork RARE II area. Potential for oil, natural gas, coal, and geothermal resources is negligible. No evidence of economic mineral resources was found during the examination of the study area, and no assays of rock or placer samples taken from the urea showed economic mineral values. There are no producing or developing mines within the boundaries o of the lake Fork study area. SETTING Mining Districts The Lake Fork RARE II area is on the eastern fringe of the Cornucopia Mining District, which is centered about 6 mi west. It is also on the western edge of the Homestead district, centered about mi east.

Jan 1, 1983

By Álvaro Ordóñez Núñez

El presente texto describe la forma de realizar la extracción y recuperación de cobre y zinc a través del empleo del hipoclorito como agente oxidante y del amoniaco como agente acomplejante de los cationes metálicos. Entre las ventajas de su utilización respecto a la lixiviación tenemos: que las soluciones obtenidas son más limpias y los interferentes como el hierro, manganeso y aluminio se precipitan como óxidos hidratados en este medio, facilitando los procesos posteriores de recuperación de metales. Asímismo, se evita la etapa de extracción por solventes, obteniéndose de ese modo un precipitado metálico o de electrodeposición directa desde las soluciones de lixiviación final. En ese sentido, la extracción y recuperación a partir de minerales complejos con altos contenidos de carbonatos mezclados íntimamente con sulfuros secundarios en condiciones normales es la alternativa técnica económica viable.

Dec 1, 2012

Confidence in the strength of the U.S. economic recovery was considerably enhanced by third quarter 1983 profits, which showed a 12.8-percent increase over those in the second quarter (table I). Although the increases were not as great as between the first and second quarter of 1983, profits have grown each quarter since fourth quarter 1982. Both total profits and profits per unit of output increased, which the Bureau of Economic Analysis (BEA) attributes to decreases in labor and nonlabor costs (per unit of output), as well as to moderate price increases. [ ] A number of durable goods sectors, however, continue to show profit declines, especially electrical and non-electrical machinery. Profits in the primary metal industry are still negative, but the economic picture of this industry is improving. Between the second and third quarters of 1983, capacity utilization increased somewhat in primary metal manufacturing and stone and earth mineral mining but did not change at all in metal mining. Capacity utilization in metal materials increased from 47.4 percent in the fourth quarter of 1982 to 64.2 percent in the third quarter of 1983 (table 2).

Jan 1, 1983

By G. B. Amicucci

Golden Sunlight Mines Inc. operates an open-pit gold mine and cyanidation plant about 11km (7 miles) northeast of Whitehall, MT. Golden Sunlight is a subsidiary of Placer Dome US Inc. Mining is accomplished with conventional open pit drilling, blasting and hauling methods. The mining rate is about 102 kt/d (113,000 stpd). Gold occurs as fine-grained disseminations in a pipe-shaped breccia and in immediately adjacent country rock. The ore body is low grade, averaging 2 g/t (0.059 oz per st) of gold. The metallurgical plant uses conventional carbon-in-pulp (CIP) technology. Daily throughput averages 6.5 kt (7000 st). Recoveries are enhanced through a sand tailing retreatment facility while a preaeration process reduces operating costs. The low grade ore dictates that maximum mill throughput at the desired grind size be maintained. Therefore, in October 1988, an Armco Autometrics (now Denver Autometrics) particle size monitor (PSM) 400 was commissioned. The PSM 400 is an on-line instrument. It measures particle size and percent solids in a slurry stream. The PSM pulls its own sample, deareates the sample and passes it through diametrically opposed ultrasonic sensors. The unit uses ultrasonic sound to measure the deareated slurry stream's particle size and percent solids.

Jan 1, 1991

By S. Lubbe

South Africa and Australia are the biggest suppliers of zircon sand to the international zirconium industry. However neither South Africa nor Australia is well known for zircon beneficiation. Geratech Zirconium Beneficiation Ltd (GZB) continued with additional research on sodium hydroxide (NaOH) cracking of zircon sand during 2002-2003. In 2003 GZB started extracting zirconium from zircon sand by means of NaOH cracking on a commercial scale. Experience has shown that temperature profile and atmospheric control inside the furnace is crucial for the beneficiation of zircon sand. Silica carryover to zirconium chemicals could result if a high temperature is used. Once the sodium silicate is extracted from the sodium zirconate and dissolved in hydrochloric acid, two distinct routes can be followed to precipitate various zirconium chemicals. The most common route is to precipitate zirconium oxychloride crystals (ZOC), with subsequent purification from all contaminants (crystal route). Less known is the process (liquid route) that involves the direct precipitation of zirconium basic sulphate (ZBS). This route will yield a less pure product, with contaminants such as silica and titanium. An important factor in this route is the prevention of silica gel formation, which could hamper final product filtration. For applications like paint drying (zirconium octoate) or antiperspirants (zirconium hydroxychloride) low levels of contaminants have no effect on the final product. The advantage of the liquid route is fewer production stages compared to the crystal route. The disadvantage of the liquid route is that the market for the products will be significantly smaller. The optimum solution could be a plant design that could cater for both routes. Another example of an application of zirconium chemicals is the use of ammonium zirconium carbonate (AZC) in the paper industry. Zirconium basic carbonate (ZBC) is dissolved in ammonium carbonate to produce AZC solution. AZC is used mainly in European countries in the paper industry. For example, carton boxes were initially produced with formaldehyde as the binder, however, it has now been replaced with AZC since formaldehyde is considered toxic. AZC reacts with the cellulose fibres in the paper to act as the binder. The resulting product is not toxic, and printing ink dries very quickly due to the porous paper structure. Other applications of zirconium chemicals involve the use of acid zirconium sulphate tetrahydrate (AZST), zirconium orthosulphate (ZOS), potassium zirconium carbonate (KZC), and zirconium hydrous oxide (ZHO). Fluoride-based zirconium chemicals like zirconium tetra-fluoride (ZrF4) and hexafluoro-zirconic acid (H2ZrF6) are used in the aluminium industry. Zirconium oxide (Zr02) can be produced from any of the abovementioned precipitated chemicals via a high-temperature decomposition process. The physical properties of such oxides can differ tremendously, depending on the final application. The fired density of sanitaryware is typically 5.8 g/cm3, compared to milling media at >6.1 g/cm3. The required fired density is achieved by controlling the precipitation and decomposition conditions for these two oxides. The same applies to stabilized and mixed oxides, for example where zirconium oxide acts as an oxygen carrier in fuel cells.

Jan 1, 2012

By Clarence Hall, Spencer P. Howell

Among the more important factors involved in the use of high explosives in blasting operations is the means employed to bring about the detonation of the charge. When flame is applied to high explosives many of them may burn if not confined; but all of them when burning under certain conditions of confinement may detonate. Detonation may also be effected by mechanical means, such as frictional impact caused by a blow or by rubbing between surfaces. By this means, however, the full effect of the explosive charge may not be developed, so that a partial detonation, often accompanied by the burning of the explosive, results. When nitroglycerin was first used it was fired by the application of flame, but considerable difficulty was experienced in exploding it with certainty and in obtaining uniform resl'llts. In 1864 Allred Noble, a Swedish engineer, discovered that nitroglycerin could be surely and completely detonated by exploding in contact with it a small quantity of an initiatory explosive. Mercury fulminate was the substance then found capable of producing the best results There are many other fulminates and other substances that will produce complete detonation of commercial" high" explosives, but detonators or electric detonators containing mercury fulminate as the characteristic ingredient are still almost exclusively used in this country. The term" detonator" is used in the publications of the Bureau of Mines to designate what the miner calls a "blasting cap "-a copper capsule containing a small quantity of some detonating compound that is ignited by a fuse. The term" electric detonator" is applied to a blasting cap that is similar except for being ignited by means of a small wire which is heated to incandescence or fused by the passage of an electric current. One of the conditions prescribed by the Bureau of Mines for a permissible explosive a is that it shall be :fired by a detonator, or preferably an electric detonator, having a charge equivalent to that of the standard detonator used at the Pittsburgh testing station. A further requirement is that this charge shall consist by weight of 90 parts of mercury fulminate and 10 parts of potassium chlorate (or their equivalents). At the request of a manufacturer of permissible explosives, an investigation was undertaken by the bureau to determine the relative strength of detonators and electric detonators having different compositions. The tests of electric detonators herein reported were conducted by H. F. Braddock, junior chemist; J. W. Koster, J. E. Tiffany, junior mining engineers; and A. S. Crossfield, junior explosives chemist, at the Pittsburgh testing station of the bureau. Similar tests of detonators were not conducted because it was believed that the results would not show sufficient variation to warrant such tests. It is hoped that the conclusions drawn from the tests made will be of service to those using explosives by enabling them to select the grade of detonator or electric detonator that will insure the most effective results. The conclusions are given in this bulletin, which is published by the Bureau of Mines as one of a series of publications dealing with the testing of explosives and the precautions that should be taken to increase safety and efficiency in the use of explosives in mining operations. The results of tho experiments described in this bulletin show that the average percentage of failures of explosives to detonate was increased more than 20 per cent when the lower grades of electric detonators were used instead of No. 6 electric detonators, and was increased more than 50 per cent when these lower grades were used instead of No. 8 electric detonators. It is noteworthy, however, that when sensitive explosives, such as 40 per cent strength ammonia dynamite (p. 33), were tested under conditions ideal for detonation, the same energy was developed irrespective of the electric detonator used. When tests were made with a less sensitive explosive, such as a 40 per cent strength ammonia dynamite containing nitrosubstitution compounds (p. 32), the energy developed increased with the grade of the electric detonator used. For example, the average efficiency of four different explosives was increased 10.4 per cent when a No.6 electric detonator was used instead of a No.4 electric detonator, and 14.9 per cent when aN 0.8 electric detonator was used (see tabulation onp.45). The results of the tests emphasize the importance of using explosives in a fresh condition, but as fresh explosives can not always be had in mining work, strong detonators should be used in order to offset any deterioration of explosives from age.

Jan 1, 1913

By W. W. Adams

With production of coal per man-hour of work at a higher level than ever before, the coal-mining industry of the United States established a near-record in lowering the accident rate of nonfatal injuries per million man-hours of exposure in 1940, the injury rate being lower, except for 1939, than in any year since 1930, the first year for which comparable figures for nonfatal accidents were collected by the. Bureau of Mines, United States Department of the Interior. The rate for fatal accidents, on the other hand, was not as low or favorable as in 1939, nor was it as low as in many years since 1910, the earliest year for which fatality rates were complete for all coal-mining States. Accident and employment reports received from mine operators and fatal-accident reports from State mining departments and inspectors showed that 533,267 men were employed at coal mules in 1940, exclusive of the number employed at coke ovens, Although this number represented 6,108 fewer employees than in 1939, a large increase was made in the volume of work performed and in the quan¬tity of coal produced. In 1940 the amount of labor performed at coal mines was 748 million man-hours, a gain of more than 10 percent over the previous year. The average employee worked 199 days, an increase of 20 workdays per man. Production of coal was nearly 513 million tons, an increase of 14 percent, of which more than 461 million tons was bituminous coal and more than 51 million tons was Pennsylvania anthracite. Accidents to mine workers caused the death of 1,388 employees; in addition, 59,781 employees were injured, and each injury resulted in disability of the employee for more than the remainder of the day on which the accident occurred.

Jan 1, 1942

By Jay F. Colinet

Researchers at the Pittsburgh Research Laboratory (PRL) of the National Institute for Occupational Safety and Health (NIOSH) work to reduce respirable dust exposures in mining operations. One focus of this research is silica dust control for surface and underground operations in the metal/nonmetal mining industry. PRL researchers analyze dust sampling results from the Mine Safety and Health Administration (MSHA) to identify high-risk occupations to guide research efforts. Research is then conducted in an effort to improve existing technologies and/or develop new controls for reducing worker exposure to airborne silica dust. During the last few years, PRL researchers have conducted research related to the following goals: improving protection provided by enclosed cabs on mobile surface mining equipment, reducing dust generation from surface drills, reducing dust levels in iron ore operations, and developing a new method to clean dust from workers? soiled clothes. A description of each of these controls and subsequent dust reductions quantified through site surveys will be provided.

May 1, 2007

By Cristiano Devitte

O presente trabalho busca verificar a viabilidade técnica de utilização de aços com diferentes percentuais de elementos de liga em sua composição química para a fabricação de brocas DIN 338, com e sem revestimento PVD de TiN comparando com aço AISI M2. A caracterização do material foi realizada em conformidade com a norma SEP 1615 e a identificação do tamanho de grão foi realizada pelo método Snyder-Graff. No teste de furação foi utilizada um centro de usinagem vertical 3 eixos. A aderência do filme PVD foi verificada pelo teste de indentação VDI 3198. As variáveis significativas foram o material do substrato, o revestimento da ferramenta, a velocidade de corte e o avanço de corte. As variáveis de resposta analisadas foram o desgaste da ferramenta, o número de furos produzidos, a rugosidade superficial e o diâmetro dos furos. Ao final do trabalho foi possível constatar que o material Z2 ainda não pode ser utilizado como alternativa ao AISI M2 para a fabricação de brocas helicoidais de aço rápido.

Aug 7, 2018

By Robert D. Thomson

The plastics industry runs into the billions, both in the dollar value of its finished, products and in the pounds of plastic raw material produced. It is, too, one of the fastest growing industries with a 300 percent increase in production in the past ten years. Informed estimates set 5.9 billions pounds as the plastic volume for 1959. Statistically, this is equivalent to a per capita consumption of 25 pounds in the United States. Plastics are man-made materials in contrast to natural materials like wood and are a family of materials -- not a single material - each member having special advantages. A generally accepted definition; for plastics is; a large and varied group of materials which consist, wholly or in part, of combinations of carbon with oxygen, hydrogen, nitrogen, and other organic and inorganic elements. This, while solid in the finished state, at some stage in its manufacture is soft enough to be formed into various shapes, most usually through the application either singly or together of heat and pressure. Many combinations and many different materials are thus possible. Therefore, for purposes of simplification, most plastics can be classified under one of 14 recognized basic family groups. These groups in turn generally can be further classified into one of two major subdivisions - thermosetting or thermoplastics. A few plastics are in between and they can be formulated to be either thermosetting or thermoplastic.

Jan 1, 1960

By Gustavo Queiroz Esteves

O objetivo deste trabalho foi avaliar a utilização de peneiras de alta frequência em circuitos de beneficiamento mineral. Foram testadas diferentes aberturas de telas (mm), taxa de alimentação (t/h) e percentual de sólidos para verificar a eficiência global de peneiramento na fração 0.15mm. Frações retidas nesta malha têm sido apontadas como críticas para a flotação, sobretudo flotação em colunas. O circuito clássico das usinas normalmente utiliza ciclones para classificação de partículas finas (

Aug 1, 2018

The principal activities of the Bureau of Mines Explosives Research Center from July 1, 1962, to June 30, 1963, are described briefly in part 1. Part 2 gives short abstracts of publications that appeared during fiscal year 1963; in general, the research reported in these publications antedates the report period.

Jan 1, 1965

By R. L. Soderberg

This paper is one of a series on mining methods and costs being published by the Bureau of Mines. It describes briefly the mining methods employed since the start of operations in 1937, with emphasis on the diamond-drill blast-hole method of ore breaking and slusher-drift method of ore drawing at the Holden mine of the Howe Sound Co., Chelan Division, Holden, Wash. The Holden mine is in the north-central part of the Cascade Range, 11 miles up Railroad Creek from Lake Chelan. The nearest railroad is at Chelan Falls, 40 miles by boat and 4 miles by highway from the mine. All freight comes into the mine and all concentrates are shipped out via Chelan Falls. The altitude of the main haulage level is 3,500 feet. Railroad Creek Valley is covered with a dense growth of fir and spruce, while most of the surrounding mountains are rocky, with sparse timber growth.

Jun 1, 1948

By Ralph H. Espach

Wyoming contains many petroleum and natural-gas fields, and more than 250 geological structures have been mapped; however, only about 85 have been found (July 1938) to contain petroleum or natural gas, or both, in commercial quantities. To January 1938 approximately 434 million barrels of oil and 915 billion cubic feet of gas have been produced, and it was estimated that proved oil reserves in Wyoming amounted to 300 million barrels.' The Salt Creek field, the largest in the Rocky Mountain area, alone has produced 64 percent of the State's oil and 46 percent of its gas. This field ranked thirteenth among the producing fields of the United States in total cumulative production as of January 1, 1938. On this basis it ranks with the Kern River and Huntington Beach fields of California and the Butler County fields of Kansas. The Salt Creek field has declined in relative importance; in 1937, while still the largest oil-producing field in the State, it produced 31 percent of the oil and 11 percent of the gas extracted from all wells in Wyoming.

Jan 1, 1941

By Izabelle Lannes Salgueiro Ferreira

O presente trabalho teve como objetivo adequar às propriedades mecânicas dos perfis ASTM A572 G60, através do estudo da influência dos parâmetros de processo de laminação e composição química do aço. Os perfis ASTM A572 G60, são utilizados nas indústrias de fabricação de torres de transmissão. A metodologia utilizada neste trabalho foi o desenvolvimento de um modelamento matemático, com base na ferramenta estatística de Análise de Regressão Múltipla. Através desta ferramenta foi possível obter previsibilidade de processo e identificar os parâmetros mais influentes nas propriedades mecânicas dos perfis ASTM A572 G60, o que possibilitou a determinação da composição química ideal do aço e os melhores parâmetros de processo de laminação.

Jul 30, 2018