Search Documents

By H. Biloni, G. F. Bolling

The microsegregation in tin specimens containing 0.2, 0.5. or 1 wt pct Pb has been studied m detail. The specimens were grown from the melt in a controlled fashion and exhibited a well-developed cellular substructure. In general, a severe microsegre-gation can be observed in all the photomicrographs presented. Some observations of special interest are: the distribution of a second phase, the presence of a eutectic in several forms, the evidence for dif- THE Smialowski or cellular substructure which forms during solidification has been extensively studied during the past decade.'* Many of the im- *Most references to the cellular substructure except for the last 2 years are reviewed by Winegard.' portant characteristics of this substructure, such as its occurrence and variability with growth conditions, its association with the phenomenon of constitutional supercooling, and its effect on dislocation production and mobility, have received quantitative fusion of solute in the solid, and the enhancement of segregation at a dislocation subboundary network ("striations"). On the basis of the metallographic observations, it can be deduced that the segregation observed is representative of the solute segregation produced during crystal growth. Some deductions are also made about the interplay of the two substructures, cells and striations, and about the mode of cellular growth. investigation both experimentally and theoretically. However, the concentration profile of the solute segregated during crystal growth has not been examined in detail. Tin crystals grown from melts containing various concentrations of lead have been most extensively studied. In a recent investigation of Sn-Pb alloys, Kramer et a1.2 were able to measure the effective solute distribution coefficient, k,, at the most advanced points of the solid-liquid interface, over a large range of growth conditions, finding it to approach the value of k,, the equilibrium distribution coefficient. As will be shown, this must lead to drastic segregation. Another recent study of several Sn-Pb alloys was made by Plaskett and winegard3 who investigated the variation of growth conditions

Jan 1, 1963

By R. W. Hyde, B. S. Old, S. E. Eaton

INTRODUCTION ONE of the most important problems facing the steel industry at the present time is that of maintaining at a minimum the sulphur content of many grades of steel where sulphur is known to have harmful effects on both quality and yield. The present outlook in this struggle to reduce the amount of sulphur in steel is rather gloomy since the sulphur content of the raw materials available in the United States is gradually rising, with little relief in sight. A flow sheet of sulphur in the steel process is shown in Fig I. The values used here were obtained by averaging coke oven and blast furnace data at No. 5 furnace in Cleveland and are considered typical for high top pressure practice. The sulphur evolved in the blast furnace top gas was obtained by difference and since the amount is relatively small, little significance should be attached to this particular value. From Fig I it is apparent, however, that coals used in the production of metallurgical coke represent by far the largest single source of sulphur in steelmaking. As an indication of the decrease in quality of these coals as regards sulphur content the weighed average annual sulphur analysis of the coals supplied to two different steel plants, since 1925, is plotted in Fig 2.1 The sharp rise since 1940 is strikingly apparent. Another indication of this trend is found in estimates of coking coal reserves. Thus in the case of Pittsburgh seam coals available in Allegheny, Fayette, Greene, Washington, and Westmoreland Counties in Pa. as of Jan. 1937 only 25 pct of the coal reserves would contain less than 1.50 pct sulphur after washing.2,3 Many of these lower sulphur reserves have been seriously depleted in recent years because of accelerated war demands. Still another demonstration of the increasing sulphur content of coals on a country-wide basis is found in a report by the Bureau of Mines4 which shows a steady increase in the sulphur content of coke made in the United States, It should be noted that this increase continues in spite of the wider use of coal washing in recent years. Sulphur occurs in coal in three forms, pyritic (FeS2), organic sulphur, and a small amount of sulphate sulphur (CaSO4), The sulphur is subsequently found in the coke in combination with carbonaceous material of unknown composition and as calcium and iron sulphides: In considering the general problem of sulphur elimination, the Republic Steel Corp. was interested in determining which, if either, of the two major forms of sulphur in coal contributes the greater portion of sulphur to the coke, Since the ratio of pyritic to organic sulphur varies widely in different coals, it was thought that if it could be shown definitely that the major part of the sulphur occurring in coke originates from one of the two major forms of sulphur in the coal, it would then be possible to select with confidence coal which, although high in total sulphur, would yield coke of fairly low sulphur content, Using the new

Jan 1, 1948

By F. V. Shallcross

Physical properties of thin films of CdS and CdSe formed by vacuum deposition onto glass sibstrates have been studied as a function of deposition and processing conditions. The crystallinity and surface features of CdS films were examined using electron microscopy and electron and X-ray diffraction techniques. The films were poly crystalline; the preferred orientation and crystallite size increased with film thickness, substrate temperature, and deposition time. The CdS films consisted primarily of hexagonal-phase material, in contrast to similarly prepared CdSe films which have previously been observed to contain mixtures of cubic and hexagonal phases. As-deposited CdS films showed no major dependence of Hall mobility on crystallite size or degree of preferred orientation. Hall mobility and carrier concentration in CdS and CdSe .films were measured at various temperatures; both parameters increased with temperature and yielded activation energies which depended on fabrication conditions. Surface-desorption phenomena and overcoating of the semiconductor with SiO affected the observed electrical properties significantly. THIN films of cadmium sulfide1,2 and cadmium sele-nide3,4 have been employed by various workers as semiconductors in the insulated-gate thin-film field-effect transistor, known as the TFT. These devices are most commonly made by vacuum deposition of all materials onto an amorphous substrate such as glass. A knowledge of the microstructure and electrical properties of semiconductor layers used in the thin-film transistor is essential in order to form a realistic model for the device and to improve its performance, reproducibility, and reliability. This paper will describe studies of the physical properties of vacuum-deposited CdS and CdSe films prepared under various conditions. Structural characteristics examined in- cluded phases present, crystallite size, nature of preferred orientation of crystallites, surface roughness, and structural homogeneity throughout the film thickness. Electrical properties measured were Hall mobility and conductivity and their dependence on temperature and ambient. Thin-film properties are affected by many fabrication parameters including purity and physical form of evaporant, deposition rate, film thickness, design and temperature of the evaporation crucible, geometry of the deposition chamber, nature of the residual atmosphere, composition and temperature of the substrate, and details of postdeposition processing. PREPARATION OF FILMS In this work the semiconductor films were deposited in a conventional oil-diffusion-pumped system with pressures in the 10-8 torr range. The CdS evaporant was obtained from the Eagle-Picher Co. as a high-purity coarse-grained crystalline powder; the CdSe was a high-purity sintered powder supplied by the Harshaw Chemical Co. The evaporation crucible was a resistance-heated molybdenum-wire basket coated with aluminum oxide and filled with a quartz wool plug at the top. The source to substrate distance was usually 10 cm. This region was enclosed by a Pyrex inner cylinder. The substrate was heated with an overlying Pyrex plate coated with tin oxide. The substrate temperature was controlled using a thermocouple attached to the lower side of the heater. This thermocouple was calibrated against another thermocouple attached to a dummy substrate and by observation of melting points of various metal films deposited in the system. The substrates were polished borosilicate glass plates and conventional glass microscope slides. Substrate preparation included cleaning with an ultrasonically agitated detergent bath followed by isopropanol-vapor de-greasing. Film thickness was measured interferomet-rically during and after deposition. STRUCTURE OF CdS FILMS Structural studies were performed on CdS films using electron diffraction, electron microscopy, and

Jan 1, 1967

By R. D. Begley, A. W. Khair

Introduction The technique being investigated here uses a physical mine model which consists of a plexiglass room-and-pillar model 11.4 x 11.4 cm (4.5 x 4.5 in.). It is placed at the bottom of a larger plexiglass box 25.4 x 30.5cm (10 x 12 in.). The box is then filled with a model material representing geologic overburden. Sand has been selected because of its deformability under gravitational forces. The mine model is capable of creating a cavity and induces movement on the surface of the model material. This surface disturbance can be measured using a photographic technique called holographic interferometry. This paper discusses results of an investigation of the possibility of generating subsidence criteria using physical mine models and laser holographic interferometry. Problem Statement Subsidence appears to be widespread in two states - Pennsylvania and Illinois - although serious subsidence is found in localized areas of numerous other states (HRB Singer Inc., 1977). The US Bureau of Mines estimates that more than 1618 km2 (400,000 acres) of urban areas are threatened by subsidence. Pennsylvania and West Virginia contain 57% of these threatened areas, with the remainder being spread out over 16 states (Johnson and Miller, 1979). Events of subsidence have been reported in urban areas, including Pennsylvania (Gray et al., 1977) and Illinois (Mahar and Marino, 1981). One location has observed three episodes of subsidence beginning in 1950 (Bruhn et al., 1981). These subsidence events all occurred over abandoned room-and-pillar mines. Some mines have been abandoned more than 50 years (Bauer and Hunt,1981) . Available research does not offer much on the problem related to time dependent subsidence, especially those associated with the failure of remnant coal pillars. The physical modeling technique developed at West Virginia University is capable of measuring both instantaneous and time delayed subsidence. Laser Holographic Interferometry Laser holographic interferometry, or holometry, uses the interference properties of laser light to measure small movements of objects. The object requires only optical access and no surface instrumentation. This technique is closely related to photoelasticity. Both techniques rely on the uniqueness of the light reflected off or through an object in any given state of stress. The entire measurement process is done remotely without any surface instrumentation and without using a camera. The interferogram is constructed and visual observation will yield fringes on all areas that yielded or moved. The displacement represented by one fringe was determined by Wilson et al. (1977) and is given by the relationship: [d ='1(1) 2 cos 8 where d = displacement of one fringe 6 = incident angle of laser light A = wavelength of light (632.8 x 10-9 meters for Helium-Neon lasers)] In summary, holometry is capable of detecting very small movements of objects under study. It is a very sensitive process that requires laser light and vibration free experiments. Experimental Program Lab Facilities The primary components of the facilities were the laser and the optical table. The light source was 50 milli-watt, Helium-Neon laser. The optical table was a granite slab weighing nearly one ton. All experiments were performed on the optical table. It consists of a large table sitting on air cells similar to car innertubes. Six air cells were placed on top of two layers of wood and Styrofoam. Figure 1 is a schematic diagram of the vibration free table. Even with these precautions, the experiments still had to be performed at night to reduce potential traffic related vibrations. Room-and-pillar mine models consisting of three different pillar sizes were constructed out of plexiglass. The models were designed to represent three different extraction ratios. Figure 2 shows the models. The extraction ratios were determined by the tributary loading concept (Peng, 1978). These models were the primary component of a seam extraction simulator. A schematic of this simulation device is shown in Fig. 3.

Jan 1, 1986

By D. E. Menzie, D. L. Dauben

This paper discusses the physical parameters involved in the slow flow of high molecular weight polymer solutions in porous media. The interacting effects of polymer properties and porous media properties on flow performance are considered. Experiments were conducted with the polyethylene oxides, with molecular weights ranging from 200,000 to over 5,000,000. Frontal advance velocities ranged from I to 30 ft/day. The porous matrix consisted of a flow cell packed with glass beads. Polymer solutions were characterized by viscosity and normal stress measurements. Under certain conditions, unexpectedly high flow resistance was observed. This behavior was observed to be a function of flow rate, pore size, polymer molecular weight and concentration. The polymer solutions exhibit "dilatant" flow behavior in porour media in contrast with the pseudo-plastic behavior in simple flow systems. A theoretical ex-planation of such behavior is presented. INTRODUCTION The use of polymers in the injected water of a waterflood increases oil displacement efficiency by reducing the mobility (k,/pu) of the driving phase. A reduced driving phase mobility results in improvements in the areal sweep efficiency and in the vertical coverage in stratified reservoirs. This mobility reduction may be achieved by a permeability reduction, a viscosity increase or by a combination of the two. Early attempts at increasing the injected water viscosity were not successful because of the poor economics involved. The use of such materials as glycerin, sugar or glycols to increase water viscosity was not economically feasible. Attempts in using certain naturally occurring polymers were not too successful because of the high polymer losses to the rock. A high molecular weight, partially hydrolyzed polyacry-lamide was introduced 3 years ago as a waterflood additive.',' Initial work by Pye' indicated that the presence of these polymers in dilute concentrations decreases the water mobility 5 to 20 times more than would be expected from measurements of the solution viscosity. Such an effect would be of obvious economic value since only a small polymer concentration would be required to accomplish a large reduction in water mobility. This research was designed to study the basic flow mech anisms of polymer solutions in porous media. The interacting effects of polymer properties and porous media properties on flow performance are considered. This study indicates some of the conditions under which these interactions can lead to significant mobility effects. is valid only for Newtonian fluids. For polymer solutions and other non-Newtonian fluids the equation must be modified to consider that viscosity is a variable quantity. Modification of the Darcy equation to include non-Newtonian effects has been the subject of several recent investigations."" The modifications generally adopt a rheological model. such as an Ellis or Dower law model. to Dorous media by defining some characteristic channel radius. Most of these studies showed the porous media flow behavior to be predictable from viscometric data. Investigations involving the flow of high molecular weight polyacrylamide solutions through cores have generally encountered the high flow resistances reported previously by Pye. This high flow resistance has generally been attributed to an in-depth permeability reduction, as evidenced by a reduced permeability to water which has displaced polymer solution from the porous media. Marshall and Metzner" report high flow resistances, which they attribute to viscoelastic effects. In this paper, the effects of polymer molecular weight, pore size, flow rate and concentration are considered. The polymers used are the polyethylene oxides known as Poly-ox. This class of polymers was used because of its availability in a wide range of molecular weights and because of its known ability to propagate well through porous media. THEORY PHYSICAL PROPERTIES OF POLYMER SOLUTIONS The polymer molecule dissolves in water by means of hydrogen bonding, but retains some of its own structural identity while in solution. Nonionic polymers, such as polyethylene oxide, are generally considered to have a random coiling configration. This type of molecule has the ability to "sequester" or hold a large volume of solvent within its coils in a manner similar to that of a sponge. The random coil is easily deformed and under an applied stress

By J. Campbell

Various models are discussed for the evaluation of the negative pressures which may occur in solidifying materials which exhibit various deformation modes: elastic-plastic, Bingham, viscous, or creep flow. The inadequacy of the previously proposed elastic-plastic solution for solidifying metals is revealed by comparison with the more reliable creep results which are given graphically for aluminum, copper, nickel, and iron. The maximum tensions experienced in the liquid phase of solidifying spheres ranging in size from large castings to submicron powders are in the range from —10' to —105 atm for these metals. THERE has been much recent interest in the negative pressures associated with the volume change on solidification and in the possibility of the occurrence of cavitation. Considering the freezing of a highly supercooled liquid, an attempt to evaluate the stresses in the liquid ahead of the rapidly moving solidification front has been made by Horvay1 on a microscale and by Glicksman2 on a macroscale. In a casting of a wide freezing range alloy, the pressure differential due to viscous flow of residual liquid through the pasty zone has been discussed by Piwonka and Flemings,3 In a previous publication4 the author has attempted to estimate the negative pressure occurring in the residual liquid of a spherical casting, employing an elastic-plastic model to describe the collapse of the solidified shell under the internal tension. An earlier model assuming a rigid shell was shown to be inaccurate by many orders of magnitude. The elastic-plastic model is critically reviewed here, and other models are developed which are thought to be more closely related to metals and other materials near their melting points. The spherical geometry (Fig. 1) is chosen because the highest shrinkage pressures would be developed, although the analyses are readily adaptable to cylindrical geometry. A parallel sided casting experiences little internal tension because of the relatively easy dishing inward of the sides. (This commonly observed phenomenon has previously been attributed solely to atmospheric pressure.) Furthermore, small regions of confined liquid in a large solidified volume of a casting approximate reasonably well to spherical geometry. ELASTIC-PLASTIC MODEL The author has shown4 that as solidification proceeds the internal hydrostatic tension builds up until the elastic limit of the shell is exceeded. At this point the internal pressure is closely -2Y/3. Subsequently a plastic zone spreads from the inner surface toward the outer surface of the shell. When the whole casting is deforming plastically a rather more generalized analysis taking account of the externally applied pressure PA + 2y/b gives the internal pressure as: P = Pa + 2y/a + 2ys/b - 2 Y In(b/a) [1] The 2y/a and 2ys/b terms result from the tendency of the liquid-solid and solid-vapor interfaces to shrink, reducing their energy, and thereby helping to collapse the solid phase and compress the liquid phase. The 2y/b term would be important only for powders. The last term arises because of the plastic restraint of the solid, resisting collapse and so effectively expanding the residual liquid. From Eq. [I] it is easily shown that there is a minimum in the pressure at the radius amia= y/Y [2] which is of the order of 103K for the metals aluminum, copper, and iron, and corresponds to the minimum pressure Pmin = 2 Y[l-ln(bY/y [3] The results of a fully worked out elastic-plastic solution are given in a previous reporL4 The main criticism which may be leveled at this analysis when applied to metals at their melting points is the strong dependence of the yield stress on the strain rate. The strain rate varies with both solidification conditions (e.g., whether chill-cast or slowly cooled) and during solidification, as is indicated in the following section. Thus an appropriate choice of Y is very arbitrary. Before proceeding to a discussion of models which are strain-rate-dependent, it is necessary to evaluate the strain rate as a function of the rate of solidification. SOLIDIFICATION RATE Various empirical relations have been deduced5 for the rate of thickening of the solid shell by pour- out tests on partially solidified spheres. These, however, are unsatisfactory for our purposes since they become very inaccurate when the liquid core is very small. A theoretical approach is therefore necessary, and some solutions are set out below. Making the assumptions of constant surface temperature of the casting during freezing, no superheat, and a material freezing at a single temperature, Adams8 deduces the approximate solution: which becomes when b » a: Employing a semiempirical approach vallet6 finds:

Jan 1, 1969

By R. T. Walker

GROUND waters-hot or cold-containing small amounts of the more common earth acids, such as carbonic acid, silicic acid, hydrogen sulfide, sulfurous acid and sulfuric acid, have only a very limited "solvent effect on dominantly siliceous rocks, whether of igneous or sedimentary origin, but in limestone they often form extensive cavities; and such "limestone caves" are the only openings of considerable size and continuity in rock formations that do not owe their existence directly and almost wholly to dynamic action. Limestone caves such as are developing at the present time must have been formed in all past geological ages in which limestone beds existed and where suitable conditions for the development of such caves prevailed; hence it would seem a reasonable expectation that, in the course of geological history, a certain number of ancient limestone caves must have been utilized as channels for the passage of mineralizing solutions, during portions of their course, at least, and that, in consequence, orebodies must have been deposited in such caves. Such a conception is not novel; it was proposed many years ago, but its possibilities, as explaining certain types of ore deposits, have been rather lost sight of in the development of the theory of the metasomatic replacement of rocks by minerals. It is the purpose of this article to assemble evidence to show that many of the orebodies found in limestone beds have been deposited in pre-existing caves; to discuss the criteria whereby such orebodies can be distinguished from others which have been formed along fissures and fracture zones traversing limestone, by the more common method of metasomatic replacement, analogous to orebodies in other formations; and to describe certain orebodies-particularly the "ore channels" of the Tintic district, Utah-as illustrative of the principles discussed. Limestone caves may be divided into two classes: those formed by cold, descending surface waters, which emerge again at some lower elevation as cold springs; and those formed by hot, ascending waters of deep origin or circulation, which attain the surface as thermal springs. Although these two classes are similar in many respects, there are certain characteristic and inherent differences whereby they can usually be distinguished.

Jan 1, 1928

By W. L. Fink, L. A. Willey

This paper is the nineteenth of a series from the Aluminum Research Laboratories, presenting the results of the investigations of equilibrium relations in aluminum-base alloys made from electrolytically refined aluminum. In previous papers equilibrium relations have been determined and correlated for 12 binary systems. Equilibrium relations have also been determined for portions of the aluminum corners of three ternary systems (aluminum-iron-silicon, aluminum-magnesium-silicon and aluminum-copper-magnesium). The object of the present paper and those to follow is to increase our knowledge of the aluminum corner of the more important ternary systems. In 1926 Dix and Keith † suggested a new method for designating the phases encountered in alloy systems. The system has been used to a very limited extentl,2,3 The system has since been slightly modified and will be used in this and future papers. In the system as modified, a phase is designated by placing in parentheses the chemical symbols of the elements essential to the formation of that phase. The symbols in the parentheses are separated by dashes in order to clearly distinguish them from a chemical formula. Elements that are not necessary to the formation of the phase in question, but which may be present in solid solution, are not indicated in the designation. If two or more phases would have the same designation according to these rules, they are distinguished by prefixing Greek letters, and are definitely identified by X-ray diffraction patterns. Previous Investigations The solid solubility of magnesium in aluminum has been well established by the work of Dix and Keller4, Schmid and Siebe15, and Saldau and Sergeev6. There is no agreement as to the composition of the magnesium constituents at the aluminum end of the binary aluminum-magnesium system. Hanson and Gayler7 report Mg2Al3; Boyer8 found that the alloy

Jan 1, 1937

By S. E. Bronisz, Dana L. Douglass

a Uranium was deformed by cold rolling, and the effects of this plustic deformation on the microstruc-ture of the metal were observed by the technique of transmission elecbon microscopy. The recrystalli-zation of selected cold-wmked samples was also studied by this method. The samples were prepared for examination by electrolytic thinning in a standard metallographic electrolyte which has not been previously reported as being used in producing thin foils of uranium. The microstructural changes observed in the a uranium were generally similar to those seen by optical microscopy. The changes in the microstructure of a uranium following cold work and recrystallization treatments have been the subjects of several studies employing optical and X-ray techniques.12-19 These studies indicated that twinning was the redominant mode of deformation at room temperature20 and that the regions of high energy associated with the deformation twins were preferred sites for the initiation of recrystallization.15,18, Recently several workers have prepared thin foils of uranium suitable for examination by transmission electron microscopy.'-lo The foils thus prepared have been used to study fission fragment damage; a particular dislocation reaction,' and gas precipitation." At this laboratory the microstructural changes occurring during the cold working and recrystallizing of a uranium samples have been studied by using transmission electron-microscopy techniques. The foils used in this work were electrolytically thinned in a polishing bath not reported previously in the literature as being used for this purpose. EXPERIMENTAL PROCEDURE The uranium used in this investigation was depleted a uranium sheet 4 mils thick. The results of a spectrochemical analysis of this material are shown in Table I. The as-received uranium was cut into strips, 1 in. wide by 5 in. long, and annealed in vacuo at 600°C for 2-1/2 hr. The resulting microstructure consisted of relatively uniform, equiaxed grains having diameters of 10 to 50 p. Cold Working. The cold-worked samples were prepared by rolling several of the annealed uranium strips to various thicknesses. The strips were reduced 3.5 ± 0.5, 6.0 ± 0.6, 10.0 ± 0.5, 19.5 ± 1.0, and 28.5 ± 2.0 pct in thickness. It was not possible to achieve these reductions with a single pass through the rolling mill, so the strips were turned end for end during the rolling procedure. The cold-rolled strips were stored in dry ice until samples from them could be thinned and examined (within 24 hr after rolling). Annealing. The samples used in studying the re-crystallization behavior of a uranium were obtained by annealing sections of the strips which had been reduced 10.0 and 28.5 pct. These samples were sealed in evacuated Pyrex capsules and were annealed in a tube furnace at temperatures from 200" to 600°C and for times from 1/2 to 2 hr, see Table l. Thinning: The samples from the rolling and heat treatments were prepared for examination in the electron microscope by electropolishing in a bath composed of 25 g chromic acid, 133 ml glacial acetic acid, and 25 ml water. This electrolyte has been used and recommended for preparing specimens for optical metallography It was necessary to mask the edges of the sample with a stop-off paint in order to prevent preferential attack in these areas. The paint used was made by dissolving polystyrene in benzene. The electrolytic cell consisted of a cylindrical stainless-steel cathode placed in a beaker containing the electrolyte, with the sample as the anode positioned at the cell axis. The temperature of the electrolyte was held below 15°C by cooling with liquid

Jan 1, 1963

By Robert Lewis

THE Utah coal field to which the name Book Cliffs is applied runs in a northeast direction from Mt. Hilgarde, in Sevier county, along the escarpment of the Wasatch Plateau to the vicinity of Castle Gate, thence southeast along the Book cliffs, which lie to the north of and generally within sight of the Denver & Rio Grande Railroad,. to the Colorado line. The Book cliffs form the southern escarpment of the West and East Travaputs Plateaus, and vary in height from 2,000 to 6,000 ft. At the base of the Wasatch and Book Cliffs escarpments is a broad plain known as Castle valley. The coal beds outcropping in the escarpments along this valley are worked on the largest scale of any in the State, and this particular area is known locally as the Castle Valley coal field. Geology The Book cliffs are capped by the Tertiary-Eocene-formation, consisting of varicolored shales; buff sandstone, conglomerate, and subordinate thin beds of limestone. Different sections show diverse stratigraphy. This is mainly the Wasatch formation, and lies unconformably upon the rocks of the Upper Cretaceous. Fig. 1 is a generalized section of the rocks of the. Book Cliffs field. The Mesaverde formation contains the cliff-making rocks of the Book cliffs, and is composed of massive sandstone interbedded with sandy shales and beds of coal and carbonaceous shale. The sandstone has greater resistance to erosion and the formation is characterized by escarpment ledges and cliffs. The shale is commonly sandy and is drab in color, but where it is associated with the coal it is usually carbonaceous. The sandstone is generally buff, though occasionally it is white, and in places red. The bedding ranges from thin to massive. In the lower part. of the formation the sandstone is red in

Jan 7, 1914

By P. V. Faragher

A METAL or alloy finds its place in commerce in proportion to its ability to serve certain purposes better and more economically than other materials. While there is some overlapping of the fields of application of the various metals under discussion in this symposium, each one has its uses for which it is especially adapted. While aluminum is the most recent of the metals to enter the field, the development of the industry has been based on its peculiar properties, by virtue of which new uses for non-ferrous metals have been created. There has been substitution of this new metal for other members of the group but there has been a far greater development in entirely new fields. In common with the other non-ferrous metals, aluminum is resistant to atmospheric corrosion. It also withstands the action of many of the common chemical reagents, strongly alkaline substances being the notable exceptions. The outstanding properties on which the application of aluminum is based are its low specific gravity and its ease of fabrication into the forms in which it is used. It is noteworthy that this property of specific lightness is retained in all the commercial aluminum-base alloys. This statement does not apply to aluminum bronze; this is more properly a copper-base alloy, since aluminum enters into its composition to the extent of only about 10 per cent. None of the commercial casting alloys of aluminum has a density exceeding that of the parent metal by more than about 10 per cent., and some are actually lighter. In the so-called "strong alloys" of aluminum in which strengths comparable to that of mild steel are developed by heat treatment, the greatest increase in density is only slightly more than 3 per cent., and one of these, also, is lighter than aluminum. This property of lightness combined with the desirable mechanical properties of the alloys, makes aluminum especially suited for parts of moving assemblies where saving in power, as well as a decrease in stresses resulting from inertia and vibration, are of importance.

Jan 1, 1928

By V. A. Josendal, J. W. Wilson, B. B. Sandiford

Two radioactive tracers have been tested as a means of determining core saturation in multiphase flow studies. Cesium chloride was tried as a water-phase tracer, but complications in its use in low permeability cores resulted from sorption of cesium by the core or water-wet pads. IodoI3'ben-zene proved very satisfactory as an oil-phase tracer. The synthesis of iodobenzene from the sodium iodide as received from Oak Ridge is simple and direct. The tracer is insoluble in water and there was no evidence of sorption by any of the core materials used. use of the method to determine saturation profiles during capillary and dynamic desaturations and relative permeability measurements on oil-water and oil-gas systems is described. Comparisons of the dynamic and capillary methods of relative permeability determination were made using the tracer to check core saturation and saturation distribution. Other experiments are also described in which mobility of the oil phase at various saturations was measured by displacing labeled oil by flowing inactive oil. Similar experiments were made using water labeled with cesium 134. INTRODUCTION To be fundamentally sound. any laboratory method of determining relative permeability must meet, among others, the following requirements: (1) the core saturation between the pressure taps must be uniform, and (2) there must be uniform pressure difference between the phases in the region between the pressure taps. In practice it may eventually be shown that appreciable departure from either or both of these conditions may be permitted without introducing sensible error. but the magnitude of such error remains to be established. There is need then for methods of saturation determina- tion which will determine the saturation profile in a core as well as the overall average saturation given by the gravimetric or material balance methods usually employed. Methods which have received consideration include resistivity, X-ray absorption, gamma ray absorption, neutron diffraction, and radioactive tracers. The resistivity method has use in the determination of profile, but needs checking by independent means.' The X-ray method has been used successfully, but requires elaborate equipment and calibration.23 4 At present gamma ray absorption is practical only for very large cores. The neutron methodo does not appear adaptable to measurement of saturation variations in short cores since it is a scattering method. Russell, Morgan and Muskat' employed radiovanadium in a study of the mobility of interstitial water. Coomber and Tiratsook used radioiodine as an oil-phase tracer and measured profiles in unconsolidated sand packs. ADVANTAGES OF RADIOACTIVITY METHOD A thorough discussion of the theory of radioactive tracers and the technique of using them to study the movement of fluids in sands is given by Coomber and Tiratsoos and need not be detailed here. The method requires less equipment than the X-ray method; the counting problem is similar, but the generation and regulation of the radiation, which is a major problem in the X-ray method, is not required in the radioactivity method. In the X-ray method it is customary to add up to 20 per cent of absorber, usually an iodine compound, to the phase to be labeled. while in the radioactivity method a mere trace is sufficient. A possible disadvantage of the radioactivity method is that a disproportionate amount of the activity comes from the portion of the core nearest the counter, whereas the X-ray gives a true average saturation in the region traversed by the beam. 011 the other hand, this characteristic of the radioactivity method renders it peculiarly adaptable to study of certain types of radial variations in saturation. As with the X-ray method, a tracer may be added to either the oil or water-phase. An oil-phase tracer is more generally useful. however. since it permits work on oil and gas in the

Jan 1, 1952

By M. C. Dow

INTRODUCTION BELT conveyors generally are conceded to be the most economical method yet devised for the transportation of large quantities of bulk materials within plants. Belts are coming into greater use for transportation over long distances and are replacing other forms of long-haul conveyance. It is not the intent of the writer to comment on the design of belt conveyors, but to offer some suggestions for improvement in the operation of conveying belts, based on many years experience with belts in several stonecrushing plants. It is the contention of this writer that opportunities for improvement not fully realized by most operators exist in many plants and that a study of the individual conveyors can result in lower unit belt costs. GENERAL RELIABILITY It is the fool-proof nature and general reliability of the belt conveyor that is responsible for its neglect. Even when abused, a belt will carry large tonnages and last a long time, often outlasting the personnel responsible for its care. Some operators look upon the purchase of a new belt as an expensive outlay every so many years, rather than a constant and steady cost amounting in belt wear alone to several dollars every operating day. This belt wear for all conveyors in one stone-crushing plant known by the writer costs 1 1/2 cents per ton or $12 to $15 per hour, based on the present cost of belt replacements. The fact that these replacement costs are double those of prewar quality emphasizes the necessity of improving the conditions that make belts wear out. Some of those conditions are the responsibility of the conveyor designer, and if a serious original error has been made, this handicap cannot be overcome by the operator. If the belt is too narrow, too steep, or too fast for good loading, the operator finds that he has an inherently expensive belt. The other factors that decrease the life of a belt are more or less under his control. The two factors of most importance are the loading conditions and the alignment. Most of the cover wear and carcass cutting occurs at the loading point and if the alignment is not good under all conditions, edge wear or damage may result, Fig I. LOADING THE BELT It is difficult to load a belt in an ideal manner; that is, to flow the material on the moving belt at a steady rate, without impact, without turbulence, and with a velocity equal to and in the same direction as the belt. An inclined belt is especially difficult to load and particularly when its speed is over 300 or 350 fpm. Inclined conveyors require longer skirt plates to prevent spillage until the load settles. It does not seem reasonable to expect an inclined conveyor to carry the same load as a horizontal belt of the same width and speed, because of the difficulty in loading

Jan 1, 1947

By H. Rush Spedden, A. M. Gaudin

IN the belief that a critical study of its operating problems might be a sound investment, the Cuban American Manganese Corporation initiated an ore-treatment research in cooperation with the Massachusetts Institute of Technology. One of the early objectives of this research naturally became the relationship of the microscopy of the Cuban ores of the Corporation to their flotation treatment. The operations in Cuba have already been described by F. S. Norcross, Jr.7 and the laboratory study of manganese oxide flotation goes back a number of years .4 Broadly speaking, the difficulties encountered in the flotation of manganese ores are that the consumption of reagents is extremely high, the concentrate contains more silica than is desirable and the tailing losses are relatively high. An appreciable betterment on any of these scores would achieve a definite betterment in costs, quantity of minable ores, and quality of product. The microscope study discussed in this paper was made on samples from the Quinto mine, from the Ponupo mine, and from mill products at various stages of passage of the ore through the mill. The writers have had access to Company records and in particular to the petro¬graphic studies made on thin sections of ore by the late Professors R. J. Colony and Philip Krieger, of Columbia University. They acknowledge their debt to both of these men for the help derived from the reports. Manganese oxides are black, friable, smudging. It is, therefore, very difficult to judge operations by inspection. The mineralogy of manganese compounds seems to be confused, and the authors believe that many more minerals have been described than actually exist. Much of this difficulty is due to the prevalence of the structural conditions that will be discussed further in this paper; namely, the porosity and the friability of the ores, and the extremely intimate association of minute manganiferous mineral crystals with impurities of various sorts. By all odds the most important manganese mineral in Cuba is the one that in this paper is called "psilomelane." The name "psilomelane" has been used in so many different ways that the choice of it for this ore may not be approved by all. However, it seems to be the best under the circumstances. This mineral accounts for about 97 per cent of the manganese in the ores of the Quinto and Ponupo mines and in the mill feed. The remaining odd 3 per cent consists mostly of pyrolusite together with minor amounts of other manganese oxide minerals. DESCRIPTION OF PSILOMELANE Aggregate Structure In grains or lumps, psilomelane has a characteristic fibrous appearance and seems

Jan 1, 1942

By Robert Hoy

If the reader finds that the basic information in a commodity chapter is insufficient, he can consult the appropriate sources in this chapter to find more detailed or more up-to-date information. In these days, technology develops so rapidly that this 4th edition will be somewhat out of date even by the time it is distributed. A comparison of this edition with the 3rd edition (1960) of Industrial Minerals and Rocks will clearly demonstrate how rapidly the scene changes. One of the best sources of new information, of course, is attendance at technical meetings. For example, the papers presented at the national and sectional meetings of AIME usually discuss new developments in the respective divisions of the society. Frequently this information is available in Preprints. In addition some are printed in Mining Engineering and/or the Transactions of the Society of Mining Engineers of AIME. Furthermore, other professional and trade journals contain articles pertinent to the field. A journal introduced in 1967, Industrial Minerals, published by the Metal Bulletin, Ltd., London, is an excellent source of information. The Mining Journal, Ltd., also in London, publishes a weekly journal, a Mining Magazine (monthly), and a Mining Annual Re- view. The latter covers the field from three aspects: (1) by commodities, (2) through technical developments, and (3) geographically. Other useful magazines and periodicals include Engineering and Mining Journal, Pit and Quarry, Rock Products, and World Mining, all published in the United States. In addition many new books related to industrial minerals have been published since the 3rd edition of Industrial Minerals and Rocks. Most of these, of course, are included in the bibliography of each chapter in this volume. Another excellent information source is the proceedings of the Forum on Geology of Industrial Minerals. This group, which held its 11th annual meeting in 1975, is sponsored by a state geological survey or another mineral agency on a rotational basis. The proceedings have been published by the various sponsors and are available as indicated in Table 1. Two major sources of basic industrial mineral and rock data in the United States, and also a good source for many foreign countries, are the U.S. Geological Survey and the U.S. Bureau of Mines. The two agencies publish many reports and maps on a variety of geo- logical and mining subjects. In addition, each agency has an indexed list of all their publications with a free service announcing new publications. (New Publications of the Geological Survey, U.S. Geological Survey, Washington, D.C. 20242) and New Publications-Bureau of Mines, Publications Distribution Branch, U.S. Bureau of Mines, 4800 Forbes Ave., Pittsburgh, Pa. 15213). The U.S. Bureau of Mines (USBM) publishes annually Minerals Yearbooks which provide statistical data on mineral products including production, consumption, imports and exports, as well as information on new developments. Another very useful USBM series is called Mineral Facts and Problems. Editions were published in 1960, 1965, and 1970. Three other major series of publications by the Bureau are Information Circulars, Reports of Investigations, and Mineral Trade Notes. The latter is particularly good for news of foreign developments. A new Professional Paper No. 820 of the U.S. Geological Survey, 1973, summarizes data on the mineral resources of the entire country. The USGS, in cooperation with USBM, other Federal and various state agencies, has also prepared summary reports on mineral and water resources of given areas which include

Jan 1, 1975

By Frederick N. Rhines, Robert F. Mehl

IT has been shown elsewhere1 that the data on the rates of diffusion in solid metals are fragmentary and in many cases unacceptable. As a result, relatively little is known concerning the factors determining rates of diffusion and the variations in these rates with temperature. The first form of Fick's law (equation 1 below), ‡ in which the diffusion coefficient D is assumed invariant with composition, has been recognized for many years as only an approximation. The differential equation representing the second form of Fick's law (equation 4 below) has only recently been integrated by Matano,2 and unfortunately only in cases where a full diffusion-penetration curve (concentration-distance curve) has been obtained can the Matano solution be applied. The proper analysis of diffusion data is thus confined to the data of Grube and Zedele and of Zedele.§ These data are essentially for one temperature alone and do not furnish any information on the variation of the activation heat of diffusion, Q, with concentration: no information exists on the variation of Q with concentration within a singles olid solution field. 11 Much of the argument concerning the properties of metals that determine D and Q has been drawn from data in which variations of the quantities with concentration are unknown, for these data have been taken from experiments that could not furnish this information. Speculation concerning the properties of metals that may be effective in determining D and Q on the basis of data in which the chosen D and Q values are averages over wide concentration ranges of values at particular concentrations, ranges often of 100 per cent, is likely not to be fruitful.

Jan 1, 1938

By Shiro Ban-ya, John F. Elliott, John Chipman

The activity of carbon in Fe-C austenite at 1150°C has been determined for concentrations up to about 2.1 pct C using the equilibrium: C + COz = 2CO; equations have been derived expessing the activity as a function of carbon content on the basis of twelve mathematical models. Several of these represent the data satisfactorily. ACCURATE information on the thermodynamic properties of austenite in the binary system Fe-C is needed as a basis for studies of transformation and precipitation in steels of all sorts, alloy as well as plain carbon. The many attempts to approach this problem through statistical thermodynamics require sound and dependable experimental data in order to evaluate the several models which have been suggested. In this paper we are concerned with the experimental determination of the activity-composition relation in austenite at the temperature of its widest range of stability, approximately the eutectic temperature (1153°C). Accurate investigation of the activity of carbon in austenite may be said to have begun with the work of Dunwald and wagner.' A more detailed study was carried out by R. P. smith2 on the two equilibria: More recent work on these two equilibria has been reviewed by Chipman,3 who pointed out the experimental hazards associated with studies of Eq. [I]. Studies of this reaction involve rather small values of the ratio these are susceptible to errors due to traces of moisture in the apparatus according to the reaction: Ellis, Davidson, and Bodsworth4 evaluated K, for their experimental temperatures and used desiccants to control water vapor pressure. While they were able in this way to obtain consistent values for K1 it cannot be said that all of the uncertainties of the method have been overcome. Results by both methods reported by Schurmann, Schmidt, and wagener5 appear to be consistent except at very low carbon content. Reaction [2] was employed in the experimental work reported here. It is to be recognized, however, that it is not applicable to projected studies of certain alloy steel compositions involving stable oxide-formers.

Jan 1, 1970

By J. Parke Channing

These days of great industrial and social problems in America produce many suggested solutions and great changes. The practical engineer and employer of labor views these problems differently from the labor leader or the social reformer, but as never before he is sincerely interested in solving them in a way that will be just to all. The inevitable tendency of the day is toward "industrial betterment," " safety," '(industrial education," " efficiency," and the many other things which have become so familiar to progressive employers. There is no longer any question that these things are worth while from both the human and economic standpoints. They "pay" in dollars and cents. The very center of final success in improving conditions and increasing the efficiency of workingmen must be the spirit of fairness and a knowledge on the part of the employer of how to deal sympathetically and intelligently with his employees. Every progressive employer knows how greatly he desires foremen, superintendents, managers and others who possess these qualities. On the other hand, we are all familiar with serious mistakes made by young graduates of engineering schools who have had no opportunity to develop these qualities, and who have no real appreciation of the worth of the workers. Indeed, one wonders whether much ill-feeling, labor difficulties, and many strikes could not be avoided if such men had the right attitude. Is there any way of remedying this condition? If this particular difficulty can be solved, if these young engineers, many of whom are our coming leaders of industry, can be given the right perspective and the right understanding of these other problems in addition to fair, sympathetic methods of handling men, many of our other problems will be solved—not at once, but gradually and permanently, as these men make good and become influential in paths of industrial righteousness and industrial peace. Many progressive employers of to-day have enlarged their own perspective and realize the great importance of enlarging the perspective of those who shall follow them. How can it be done? For seven years a movement has been making

Jan 1, 1915

By M. R. Geer, J. D. Davis, H. F. Yancey

ALTHOUGH the mechanical cleaning of coal is carried out at plants on the surface, preparation is actually begun at the face in the mine. Here the character of the coal and the amount, character, and distribution of the impurities within the bed may be seen. Blasting methods, dust-allaying procedures, location of mining cut with respect to bands of impurity, and the practice of discarding segregated impurities underground, all have an important bearing on the successful operation of surface cleaning units. The most important single characteristic of both coal and its associated impurities from the standpoint of cleaning is specific gravity. Other characteristics related in one way or another to the preparation , of coal are rank, petrographic composition, structure and hardness, and friability. These and still other coal properties are discussed in the first section of this chapter and impurity characteristics in the second. COAL CHARACTERISTICS RELATED TO PREPARATION Rank As a result of work done over a period of several years by committees of the American Society for Testing Materials and the American Standards Association, standard specifications are now available showing the 'classification of coals according to rank and quality of grade.' The term "rank" expresses the degree to which the original coal-forming material has been changed by metamorphism through successive stages from peat to anthracite. Table 1 shows the classification of coals according to rank as devised by the committees of the organizations mentioned. The basic scheme of classification for the higher-rank coals is according to

Jan 1, 1943

By P. R. Gage, R. W. Bartlett

At high temperatues and reduced oxygen pressuves, molybdenum silicicles oxidize to form SiO(g) vathev than a passivating SiO2 film. This is a sevious problem for low-pressure applications of sili-cide-coated rejvactory tnetals. As oxiclalion pvoceeds, the higher oxidntion potential of silicon initially suppresses oxidation of molybdenum and silicon is depleted near the surface. Eventually, silicon depletion causes secondary passivation (SiO2) mid an active to passiue transition in oxidntion behavior at moderately low pressures. At very low pressures, silicon depletion continues until steady-state oxidation of both silicon and rnolyhdenum can proceed at rates propovtional to their initial stoicliiorrzetvies. Ohsel-vations of 'oxidatiou-rate belzcriliov at temperatures from 1101° to 1700°C and oxygen pressures from 10-7 to 1 at in were made using thermogravimetn'c, X-ray diffraction, and elect?*on-rtric?ro/,vobe techniqrres. The experimental results are in good agreement with calculated lirnits for the various types of behavior that were based on tlievtnochernicnl atzd dffusion rate data for the Mo-Si system. A protective oxide film normally forms during the oxidation of elemental silicon. However, at elevated temperatures and reduced pressures this film is not present and oxidation is rapid. wagnerl has shown that this behavior occurs because SiO(g) is more stable than SiO2. The behavior of the silicides at high temperatures is similar but more complicated. Molybdenum and several silicide compounds are involved and the chemical activity of silicon, or the equivalent silicon vapor pressure, can vary considerably in these phases. Also, diffusion in the silicides resulting from reactions in which a higher silicide is reduced to a lower silicide, or molybdenum containing dissolved silicon, must be considered. EXPERIMENTAL AND ANALYTICAL METHODS Isothermal oxidation experiments were conducted using hot-pressed MoSi2 and Mo5Si3 wafers. Each experiment was conducted at a fixed oxygen pressure by controlling the flow of oxygen in and out of the furnace chamber. Most of the experiments were conducted in a molybdenum-wound tube furnace. Special construction features, including use of a high-purity dense A12O3 refractory tube, permitted operation in high vacuum to 1500°C. Higher temperatures could be obtained at higher working pressures and with a sacrifice of tube lifetime. Temperature was measured with three Pt 6 pct Rh/Pt 30 pct Rh thermocouples and controlled with a proportional controller. Weight changes were monitored with a quartz spring balance. The few experiments, at higher temperatures and low pressures, were conducted in a cold wall vacuum chamber using induction heating with direct susceptance of the sample. Because of the variable levitation effect of the induction coil on the sample, weight changes could not be monitored continuously in these experiments. All samples representing both experimental methods were weighed before and after oxidiation and examined with a microscope and analyzed by X-ray diffraction. The analytical treatment assumes equilibrium at interfaces and uses existing thermodynamic data. For convenience, equilibria are expressed as chemical potentials or as vapor pressures of the gases involved. The resulting differences in equilibrium vapor pressure between adjacent interfaces and between the surface and external atmosphere drive diffusion processes in the solid and gas boundary film, respectively. These diffusion processes govern the rate of oxidation. A bibliography of the sources of thermochemical data for the reactions pertinent to the Mo-Si-O system is given in Table I. Reactions are listed with the sources of free-energy data referenced. Since all of these reactions involve one or more gas species, usually oxygen, a plot of the product-gas chemical potential, -RT In Pg, vs absolute temperature for each reaction is given in Fig. 1. These curves can be used to determine equilibrium vapor pressures or to compare the stability of different compounds in the various gases: O2, Si, SiO, and Moo3,. The data of Table I and Fig. 1 were used to determine the analytical results presented in this paper. EXPERIMENTAL RESULTS The weight changes for three MoSi, samples oxidized at 1500°C are plotted against time in Fig. 2. The treatments were identical except for the indicated variance of oxygen pressure and each curve represents one of three characteristic types of behavior that were observed. The upper curve is an example of passive oxidation, which is defined as

Jan 1, 1965