Search Documents

By Gill L. F, Gleeson HB

This paper describes the development of a Computer Aided Design and Drafting based mine planning system in the State Electricity Com- mission of Victoria. The system combines a commercially available CADD system with a commercially available mining/geological package. The methodology used in the establishment of the combined system, the fea- tures of the system and the current status of development are discussed.

Jan 1, 1989

By Thornton D, Esterle J, La Rosa D

Control of blast fragmentation has a significant impact on coal mine profitability. Two approaches for the characterisation of coal blastability, particularly in terms of fines, are presented. Both approaches were implemented for the predictio

Jan 1, 1998

By Bailey S, Avraamides J

Laboratory-scale experiments were conducted in a mechanically stirred aeration vessel to determine the rusting abilities of aerated water in the presence of various catalysts compared to the industrially used ammonium chloride. The catalysts used were tartaric acid and citric acid, firstly by themselves, and then in later experiments mixed with ammonium chloride. From these experiments it was found that leaching of iron from reduced ilmenite in the presence of either tartaric acid or its sodium salt was much slower than in the presence of ammonium chloride. Citric acid or its sodium salt also give a slower rate of leaching than the ammonium chloride system, but citric acid and its sodium salt mixed in equal proportions produced a rate of leaching approximately twice as fast as the standard ammonium chloride system. When tartaric acid was mixed with ammonium chloride the leaching rate was found to be equivalent to the leaching rate of the same amount of ammonium chloride alone, thus indicating that tartaric acid made no contribution to the leaching in this svstem_

Jan 1, 1996

By Koh P. T L, Varnas S. R

Fluid flow, heat transfer and combustion in a nickel flash smelter have been investigated by numerical modelling and flow visualisation. The three-dimensional numerical model incorporates turbulent two-phase fluid dynamics, radiative heat transfer and combustion. The main features include the use of the k-E turbulence model, the Lagrangian tracking of particles, radiative heat transfer based on the spherical harmonics method, and chemical reactions. The predicted flow fields are in good agreement with data obtained from a series of flow visualisation experiments on a cold water model. The interaction mechanism between the fluid flow and the solid particles is examined for a range of particle sizes both with and without injected oil in a series of simulations. The heat transfer in the shaft is dominated by combustion and radiation, whereas the ignition of particles is influenced by the particle size and the added oil. Flow and temperature fields for both gas and solid particles are presented as well as the fraction of sulphur removed from the particles.

Jan 1, 1992

A nine-month investigation was conducted into the effect on coke quality and blast furnace operation of the addition of bentonite and southern coal to the northern coal fed to the coke ovens at the Newcastle steelworks.Additions of 0·3 per cent bentonite or 25 per cent southern coal to the northern coal increased the coke strength from 15-20 A.S.T.M. stability to 25-30 A.S.T.M. stability. It is likely that improved mixing and blending facilities would, in both cases, give a coke of over 30 A.S.T.M. stability.For the same coke strength, the use of 0 3 per cent imported Wyoming bentonite was considerably cheaper than the use of 25 per cent southern coal, but the use of Australian bentonite promises the same coke strength for still lower costs. Other additives such as coke breeze, charcoal, iron ore fines, and certain other finely divided materials, gave relatively minor improvements in coke quality.There appeared to be sufficient improvement in blast furnace operation and production to justify full scale addition of bentonite to improve coke quality, although other variables, particularly iron ore physical quality, overshadowed on many occasions the effect of coke quality. Further coke trials with southern or bentonite will be carried out when ore quality has been improved by the introduction of ore sintering at Newcastle.INTRODUCTIONDuring the period of operation of the Newcastle coke ovens and blast furnaces from April 1960 (when No. 3 blast furnace was blown in after rebuilding) to December 1960, a bentonite coke trial was carried out based on earlier research findings (Gregory, 1959a, 1959b; Felton and Gregory, 1960; Gregory, 1960) that as little as 0 3 per cent to 05 per cent bentonite clay added to northern N.S.W. high volatile coking coals gave a significant increase in coke strength. The bentonite coke trial was followed by trials...

Jan 1, 1962

Quite often the reserve assessor becomes enamored with the numbers gen- erated and forgets the basis for his assessment. The quality of the assess- ment can only be as good as the quality of the input data. The use of seismic data from the Gippsland Basin in assess- ing Esso/BHP's oil and gas reserves is an excellent example of this principle. By significantly improving the quality of seismic data, a much more reliable estimate of a field's reserve potential can be made. In addition, it provides the basis for further delineation drill- ing which, as recent experience in Gippsland has shown, often leads to increased reserves.

Jan 1, 1979

By Renwick MT

Two innovative ground reinforcement products have been developed for use in the mining industry. One of these products is a high strength polyethylene (HOPE) bar for use as a rib bolt in underground coal mining and as a corrosion proof tendon in open pit mines. The other product is a cable bolt (Ultrastrand) which demonstrates enhanced load transfer and is available in continuous lengths. Ultrastrand's exceptional in- situ performance and versatility makes it ideal for mechanised installation in both underground and surface mining operations. Details of these products are presented and results from labortaory and field trials are discussed.

Jan 1, 1992

The effect of accurate detonator delay timing on blast results can now be studied with the development of the ICI Electronic Detonator. This detonator has an accuracy and precision orders of magnitude greater than the current range of pyrotechnic delay detonators. A series of field trials have been conducted to quantify the effect of delay accuracy and timing on blast performance. These trials have demon- strated that delay timing can have a marked influence on blast fragmen- tation, muckpile displacement, blast vibration and airblast.

Jan 1, 1989

By Lyman GJ

Systems for the routine on-line determination of ash content of process streams in coal preparation plants and handling systems have been in use in Australia for over four years. More recently, monitors for on-line moisture measurement have been developed to complement the ash measurement function. The technology for these systems is reviewed briefly. The development of reliable ash and moisture monitors has made the implementation of automatic systems of coal quality control practical. The emerging philosophies of automatic control in Australian preparation plants are examined with particular emphasis on systems involving dense medium circuit regulation. Related developments in flotation control and coal sorting are noted to complete this overview.

Jan 1, 1987

By Takiuchi T, Kurita M, Owada S

This paper describes the possibility of the application of flotation to the separation of monazite from xenotime and of columbite from ferberite, which have been said to be difficult with generally used physical beneficiation methods. For Malaysian monazite and xenotime samples, a great difference is observed between the flotation recoveries at pH 7.5 using 1.0 x 10-4mol/1 dodecylammonium chloride (DAC). The grade and recovery of columbite in the binary flotation with both minerals result in 85 per cent and 67 per cent in the cleaning froth and 91 per cent and 51 per cent in the re-cleaning froth, without adding any scavenging stages. For monazite samples from various localities, the flotability is dominated by the electrostatic interaction between mineral surface and collector ion using DAC as collector, but the singular decrease of flotation is observed in the sample of which the crystallinity is low and the surface structure is rugged and complex. Otherwise, ferric ion in the flotation system probably dissolved from mineral is found to activate the flotation using sodium dodecylsulfate as collector. For columbite and ferberite, the separation is judged possible at pH 3.0 using 1.0 x 10'3mo1/l sodium oleate (NaOl) from the single flotation results of each mineral. In the binary flotation, however, columbite recovery in the froth is greatly diminished below that expected. This would be because NaOl is prevented from adsorbing on the columbite surface of which the charge is transformed more negative side by the specific adsorption of the tungstate ion dissolved from ferberite.

Jan 1, 1993

By Hocking G

For some underground structures, the use of the plane strain assumption in stress analyses may not be justified. The finite element method and photoelasticity have been used to obtain complete 3-D solutions, but, for various reasons, neither method has found universal use. The boundary integral equation method (B.I.E.M.) can be more efficient and economical than the finite element method for 3-D problems involving large volume to surface area ratios. A B.I.E.M. program developed for calculating stresses and deformations in infinite elastic media has been used to determine the 3-D distributions of stress around T- and Y- junctions of circular tunnels in stress fields in which the ratios of horizontal to vertical stress are 0, 0.33, 1.0 and 2.0. For the T- junction considered,stress concentrations at the intersection are approximately twice the plane strain values. Except where horizontal field stresses are high, the stresses in both tunnels approximate the plane strain values at about two tunnel diameters from the point of intersection of the tunnel centre lines. The stresses in the two branches reach those for the corresponding plane strain, two parallel tunnel case two diameters from the point of intersection of thq inner tunnel walls. Very high stress concentra- tions occur in the pillar of rock between the inner tunnel walls near the point of intersection.

Jan 1, 1976

By Jorgensen FRA, Moyle FJ, Turner TM

Laminar flow furnace techniques and thermal analysis were used to study the combustion of Kambalda nickel concentrate and Collie coal. The study was made to ascertain the suitability of the latter as a replacement for the fuel oil currently burnt in a flash furnace at the Kal- goorlie Nickel Smelter. The coal was found to ignite at temperatures between 500-600¦C which was the same as that required for the most reac- tive component of the concentrate, namely py- rite. The rates of reaction of both the coal and concentrate were dependent on oxygen con- centration. Sulfur dioxide hindered the combus- tion of concentrate and of coal, the effect on the concentrate being the more pronounced. The effects of moisture content and the tendency for spontaneous combustion of the coal were also noted.

Jan 1, 1982

By Sengstock G. W, Spathis A. T

Benchmarks of mine equipment involved in the excavation process of coal mines would suggest that such equipment is not always operating at an optimum level. Dragline operations and truck/shovel operations rely on efficient use of their plant in order to maintain high mine throughput. The first process which affects the material to be excavated is the drilling and blasting process. Drilling and blasting delivers a fragmented material with a given disposition ready for excavation by mine equipment. As mine operators demand more productivity from their major excavating equipment, many sites are considering the use of productivity monitors to measure their outputs. Some of these productivity improvements will be directly related to the drilling and blasting process, so that as the monitoring systems improve, the opportunities to evaluate all drilling and blasting variables will also improve. This paper reviews current and newer methods for monitoring equipment productivity in mines. These include simple time and motion studies obtained by either manual timing of processes or by automated data collection equipment being adopted by the industry. Case studies for truck/shovel operations are discussed and the productivity improvements are compared with typical industry standards. These improvements relate specifically to parts of the load, haul and dump cycle and the potential for significant improvements are identified. Particular opportunities for drilling and blasting improvements are also presented.

Jan 1, 1995

Oxygen is required for the leaching of gold ores in cyanide solutions. The source of this oxygen demand and the effect of dissolved oxygen concentration on the rate of the process are briefly reviewed.A method of measuring the oxygen consumption rate is described and some experimental results reported.Fundamental aeration theory and rating of aerators is summarised to show how this type of experimental work provides the basis for full-scale design of aeration equipment.

Jan 1, 1984

By Littlewood E

We offer these notes as a practical contribution. All the arguments we advance have been tested by practical experience.In its preparation we realised that our subject was one of such importance and covered so wide a field that, dealt with by one of us alone, it might easily have been too much for him, so we have endeavoured, by mutual criticism and advice and a pooling of ideas, to bring forward a few points that may be of advantage to members. If any of the paper is of benefit to mining on the "Golden Mile," or elsewhere, we shall feel amply repaid for our efforts.It is obvious to all that the longer the machine is working productively per shift the greater the return, to all concerned; the machine-man himself and the company. Furthermore, if a man commences a shift with a definite objective in view; for instance, to bore and fire a specific cut, which he recognizes will give him a good financial return, then that man will exercise all his capabilities to attain that objective.In this paper we hope to demonstrate the value to the machine-man of the knowledge of the capabilities of each hole he bores, so that he will be enabled to utilize his drilling time to the greatest advantage. Also, we hope to show that such drilling time can be advantageously extended.After the war, with the influx of new men to the industry, some education on the finer points of machine work may be desirable, and any instruction in this branch must stress the realization of the value of each hole.We realise that most of those present have a sound workable knowledge of machine-mining, and we are not trying to teach anyone the fundamentals of machine work, but we would like to bring to their attentIon some of the finer points which we believe are very important.The machine-man has control of gear of a capital value of over £150, and the use or misuse of that material has a direct bearing on working costs. Therefore it is imperative that the capital outlay is gainfully employed.A "bogger" in charge of a 5/- shovel engaged unproductively is bad enough. How much worse for £150 worth of gear to be not fully productive.Figs. 1 and 2 demonstrate angles of break, and the full realization of the importance of this angle is essential to our paper. Although these Sketches are two-dimensional, we hope they will be sufficient to demonstrate our meaning. We will pass over them as briefly as possible.Fig. 1 shows three holes asked to perform an identical task.(a) 7-ft. hole bored 2 ft. into solid ground-will not come out.(b) 4-ft. hole bored 1 ft. from solid ground-will come out easily.(c) 5-ft. hole bored to solid ground-the best that can be expected under general conditions encountered.The angle of break is a right-angle, normal to direction of hole.

Jan 1, 1944

Drag pick roadheaders and continuous miners have been applied in the coal mining industry for several decades, having replaced drill-blast methods as the primary means of excavating coal and coal-measures strata. The generally harder rock types associated with metalliferous mining have precluded the use of such machines in the past, however, developments in machine technology and increasing labour costs and environmental constraints suggest that there are now likely to be applications suited to the method. Metalliferous mining engineers are generally unfamiliar with the machines themselves and with the fundamental criteria controlling rock cuttability. This paper gives an introduction to the machines and the controlling factors.

Jan 1, 1987

A major tool in the search for petroleum is reflection seismic mapping. The period which has seen most of the exploration in Victoria is also one which has seen major advances in this technology, from 1963 try present day. Seismic mapping can be divided into three interlinked areas - acquisition, processing, and interpretation. In acquisition the major changes have been from an explosive energy source in 1963 to gas exploders in 1968 and airguns in 1970. The number of recording channels has increased from 24 to 192, with digital recording introduced in 1966, and floating point recording in 1976.

Jan 1, 1982

By Pradhan GK

Blasting is one of the most important operations involved in surface coal mining. The removal of over-burden waste in surface coal mines of India had experienced many improvements in terms of blasting, explosives selection, blast design, equipment selection, deployment. etc. Two case studies of very large surface coal mines have particular importance in their blasting operations. Both these units have been equipped with large capacity excavating machines, hauling units and also have some difficult mining situations. Blasting is done in benches in close proximity to human dwellings and over coal seams developed by underground methods with problems of high wall stability etc, as well. The various steps taken to improve the blasting operations ensure smooth operation of the equipment to meet the targetted coal production.

Jan 1, 1991

In an area north of Mowit Ica chip sampling of limonitic outcrops on a regional scale led to the investigation of a number of areas considered to be geochemically anomalous for copper and zinc. These areas were closely gridded,end where geochemical results were favourable, they were subsequently drilled or ro¦titeaned Che results indicated that for copper Lne anomalies were mainly associated wiL_ ironstone formed in areas of faulting. is suggested that copper is able to move considerable distances by ground water movement and is likely to be fixed under conditions of low pH. The movement of zinc is more difficult to explain but it appears to have an affinity for iron and is only deposited in areas having a high pH (i.e. doioiirific scdimet=Cs).

Jan 1, 1973

An ongoing research program into surface subsidence over Room and Pillar coal mining is described. A subsidence monitoring network has been established for one Room and Pillar mine in the West Moreton Coal Field of South East Queensland, at which pillar extraction is being conducted. The maximum measured subsidence to 28 January 1986 was 638 mm, with movement continuing. Analysis of the monitoring data with view to application of the subsidence pre- diction theory developed by Kowalczyk (1972) is discussed. The Kowalczyk theory provides predictions of subsidence depression, slope of surface, horizontal displacement, surface curvature and horizontal strain, for both the Partial and Total Settlement cases. The development of subsidence with time is also investigated and a preliminary analysis conducted.

Jan 1, 1986