Search Documents

By Moxon N. T, Berndt J. R

BHP-Utah Coal Limited's Peak Downs Mine is located in Cen- tral Queensland, approximately 200 km south west of Mackay. The annual raw coal production of the mine is over 8 million tpa, requiring the removal of about 40 million cubic metres of prime overburden. This is achieved through the use of five large draglines. The large depths of overburden (up to 55 metres) encountered over half the strike length of the mine enables cast blasting to be carried out in conjunction with draglines employ- ing the chopping method of digging. The objective of cast blast- ing is to use explosive energy to move as much material directly into spoil as possible. The additional costs of drilling and blast- ing are offset by reducing dragline rehandle. Two factors which are of primary importance to the design of cast blasts are initiation control and material velocity. High speed motion picture photography is a powerful diagnostic tool to quantify these aspects of blasting (Winzer, Montenyohl and Ritter, 1979; Chiappetta et al., 1983; Anon., 1983). The objec- tives of such analysis are to: 1. Determine the burden velocity, 2. Determine the time to initial movement (that is, the inter- val between a face hole firing and the initial movement of the burden), 3. Check the accuracy of the initiation sequence. BHP Central Research Laboratories (CRL) and Peak Downs Mine monitored a cast blast in the mine's Winchester Pit on 18 August, 1988. The objectives of this exercise were to: 1. Quantify current cast blast performance, providing a base case for comparison with modified blast design. 2. Compare two orientations of angled holes within the blast. 3. Assess the effectiveness of cast blasting utilising an air-deck. 4. Check blast timing with respect to burden movement times.

Jan 1, 1989

Underground mining in the West Moreton coal field started in the 1870's. Subsidence related to coal mining activities is an ongoing problem facing planners and developers in the Ipswich area in South Eastern Queensland. The history of coal mining in the area over the last 110 years has left the legacy of periodic surface instability in several areas. In general, modern engineering analysis with current mining methods combine to create predicatable analysis of surface stability and movement. Where old workings using several variations of the bord and pillar system are affected by current activity, the predictibility of the surface movement is greatly reduced. Geological complexities further complicate the analysis. Mining and the related dewatering affects the stresses on pillars in old workings. This is caused by reducing buoyancy effects caused by changes in the water levels in old workings. Of particular relevance is the depth of workings and strength of the coal and overburden. The type of subsidence affecting the surface can range from localised pillar failure, to roof failure and potholing and the likelihood of the particular form of subsidence can be assessed from studying the workings in relation to the stratigraphy and structure of the coal measure Formations.

Jan 1, 1988

By Sandvik

Fine grinding in an air-swept ball mill working in closed circuit with a forced vortex air classifier has been investigated first in continuous laboratory and then in industrial scale. Results from the laboratory circuit have shown significant influence of mill load (powder filling) on the capacity of the circuit. In laboratory scale the mill load was measured and controlled by a weighing platform placed under the complete mill set-up. The mill load of the industrial air-swept ball mill has till now been controlled by measuring the power consumption of the mill motor. Thus, it was necessary to operate far from the range of optimal mill filling. To improve the circuit performance, alternative ways of mill load measurement were investigated. An important factor was investment cost, as many fine grinding mills operate in relatively small circuits that do not wan-ant large investment. In this case the task was accomplished by using a piezoelectric strain transducer, which detected strain changes in the mill shell. It was installed in the midpoint of the shell, where the highest deformation was obtained. As the transducer was on the top position, it indicated compression, and on the bottom position it measured tension. By taking the difference between the readings, it was possible to calculate total strain variations, directly proportional to the mill load. The signal from the transducer was sent to a control room via a cordless infrared communication system, employing a microprocessor control card, which could further regulate other operating parameters of the circuit according to the software model. The installation required very low investment cost and provided simplicity of application as well as stability and reliability of characteristics under severe industrial condition. The measurement system made it possible to optimise the mill load and thus increase the production from 3.2 to 3.7 dh (15 per cent), and stabilise the circuit operation.

Jan 1, 1995

By Wood CJ, Davis JJ, Askew H

A dynamic model of a dense medium circuit has been developed and tested against plant data. The model shows the response of the circuit to both controlled (changes in specific gravity set point or changes in circuit coal feed rate) and uncontrolled changes (changes in raw coal moisture, loss of raw coal feed) in operating conditions. The model is built up from dynamic models of the individual sumps, pumps, pipes, splitters, magnetic separators and automatic controllers in the circuit. The model can be used for design of automatic control loops and for investigation of possible process modifications such as changes in water addition points. This paper describes the model construction, the testing of the model against actual plant data and gives some examples of its use in investigating plant response to changes in operating conditions.

Jan 1, 1978

By Nott M. C

The oxidation of xanthate collectors to xanthate/dixanthogen results in a higher hydrophobicity of sulphide minerals surfaces due to the action of dixanthogen. This higher hydrophobicity can be proved on a fundamental level by examining the st

Jan 1, 1994

By Thomas CG, Armstrong GJ, Lynch KS

A small glass walled pot grate has been used to simulate drying of iron ore pellets in a travelling grate plant. This equipment has enabled the effect of decreasing grind and de- creasing pellet bulk density on plant production to be quantitatively predicted. These predic- tions are compared with plant experience. The use of the laboratory simulator in comparing the effect of various additives on plant production is also described and substantial improvements in both the goethite and free-water drying periods are predicted.

Jan 1, 1972

The phosphatic overburden of Christmas Island is a lateritic soil and consists dominantly of crandallite and millisite. These minerals are polymorphs of general formula, (Na,K)x Ca2-x (Al, Fe)6 (PO4)4 (OH)10-x (2+x) H2O. Iron occurs only in millisite. Both minerals exhibit similar thermal transformations, dehydroxylating near 600¦C and recrystallizing above 800¦C. Dehydroxylation results in crystal structure collapse but retention of crystal morphology. Ggethite, boehmite and apatite are minor constituents of some-of the phosphatic Soils.

Jan 1, 1971

The theory of declining optimimum cut-off grades is more than 25 years old, but for a number of reasons it is still not widely used in industry. A lack of faith in the veracity of estimated grades is not in itself a reason to abandon any attempt to optimise cut-off grades. The use of declining cut-off grades has been thought to cause high-grading, but in fact this is only true if an artificially high discount rate is used in the calculations. Perfect application of an optimum cut-off grade should ensure that only ore generating more than a minimum net return is mined, and that as much as possible of the ore capable of generating that return is mined. Therefore differing mining costs in different parts of some underground mines necessitate local modifications to cut-off grade. Optimisation of cut-off grade is of necessity an iterative process. Integration of that process into a feasibility study need not be excessively time-consuming. A number of approximations can be made to speed the optimisation (any attempt to achieve a high level of accuracy is probably doomed to failure by a lack of precise cost and price projections). A procedure is outlined for optimising cut-off grade during planning of a typical underground mine.

Jan 1, 1991

By Hoskings R

Conceptual studies of the run of mine stockpiling and reclaiming requirements com- menced in 1975. Final selection of equipment was made in 1978 and the equipment was commissioned in June, 1979. Equipment selection was made after extensive investigation and visits to existing facilities throughout the world. The equipment selected is described and com- pared with the alternatives. Foundations were designed to minimise clean up effort and to ensure stability of equipment under design wind loading without storm bays. Program- mable logic control enables the stacking and reclaiming facility to provide a blended feed to the coal preparation plant.

Jan 1, 1980

Simple parameters, capable of easy observation on-site under operating conditions without interruption to production, are outlined for the operational assessment of underground conveyor systems. Recording techniques, methods of analysis and deduction of operational characteristics are discussed for batch inputs to several points of a multiple belt conveyor system with limited inter-belt storage capacity. Particular attention is given to input and output load- time distributions, utilisation of inter-belt storage capability and system shutdown behaviour. Actual data, observed for a transfer feeder located between two trunk conveyor belts in an underground coal mine, is used to illustrate the operational assessment of an underground system. Load sensitive feedback systems-are briefly considered.

Jan 1, 1982

The paper considers the nature of outbursts of coal and firedamp as they occur. t follows the development of methods of working used to try and induce outbursts safely under controlled conditions and details the life support systems used to provide maximum rotection to persons who may be affected by s_lontaneous outbursts. Tilt: NATURE OF OUTBURSTS IN THE UNITED KINGDOM .1y some areas in the coalfields of the ingdom are affected by outbursts of :hal and firedamp. The main area affected is he western end of the Anthracite coalfield r: West Wales. In this area 206 outbursts .eve been recorded resulting in the loss of 8 lives. Anthracite is a high rank coal produced v the geological effects of age, depth and ynamic metamorphism. Outbursts have been xperienced over a wide area of the anthracite field but have been most frequent, and most evere, in the areas where carbon content is its highest and where the coal measures cave been subjected to the highest degree of eulting and overthrusting. Most outbursts ire associated with geological abnormalities ,:id the coal ejected during outbursts is sually of a soft and powdery nature.

Jan 1, 1980

By Lowell J. D

This paper is an outgrowth of a continuing compilation of the geology of Chilean ore deposits by Carlos Ruiz who was the author in 1965 of Geologia y Yacimientos Metaliferos de Chile which was the definitive compilation of the ore deposits of Chile. A new version was written by him in 1988, with the co-operation of Federico Peebles L, published in Geologia, Distribucion y Genesis de los Yacimientos Metaliferos Chilenos. Over the past eight years J David Lowell studied the geology of the Chilean mineral belts in connection with planning mineral exploration for copper and gold.

Jan 1, 1990

This paper covers the key issues such as orebody geometry and grade, geotechnical data and metallurgical response. These must be considered in selecting a mining system for a new orebody. It then focusses on the advantages of open pit mining over underground mining particularly in the areas of costs, speed of development and safety. Environmental issues with waste storage is the only negative which emerges. Consequently, the majority of new large mine developments continue to be open pits. It is also demonstrated that underground mining continues to play an important role, particulary for high-grade deposits at depth. The impact on ore recoveries of recent developments in stabilised fill technology in underground mining is also highlighted. The importance of economics to the decision on mining method is continually emphasised as maximising orebody value should be the prime objective of this Work.

Jan 1, 1997

By Kavetsky A, Scott A

As well as breaking and moving rock, blast energy sets up a seismic wave in the ground which can cause significant damage to rock structures and buildings and disturbance to human occupants. This seismic ground vibration is potentially most damaging when its dominant frequency coincides with the resonant frequency of a structure, leading to high amplification factors between the input ground vibration and the resulting structural response. This paper outlines methods of identifying the resonant frequency of structures. It also describes a practical numerical method for the modification of blast designs to reduce the ground vibration energy in critical frequency ranges. The method is illustrated with two recent case studies.

Jan 1, 1990

By Hale C. T, Carnie W. A

Rosebery mine has had over 100 years of mining activity. The reserve has remained static for the last eight years with an expected mine life of six years. A move to rectify this was made in 1994 with the birth of the Deep Exploration Project (DEP). $45 M was committed to drill 100 km of underground exploration diamond drilling and develop 5.5 kin of decline aiming to add 9.5 Mt to the reserves and minimise lead time for development of P and K lenses discovered in the early-1990s. In 1996 this aim was expanded with the objective to build the resource base to 20 Mt by June 2000 allowing the mill to operate at 1.0 Mtpa (0.9 Mt from underground). Preliminary results of the project to-date are outlined and exploration diamond drilling techniques and strategies are described.

Jan 1, 1997

Production from a major, deep orebody requires the construction of two 6 m diameter, 1000 m deep ventilation shafts over the next three years. Further ventilation upgrades have foreshadowed an additional 1500 m of 6 m diameter shafts beyond that. After reviewing the construction alternatives it was decided to raisebore the first shaft in one pass using Western Mining Corporation's 121R raiseborer and the Wirth sequential head. The significant cost and speed of construction potential of 6 m raiseboring justified the risks associated with this new technology. Large diameter sequential head raiseboring has only been carried out in South Africa. Over the last three years many lessons have been learnt and the technology has progressed to being considered feasible. Operating practice and the optimisation of raiseboring performance for specific ground conditions are the areas requiring further work. The development of large diameter raiseboring in South Africa and the site preparation and initial operation at Z.C. Mines are described. Comment on actual operating experience includes the geotechnical investigations, the raiseborer foundations, cuttings disposal and the drilling of the pilot hole which has progressed to beyond 450 m. Unforeseen difficulties with the verticality of the pilot hole and with mud losses illustrate the types of problems that can be expected.

Jan 1, 1988

By Murray C. G

A database of over 1300 earthquakes has been used to investigate the relationship between seismicity and tectonics in two areas of eastern Queensland and NE New South Wales. These areas have been monitored by several networks that were installed primarily to monitor seismicity associated with the impounding of large reservoirs. Events that occurred prior to the installation of these networks have been excluded from the analysis because they have large uncertainties in location.Seismicity in SE Queensland and NE New South Wales is concentrated in the coastal regions. Activity also extends off the coast of Queensland and beyond the continental shelf. The coastal activity is mainly within the New England Fold Belt. An area of the fold belt overlain by the Clarence-Moreton Basin is also active. There is an area of activity near St. George that correlates to the Wunger Ridge. Fraser Island and the adjacent onshore area, near Maryborough, are notably aseismic.Within the New England Fold Belt there is a NNW trending zone of concentrated activity that includes the South D'Aguilar Block and the Esk Trough as far as Gayndah. The Nambour Basin, the Gympie Province, and the southern portion of the Yarrol Block are significantly less active.Composite focal mechanisms of several groups of accurately located earthquakes in SE Queensland indicate predominantly reverse faulting. This faulting is the result of the crust being compressed horizontally in a NE-SW direction.Activity in the Burdekin Falls Dam area of central eastern Queensland is confined to the Drummond and Bowen Basins. There is also significant activity offshore from Townsville and Bowen.

Jan 1, 1990

Designing for early access to deep orebodies is an essential driver for improved project payback. Vertical shaft sinking techniques have been developed to allow concurrent mine level excavation while continuing to sink. Project cash flows can also be improved when simultaneously deepening existing shafts beneath operating hoisting systems. Further economic advantage has been realised through creative sinking sequencing in twin ventilation/service shaft projects. A fourth technique to reduce project schedules involves partial shaft barrel equipping allowing unrestricted access to construct stations and continue with level installations. This approach reduces interference with barrel sinking activities to insignificant proportions. This paper reviews how these approaches have added significant value to actual shaft sinking projects, as assessed from a contractorÆs perspective, and discusses some of the practical issues to be addressed when planning future projects. Designers need to take cognisance throughout all project engineering phases of the adage that you are only sinking when cleaning the face. Cleaning can only be sustained when there is sufficient hoisting capacity.

Jan 1, 2005

The results of about 30 years of exploration and mining activities and research studies in the Kambalda mining district, Western Australia, have led to general agreement that the komatiite-associated Ni sulphide ores formed as a result of igneous processes (Ross, 1974; Ross and Hopkins, 1975; Gresham and Loftus-Hills, 1981; Cowden, 1988; Lesher, 1989 and many others). Despite this agreement, the controls on sulphide supersaturation and concentration of the resulting sulphide in a limited zone, remain uncertain and controversial. A major uncertainty is the source of sulphur in the ore deposits. Two principal sulphur sources have been proposed: 1. komatiite lava/magma (Hudson, 1972; Naldrett, 1973; Lesher et al, 1981; Cowden, 1988; Foster et at, 1995), and 2. sedimentary material (Groves, Barrett and McQueen, 1979; Lesher, Arndt and Groves, 1984; Lesher, 1989; Lesher and Campbell, 1993). Resolution of the uncertainty regarding the sulphur source is required for a complete understanding of the controls on ore formation, which in turn would significantly impact exploration strategies in the Kambalda mining district and elsewhere. This paper reviews the constraints on sulphur sources for the komatiite-associated Ni sulphide ores in the Kambalda mining district. The focus is on the general characteristics of the ores and surrounding rocks: individual ore deposits are not described, though specific examples are noted where appropriate. The stratigraphic and volcanic settings and geochemical (major and trace element and isotopic compositions) characteristics of the ore deposits and surrounding rocks are considered within the context of the competing sulphur source models, and future directions of research in the district are noted.

Jan 1, 1996

By Daniels E. J, Morgan W. A

In response to the increase in consumption of galvanised steel for automobiles in the last decade and the problems associated with remelting larger quantities of galvanised steel scrap, a process is being developed to separate and recover the steel and zinc from galvanised ferrous scrap. The zinc is dissolved from the scrap in hot caustic using anodic assistance and is recovered electrolytically as dendritic powder. The dezinced ferrous scrap is rinsed and used directly. The process is effective for zinc, lead, and aluminum removal on loose and baled scrap and on all types of galvanised steel. The process has been pilot tested for batch treatment of 900 tonnes of mostly baled scrap. A pilot plant to treat continuously loose scrap, with a design capacity of 48 000 tonnes annually, has been in operation in East Chicago, Indiana since early in 1993. The first 450 t of scrap degalvanised in the pilot plant have residual zinc below 0.01 per cent and sodium dragout below 0.01 per cent. Use of degalvanised steel scrap decreases raw materials, environmental compliance costs, and opportunity costs to steel- and iron-makers. Availability of clean degalvanised scrap may enable integrated steel producers to recycle furnace dusts to the sinter plant and EAF shops to produce flat products without the use of high quality scrap alternatives such as DRI, pig iron, or iron carbide. Recycling the components of galvanised steel scrap saves primary energy, decreases zinc imports, and adds value to the scrap. The quantities of zinc available by the year 2000 from prompt and obsolete automotive scrap will approach 25 per cent of zinc consumed in the major automotive production centres of the world. Zinc recycling from galvanised steel scrap, either before or after scrap melting, will have to be Implemented.

Jan 1, 1993