Search Documents

By H. S. Martin

Although it was known some years ago at the Utah Copper Co. mills that fine grinding improved flotation recoveries, no accurate data were available until recently as to just how far the grinding could be carried economically. In 1923 the ultimate degree of fineness for flotation feed was supposed to be about 10 per cent. on 65 mesh, with approximately 55 per cent. through 200 mesh, which meant that most of the mineral would pass 100 mesh. At this time Garfield and Wilfley tables were used ahead of flotation and a good deal of the coarse mineral removed prior to the ball mill regrind. Shortly afterwards, mill-scale tests developed the fact that on a feed containing not over 10 per cent. +65-mesh material flotation alone would give a copper recovery equal to that obtained by the combination of tables and flotation, but that on much coarser feed the recovery with flotation alone was lowered. This was at a time when all the sulfide minerals were floated if possible, so that the only requisite was to grind fine enough to free the mineral from gangue. Earliest Use of Microscopic Examination of Tailings As early as 1921, the writer had attempted to determine by chemical analysis the relative proportions of copper minerals in tailings from an ore that made extremely poor flotation results. Chemical analysis was not satisfactory or conclusive, and samples of these tailings were sent to the U. S. Bureau of Mines Station at the University of Utah for microscopic examination. The question at that time was to determine, if possible, which copper minerals had been lost and why, but R. E. Head, in his report, revealed other interesting data. He said in part: Briefly stated, the mineral partieles or grains may be classified into scparate groups as follows: 1. Free grains of pyrite, chalcopyrite, chalcocite and bornite, respectively, which contain 110 other included sulfides; 2. Grains in which all three of the copper sulfides are representel (the core may be of chalcopyrite, partially altered to boruite, these two minerals being cntirely surrounded by a shell of chalcocite); 3. Grains composed of equal amounts of bornite and chalcocite or chalcopyrite and chalcocite. The grains of free mineral particles are perhaps the most numerous, taking the ore as a whole, but it is noticeable that of the grains of combined or associated sulfides

Jan 1, 1930

By Donald D. Smythe

This paper describes briefly the topography and geology of the region where the mica-bearing pegmatites are found and discusses prospecting, the quality of the mica, its preparation, and evaluation of the deposits. Muscovite mica occurs in a number of widely separated localities in Brazil, but production has come largely from deposits in the southeastern and eastern part of the State of Minas Gerais (Fig. I). There the deposits form a discontinuous zone, which starts at a point go km. north of the city of Rio de Janeiro and extends north for some 500 km., roughly parallel to the coast. A maximum width of 180 km. is reached along the Rio Doce. To the west in Minas Gerais, and extending east into the states of Espirito Santo and Rio de Janeiro, the mica zone proper is fringed by areas in which there are scattered occurrences of mica-bearing pegmatites. A few of these outlying deposits have produced commercial mica, but most of them are unimportant. To the southwest, in the State of Sao Paulo, there are a number of mines, which at one time produced a very considerable amount of sheet mica, largely as a byproduct of kaolin mining. These deposits, and a few others lying between them and the main productive areas to the northeast, appear to be the southwestern continuation of the strong Minas Gerais mica zone. In the vicinity of Conquista, just north of the Minas Gerais boundary in the State of Bahia, and still farther north, near Jacobina, there are several known mica deposits. Their location indicates that they may be the northern continuation of the main mica zone. The major part of Brazilian mica production has come from four areas within the mica zone proper; from north to south, Governador Valadares, Raul Soares, Espera Feliz, and Muriaé.. The first is go km. from north to south and reaches a maximum width of 180 km. The Raul Soares area extends 135 km. from northeast to southwest, and in places is 80 km. wide. The Espera Feliz area is 100 km. from north to south, and reaches a width of 35 km. The Muriai. area extends 150 km. from northeast to southwest and its width reaches 40 kilometers. Between the known productive areas, and in the areas directly to the southwest and to the north of them, little mica has been produced. These gaps, as well as certain irregularities in the outline of the mica zone itself, are to be ascribed either to lack of prospecting or to conditions preventing the discovery of mica, rather than to its nonexistence. Elsewhere in Brazil mica has been reported from eastern Goiaz, Ceará, Pernambuco, Rio Grande do Sul, Matto Grosso, and Amazonas. Production from these sources is negligible at present. Because of the inferior quality of the mica from the more accessible of these localities, and the operational difficulties occasioned by the remoteness of others, it is improbable that they will become important producers for some time to come.

Jan 1, 1948

By G. Pizzi, G. M. Ciucci, G. L. Chierici

The use of the material balance equation to estimate the volume of hydrocarbons originally present in a reservoir, whose producing mechanism is partly due to water drive, has been discussed in the literature by several authors. There is no general agreement upon the possibility of obtaining reliable results by this method. Gas reservoirs in contact with an active aquifer are considered in this paper. Theoretical considerations based on the cybernetic principle of uncertainty (which states that the internal structure of a system cannot be uniquely determined from its observed external behavior) lead to the conclusion that the volume of gas originally present in a reservoir of this type cannot be uniquely determined from its past history. The range of values which encompasses the actual value of the reserves varies from case to case and must be determined by either numerical or analogical methods. Results obtained for six gas fields are reported. All these fields were produced with small fluctuations in their production rates, as is common practice for gas reservoirs; no gas storage fields were considered. Results obtained show that reserves values in a range of 1 to 2, associated with appropriate aquifers, allow the matching of the reservoir past history with mean-square deviations less than the experimental errors involved in pressure and produclion measurements. Similar results have been found in several other partial water drive gas reservoirs. From these results it is concluded that gas reserves cannot be uniquely determined from the past performance of partial water drive reservoirs, at least in cases where the reservoir has been submitted to small fluctuations in the production rates, and pressure data of normal accuracy are available. INTRODUCTION A number of authors have analyzed the problem of estimating the reserves originally present in a partial water drive reservoir from its past pressure-production performance. Literature which deals with this subject can be grouped, according to their conclusions, as follows. 1. A reliable value for the reserves can be obtained even if reservoir data (pressure and cumulative production) are affected by errors within the normal range.'-' 2. A reliable value for the reserves can be obtained only if reservoir data are very accurate'- or if past production performance has been subjected to abrupt variations in the production rate."' 3. No unique value for the reserves can be obtained from reservoir past production performance. This conclusion has been based upon theoretical considerations" and verified in several field cases. The purpose of this paper, which deals only with partial water drive gas reservoirs, is to test the above conclusions against actual field cases. Some theoretical considerations on this problem are also presented. THEORETICAL CONSIDERATIONS As the behavior of a gas reservoir communicating with an aquifer depends on both the aquifer and the reservoir characteristics, the physical system to be studied is the combined gas reservoir plus aquifer. The information which is available for studying the performance of such a system is the well production rates and bottom-hole pressures, all given as functions of time. The external behavior of the reservoir-aquifer system is therefore described by 2n input variables (Gp, Wp,) and n output variables (p,), n being the number of wells in the reservoir. In reservoir engineering it is common practice to consider the reservoir as a whole, disregarding the internal distribution of pressures and of producing wells. This practice is equivalent to substituting the above multi-variable system with a single-variable system, where the average reservoir pressure is the only output variable and the cumulative production G,(t) and W,(t) are the input variables. The internal structure of such a system, defined by initial gas reserves G, aquifer shape and dimensions, boundary conditions and petrophysical parameters distribution throughout the aquifer, is unknown. Therefore, from a cybernetic point of view the system is a "black-box It has been demonstrated" that for a blackbox the indetermination principle holds. Accordingly, the number of different internal structures (or set of parameters) which can account for the observed external behavior is infinite. As a consequence, the initial reserves cannot be uniquely determined from the reservoir past performance. When W,(t) is known, the determination of G from

By Maurice Ewing

THE purpose of this paper is to present the results of the application of the earth-resistivity method of subsurface investigation to the problem of locating seams of anthracite coal beneath a mantle of soil and subsoil. Details are given of the successful use of this method in locating the outcrops of anthracite seams in actual prospecting. The presence of the outcrop of an anthracite seam is indicated at points where electrical resistivity tests showed relatively low readings. The reason for, this is that in some localities the resistivity of anthracite was found to be about 0.0001 megohm-cm. compared to 1 to 200 megohm-cm. for shales and sandstones. For two reasons it is believed that the data sum-marized in this paper should be of particular interest. In the first place, most of the interpretations of the resistivity survey have been checked by subsequent drilling and some by the removal of the overburden and the exposing of the anthracite seams. It is infrequent that the oppor-tunity for checking results so thoroughly is given. In the second place, the fact that recent commentators 1.2.1 on the application of geophysical methods to mining have concluded that direct prospecting for anthracite and other types of coal is not promising makes the good results obtained more significant. So far as the authors can learn, the only previous experiment with electrical methods in the Pennsylvania anthracite field was one made by Sherwin F. Kelly in 1922, when he used the self-potential method at Wilkes-Barre4. The profile he made does not show a very marked correlation with the geologic cross section. Kelly points out that stray currents from electric motors in the mines undoubtedly affected his results, but the experience of the present authors with stray currents from mining machinery suggests the possibility that the potentials measured by Kelly were due almost entirely to this effect.

Jan 1, 1936

By D. L. Harris

Chemical upgrading testwork on Stillwater chomite concentrate shows that reduction roasting and leaching (sulfuric acid and/or ferric sulfate) can provide upgraded feed to ferrochromium furnaces for making upgraded ferrochromium. Two-stage reduction smelting in electric arc furnaces can make upgraded ferrochromium also. Sulfating roasts and leaching (acid and/or water) results using gaseous SO2—SO3 or solid ammonium sulfate were not satisfactory for upgrading chromite. Chemical upgrading of domestic Stillwater (Montana) chromite has been considered at various times1'2' to provide a material with higher chromium to iron ratio, more like foreign high grade ore, for the production of standard grade ferrochromium. Physical bene-ficiation of Stillwater chromite ore can provide a ratio, Cr/Fe, no higher than the ratio in the chromite mineral, which is approximately 1.7. For comparison the analyses of a foreign metallurgical grade chromite ore, a high grade electrostatic process Stillwater concentrate and a stockpile concentrate from the Stillwater ore are noted in Table I. Single stage smelting of the high grade foreign ore with a ratio, Cr/Fe, of 3.37 can provide a ferrochromium of over 65 pct chromium content. Similar smelting of the Stillwater concentrate with a ratio of 1.7 can provide a ferrochromium of 50 to 55 pct chromium content.' It has been demonstrated on a pilot plant scale that chemically upgraded Stillwater chromite having a ratio, Cr/Fe, of 3.0 also can be smelted to provide a ferrochromium containing over 65 pct chromium.5 Two major considerations for an upgrading process are the ratio, Cr/Fe, in the product and the chromium recovery. A minimum ratio, Cr/Fe, of 3.0 is required in the product but for economic reasons a higher ratio is desirable for blending purposes as long as the recovery is satisfactory. Data from different kinds of chemical upgrading testwork are presented in this report. Some of the testwork was conducted to make a product which was not intended to be feed for ferrochrome smelting, but the data are considered pertinent to chemical upgrading. Results reported by others are noted also for comparison. WORK REPORTED BY OTHERS The U. S. Bureau of Mines has contributed much to the literature on chemical upgrading of chromite and a summary is given in Table 11. Reduction roasting and acid leaching were reported by Boericke and Bangert,1 by Lloyd and Gorst, et a1,2 and by Boericke3 to demonstrate very good success on a laboratory scale and only fair success in pilot plant tests for Stillwater (Benbow) concentrates. This work included basic studies on thermodynamic properties to explain the reduction and leaching results. Canadian workers, Downes and Morgan,9 have reported experimental success in upgrading a low grade Bird River chromite, similar to Stillwater material by the same process. Russian workers1' have noted results on reduction tests of high grade chromite which may apply to low grade ores and which help in understanding the reduction process. The use of flux additives in the reduction process was an innovation of their work. The Canadian workers9 also reported other kinds of experiments, including autoclave leaching of the chromite in a limited amount of sulfuric acid. An insoluble basic chromium sulfate was formed and separated from soluble iron, magnesium, and aluminum sulfates to provide an upgraded material. U.S. Bureau of Mines workers, Lloyd, Rosenbzum, Home and Davis,' reported on autoclave leaching of Benbow concentrates as a means of obtaining chromium alum for electrolysis. This last work required selective crystallization of alum to separate iron from chromium. Chloridizing roasting of Benbow and Mouat concentrates has been reported by Hunter and Banning6 and others8 to show that the iron chloride could be volatilized from the chromite to provide upgraded residues.

Jan 1, 1964

By R. Hadfield

Last year this institute was good enough to accept some remarks by the writer regarding sound steel, entitle Plant for Hadfield Method of Producing Sound Steel Ingots…

Jan 1, 1915

By Robert Henderson

SEVERAL very interesting articles have been written on the caving system of mining, but most of these papers have dealt separately with the slusher system or the chute and grizzly system. In this paper, a comparison will be made of the two methods, both of which are being used at the Climax mine. The mine is on the Continental Divide, in central Colorado, at an altitude of approximately 11,500 ft. above sea level. The long, cold winters, characteristic of the high Rockies, create a number of operating problems not usually found in other mining areas. THE ORE BODY The Climax ore body is just east of the Mosquito fault. This structural deformation has brought the granite on the east against the sedimentary rocks on the west. The ore occurs in an intensely altered granite and schist around a silicified granite core. The ore is in a highly fractured zone of moderate silicification. The principal mineral, molybdenite, is found in these fractures. Barren dikes of granite porphyry cut through the ore body and core with no apparent regularity. The grade of the ore is fairly uniform and gradually decreases toward the footwall core and also into the hanging-wall granite. The footwall and hanging wall are determined entirely by assays. The ore body is roughly dome-shaped, with the apex truncated at the surface. It is covered to varying depths with talus. A horizontal section of the ore body on the Phillipson level appears as an annular ellipse surrounding the footwall core. The ring of ore varies in width from 300 ft. to as much as 800 ft. The north-south axis of the core is about 1200 ft. and the east-west axis is about 1800 ft. In the ore zone, the rock is sufficiently strong to maintain reasonably large openings, and openings larger than haulage drifts usually have to be supported. The ore is cut by a great many fractures and shears and breaks into rather large blocks when caved, necessitating considerable secondary blasting. The waste that overlies the ore body breaks relatively fine in comparison with the size of the blocks of the caved ore and tends to run through the broken ore in the cave, causing dilution unless the draw is carefully controlled. MINING SYSTEMS For several years the ore was mined by the chute and grizzly system, a system that differs from that used in other caving mines only in the size of openings and equipment. In the chute and grizzly system, main haulage laterals were driven along the footwall core and also along the

Jan 1, 1944

By J. A. Fellows, Earnshaw Cook, H. S. Avery

THE increased use of heat-resistant alloys (26 per cent Cr, 12 per cent Ni; 16 per cent Cr, 35 per cent Ni; 12 per cent Cr, 60 per cent Ni; etc.) in recent years has been accompanied by continued demands by the consumer for improvement in properties. The manufacturers of these materials, of necessity, have resorted to more critical studies of the basic causes of variations in fundamental properties. To keep pace with the need for augmented information, previous techniques of investigation have been refined and new test methods and instruments created. It is the purpose of this paper to describe the apparatus, experimental technique and precision of measurement that were employed in the exploration of properties of heat-resistant alloy presented in a companion paper.? The detailed precautions in experimental procedure essential for attainment of accurate and comparable data at elevated temperatures cannot be too highly emphasized. THE CREEP TEST Since the fundamental concepts of creep testing have been recognized for the past 20 years, present interest is restricted to refinements in equipment and experimental procedure. The creep-test laboratory constructed for the American Brake Shoe and Foundry Co. is designed to permit 1000-hr. tests in the temperature range of 1200° to 2200°F. with a choice of applied stress extending from 50 to 50,000 lb. per sq. in. in increments of 50 lb. per sq. in. To simplify the calculation of weight combinations, the loading beams (Fig. I) are provided with counterweights to eliminate the tare. The precision of the knife-edges (10.1 ratio) is such that a 10-gram weight placed on the upper specimen grip will be exactly balanced by a 1-gram weight attached to the loading shackle. Check of the loading weights proved the maximum error to be 0.06 per cent. Axial alignment is provided by crossed knife-edges in the grip seats. The furnaces are similar in design to those of Crane and Company, Battelle Memorial Institute, and the U.S. Steel Corporation. An 80 per cent Pt, 20 per cent Rh No. 19 B. and S. gauge wire is used as the heating element. The details of construction are shown in the radiograph reproduced in Fig. 2. The windings are held in place on an alundum tube with alundum cement; the distribution of turns is adjusted to give a maximum temperature gradient of ± 1°F. over a 4-in. gauge length (Fig. 3). To avoid sharp temperature differentials at the ends of the test section, the length of the furnace is four times the gauge length. Sixteen-inch coupons are used to reduce the temperature of the threaded

Jan 1, 1942

By S. B. Casey

[ ] IN 1880, an electric arc was struck over metal for the first time to experiment with controllable melting. The glare of this arc has reflected on the stacks of the steel industry and continued to light the path of steelmakers in their never ending quest -for faster, more economical, and better ways of producing steel. William Siemens is credited with first employing the electric arc to melt metal in a closed hearth and produce basic metallurgical reactions. By the turn of the century, an Italian, named Stassano, was experimenting with ore reduction by the electric arc. In 1899, Dr. Paul Heroult, in France, used the direct arc principle for producing ferro-chromium. His experiments quickly led him to develop a dosed-top arc furnace for the production of steel, and his first commercial shipment was recorded in December, 1900. American steelmakers, quick to sense the possibilities of this method of melting, invited Heroult to our shores, where, in 1905, he was responsible for installing the first arc furnace on the North American continent. This furnace, at Sault Ste. Marie, was built for ore reduction. But Charles Holcomb, founder of Holcomb Steel. Co. of Syracuse, N. Y. contacted Heroult in 1905 and contracted for the first American direct-arc electric furnace for steelmaking. On April 5, 1906, the first heat was tapped from this 3-ton unit. The furnace was basic lined and powered by a single-phase, 500 kw generator, -producing high amperage at low voltage. It is interesting to note that, although the first few heats were made with cold charges, subsequent heats were duplexed. R. H. Bully, first superintendent of Holcomb Steel, persuaded the directors to purchase the unit to effect a more economical and efficient means of making tool steel by duplexing prime melting in a combustion fired furnace, and transfer of hot metal to the arc furnace for temperature adjusting, refining, and adding carbon and alloying elements. Today, duplexing is foreseen by some as the steelmaking process of the future. The promise shown by America's first arc furnace for ingot production quickly led to the purchase of a similar unit by The Firth Sterling Steel Co., in 1909, and to the purchase of the first arc furnace for production of steel castings, by the Treadwell Engineering Co., in 1911. From its humble start in 1906, production of arc furnace steel has never ceased to increase its yearly percentage of total steel production in the U. S., although certain other methods have declined or almost disappeared. By its ability to be used intermittently, the arc furnace gained favor and enhanced its reputation during depression days. When the attack on Pearl Harbor plunged us headlong into the long days of World War II, the arc furnace stood ready, flexible enough to be overburdened hearth wise 30 pct and power wise 25 pct, pouring its endless flood of alloy for the guns, tanks, ships, and planes which ultimately brought victory. During the post war boom, the now, proven virtues of low initial cost, faster installation, better yield, improved availability, and lower operating cost, enabled industry-particularly the small, new, independent producers-to locate strategically and profitably to meet the demand of an America that had been starved for new homes, appliances, cars, and highways. In the Korean police action, the arc furnace again proved itself by providing the latest alloys metallurgists could develop to meet the demands that the jet age and the innovations of guided missiles required. In today's peacetime prosperity, the arc furnace is continuing to provide the economic flexibility required to meet an ever increasing demand for better steel in the face of mounting costs, scrap shortages, and pressure toward decentralized location of industry.

Jan 1, 1961

By Arthur Taggart

THE major portion of the work described in this paper was performed by R. W. Young,+ a graduate student in the department of Mining and Metallurgy, Sheffield Scientific School, Yale University, working under a cooperative agreement between the Hardinge Conical Mill Co., the Sheffield Scientific School, and himself. Since this cooperative scheme is at present in effect in the case of a considerable number of other students in the department and since it is the hope of the school that the privilege thus extended may be utilized even more freely in the future by mining and manufacturing companies, it may not be amiss at this point to give a summary of the general plan. Briefly it is as follows: A graduate student, whose undergraduate work in this or other universities shows promise of ability to handle research work, is chosen by conference between the company and instructor involved. The aim of the company in the agreement then entered into is to obtain the solution of one or more of the technical problems with which it may be confronted, or, at the end of 1 or 2 years, to obtain as an employee a man especially trained in its work. As. a means to accomplish one or both of these ends, the company furnishes the machine, apparatus, or material to be tested and pays the student during his graduate work a small salary, usually just sufficient to cover his living expenses, tuition and fees. The aim of the student is special training along a line in which he is particularly interested, the attainment of his advanced degree, and the chance to show to his future employer ability to handle such problems as may be presented to him. In return for the financial aid which he receives he agrees to devote at least half of his working time to the special problem submitted by his company. The other half is devoted to study of the collateral subjects required by the department for the granting of the degree which the student seeks. The student further agrees to enter the employ of the company in question at a wage not greater than that paid in like positions to recent graduates not specially trained and to remain with his employer at such wage for at least 1 year. If the student is to obtain a degree, the special work forming the basis of his investigation must be such as will involve real research and not mere routine manipulation. The subject is chosen by conference between the three parties to the agreement. The work is carried on under the direct supervision of the instructor involved. The school furnishes the general laboratory and library equipment essential to the pursuit of any extended investigation, In

Jan 4, 1917

By John S. Johnson

THE purpose of this article is to describe several types of borehole lining in common use, and especially to offer a relatively new means of reducing the expense of maintaining boreholes where they are subjected to corrosive action of water flowing either inside or outside of their casing. In the Anthracite region of Pennsylvania, boreholes are used for many purposes, the principal ones being: openings between the surface and underground workings through which are passed steam, water and compressed-air lines, ropeways from surface hoists to underground rope haulages, conduits for electric power and signal lines, water-discharge lines from underground pumping stations, and inlets to mine workings for flushing material. LININGS FOR BOREHOLES The inadequacy of steel pipe for use in boreholes has long been recognized. Various substitute materials have been tried, including screw-joint cast-iron pipe (Fig. I). Cast-iron pipe, while very effective as a discharge line for acid water (mine water) being pumped to the surface, is not so effective when serving as a conduit for silt and crushed rock being flushed underground for filling mine voids. Terra cotta pipe (Fig. 2) has been used in boreholes, and lasts a long time if the glazed inner surface of the pipe remains intact. Its installation in a borehole is very difficult and is recommended only where it is certain that there will be no subsidence of the surrounding territory. Accessibility in order properly to join each section of the pipe is essential to a satisfactory job. In large water holes, where it is possible to lower a man into the hole for sealing the joints of the pipe, glazed terra cotta pipe has been used successfully for delivering mine water from pumps in the mines. For large holes used for flushing refuse into mine workings where the surface wash is shallow, standard paving brick have been used to form a tube through the wash to the bedrock. These brick are laid radially, backed by common brick and cobbles laid in cement. It is obvious that the shaft through the wash must be large enough to permit a man to work in it. The flushing material is carried through bare rock from the juncture at bedrock to the openings underground. This plan has been used, particularly where a cast-iron surface line is laid upon the surface to carry the flushing material from the breaker to the hole, and down the hole continuously, with no opening to the air at the top of the hole, thereby eliminating the necessity of an attendant at this point (Fig. 3). Another similar type of borehole lining is constructed of hexagonal pieces of vitrified brick (Fig. 4). This type requires a steel drive pipe through the surface wash large enough to provide a finished tube of the desired size surrounded by a brick wall about 4 in. thick. The special bricks are laid in cement, six to a circle, around a lubricated pipe used as a form, and lowered in sections inside the large drive pipe; the bottom section is seated in a socket drilled in the solid rock, having the same inside

Jan 1, 1941

By Benjamin LeRoy Miller, Joseph T. Singewald

For a number of years Russia, India and Brazil have outranked all other countries as producers of manganese ores. During the 5 years immediately preceding the European war, the average annual production of Russia was 844,000, of India 694,000 and of Brazil 200,000 long tons. Since the outbreak of the war there has been a considerable falling off in the Russian and Indian production, particularly in the former, whereas the production of Brazilian ores has been greatly increased, amounting in 1914 to over 250,000 tons and in 1915 to nearly 350,000, with conditions favorable for a still larger production in 1916. Manganese is one of the few industrially important metals that are not produced in the United States in quantity commensurate with our needs, so that we have been compelled to import annually about 300,000 tons, having a value of over $2,000,000, and these ores have been obtained from the three countries mentioned above. Their rank as contributors to our imports of manganese ores was India, Russia, Brazil; and in 1913, Brazil contributed only one-fifth. During the past 2 years Brazil has furnished rapidly increasing quantities to this country, and, with the falling off of imports from India and Russia, has become our principal foreign source. In 1914, Brazil furnished two-fifths of the imports and more than India or Russia, and in 1915 over nine-tenths. The manganese ores of Brazil are consequently of more than usual interest to us at this time. The Manganese-Ore Distbicts of Brazil , The manganese mining industry of Brazil dates from the year 1894, and since that year the total production has been over 3,000,000 tons. With the exception of a small quantity produced in the State of Bahia from deposits west of the City of Bahia, this output has come from the

Jan 1, 1917

By Paul M. Tyler

The term "milling" as applied to nonmetallic minerals often refers merely to pulverizing without preliminary beneficiation. As applied to dimension stone, it embraces all the gteps involved in shaping and giving the desired finish to blocks. Processes such as sawing, planing, rubbing and polishing seem far removed from milling as the term is used in ore dressing, nevertheless they involve the element of concentration, for only 25 to 50 per cent of the gross quarry output may leave the mill as finished products after imperfect stone has been culled and the rough blocks trimmed. On the other hand, numerous nonmetallic minerals have to be concentrated in much the same manner as low-grade ores. Engineers and machinery manufacturers have begun to recognize more clearly the opportunities awaiting them in the nonmetallic field and have brought with them the methods and equipment developed in metal-mining camps, occasionally with little modification. General Economic Considerations Approximately one-half of the total value of the mineral production of the United States represents mineral fuels, and the other half is about equally divided between metals and nonmetals, the nonmetals recently having become relatively more important. In terms of volume the domestic output of nonmetallic minerals other than fuels is more than 10 times the annual output of metals. Considered on the basis of industrial utility and general commercial and military significance, moreover, the flow of nonmetallic mineral products is quite as needful to our national integrity and well-being as is that of metals, fuels, or other basic materials. Despite their importance individually and as a group, the nonmetallic mineral industries differ so widely in essential characters and economic environment that producers thereof have been slow to develop a community of interest among themselves or with the metal-mining fraternity. A spirit of change is in the air, rule-of-thumb methods soon may be relegated to limbo, and new methods—especially time-tested ideas borrowed from ore-dressing practice—are being introduced. A faithful record of plant practice in certain of these fields, however, must register

Jan 1, 1935

By L. C. Raymond

Valuations in the mineral industry differ from those of other enterprises because mines and oil wells have a definite life so cannot be considered a perpetuity. This requires that in any mineral-property evaluation the recovery of invested capital is necessary during the life of the property. Capital write-offs for nonextractive industries are assumed to be continuously plowed back to sustain the operation and produce yields on the capital invested. The extractive or mineral industry, however, generally attempts to return to the investor both interest and principal during the life of a property. Normally this is done currently and the dividend includes both items. Where the mineral property possesses large reserves and the life factor approximates a perpetuity, the return on investment is generally comparable to that of industrial stocks. The valuation of a mineral property, at best, is based on educated estimates and judgment factors. This is particularly true as it relates to estimating selling prices over a long term or assessing the quality of management. Also, it is possible to make various assumptions as to rapidity of working out the deposit, varying time for start-up of operations, varying earning rates, so as to obtain different results with the same basic facts. Thus it is not surprising that two engineers, irrespective of their abilities, may not agree exactly even when given the same facts, but their results should be close enough to be used in establishing a fair value for trading purposes. The valuation is no better than the source of basic data and the soundness of judgment factors. Fundamentally the basic principles of mineral valuation are similar for base metals, sulfur, oil, or any other mineral. Each mineral, however, requires an engineer to have a knowledge of such factors as its occurrence, distribution, mining and processing methods, and marketing problems in order to gather and analyze all the facts and data that have a bearing on the earning potential of the property. Present Value of a Mineral Property In essence the present value of a mineral property is a sum of money in today's dollars that future income from the property are worth. It differs from the total anticipated earnings by the amount of the interest that the unrecouped investment could be expected to earn during the period of recoupment. Thus, if one could accurately estimate what a mineral property will earn during its life, after deducting all operating, administrative, capital, interest, and tax charges, the determination of present value would be a relatively simple mathematical calculation. Normally, where the expected life of the mineral property extends beyond 20 or 25 years, the discounted value of earnings beyond this period is relatively small. The petroleum industry generally discounts the annual cash flow of an operation rather than earnings since, for tax-saving purposes, earnings are kept

Jan 1, 1976

By W. C. Phalen

SALT-MAKING PROCESSES THE production of salt in the United States divides itself at the outset into two distinct classes: (1) The mining of rock salt and its purification and separation into marketable sizes, and (2) the production of salt by evaporation from brines, bitterns, and other solutions. The processes employed at the present time in the manufacture of salt by evaporation may be outlined as follows: 1. Solar evaporation. 2. Direct-heat evaporation (a) in open kettles; (b) in open pans. 3. Steam evaporation, (a) in jacketed kettles, (b) in grainers. 4. Vacuum-pan evaporation. In this paper only the solar-evaporation processes practised in different parts of the United States will be described. SOLAR EVAPORATION Localities In the Eastern States the solar-evaporation process is not generally employed for climatic reasons. In the Western States, particularly in California and Utah, the great bulk of the salt produced originates in the solar-evaporation process. Of the Eastern States producing salt, this process, so far as the writer is aware, is employed in New York State only.

Jan 9, 1914

By E. A. Anderson, M. L. Fuller

The copper-zinc phase equilibrium diagram has been the subject of many investigations. Until recently, however, the boundary of the terminal solid solution of copper in zinc (eta) has not been thoroughly investigated. This paper reports determinations of the solid solubility of copper in zinc at temperatures from 100' to 400' C., the course of the liquidus and solidus for the eta solid solution and determinations of the peritectic temperature and peritectic point for the reaction between epsilon and the melt to form eta. The liquidus of the eta phase was determined by thermal analysis and the solidus by the microscopical examination of specimens quenched from temperatures above and below the solidus. The temperature of the peritectic horizontal was obtained by thermal analysis and the composition at the peritectic point was determined by extrapolation of the solid solubility boundary of the eta phase to the peritectic horizontal. The solid solubility boundary of the eta solid solution was investigated very carefully. Particular care was used to achieve equilibrium in the alloys at each temperature selected. The X-ray, electrical conductivity and microscopical methods mere used in determining the solid solubility limits. The X-ray method measures the changes in the solvent lattice with increasing solute content and in this manner locates the composition of the alloy at which no further change in the solvent lattice takes place, the limit of solid solubility. The method of electrical conductivity measures the conductivity of the alloys of a graded series of compositions, whereby the solubility limit is indicated by a discontinuity in the conductivity-composition relationship. The microscopical method distinguishes, by direct inspection, between the homogeneous solid solution alloys and those having a secondary constituent in addition to the solid solution phase, and thus indicates from the examination of a series of alloys the solid solubility limit.

Jan 1, 1934

By W. E. Remmers

The defect in wire known as "cuppiness" has appeared and disappeared from time to time but the exact cause of its appearance or disappearance has not heretofore been known definitely. This defect is not limited to one particular metal or alloy but seems to be found at various times in all of the materials that are drawn into wire. Fig. 1 represents cuppy wire made from an aluminum alloy and Fig. 2 illustrates copper wire that became cuppy in drawing without intermediate annealing. Differences of opinion are current among the manufacturers of wire and in the literature (see bibliography at end of paper), some believing that the source of the trouble lies in segregation in the wire rod, oxides, sulfides, slag, etc.; others that the trouble is created by an unevenness of stress distribution across the section of the wire, usually thought of as being a function of die shape. All of the published work is of a qualitative rather than a quantitative nature. With this in mind, it was deemed advisable to make a study of the shape of the wire-drawing dies, as well as the oxygen content of the copper to be drawn. Experimental After several methods were tried, it was found that by studying the contour of the butt-end of the rod after drawing a measure of the "working" across the section of the wire could be made. The butt-end of the annealed rod was not sheared but was sawed off. The end was then smoothed with a fine file so that the plane of filing was perpendicular to the drawing axis. It is to be noted that this method is not an absolute measure of the distribution of cold working but is a very good indicative means of studying comparative values. The method of examining a tension break in wire was found to be the most sensitive in detecting cuppiness. Other methods, such as microscopic examination of longitudinal sections, X-ray radiographic studies, etching away of outer layers with nitric acid, and fracture by bending, can all be used to identify cuppy wire but the tension break will give the fracture characteristic of cuppiness before any of the other methods can

Jan 1, 1930

By R. E. Reed-Hill

The lattice reorientations in (1011) and (1013) twins of pure magnesium have been investigated using polarized light. Both forms (Ire subject 20 almost complete second-order twinning on the (1012) plane of the first-order twin. The observed deviations of composition planes by 6 and 3 deg, respectively, from coherent twinning planes are caused by second-order twinning. The experimental data indicate that (1011) and (1013) are reciprocal twins with a twinning shear 0.136. In a previous paper1 it was shown that the primary fracture mechanism in single crystals of magnesium strained in tension parallel to the basal plane is parting or fracture inside twins. In the temperature interval 25oto286oC, the observed twinning form, dominant in fracture, was a very small twin which formed in bands. Because these twins were very small and appeared in extensively deformed regions they did not lend themselves to X-ray analysis. Lacking Cou-ling and Pearsall&apos;s2 recently reported polarized light technique for magnesium, the twinning plane indices (K1) were originally determined by two surface composition plane measurements. This plane fell in a major zone (axis < 1120>) at an angle of 55.75 deg to the parent crystal basal plane. Because its habit deviated by 6 deg from{l0ll), 61.9 deg, the experimental data per se were not consistent with simple (1011) twinning and, for expedience, the twin was designated with habit plane indices (30341, 54.5 deg, representing the lowest set of indices corresponding to measured angles. Couling, Pashak, and sturkey3 have also found bands of reoriented lattice with a similar habit in polycrystalline specimens of magnesium and certain dilute magnesium alloys. These bands are significant because their formation in large numbers during plastic flow permit specific magnesium alloys to undergo very extensive deformation by cold rolling. Using polarized light2 they showed that the basal plane in the reoriented material was nearly parallel to the band habit and, as a result, proposed a mechanism for band formation involving a double twinning process in which (1011) twins form and then retwin according to (1012). Because of the obvious similarity between the twin bands observed in single crystals and in polycrystalline specimens, it was decided to investigate if the two phenomena were not identical and, if possible, to verify the retwinning hypothesis. The present paper is a report of this investigation and shows that the twins with the (3034) habit correspond closely to retwinned (l011) twins. Evi- dence is also given for an analogous retwinning process in (1013) twins. EXPERIMENTAL PROCEDURE Rectangular single-crystal specimen deformed in tension (stress axis in the basal plane parallel to [1010], as previously described,4 were polished electrolytically by Jacquet&apos;s method5 and etched in acetic picral.2 All twins studied in this investigation belong to a major zone, whose axis, [1210], was perpendicular to both stress axis and two sides of each specimen [(1210) surfaces]. These latter contain the plane of shear of the twins and measurements of the basal plane trace of twins on these surfaces determines the lattice orientations of the twins. The position of the basal plane in each case was determined with a polarizing microscope using a modification of the technique of Couling and Pearsall.2 For each twin the four positions of maximum extinction were measured, the data averaged, and then the pair of extinctions corresponding to the basal plane was determined by rotating the microscope stage and observing the position at which the color changed from orange to blue with a gypsum red, first-order plate inserted between the crossed Nicol prisms. EXPERIMENTAL RESULTS (1013) Twins—In general, especially in speci-mens deformed at 150°C, (1073) twins appear in greater numbers and larger sizes than (1011) twins, and the lattice reorientation inside these twins is therefore easier to study and measure. Fig. 1 shows an area of an unetched and unpolished (1210) crystal surface containing a number of (1073) twins sloping upward to the right at about 29 deg with the basal plane of the original crystal (horizontal direction). Slip line segments may be seen in both the parent crystal (running horizontally) and in the twins (sloping downward to the right at approximately -22 deg with the horizontal). As may be seen in Fig. 2, the slip lines in the twin are not at the proper angle (64 deg from basal plane of the

Jan 1, 1961

By G. R. Love, C. C. Koch

The changes in superconducting properties with aging time have been studied ,for the pecipitation reaction in a Tc-30 at. pct V alloy. Superconducting critical temperature, upper critical field, and relative critical current density were determined by ac susceptibility techniques. Aging produces changes in critical temperature of both matrix and precipitate which can be rationalized by compositional effects. maximum flux pinning (critical current density) occurs at a time during aging when subgrain boundaries are completely decorated with precipitates and the subgrain centers remain precipitate -free. The particular effectiveness as barriers to flux motion of planar defects which enclose regions of low deject density is discussed. THE precipitation of a second phase can dramatically modify the superconducting properties of type I1 super-conductors. According to Livingston and Schadler1 one might expect changes in the primary, secondary, and tertiary superconducting properties of the material. Changes in matrix chemistry caused by precipitation can alter the fundamental superconducting parameters; critical temperature, Tc, and thermody-namic critical field, Hc. The concimitant changes in electron mean free path (reflected in normal state resistivity) can affect the critical fields Hc 1, IIc2, Hc3. Finally, the presence of precipitate particles may hinder the motion of flux lines and may considerably improve the current-carrying capacity in high-field superconductors. The influence of precipitation on superconducting properties has been studied in a number of systems.2 Magnetization measurements have been used to study the influence of precipitates on flux pinning in lead-base alloys by Livingston3 and Evetts et al4 In these alloys precipitates induced magnetic hysteresis and flux trapping. The amount of hysteresis increased with the volume fraction of precipitate and decreased with coarsening of the precipitate. Jn an Al-Zn alloy5 and an A1-Ag alloy6 the initial precipitate size was presumably smaller than a coherence length and coarsening increased magnetic hysteresis5 and critical current density.6 The influence of precipitation on superconducting properties has also been studied in several of the commercially interesting Ti-Nb7-10 and zr-Nb11 alloys. The maximum in critical current density for these alloys was confined to a narrow range of either isothermal aging time" or isochronal aging temperature7 during the precipitation reaction. Thus, experimental evidence and theoretical considerations suggest there is an optimum precipitate size, spacing, and density, and a critical composition with respect to the matrix for flux pinning. What these "optimum" values might be and the relative importance of each is still not clear, although a few generalizations can be made. It is generally accepted1&apos; that particle sizes smaller than the coherence length or larger than the inter-flux line spacing are poor pinning centers. In high Hc2 materials, precipitate sizes for maximum values of critical current density lie in the range of 50 to 2000Å,9,7 and there are indications that increasing dissimilarity between precipitate and matrix produces increasing pinning force.13 Because of several interesting features of the aging reaction in a Tc-30 pct V alloy, we have chosen to study the influence of precipitation on the superconducting properties of this alloy. The physical metallurgy14 and a survey of the superconducting properties" of the Tc-V alloy system have been reported. The Tc-V phase diagram is presented in Fig. 1. At 1500°C the Tc-30 pct V alloy is in the single phase 6 field. Samples quenched from the 6-phase field have a CsCl structure X-ray diffraction pattern at room temperature and it has been proposed that the 6 structure is closely related to the bcc lattice.14 When held isothermally below the eutectoid temperature, 115O°C, the 6 phase decomposes into the CsCl and hcp phases.

Jan 1, 1970

By Robert M. Grogan, Gill Montgomery

Fluorspar, the commercial name for fluorite, is a mineral composed of calcium fluoride, CaF,. Its valuable properties are due to its content of fluorine, and it is the principal commercial source of that element. The name is derived from the Latin word "fluere," to flow, because the mineral has a low melting point and is used in metallurgy as a flux. Cryolite is a sodium aluminum fluoride, Na,AlF,. It is a rare mineral which has been found in commercial quantities in only one place in the world, Greenland. Small amounts of it are shipped from stock in that country, and its place in industry has been taken over almost completely by synthetic cryolite. Because of the relative unimportance of cryolite, discussion of it has been relegated to a short section at the end of this chapter, which is principally concerned with fluorspar. History Fluorspar was used for ornamental purposes by the Greeks and Romans, who fashioned such things as vases, drinking cups, and table tops from it. Various peoples including the Chinese and the American Indians carved ornaments and figurines from large crystals. Its usefulness as a flux was known to Agricola (1564), who wrote about it in 1546. Mining began in England about 1775 and at various places in the United States during the period 1820 to 1840. Production became substantial following the development and widespread adoption of the basic open hearth method of making steel, in which fluorspar is used as a flux. After that, production and usage were stimulated by growth in the steel, aluminum, chemical, and ceramic industries and were accelerated by World Wars I and II. Fluorocarbons entered the picture in 193 1 and the use of anhydrous hydrogen fluoride (HF) as a catalyst in the manufacture of alkylate for high octane fuel blends began in 1942. The development of the froth flotation process in the late 1920s, a differential flotation scheme for separating fluorspar from galena, sphalerite, and common gangue minerals in the 1930s, and the application of heavy-media concentrating methods to the treatment of low grade ores in the 1940s were outstanding technological contributions that enabled increased production of fluorspar concentrates. In recent years the development of pelletizing and briquetting processes for making flotation concentrates into gravel-size particles for use in steel furnaces and the development of more efficient and selective flotation schemes for treating crude ores containing abundant dolomite and barite have been major improvements in the industry.

Jan 1, 1975