Search Documents

This is a most interesting paper and some data in it are corroborated by work I did at Watertown Arsenal some time ago with iron powder. I would like to ask Dr. Wulff to say just a little more about the compressive and tensile stresses on the surface of compacts. JOHN WULFF (author's reply).-Our work has not yet been completed; although enough data have been obtained with cylindrical compacts of iron to permit some conclusions. Briefly, in a compact 3/4 in. high and 1/2 in. in diameter pressed at 48 tons per sq. in., the residual stresses on the surface measured by X-ray diffraction techniques are as follows: The radial stresses on top center and bottom of compacts are practically zero; the longitudinal residual stresses on the side walls are near the top quarter of the compact about seven tenths that of the yield point of mild steel in tension; at the center surface of the compact they are in compression and in magnitude about 0.3 that of mild steel in tension; near the bottom, they are practically zero. F. V. LENEL.?- I was particularly interested in the work that Messrs. Wulff and Seelig reported on the influence of lubrication on the density of parts. In connection with the work of the American Society for Testing Materials on determining the green density of a compact, we ran into considerable difficulty in getting reproducible results of green density determinations. It was much easier to get a reproducible green density when the lubricant was mixed with the powder than when the lubricant was applied to the die walls; particularly when the die was not perfect-i.e., if it was somewhat rough or out of round. In this case, it was almost impossible to get reproducible green densities when the die walls were lubricated, while it was not too difficult to get reproducible

Jan 1, 1946

By J. C. Febles

HISTORY. THE use of iron for the precipitation of copper was known at least as early as the fifteenth century. Both Paracelsus and Basil Valentine refer to it in their writings, as early as 1500 A. D. It was used in Peru, for this purpose prior to 1637, and at Rio Tinto, Spain, as early as the sixteenth century. The statement has been made repeatedly that in the early history of the mining industry at Butte, the practicability of this method of recovering copper from solution was overlooked, and that enormous quantities of copper-bearing water were allowed to go to waste, the copper in which might easily have been recovered at small cost; and that this oversight on the part of the mine operators was due to ignorance of this method of recovering copper. As a matter of fact, very little copper-bearing mineral was encountered in the mines of Butte until a depth of 400 or 500 ft. bad been reached, and in many cases much greater depths were necessary to reach the copper-bearing zone. The water encountered in the upper levels (although in most cases quite highly mineralized) contained little or no copper, and it was only after considerable areas of copper-bearing ore had been uncovered and developed that copper sulphate began to. appear in the mine water in any considerable quantity. In fact, the first water that was observed to contain copper carried it in such small amounts as to be of little or no importance. It was only after years of underground work had opened extensive areas of stopes, drifts, and other underground workings, these being subsequently filled with waste, nearly all of which contained small copper values, which became oxidized by exposure to the air and were acted upon by the slowly percolating mineral water, that the recovery of copper from mine water became commercially important.

Jan 7, 1913

By W. T. Cardwell, R. L. Parsons

This paper discusses the practical problem of estimating a single equivalent permeability for an oil reservoir, or a portion thereof, whose actual permeability varies in an irregular manner. Limiting averages for general types of permeability variation are developed, and illustrated by examples involving important, specific types of variation. Introduction The theory of the flow of fluids through porous media1"4 is becoming increasingly important in predictions of oil-reservoir behavior. In practical applications, however, reservoirs are seldom found to which simple theory strictly applies. Actual reservoirs have complicated shapes and nonuniform permeabilities and porosities. This paper discusses the problem of estimating a single equivalent permeability for an oil reservoir, or a segment of an oil reservoir, whose actual permeability varies in an irregular manner. The equivalent permeability of a reservoir segment is defined as the permeability of a homogeneous segment of the same dimensions that would pass the same flux under the same pressure drop- It is the permeability value that can be used in simple theoretical formulas to calculate the reservoir behavior. To the authors' knowledge, previous theoretical calculationst on systems of nonuniform permeability have been carried out only by Muskat'"; and he has not dealt with irregular variations, except in writing down the general differential equation for the pressure in variably permeable systems.lb In practical work, many calculations necessarily have been made to estimate equivalent permeabilities from the permeabiiity profiles obtained by core analyses. Regarding such calculations, Johnston and Sherborne6 say: Simple arithmetic and weighted averages have been tried on many wells and it has been found that, where frequent sampling has occurred, the arithmetic average is as satis- factory as a weighted average. It is possible that the application of statistical methods to the analysis of permeability data as recently presented by Law8 may prove fruitful. L,, has made a valuable contribution in showing how statistical analyses may aid in picturing the characteristics of a reservoir from those of a necessarily limited number of core samples. It is believed however that the particular problem of the estimation of equivalent permeabilities can be most directly approached from a fluid dynamical viewpoint as given in the present paper. An example is presented of the use of the conclusions herein in conjunction with Law's method. Theory In order to approach the problem of heterogeneity simply, it is interesting to consider a square block composed of four smaller, homogeneous, square blocks of porous medium, two of which have a

Jan 1, 1945

By William B. Phillips

The concentration of natural magnetites has been carried on in this country for several years, and more or less information has been collected on the subject. Various inventors, availing themselves of the magnetism which is inherent in such ores, have devised machines for separating the impurities from the ore by means of the electric current; and a greater or less degree of success has rewarded their painstaking and persevering efforts. We are now fairly in position to judge of the value of the process as applied to such material. It is not my purpose to speak of this matter further than may be required by the emergencies of the case. I shall assume that most engineers and metallurgical chemists are already acquainted with what has been done at the Chateaugay mines, at Mineville, at the Benson mines, at the Weldon and Ogdensburgh mines, and at Cranberry; although, at this latter place, there has not been so much done as we could wish. I shall not now speak of the various types of separators. From the time of William Fullarton, to whom was granted an English patent, in 1792, for separating iron-ore by the application of magnetic attraction, down to the present time, a great. many devices have been suggested, and a great many patents taken out for this purpose; but it is not necessary now to enter upon a discussion of their merits. Perhaps, at some future meeting of the Institute, after we shall have experimented further with some of the machines on the market, there may be an opportunity to contribute something to the current knowledge of the efficiency and economy of separating-machines. In this paper I propose to give, as briefly as possible, the results already reached in converting a non-magnetic ore into magnetic ore, and then concentrating it over a magnetic separator of the alternate-polarity type. I am aware of the work

Jan 1, 1896

By M. A. Scheil, S. L. Hoyt

About three years ago eight standard steels were prepared for the cooperative investigation of methods for oxygen analysis, sponsored by the Iron and Steel Division of the American Institute of Mining and Metallurgical Engineers and by the National Bureau of Standards. A preliminary report of the results was made at the annual meeting of the A.I.M.E. in February, 1936. † This report showed the reliability of vacuum-fusion methods and further brought out certain advantages of the fractional vacuum-fusion method. The results obtained by the authors with the latter method will be discussed here, with some comments on the procedure for those who are interested in determinations of gases in steel. Some additional comments are offered on the use of the polarizing microscope for identifying the inclusions in the steel to check and amplify the findings of the fractional vacuum-fusion analysis. For details of the fractional method, see the paper by L. Reeve1. Degassing the Crucible One of the sources of error in vacuum-fusion methods has been the blank gases evolved from the graphite crucible after preliminary out-gassing. We have used 1750" C. as the outgassing temperature. This gives a base pressure at that temperature of less than 0.030 mm. after one hour and of 0.004 mm. on dropping the temperature to 1575" C. At lower extraction temperatures the base pressure is 0.001 mm. at 1050" C., 0.002 mm. at 1170" and 0.003 mm. at 1320' C. Because of the size of our induction coil we are limited to this temperature, although it 'would be advantageous to use 1950" to 2000" C. Hamilton2, after outgassing at 1850" C. for 100 min., was able to reach a base pressure of 0.001 mm. for a temperature of 1700' to 1725" C. This would give a blank corresponding to less than 0.00015 per cent 02 and 0.00005 per cent H2. Chipman and Marshall outgas at 2000" C. for one hour by using a special construction

Jan 1, 1937

By L. E. Mannion

Sodium carbonate (soda ash) is one of two principal commercial alkalis. Its principal competitor is sodium hydroxide. The use of sodium carbonate is recorded in ancient Egypt, where naturally occurring brines and solid salts provided impure soda for early glassmaking. Until the 19th century, soda ash (as well as potash) was recovered mainly by leaching wood or other plant ashes. In 18th-century Europe, for example, leaching seaweed ash with hot water produced a brown laundry lye. One of the better grades of this material was a Spanish product, barilla, which analyzed 24 to 30% Na2CO3 (Hou, 1942). The modern chemical industry was born in 1691 with the LeBlanc process for making sodium carbonate from salt, sulfuric acid, and lime. English industry used this process extensively in the 17th and 18th centuries. The next major advance was in 1863, when Ernst Solvay devised the ammonia-soda, or Solvay process. The first of many Solvay plants was built in 1874. These supplanted the LeBlanc method and dominated worldwide soda ash production until 1974, when mined sodium carbonate became predominant. Although considerably less important until recently, natural sodium carbonate deposits historically have supported small soda ash operations throughout the world. Shortages during World War II stimulated production of "natural" soda ash from such deposits, particularly at Searles Lake, CA and Lake Magadi, Kenya. More spectacularly, increased production from the vast trona deposits in Wyoming has virtually supplanted the Solvay process in the US. Principal producers of natural soda ash as well as the character of the source deposits are listed in Table 1. [ ]

Jan 1, 1983

By H. G. Doll

A new logging method, called induction logging, is described; it measures the conductivity, or resistivity, of the strata traversed by a bore hole. The apparatus, which is briefly described, comprises a coil system coupled with the ground by induction, so that there is no need for direct contact with the mud, or with the formations. For that reason, the method is particularly useful in oil base mud, and it was first applied to that case. A discussion concerning the respective contribution of each region of ground in the vicinity of the coil system is given. Through the concept of a geometrical factor, it is demonstrated that the total signal, which measures the apparent conductivity, is the summation of the partial products — geometrical factor by conductivity — for the different regions of the ground under consideration. It is thus possible to establish, for each type of coil arangement, investigation characteristic as well as departure curves and correction charts for beds of various thicknesses. This should greatly facilitate the quantative interpretation of the field logs, even in cases where such interpretation would have been difficult on electric logs taken with electrodes. It is also shown that focussing combinations of coils can be used, which give, directly on the recorded log, a value close to the true conductivity, even for fairly thin beds, thus eliminating in most cases the need for corrections. These focussing systems also give a sharper definition of the boundaries between successive strain.

Jan 1, 1949

The Jeffrey operation of Canadian Johns -Manville Co. , Ltd., at Asbestos, Quebec, is considered to be the world's largest asbestos mine. It accounts for approximately 37% of Canadian production of chysotile asbestos and about 13% of world production. Rated capacity is over 600,000 stpy (540,000 mtpy) of fiber, of which well over 90% is exported to the United States and seventy other countries. During the early 1970's the company completed a five-year modernization and expansion program which included the installation of a unique 72 in. by 93 in. gyratory crusher to handle the extremely blocky serpentinized peridotite ore. Because of the large diameter of this crusher the top ring of the shell was made in two halves which were bolted together. Hundred-ton trucks dump from two sides of the crusher into the 200 st (180 mt) dump pocket which is equipped with dust collecting ducts in the walls of the other two sides. The installation was designed to accommodate the eventual use of 200 -ton trucks. Crushed ore at a. size of 7 ½ in. (191 mm) falls into a uniquely designed crushed ore pocket equipped with three sloping steel sides and one vertical side, which make it totally live. Infrared heaters installed in back of the hopper sides prevent the ore from sticking to the steel. Another interesting feature is an eccentric removal bridge which is permanently mounted inside the crushed ore pocket. The two halves of the bridge are let down by electric winches to form a platform on which the eccentric cart travels and from where maintenance is done. Level indications in the crushed ore pocket are by radioactive indicators. Under the crushed ore pocket is a 72 in. by 28 ft (1.83 m by 8.5 m) apron feeder which operates at 7. 2 to 50 fpm (2. 3 to 15. 3 mpm). Crushed ore is discharged to a picking belt for tramp removal. A crossbelt magnetic separator is also mounted over this belt. Permanently mounted belt reels are also situated over the picking belt to facilitate the changing of this unit. A 60 in. (1. 52 m) wide takeaway belt then elevates the crushed ore to t.he surface facilities. Instead of discharging to a crushed ore stockpile, the takeaway conveyor delivers the ore to a 300-ton distribution bin. The ore is then screened and secondary crushed; and the plus ¾ in. (19 m) is "stored in a 3,000 ton bin while the minus ¾ in. is dried and then sent to storage. This system of directly screening primary crushed ore is similar to that used at both the Endako molybdenum and Gibraltar copper operations in British Columbia. While it would seem connecting processing equipment directly to a primary crusher would have an adverse effect on the crusher availability, the 94% of scheduled time this crusher

Jan 1, 1978

NEW- MEMBERS The following list comprises the names of those persons who became members during the period Feb. 10, 1917 to Mar. 10, 1917. ANDERSON, .LAWRENCE W., Min. Engr., Boston Mine, Utah Copper Co. Bingham, Utah. AUSTIN, JOHN W., Assayer, Magma Copper Co., P. 0. Box 101, Superior, Ariz. BARNARD, C. W., Treas. and Resident Mgr., Arizona Asbestos Assn., Globe, Ariz. BIERMAN, A. C : Geol., Producers Oil Co., Box 75, Houston, Tex. BOCHERT, W. C., Prof. of Mining, South Dakota State School of Mines, Rapid City, So. Dak. BROOKS, FLOYD R., Shift Boss, Mond Nickel Co., Ltd., Worthington, Ont., Can. BROWN, CECIL J., Draftsman &,Surveyor, Wallaroo SC Moonta Min. & Smelt. Co., Wallaroo, South Australia. BURRAGE, ALBERT C., Vice-Pres., Chile Copper Co., 85 Amos Bldg.; Boston, Mass. BURGESS, JOHN ALBERT Genl. Supt., United Eastern Min. Co., Oatman, Ariz. CARLOCK, JOHN BRUCE, Supt., O'Neall Oil Process Co., - 608 Haas Bldg., Los Angeles, Cal. CARPENTER, BYRON H., Min. Engr., . . Willoughby, Ohio.

Jan 4, 1917

By Cyril Smith

ALTHOUGH not of the same importance as electrical conductivity, the capacity for conducting heat is nevertheless a very important property of metals and alloys. A knowledge of thermal conductivity is of value in selecting alloys for many purposes and in the calculation of the efficiency of apparatus which is being designed. Unfortunately, the determination of thermal conductivity is extremely slow and tedious, consequently few data have been obtained. A further reason for the lack of information is that there has long been an impression that the thermal conductivity of an alloy is directly proportional to the electrical conductivity and that it can therefore be calculated from the latter. The Wiedemann-Franz-Lorenz law of constant ratio of the two conductivities holds with a considerable degree of precision for all the pure metals, but appreciable deviations occur in certain alloys-particularly those containing nickel-and it seems difficult to predict exactly what the ratio will be. Therefore direct determinations of thermal conductivity should be made whenever the results are, needed with any accuracy. This research is intended eventually to cover all the alloys of copper that are of commercial importance, including the binary alloys of copper with zinc, tin, aluminum, nickel, silicon, manganese, cadmium and phosphorus, and the ternary alloys copper-nickel-zinc, copper-nickel-silicon, copper-manganese-silicon, copper-zinc-tin, etc. Most of these alloys are customarily used in the wrought condition and therefore were tested in the form of annealed rods. A limited number of sand castings were also obtained and examined. This paper contains a complete review of all the previous work that has been done on copper alloys, and includes a detailed description of the apparatus and method of procedure used in the present research, together with the new results obtained on the copper-zinc series, which is the only one completed at the present time. Subsequent papers describing the other alloys will contain the experimental results and discussion only.

Jan 1, 1930

By W. M. Peirce, R. K. Waring

Zinc of high purity offers definite advantages in certain fields. A process by which zinc of 99.99 + per cent purity is produced by pyro-metallurgical methods is described in this paper. The process consists of a fractional distillation following the primary reduction; this fractional distillation employs the principles of rectification for the separation of lead and other high-boiling impurities and cadmium and other low-boiling impurities. Theoretical Considerations Involved in Production of High-purity Zinc by Distillation Fractional distillation, fractional condensation, and rectification are recognized methods of separating mixtures of liquids. In the field of organic liquids these methods are widely used but not commonly to effect as complete a separation of liquids as is done in the problem under consideration. Zinc boils at 905" C., cadmium at 778" C. and lead at about 1620" C. Zinc may contain from several hundredths of one per cent to over one per cent each of cadmium and lead, and the problem is to reduce these impurities to a few thousandths of one per cent. For lead and zinc, the spread in boiling points is substantial, 715° C., while for zinc and cadmium it is only 127" C. The basic limitation of any separation by distillation may be found from the relation between the equilibrium composition of the vapor and the liquid for all mixtures of the two substances involved. If a mixture of constant boiling point is found, or if a stable compound that vaporizes without dissociation occurs, there is a definite theoretical limit to the degree of separation that is possible when operating at atmospheric pressure with respect to that mixture. Otherwise, any degree of separation is theoretically possible. The equilibrium composition of vapor in contact with liquid mixtures of zinc and cadmiurn at the boiling point has been determined experi-

Jan 1, 1937

By Kenneth Cottingham

The number of wells completed in Ohio during I940 was about 20 per cent more than during the preceding year, the comparative totals being 1020 and 1228. Of the 1940 completions, 327 were oil wells, 491 gas wells, and 410 dry. The completions for the past five years, divided into oil wells, gas wells, and dry holes, are shown in Table 2. Wells drilled deeper and input wells in water-flood areas are not included in the tabulation. The annual production of oil has decreased steadily in Ohio from the maximum of 23,941,000 bbl. produced in 1896. Table 3 shows the quantities of oil produced in the last five years. In 1940, the total was 3,052,000 bbl., produced by about 25,500 wells. The number of wells and the approximate quantities by grades are shown in Table I. Table i ,—Tabulation by Grade Grade 1 2 Barrels __________________________________________________________________________________________ Pennsylvania ............. . 1,198,000 Lima.................... . 325,000 Corning................... 3,730 1,159,000 Lodi...................... T,040 350,000 Cleveland................. 30 1:1,000 Total................... 25,500 3,052,000 The prices paid for Ohio crude oil in 1940, together with dates of changes in posting, are shown in Table 4. The production of natural gas in 0hio has declined from a maximum of 79,510,032 M cu. ft. in I9I5 S to 36,469,000 M cu. ft. in 1939, the most recent year for which a figure is available. Consumption reached its peak in Ohio in the year 1916, when it was 169,480,01r M cu. ft., declining to 114,720,ooo M CU. ft. in 1939. The produc-tion and consumption of natural gas in Ohio for the past five years are shown in Table 5. TAble 2.—Completions in Ohio during Past Five Years Numbs of Wells Drilled during Year YearI, ] Oil Gas Dry Total 1936............. 263 570 324 1,157 1937............. 317 503 45I 1,271 1938............. 189 433 288 gro 1939............. I70 501 349 1,020 19391940............. 327 491 410 1,228 Total.......... 1,266 2,498 1,822 5,586 Table 6 shows the number of oil wells and the number of gas wells completed by sands during 1940, with the average initial production per well for each sand. Table 7 shows the total number of wells drilled—oil, gas and dry—by sands. Development during 1940 Szth-Trenton.—For several years, considerahle interest has been shown in a horizon lying some 500 to 700 ft. below the top of the Trenton, known to the driller in western Ohio as the "green sand," and in eastern Ohio as the St. Peter. In 1939, ten 'lgreen sand" tests were drilled, all in western Ohio and all dry- In 19401 eight wells were drilled to this horizon, one of which was a small oil well (one barrel) in Men county- Of the remaining seven—all of which were dry-—one in Franklin County, in central Ohio, was drilled to a depth of 2903 ft. .Another was in Medina

Jan 1, 1941

By Henry Schaefer

Solution by electric analogy of performance problems of reservoirs containing oil and gas has heretofore depended upon a process of successive approximations based on material-balance calculations, because of variation in fluid compressibility. By the addition or subtraction of electric condenser capacity, the analogy network can be adjusted automatically for changing compressibility due to evolution of gas in the reservoir. The addition of a condenser is accomplished by an electronic circuit, which is described; subtracting a condenser is done by merely opening the electrical circuit by means of a relay. Introduction V. Paschkis and H. D. Baker1 first developed in this country a method of applying the analogy of flow of electric current in noninductive circuits to solution of heat-flow problems and suggested its application for certain other problems, such as flow of fluids or mass transfer and chemical diffusion. Necessary details for applying the analogy to flow of fluids in porous media were developed by IV. A. Bruce;= he classified3 the types of analysis and predictions that can be made by the analogy in class I, when the reservoir contains oil but no gas for the period under consideration; in Class 2, when both oil and gas exist in the free state in the reservoir sometime during the period under consideration. Duplication of bottom-hole pressure history and predictions for class I reservoirs can be obtained directly by electric analogy. Until now, the solution of problems pertaining to reservoirs in class 2 was obtained by successive approximations along with material-balance calculations. The object of this paper is to present a method for simplifying the application of electric analogy to class 2 reservoirs, resulting in a solution of these problems as direct as is possible for class I reservoirs. This is accomplished by an electronic control circuit, which adjusts the analogy network for changing compressibilities of fluids contained in the reservoirs. Analogy Network In electrical phenomena the analogy to two-dimensional fluid flow in a porous media is that of current flow through an ideal conducting sheet. This sheet, perfectly insulated on both sides, has resistance and capacitance uniformly distributed throughout its area but is of negligible inductance. The need for having the surface boundaries perfectly insulated is that good correspondence may be had with a permeable fluid-conducting stratum bounded above and below by impermeable media. 111 actual application the ideal conducting sheet, which has distributed parameters, is replaced by a network having lumped values of resistance and capacitance—the resistances are series elements and the capacitances are shunt elements. The larger the number of lumped

Jan 1, 1947

E. E. THUM,* Salt Lake City, Utah (written discussion?).-While the present paper is confined exclusively to the microstructure of fusion welds, it may be of interest to draw attention to certain appearances existing in resistance welds such as spot or butt-welded joints produced by the Thomson process. For instance, a butt weld between two pieces of carbon tool steel (carbon about 0.90 per cent.) will show concentric ellipsoids of the various materials from pearlite to martensite. The surfaces of demarcation are quite well defined, the center of the ellipsoid being at the intersection of the axis of the piece and the plane of the weld. Often these unannealed welds show a troostitic center; evidently this core was not quenched as rapidly as the surrounding shell. Such specimens are beautiful samples for instruction purposes. An annealed butt weld of this kind will show a very well defined central ellipsoid of decarburized, materials. It is interesting to consider the reason why this change takes place. It must be understood that the heat is on the metal for a very short time, possibly 30 sec. It is therefore evident that the decarburization, or migration, of the carbon takes place with extreme rapidity. Since no blowholes are evident in a well-made butt weld, the deoxidizing air and the products of combustion must migrate with the highest speed; second, the carbon might migrate back into the stock; or, last, a large proportion of the pearlite may be extruded with the hot metal, which forms a fin at the plane of weld. Examining these possibilities in detail, it is not probable that such deep-seated decarburization, extending with maximum effect to the very center of a 2-in. round bar, is done by reaction with the oxygen of the air. This would postulate entrance of oxygen and egress of carbon oxides in large quantity without leaving behind traces in the form of oxides or

Jan 5, 1919

By C. G. Dunn

NUCLEI that are formed during the recrystallization of a grain following plastic deformation generally have orientations that differ from the original. This aspect of recrystallization may be described in terms of orientation changes. It was shown previously, in an investigation on recrystallization in silicon ferrite,1 that the observed orientation changes were highly improbable on a chance basis, and that some mechanism must be involved. Analysis showed that the data could be satisfactorily classified into the smaller of two subclassesf of the 36 third- order twin transformations. No attempt was made at that time to classify the data within the special class of 12 third-order twin transformations, although results did indicate a greater probability for some of them to occur. A classification of this type would be more valuable, of course, with more data on orientation changes per old deformed grain. The present work fulfills this condition to some degree and also extends the scope of the investigation to include the effects of original orientation and the amount of plastic deformation. The effect of original orientation is of considerable interest because of the known effects of orientation on plastic deformation, particularly with regard to degree of fragmentation and the formation of de- formation bands, and because the orientations produced by deformation should influence the orientations obtained through recrystallization. Barrett and Levenson2 reported that single crystals of iron deformed in the range 82 to 97 per cent could be put into three general classes; namely, crystals in class I maintained a reasonably sharp single orientation, those in class 2 transformed into two distinct orientations, and those in class 3 changed into a large number of major and minor orientations. Something similar would be expected for silicon ferrite crystals, and verification of this for a few cases of types class I and class 2 deformation has been reported elsewhere3 for single crystals of silicon ferrite cold-rolled in the range 10 to 20 per cent. As an example of class 2 deformation, it was shown that a crystal of silicon ferrite cold-rolled in a {110} plane in a < 100> direction developed two layers, or deformation bands differing in orientation. When this happens it is possible to etch away one band and leave a single structure for use in studying the orientation changes that occur during recrystallization. when preferred crystal orientations are obtained in recrystallization, it is notparticularly necessary to evaluate groups of common orientation, as was done previously (ref. I, Table 6); but an

Jan 1, 1946

By Lloyd R. Jackson

IN the past 15 years there has been a great deal of interest in the fundamentals of plastic flow and rupture in metals and a number of papers have presented substantial advances toward a fundamental insight into the mechanism of these two processes. This paper is an appraisal of the present position with respect to the following: I. The relative importance of shear and hydrostatic stresses in controlling the plastic flow of metals. 2. The relative importance of shear and hydrostatic stresses in determining the amount of flow before rupture in metals. 3. The use of generalid strains in determining the effect of plastic flow on the work-hardening of metals. FUNDAMENTALS INVOLVED IN PLASTIC FLOW In attempting to devise a quantitative description of plastic flow in metals, it has been customary to assume that metals are homogeneous and isotropic. The fact that neither of these assumptions is correct complicates the experimental appraisal of relations developed. Never- the less, as will be shown, metals are close enough to being isotropic and homogeneous so that considerable insight into the mechanism of plastic flow can be obtained. The assumptions of .isotropy and homogeneity allow both the elastic and plastic behavior of metals to be described in terms of 12 variables-six being stress variables, and six being strain variables. ) From this viewpoint, it should be possible to represent the stress-strain relations in the plastic range for metals by a surface in 12 dimensions. One boundary of this surface would be the surface of transition from elastic to plastic behavior; the other would be the surface of rupture. These two surfaces would be joined by the surface of plastic flow. The shape of this composite surface would depend on the test temperature and speed of straining. This paper is concerned only with results obtained at constant temperature and constant speed of straining. While such a representation is conceivable, the demonstration of such a surface would present almost insurmountable obstacles. The most fruitful simplification of this concept has been the recognition that the behavior of metals in the plastic region is primarily a result of shear stresses and strains. Based on this viewpoint, it is possible to utilize stress and strain invariants that are independent of hydrostatic components to define an effective stress and strain. In effect, this amounts to reducing the task of representing stresses and strains in 12 dimensions to one of representation in two dimensions. The two invariants (one for stresses . and one for strains) that have received most attention are the following: [ ]

Jan 1, 1946

By J. D. Wright

INTRODUCTION The Endako deposit was first explored in 1926, but development waited until the early nineteen sixties. It first came under the control of Placer Development in 1963, and early in 1964 a decision to bring it into production was reached. The deposit is located near the geographic center of British Columbia, and is served by an east-west communication system including a paved highway, mainline railway and good telephone, teletype, and computer facilities. The plant area is shown in Figure 1. The operation is known as the Endako Mines Division of Canex Placer Limited of Vancouver. First production was achieved in June, 1965, at a nominal rate of 10,000 tons per day, but it soon was closer to 15,000 tons per day. In 1967, two new grinding and flotation, sections brought capacity to the present rate of approximately 27,000 tons per day. With mill heads of around 0.15 percent MoS2, production is about 14,000,000 pounds of molybdenum per year. A flowsheet of the operation is given in Figure 2. A legend for this flowsheet is given in Table 1. Published ore reserves are estimated at 214,500,000 tons at an average grade of 0.143 percent MoS2. PRIMARY CRUSHING The 85 or 100-ton haulage trucks dump over a grizzly into a 42 inch x 65 inch C.A.C. (Canadian Allis Chalmers) gyratory crusher. The

Jan 1, 1976

By Otto Wartenweiler

AFTER the phenomenal development of the new mine, the United Eastern Mining Co., with Mr. Frank A. Keith as President, decided to install a reduction plant. The character of the ore, closely resembling the product of other mines in the district, did not offer any particular metallurgical problems, since these neighboring mines had been operating milling plants very successfully for several years. Thus, with the general metallurgical treatment fairly well-defined, the matter of next importance was to design and construct a plant as economically as possible, that would give the best results obtainable. The ore consists of a mixture of calcite and quartz in about equal quantities with some decomposed andesite, while the average value of mill heads were calculated to be $20 plus in gold, no silver being present. The tonnage to be treated at ,the start was fixed at 200 tons, but, in view of the favorable condition of the mine, it was considered advisable to arrange facilities, for increasing the capacity to 400 tons. . While it is best in some cases to adopt a distinct independent unit system where future enlargement is contemplated, in this instance the plans worked out differently. Summarized, the treatment adopted consists of coarse crushing, coarse grinding, fine grinding and cyanidation. For coarse crushing the selection of the No. 6 size gyratory crusher was governed not so much by its capacity as by the size of the feed openings to properly receive the run-of-mine material, which was too coarse for a No. 5 crusher. To accomplish the coarse grinding to. best advantage, a careful comparison was made between the modern steel ball mill-the last word in crushing and grinding-and one of its older, and, at that time better-established, competitors, the rolls.&apos; The following conclusion was reached: While it is possible that for the sized plant under consideration the cost of operating rolls might be a little cheaper, it is preferable to use ball mills because a simpler arrangement is possible, and1 because. the handling of, ball mills is preferred by the operator.

Jan 11, 1917

By W. P. Sykes

SINCE Honda and Murakami1 in 1918 proposed their constitutional diagram of the carbon-free iron-tungsten system, considerable effort has been expended by several investigators in attempts to define more positively the structural features of the alloys. The existence of an intermediate phase corresponding to the formula Fe3W2 (68.7 per cent W) was proposed from evidence of a purely metallographic nature by one of the present authors2 in 1926. Since that time the identity of this phase has been confirmed by Arnfelt3 and by Takeda,4 both of whom employed X-ray methods as well as the microscope and the chemical analysis of isolated microconstituents. According to Arnfelt, Fe3W2, as crystallized from the iron-rich melts at a temperature above 1450&apos;C., contains by analysis 68.7 per cent W. The lattice of this phase is characterized by trigonal symmetry. Arnfelt, moreover, proposed a second intermediate phase formed at some temperature between 1450° and 1000° C. by a peritectoid reaction involving Fe3W2 and the iron-rich solid solution. A melt containing 25 per cent W was cooled to 1000° C. and heated for. 100 hr. The precipitated tungsten-rich constituent was separated and found by analysis to contain 62.6 per cent W. This composition agrees closely with that represented by the formula Fe2W (62.2 per cent W). Diffraction patterns from the concentrated precipitate showed a hexagonal unit cell. Takeda confirmed the data of Arnfelt regarding Fe3W2 but was unable to detect Arnfelt&apos;s second intermediate phase. While Takeda. failed to describe in detail the treatments employed, he stated that in alloys containing 40 per cent W which were quenched after heating at various temperatures between 1200° and 1450° C., no evidence of the second phase (Fe2W) was observed either in the microstructure or in the diffraction patterns of isolated residues. He therefore considered the existence of this low-temperature hexagonal compound as disproved.

Jan 1, 1932

R. L. Fleischer (Department of Metallurgy, Massachusetts Institute of Technology)— The authors have presented valuable observations of oehavior of aluminum at intermediate and high temperatures. I should like to consider their interpretation of the appearance of cross slip plane traces in sample B-3 as partly due to "bending of the crystal due to grip constraint." Because bending moments might be set

Jan 1, 1960