Search Documents

The problem of surface support in coal mining is naturally divided into three branches: 1. Surface covered with improvements of such value as compared with the value of the underlying coal, or with such elements of danger to mining, that absolute support is essential. 2. Surface with improvements of less value than the underlying coal such that moderate settlement may be permitted, but destructive settlement must be avoided, either by reason of danger to human life or unwarranted property damage. 3. Surface of relatively small value as compared with the underlying coal where destructive settlement may be permitted. First Problem In the first case it is evident that the original support must be maintained either (a) by leaving ample pillars and confining the coal recovery to a very conservative first mining, (b) by so supporting less conservative first mining by filling or flushing that the gradual deterioration of the pillars may be prevented and subsidence avoided, or (c) by incompressible support as masonry either as an adjunct to insufficient pillars or in place of the original coal support. a. From tests made by the Scranton Engineers Club, it appears safe to figure on 2000 Ib. per sq, in. as the safe squeezing strength of coal pillars in place, provided that these are, as usual, not higher than their least horizontal dimension; and from this figure the percentage of pillar to be left for various depths may be easily calculated. For safety in this

Jan 1, 1930

By David R. Mitchell, Byron M. Bird

THE revision of this chapter has presented a problem in that heavy-medium jigging has come into the picture since the chapter was originally written (seven years ago), a practice in which an artificial medium is built up and maintained in the jig circuit. As this development makes the jig a "true" heavy-medium process, the method belongs in the chapter dealing with such processes. Although putting this development in its proper position in the book involves some repetition, this seems to be the best procedure, and it has been followed. As the chapter on jigs in its original form was intended to be more or less a handbook on jigging for the use of the practical man, and the great bulk of the material therein is still generally applicable, the text has been re-used in large measure. Two major changes should be noted: (1) the portion of the text relating to the refuse-withdrawing mechanism of the McNally-Pittsburg jig has been entirely rewritten, and (2) a description of the hutch valves on the Jeffrey jigs has been added. Jigging is the stratification of a mass of solid particles in upward and downward pulsations. The stratification usually is effected in a rectangular open-top container having a perforated bottom through which the pulsations of water are applied to the materials to be separated; in separating coal, to a mass of coal and refuse. Jigging usually is a continuous process involving three steps: (1) the reception of the raw coal, (2) the stratification of the coal and refuse so that the refuse settles to the screen plate, and (3) the overflow of the cleaned coal and the withdrawal of the refuse collected on the screen. The jig is the most universal washer ever devised. It is handling in practice a wide range of closely sized coals and ores, mixed sizes of coal from 8-in. to 0 through 3/4-in. to 0, and mixed sizes of ores down to 7/32-in. to 0and even smaller. It is treating materials ranging in specific gravity from that of gold at 19 to that of coal at 1.30. It is handling feeds in which the proportions of high-gravity materials range from 90 per cent or higher, as for some iron ores, to 10 per cent or less for some coals. It is handling feeds containing all shapes of particles-round, rectangular, and flat. It is handling simple separation problems and difficult separation problems.

Jan 1, 1950

By J. E. McDonald, J. G. Eberhart

A model is discussed from which the work of adhcslon .tor liquid transition metals on aluminum oxide surfaces can he calculated, A close-packed (00011 oxygen surface on A12O3 is assumed with two different types of surface sites: one type involving metal-oxygen bonds and the other man der Waals into actions. The work of adhesion is thus expressed as the sum of these two bonsding free energies. Calculated works of adhesion for nickel, titanium, chromium, and zirconium on sapphire agree well with the experimentally determined quantities. The model is extentled to the calculation of the work of adhesion and shear stress required to remove a thin metal film from a sapphire substrate and is in good agreement with experimental values. The obsewed dependence of the work of adhesion on the free energy of oxide formation of the metal is shown to also provide an interpretation of the tittle dependence of thin-film adhesion. THIS paper presents a model for the type of bonding which occurs across a metal-A12O3 interface. The model is used to explain the results of two types of experiments in which such an interface exists: 1) the adhesion of thin metal films on Al2O3 substrates and 2) the wetting of A12O3 by liquid metal drops. The adhesion of thin films to various substrates has been the subject of a variety of investigations.'-' Benjamin and weaver3 and Bowie,6 using the scratch test developed by Heavens,10 studied the adhesion of metallic films to glass substrates. Their observations for noble-metal film adhesion agree well with an adhesion model involving a van der Waals type of bonding between the film and the substrate. For films of metals whose free energy of oxide formation. ?F°f, has a negative value. Benjamin and weaver3 and Bowie6 found a time-dependent adhesion with an initial value that can be interpreted in terms of van der Waals interactions but a larger terminal value which was related to ?F°f, Karnow-sky and Estill7 deposited films on sapphire at elevated temperatures and noticed no time dependence of film adhesion but a similar correlation with ?F°f. Because of the kinetic problems associated with thin-film adhesion it is desirable to examine adhesion in an equilibrium system. The wetting behavior of liquid-metal drops on Al2O3 provides such a system. Systems of this metal-ceramic type have been studied extensively.11 Humenik and Kingeryl2 have measured the wetting of A12O3 (and other substrates) by several metals and have pointed out that the wetting ability of these metals increases with increasing values of -?F°f. It is thus seen that thin-film adhesion and metal wetting on A12O3 are both related to the tendency of the metal to react with the surface oxide ions of the Al2O3 substrate and, because of this, both phenomena should be explainable by an appropriate model for the metal-Al2O3 interfacial bonding. In the sections that follow, wetting and adhesion data on A2O3 are reviewed and a model is presented by which these phenomena can be interpreted. ANALYSIS OF WETTING EXPERIMENTS In an equilibrium system involving a liquid-metal drop on a solid Al2O3 substrate, the work of adhesion, WAD, is defined by the Dupre, equation as WAD = ?s + ?L -?sL [1] where ?s and ?L are the surface free energies of the solid substrate and the liquid drop, respectively, and ?sL is the interfacial free energy. The work of adhesion is the work required to separate a unit area of the solid-liquid interface into two surfaces. The work of adhesion is usually determined from a sessile-drop experiment in which yL and the contact angle, ?, are measured. The Young-Dupr6 equation is then used to calculate WAD Wad = ?L (1+ cos ?) [2] The literature of this subject has been examined and Table I shows work of adhesion data for various liquid metals as measured on A12O3 substrates. The standard free energy of oxide formation of the metal at the temperature of the wetting experiment, ?F°f . is also tabulated in kcal per g-atom of oxygen. The data is grouped according to the gaseous atmos-

Jan 1, 1965

By Donald D. Smythe

This paper describes briefly the topography and geology of the region where the mica-bearing pegmatites are found and discusses prospecting, the quality of the mica, its preparation, and evaluation of the deposits. Muscovite mica occurs in a number of widely separated localities in Brazil, but production has come largely from deposits in the southeastern and eastern part of the State of Minas Gerais (Fig. I). There the deposits form a discontinuous zone, which starts at a point go km. north of the city of Rio de Janeiro and extends north for some 500 km., roughly parallel to the coast. A maximum width of 180 km. is reached along the Rio Doce. To the west in Minas Gerais, and extending east into the states of Espirito Santo and Rio de Janeiro, the mica zone proper is fringed by areas in which there are scattered occurrences of mica-bearing pegmatites. A few of these outlying deposits have produced commercial mica, but most of them are unimportant. To the southwest, in the State of Sao Paulo, there are a number of mines, which at one time produced a very considerable amount of sheet mica, largely as a byproduct of kaolin mining. These deposits, and a few others lying between them and the main productive areas to the northeast, appear to be the southwestern continuation of the strong Minas Gerais mica zone. In the vicinity of Conquista, just north of the Minas Gerais boundary in the State of Bahia, and still farther north, near Jacobina, there are several known mica deposits. Their location indicates that they may be the northern continuation of the main mica zone. The major part of Brazilian mica production has come from four areas within the mica zone proper; from north to south, Governador Valadares, Raul Soares, Espera Feliz, and Muriaé.. The first is go km. from north to south and reaches a maximum width of 180 km. The Raul Soares area extends 135 km. from northeast to southwest, and in places is 80 km. wide. The Espera Feliz area is 100 km. from north to south, and reaches a width of 35 km. The Muriai. area extends 150 km. from northeast to southwest and its width reaches 40 kilometers. Between the known productive areas, and in the areas directly to the southwest and to the north of them, little mica has been produced. These gaps, as well as certain irregularities in the outline of the mica zone itself, are to be ascribed either to lack of prospecting or to conditions preventing the discovery of mica, rather than to its nonexistence. Elsewhere in Brazil mica has been reported from eastern Goiaz, Ceará, Pernambuco, Rio Grande do Sul, Matto Grosso, and Amazonas. Production from these sources is negligible at present. Because of the inferior quality of the mica from the more accessible of these localities, and the operational difficulties occasioned by the remoteness of others, it is improbable that they will become important producers for some time to come.

Jan 1, 1948

By F. E. Buch

The smelter is designed for a production capacity of 10,000 short tons of blister copper per month, when operating on the present concentrate grade. The :smelter lay-out is shown in Fig I. The major units of equipment comprise two reverberatory furnaces, three 13 by 30 ft Peirce-Smith converters, two straight line casting machines, one being served by a 13 by 30 ft holding furnace and the other by a ladle tilting quadrant, two converter aisle cranes and two converter blowers. The plant is compact and the general arrangement of standard gauge railway tracks and conveyor belts provides for a smooth flow of incoming materials and metallurgical products. Concentrate is received by conveyor belts and fluxes in standard railway trucks. The local track system is covered by an electric trolley locomotive. The Smelter treats a wet (10 pet moisture) flotation concentrate containing approximately 53 pct total copper and 0.9 pet oxide copper. The predominating minerals are chalco-cite, chalcopyrite and bornite accompanied by small quantities of malachite and cuprite. The gangue is highly siliceous and requires limerock as a flux. Metallurgy would be straightforward were it not for the necessity for eliminating bismuth which occurs as an impurity in the ore along with the copper. Directly or indirectly most of the Smelter problems can be traced to the necessity for bismuth removal. Copper recovery, based on new copper treated, averages 97.5 pct. General Description Flotation concentrate, containing 10 Pet moisture, is conveyed from the filter plant to the smelter storage bins by conveyor belts, the material being weighed in transit by a revolving drum type of weigh-hopper manufactured by Samuel Denison and Son, Ltd. The weigher consists of a steel drum with dished ends carried on a horizontal shaft and rotated by an 8 hp squirrel-cage motor through a worm and Spur reduction gear. A feed mouth in the drum permits of filling and discharging. The whole unit is supported on a framework resting on weighing levers, which in turn connect to transfer levers, thence to an indicator of the steelyard type situated 16 ft from the centre line of the drum. The indicator is of the "Denison" patent equilibrium controlled ticket stamping type, insuring mistake-proof records by a combination of electrical and mechanical movements which Prevent the operator from printing until the cover enclosing the steelyard is closed and until the poise-weights have been Set correctly to the weight of the hopper and contents. The machine is capable of weighing 30 short tons at a time but the usual load is 28 tons. After obtaining the gross weight the drum is rotated and discharged into a receiving bin situated below it. The empty drum is weighed and the net weight re-

Jan 1, 1949

By L. G. Huntley

The occurrence of oil or "tar" in Mexico was mentioned as early as the seventeenth century by Friar Sagahun, who gives the Indian name "chapopote," by which these asphalt seepages are still called. This asphalt was apparently used, as it has been used by primitive people in many parts of the world, in religious ceremonies and for medicinal purposes. Travellers also report that the ruins in Yucatan and the pyramids in southern Mexico show traces of the use of "chapopotel' as a building cement.l DeGolyer says that the first attempt to exploit oil or gas in Mexico in a commercial way is shown by the records of the Memoria de Fomento of 1865, when permission was granted to a Senor Ildefonso Lopez to exploit the deposits of petroliferous substances in the San Jose de las Rusias area in the State of Tamaulipas. Other concessions follow, and probably refer to surface seepages which occur in that district. This was several years after the discovery of oil in Pennsylvania. In 1868, a well 125 it. deep was :drilled by a company organized in Mexico City, in what is now known as the,, Furbero district, and a little oil was refined there. In 1873, residents of Tampico denounced seepages along the Tamesi River, and asphalt was mined near Tempoal in the Canton of Tantoyuca. No drilling was attempted. But between 1880 and 1883 several shallow wells were drilled for oil in Mexico, two of them being near the present Potrero de Llano field west of Tuxpam. The wells were drilled by a Boston company with Canadian rigs, and are said to have reached a depth of about 400 ft., while one is reported to have flowed. Several other abortive attempts were made to drill for oil between 1885 and the beginning of the present century, about which time the Mexican Petroleum & Liquid Fuel Co., Ltd., in which Cecil Rhodes was interested drilled 24 wells unsuccessfully, several of them as deep as 1,500 ft., in the State of Vera Cruz. Also Messrs. Doheny and Canfield of California pur-

Jan 1, 1916

By Hjalmar W. Johnson

IT has long been accepted that blast-furnace practice varies to some degree with the coke used. While the qualities desirable in iron have been known for some time, the qualities in coke that produce such iron have not been established. There are no objective standards for blast-furnace coke, which is usually described in general terms, as good or bad. Many experienced operators believe that coke cannot be measured objectively except by using it in the furnace, noting the result, and labeling the coke according to furnace operations. This is admittedly unscientific, and besides is useless for the two main purposes for which a measure of coke quality is needed: (I) to produce the best possible coke from the coals and equipment on hand; (2) to test new coals and determine their value for blast-furnace coke. In seeking such an objective measure, much work has been done on tumbler tests, shatter tests, sizes of coke, porosity, specific gravity, reactivity or combustibility and other tests, but as yet very little has been published in which conclusive correlations have been established between such objective measures and furnace operation. In our study of the problem during the past 8 years we have developed no new measures of coke quality, but we have collected data that are presented here in the hope that they may assist in further work, so that at some future time there may be developed such positive measures. The purpose of this paper is to show that there are variations in coke and that such variations do influence the operation of blast furnaces. At the same time we must remember that there are variations in blast-furnace operation and it may be the blast furnace that is at fault. This correlation of coke properties with blast-furnace operation will be worked out in the following steps: I. Discussion of a period when a change in the coke resulted in an increase in efficiency on one furnace and a decrease in efficiency on another. 2. Adaptation of the inefficient furnace to the available coke so that normal efficiency was restored. 3. The use of radial distribution: a discussion of the effect of size of ore layer in adapting blast-furnace operation to the coke. 4. An example of a change in size of coke and the detrimental influence on the production of one furnace. 5. An example of a change in size of coke, together with manufacturing data, to show why it changed, the conclusion being that coke is a product with an optimum value. 6. Illustration of the fact that coke has different optimum values on two furnaces, with discussion on adaptation of operation so the optimum values will be the same. 7. Limitations of the use of screen tests as an objective measure of coke quality. 8. Importance of uniformity in coke. FUNCTIONS OF COKE AND QUALITIES REQUIRED TO PERFORM THESE FUNCTIONS Coke has three important functions in a blast furnace: (I) to furnish most of the

Jan 1, 1941

By Charles B. Dudley

DEAR SIR: It is now nearly three years since my first report to you on the subject of steel rails was written. That report, as you will remember, dealt principally with the question of the relation between the chemical composition and physical properties of steel rails end their power to resist crushing and fracture in actual service. Other matters were referred to or touched upon in that report, but the main question was, Why do some rails crush or break in service while others do not? Yon will doubtless remember that the principal conclusion arrived at was, that the softer rails are less liable to Crush or break in service than the hard ones. Or, in other words, so far as conclusions could be drawn from the chemical analysis and physical test of 25 samples of steel rails which had actually been in service, these conclusions were that those rails which have the smaller amounts of carbon, phosphorus, silicon, and manganese are less liable to crush or break in service than those which have larger amounts of these elements. Or, again, looked at in the light

Jan 1, 1881

By Werner Engelmaier

Constant-strain rotating-bending fatigue tests were conducted on 2024-T3 aluminum alloy constant-strain McAdams-type specimens in ultrahigh vacuum, 10-lo Torr, and in atmospheric air. In the elastic strain range the ratio of vacuum-to-air fatigue life varied from about 10 at a maximum bending stress of 37 ksi to near unity at the endurance limit. After 10 pct of the fatigue life, intergvanular microcracks appeared on the surface which did not appreciably propagate further until the last 5 pct of the fatigue life, where trans-granular cracks propagating first in slip-plane cracking and then in the stress-dominated mode led to failure. No reduction in residual tensile strength resulted from the fatigue of the specimens short of fracture. The mechanism governing the fatigue life operates between the occurrence of the intergranular microcracks and the initiation of the trans granular cracks. MORE than forty years ago, Mc Adam' and Haigh2 published the first systematic studies showing that the fatigue properties of metals were greatly affected by environments. Gough and sopwith3 found in a later study that the fatigue life of metals subject to corrosion can be substantially increased by reducing the atmospheric pressure. This and their later work4'5 was, however, done in a vacuum of only 10~3 Torr. Subsequent studies6-' at a vacuum of 10- Torr showed that water vapor is the primary agent affecting the fatigue properties of aluminum alloys. Only recently was ultrahigh vacuum used for fatigue studied.l Various theories have been put forward to explain this phenomenon. Wadsworth and Hutchings12 postulated that cracks form very early in the test and that the chemical attack by the corrosive components of the atmosphere at the root of the cracks enhances the speed of the crack propagation. They also noted that chemisorbed layers of gas on the fresh crack surfaces prevent cold welding of the crack and make the separation irreversible. Ham and Reichenbach, on the other hand, reported that their specimens showed no cracks after a run in vacuum, even though the runs were long enough to have caused the specimen to fracture in atmospheric air. They also reported that in argon at 0.14 Torr the fatigue life was about 5 times longer than at 7 X lo-' Torr. Jacisinll reported that fatigue tests in dry nitrogen showed results close to those obtained in ultrahigh vacuum. The present experiment was designed to determine the extent to which cumulative fatigue damage, i.e., the accumulation of length of fatigue cracks, reduces the residual static tensile strength of an aluminum alloy in both ultrahigh vacuum and atmospheric air and to obtain fatigue-life data for this aluminum alloy at various strains. It was also hoped that information ex- tracted from these data might support one of the previously mentioned theories. 1) EXPERIMENT Test Specimens. The material tested was commer-cial 2024-T3 aluminum alloy. In addition to aluminum, this alloy contains approximately 4.4 pct Cu, 0.5 pct Fe, 0.5 pct Si, 0.6 pct Mn, 1.5 pct Mg, plus smaller amounts of other elements.13 Some typical mechanical properties of this aluminum alloy are listed in Table I.'~ The material was used in the as-received condition, i.e., solution-treated and cold-worked. Mc Adam-type1' constant-stress specimens and notched fatigue specimens were machined from 4 -in. -diam rods, Fig. 1. The critical section of the McAdam-type samples was polished with a 45-deg spiral motion to a No. 8 microfinish. The notch in the notched specimens was machined on a lathe with a forming

Jan 1, 1969

By G. Sachs

THE iron-rich iron-nickel alloys have at-tracted considerable academic interest in recent years. The carbon-free alloys are of minor practical importance, but they are Atomic per cent nickel FIG. I. FIG. 2. FIG, I.-HONDA'S AND MERICA's IRON-NICKEL DIAGRAM, FIG. 2.-MARSH'S IRON-NICKEL CONSTITU-TIONAL DIAGRAM. the base of many alloys with various out-standing properties. The iron-nickel alloys, therefore, have been investigated exten-sively regarding both their structures and their properties. The researches on these alloys up to 1938 have been collected and critically reviewed by J. S. Marsh,1 and will be discussed in some detail in the sec-tions of this paper dealing with specific subjects. These numerous investigations have not succeeded in establishing the equilibrium conditions in this system. Alloys containing more than a certain amount of nickel (8 to10 per cent Ni) undergo the allotropic transformation extremely sluggishly, both on heating and cooling, showing a large hysteresis,2 which is not dependent upon

Jan 1, 1940

By W. H. Brandt

THERE has been much progress in the last two decades in understanding the hardenability of steel. Roughly, the progress has been along two lines, which may be designated as empirical and fundamental. This empirical work has progressed to the point where steels may be manufactured to the desired characteristics quite closely and heat-treatment and application problems can be approached with considerable confidence. Particularly noteworthy among the empirical work is that of Grossmann,12 who has given formulas for calculating hardenability as a function of composition, and the establishment of the isothermal transformation curve by Davenport and Bain.13 The latter does not fall entirely in the class of an empirical study, for while it provides a means of presenting a tremendous amount of empirical data in the form of a single curve, it also outlines clearly the problems that face the fundamental investigator. The isothermal transformation curve shows clearly that the phenomena occurring in the neighborhood of the knee of the curve are those that limit the hardenability of steel. Above the knee of the curve, the product of decomposition of austenite is lamellar pearlite and fundamental progress has consisted chiefly of a detailed study of structure and formation of pearlite, largely at the hands of Mehl and his collaborators.1-5 They have shown that formation of pearlite proceeds by a process of nucleation and growth and they measured both the nucleation and growth rate. However, there is still a wide gap between our empirical knowledge and fundamental knowledge, owing largely to the fact that there is no satisfactory theory of nucleation rate or of growth rate. This paper is being written in an attempt to fill in a small part of the gap. A method was presented recently14 for calculating the velocity of edgewise growth of pearlite using an expression for the carbon concentration that satisfies the diffusion equation. The edgewise velocity of pearlite growth in a plain carbon eutectoid steel was calculated, using linear extrapolations of the ferrite and cementite solubilities. While the results are in fairly good agreement with the experimental facts, the calculated velocity of edgewise growth is smaller at 600°C. than G, the radial growth velocity of pearlite nodules, whereas one would expect it to be larger. In this paper the calculation will be repeated using a new extrapolation for the ferrite solubility, which gives better agreement between G and V, the calculated velocity of edgewise growth. A calculation will also be made of the effect of carbon content on velocity of edgewise growth, and the problems of calculating the effects of other alloying elements on growth rates will be discussed. It will be assumed that the mechanism of pearlite growth, established by Mehl and

Jan 1, 1945

By Sidney Diamond, Charles Wert

The anelastic behavior of Ni-C alloys of nominal 0.5 wt pct C has been determined over a wide temperature range. The most prominent damping effect, that due to the presence of C-C pairs, was measured both above and below the Curie temperature. The effect on diffusion of the C-C pairs by magnetic spin ordering is deduced to be very small. The diffusion coefficient for C-C pairs in nickel is given by the expression ThE solid-state diffusion of both interstitial and sub-stitutional solutes in ferromagnetic solvents has been the subject of a number of investigations. Measurements of the self-diffusion of iron,"' the diffusion of nickel1,4 gold,"1 and cobalt4 into iron, the diffusion of vanadium in an Fe-V alloy,' and the diffusion of cobalt and nickel in Co-Ni alloys9 show an unusual behavior. In both the ferromagnetic and paramagnetic regions, far removed from the Curie temperature, the diffusion coefficient, D, obeys an Arrhenius relation. However, in the ferromagnetic region D is markedly lower than would be expected from an extrapolation of D from the paramagnetic region; this results in an increase in the activation energy in the ferromagnetic region. The cause of this effect for self- and substitutional diffusion is uncertain. Since substitutional diffusion is presumed to proceed by the vacancy mechanism, it has been variously suggested that the increase in activation energy below the Curie temperature is due to one of the following causes: 1) an increase in the energy of formation of a vacancy because of local demagnetization around the vacancy,2,3 2) a decrease in vacancy mobility in the ferromagnetic state,' or 3) an effect on the entropy of motion of a vacancy in the ferromagnetic state.5 Quite another explanation for the observed effect has been proposed by Borg.7 The diffusion coefficient is a function of the elastic constants of a metal. Since the temperature dependence of the elastic constants often changes at the Curie temperature, the temperature dependence of D might be expected to undergo a universal change in the vicinity of the Curie temperature. The magnitude of the change in D would, of course, depend on the magnitude of the change in the elastic constants. One might attempt to differentiate between vacancy effects and elastic effects by making measurements on interstitial alloys, in which vacancy effects play no role. Some measurements of this type have been made; this paper reports additional observations. Measurements of the diffusion of carbon in a Fe by a tracer technique8 and of the diffusion of carbon in a Co and in Co-Fe alloys by a decarburization method9 reveal a small effect, if any, on D of the magnetic change at the Curie temperature. If the effect of spin ordering is only to alter the parameters controlling formation or mobility of a vacancy, interstitial diffusion should indeed remain unchanged through the magnetic transition, as these measurements imply.

Jan 1, 1968

By R. Y. Williams

In the United States, fully 98 per cent. of the anthracite and bituminous coal tonnage obtained from underground operations is mined by the room-and-pillar system. Under this system, the total cost of the coal f. o. b. railroad cars contains as its greatest single item the money paid for "labor." Each labor dollar in an average bituminous mine may be subdivided into 85 c. paid for work done inby the gathering turnouts (including all work at the face), and 15 c. outby that point (including all work in and under the tipple). In an average anthracite mine, the corresponding figures are 70 c. and 30 c., the larger breaker force accounting mainly for the difference between these and the bituminous figures. The next largest single item after "labor" is usually "supplies and power;" and a division of this item inby and outby the gathering turnouts shows somewhat the same relative proportions as has been noted under the case of "labor". During the past 10 years, the chief advances made in the coal industry have been to obtain economies through complete mechanization covering that portion of the work which lies outby the gathering turnouts. These results have been accomplished by applying scientific principles to railroad yard layout, to cleaning and sizing machinery, to dumping facilities, to roller-bearing haulage equipment, and to heavy-rail, well-ballasted trackage. But these improvements, while gratifying in their resulting economies, apply only to 15 to 30 per cent. of the important cost items. Obviously, then, the big problem before the engineers of the coal industry today has to do with the methods of mining and the layout inby the gathering turnouts. Four years ago, Weston Dodson & Co., Inc., determined to have an exhaustive study made of the conditions which must be met in order to gain complete face mechanization, and in order that such a mining layout would be based on correct underlying principles. The result of that study, which was made by the writer, led to the adoption of a method of longwall mining wherein the roof is worked on the caving system and is supported as an overhang along the face by steel jacks.

Jan 1, 1928

By Bernard MacDonald

Of the treatment of the slime-pulp of gold- and silver-ores by cyanidation, agitation is an essential part. When prepared for treatment, this pulp, consisting of ore reduced to such fineness that approximately 80 per cent. of it will pass through a 200-mesh screen, is mixed with a certain proportion of water, carrying in solution the cluantity of cyanide (KCN) and other chemicals required. The water-constituent of the pulp thus prepared usually ranges from 1 to 2 parts by weight to 1 of the dry ore. Thus constituted, the pulp is charged into treatment-tanks, the shape and capacity of which vary, according to the quantity of pulp to be treated daily and the method of agitation to be employed. Tanks have no other function in a cyanide,plant than that of being economical and corlvellient containers or receptacles for holding the pulp, solutiou, or water used in the operations. It is by agitation that the solids in the pulp charged into the tanks are kept in suspension in, and mixed with, the solution in the proper proportions required for the treatment. If the proper mixture of solution to dolids be determined to be 2 to 1 by weight (which is, approximately, 5 to 1 by volume), this proportion should be maintained in every part of the charge; that is, each solid particle of the pulp, whether it be of' 180- or 400-mesh size, should be surrounded by five times its own volume of solution throughout the whole period of treatment. The reason is, that the amount of chemicals ascertaiued to be necessary for dissolving the gold and silver contained in the solids, is held in uniform solution in the water-constituent of the pulp, and, therefore, the determined proportions of solution and solids must be maintained at all times during treat-

Jan 1, 1912

By Arthur West

It is the purpose of this paper to describe briefly some recent large power stations for blast furnaces, where the blast is exclusively supplied by gas engines using furnace gas. The stations are given in the chronological order in which they were designed, in order to indicate the various improvements suggested by experience. Fig. 1 shows the blowing-engine station of the Bethlehem Steel Co. at Bethlehem. Although the picture shows only five blowing engines, the house now contains 11 engines. In the diagrammatic plan the arrow shows the position and direction of camera. This station handles five modern blast furnaces of 450 to 500 ions capacity each. In this, as in all the other stations described in this paper, each furnace is blown by two single tandem gas engines. Ten engines are thus required for five furnaces, leaving one single tandem spare engine. This spare capacity has been shown by several years' experience at Bethlehem to be adequate to insure continuous operation. The engines in the Bethlehem station are right hand and left hand, arranged in pairs. The outboard bearings of each pair are close together so that there is not room for passageway between them. On the right of the picture are shown the inclined drums communicating with the cold-blast lines outside of building, so that any engine may be operated on any furnace. The illustration shows four cold-blast gate valves with pipes passing through wall, but since the photograph was taken the drums have been extended to take care of a fifth valve for a fifth furnace. At the extreme back of the picture can be seen the tubs of three twin vertical-horizontal Southwark steam blowing engines, which, although of modern design and as good as new, are not operated because of the greatly reduced blowing cost shown by the gas blowing engines. The next station built is shown in Fig. 2. This is the plant of the Minnesota Steel Co. at Duluth, Minn., and is at present constructed for five engines, to handle two furnaces, with one spare engine. The engines are of practically the same size as those at Bethlehem. Instead of being arranged in right-hand and left-hand pairs, as at Bethlehem, all the engines are of the same hand; this arrangement has some ad-

Jan 1, 1915

By Otto H. Henry, J. J. Cordiano

THOUGH powder metallurgy is one of the oldest of metallurgical processes, it is in its infancy as a branch of the modern field of metallurgy. As early as 3000 B.C., the ancients produced implements and weapons of iron by reducing iron ore in a charcoal fire and forging the resultant sponge while still hot into the desired shape. Melting and casting soon superseded the powder metallurgy practice, and it was not until the turn of the twentieth century that powder metallurgy was applied to the commercial manufacture of tungsten lamp filaments. From this beginning, the use of the powder metallurgy process spread to the manufacture of porous oil-impregnated bearings, cemented carbide tools, contact points, diamond grinding wheels, clutch facings, starter brushes, resin-bonded radio cores, magnets, metallic filters, and other parts. More recently, and particularly during the present war, there has been a definite trend toward the manufacture of machine parts by this process in competition with the more conventional fabricating methods. Notwithstanding these many developments, scientific progress has been slow. While many articles on powder metallurgy have appeared in the press and various publications, there have been too few contributions to our technical societies, with the result that there is a dearth of the type of information necessary for the full development of this science. It is of primary importance that the results of research and development be freely disseminated if powder metallurgy is to realize its fullest potentialities. PURPOSE OF INVESTIGATION Excluding the refractory metal field, all commercial powder metallurgical products made by a cold compressing and sintering operation contain voids. These voids can be substantially eliminated by subsequent severe working and heat-treatment, but such practice has not proved economical in most applications. By applying heat during the compressing operation, plastic deformation of the powder particles is substantially increased, and the resultant compact or briquette is practically free of voids. However, hot-pressing has many attendant problems, which at present preclude its use in the manufacture of precision parts. The more important of these are to devise: I. A die steel capable of withstanding high pressures at elevated temperatures. 2. A high-temperature lubricant capable of preventing excessive die wear and welding of the compact to the die walls. 3. A method of retaining a neutral or reducing atmosphere in the compacting zone of the die assembly. 4. A means of ejecting the hot-pressed specimen into a neutral atmosphere until reasonably cold.

Jan 1, 1945

By H. C. Schultz, F. K. Middleton Hunter

Certain local conditions were known to govern in large measure the successful adaptation of liquid-oxygen explosives to the large-scale blasting at Chuquicamata. The wide variation in hardness of the rock at this mine makes necessary the use of several types of explosives. A locally manufactured, relatively cheap black powder is used in blasting the softer waste and capping material, where a thorough displacement breaks the ground sufficiently. Before the introduction of L. 0. X., an ammonia dynamite of about 65 per cent. strength was being used exclusively in the harder underlying orebody, where a strong disruptive as well as a displacement effect is required for breaking the ore. The L. 0. X., as developed for quarry work in the United States, has a practically pure carbon cartridge material, and the explosive has an extremely high rate of detonation, which should therefore cause it to develop usefully its full disruptive effect in hard ground. The individual blasts at Chuquicamata arc large, black-powder shots which dislodge masses of rock averaging 250,000 tons each, and dynamite shots which dislodge masses averaging 80,000 tons each. It was desirable, therefore, to attempt to displace with L. 0. X. the faster, higher-cost ammonia dynamite used in the smaller blasts. It was not considered practical to attempt to displace the low-cost black powder with 1,. 0. X., as estimated costs showed no probable saving if this were accomplished. Since it was desirable to continue shooting relatively large blasts for effective operation, it was recognized that larger storage facilities than had been in use would be needed for the liquid oxygen. Because of the difficulty of transporting and discharging large storage containers of efficient design, the better plan appeared to be storage and discharge of the liquid at the place of manufacture, and transportation of the filled soaking boxes to the blast. Present Liquid-oxygen Plant An experimental unit with a rated capacity of 75 liters per hour was erected during the latter part of the year 1926 to prove the effectiveness of L. 0. X. at this mine, its cost, and possible efficiency of large-scale storage of the liquid. With this experimental unit 200,000 tons of ore

Jan 1, 1928

By Ancel St. John

Defects in the interior of metal objects are troublesome to both manufacturer and user. For the former, they frequently increase manufacturing cost through the rejection of material when defects appear after considerable work has been done. For the latter, they often cause damage to equipment, personal injury, or loss of life when a part, which has passed all inspections and has been put in service, gives way because of a hidden flaw. Methods of testing that locate such flaws without subjecting the specimen to possible, if not actual, destl-uction are few; x-ray examination, whether fluoroscopic or radiographic, is one. Hitherto, however, x-ray examination has been restricted to objects of nearly uniform thickness and regular outline; the inspection of such articles as those shown in Fig. 1 has been inconvenient and unsatisfactory. This figure represents a group of 5/16-in. hexagonal-head machine bolts,

Jan 1, 1923

By A. L. Holmes

Significant technologic advances were made in open pit mining during 1973. The industry faced mounting problems on one front where expansion of stripping activities encountered enlarged public resistance and on another where manpower and materials were in short supply. These challenges, along with the challenge and opportunity to meet the increased demand for mining products including materials for energy production, placed a premium on technical developments and their application. The demands on technology also included the providing of facilities and methods to economically extract minerals from deposits of lower grade, lesser accessibility, and where other uses of land approached the value of its minerals. Detection of Failures in Slope Walls The Bureau of Mines has undertaken research directed towards providing a mine operator with the opportunity to take corrective action before a potential slide becomes a problem.

Jan 2, 1974

[NORTH AMERICA UNITED STATES ALABAMA AUBURN Sturm & O'Brien, Consult. Engrs. °Sturm, Rolland G. BESSEMER Granger, W. C. BIRMINGHAM Air Reduction Sales Crockett, John M. Amer. Cast Iron Pipe Co. Carter, Sam F., Jr. Donoho, C. K. Anderson Elec. Corp. Davis, Moss V. J. B. Clow & Sons Neptune, Maurice D. Connors Steel Div. °Sandelin, Robert W. Hayes Aircraft Corp. Ricketts, W. E., Jr. Willhelm, A. Clyde, Jr. McWaine Cast Iron King, O. H. Worthington, B. W. Shook & Fletcher Sup. Co. Gearhart, Thomas A. Southern Res. Inst. Dismukes, Edward B., Wheelahan, Edmund J. Thomas Foys Miller, Ralph M. Union Carbide Metals, Co. Brandler, Edgar A. U. S. Pipe & Fdry. Co. Clay, Donald H. Unaffiliated Berg, H. A. Caldwell, H. A. Gilmer, H. U. Harris, Thomas H. Templeton, J. B.]

Jan 1, 1961