Search Documents

The last one decade in India had witnessed phenomenal growth in the coal, lignite, iron ore, limestone and many other minerals. To meet the production of minerals, the energy requirement is also very high both in terms of petroleum products and electrical energy. Because of spiralling prices of crude oil and also of the electrical energy, attempts have been made by various mining companies to select energy efficient mining machineries (in underground and surface) mines, together with energy efficient mining and mineral processing operations. Mineral sector of India is working seriously in tune with the Planning Commission stipulations to conserve energy.Apart from energy use (both electrical and fossil fuels) in mining, it is also significantly contributing to the cost of mineral processing depending on the quality of ore/rock being processed. Over the years a number of studies have been initiated and implemented to reduce cost of energy bill. An attempt has been made to present the various aspects of energy conservation, Impact of Energy Conservation Act 2001, Relevance of energy audit, areas of energy consumption and conservation efforts, etc in this paper. The paper also deals with some of the case studies to show how energy conservation programs has been implemented in the Indian mineral sector.

Dec 6, 2010

Up to 19 chemical parameters were studied in flotation pulps in six Australian lead-zinc concentrators with the aim of obtaining a better understanding of the nature of, and changes in, the chemical environment. This paperdiscusses pH, redox potential, and oxygen concentrations, which were all measured continuously.Two plants operated at natural pH in slightly acid circuit and one at natural pH in alkaline circuit, and pH was stable at all these plants. In two plants varying amounts of cement fill were present in mill feed and pHwas variable. At the other plant pH was controlled with soda ash and lime.Redox potentials became more positive as the pulp passed through the plant. The minimum change was 20 mV and the maximum about 250 mV. Potentials tended to be variable at any point early in the circuit, but were more stable later on. In some plants reagent additions had no noticeable effect on redox potentials. However in the two plants operating in acid circuit the redox potential of .zinc rougher feed was markedly affected by changes in copper sulphate addition rate. Sodium sulphite additions had an effect at other plants.Oxygen concentrations in grinding circuits tended to be low (30 per cent of saturation) and very variable. Flotation was usually conducted in pulps at least 90 per cent saturated with oxygen. Addition of sodium sulphite had a marked effect on oxygen content in one plant, but less effect in two others.Statistically significant relationships were found in some plants between pH and redox potential, redox potential and oxygen saturation, and oxygen saturation and pH.Improved control of copper sulphate and sodium sulphite additions could result from applications of this work.

Jan 1, 1970

By F Farías, D Villa

Codelco’s Salvador Project has been operating a block/panel caving mine for more than 50 years. This underground mining method dynamically mixes the ore and dilution. As a result, forecasting grades is difficult and achieving 100 per cent extraction of the reserves is practically impossible. A substantial volume of the ore mixed with dilution becomes remnant ore and remains to be subsequently extracted.A potential open pit mine is under evaluation at Codelco’s Salvador Project, which includes the extraction of remnant ore post-block caving extraction. An effective methodology has been implemented to estimate what is left behind once the underground mine has closed. A new mixing method using the Cellular Automata (Alfaro and Saavedra, 2004) approach has been used to allow estimation of the remnant ore with a sufficient level of confidence to be included as part of the open pit reserve.A remnant block model is created using elements such as in situ block model, drawpoint layouts, historical production records and the drawpoint extraction. Using this information, simulations of the extraction of the mine by month from 1959 to 2019 were completed, using different mixing scenarios and trying to replicate the tonnage and grade extracted.Finally, the remnant block model is categorised using a score card with four inputs to assess the risk of the estimation of this material into a category class (measured, indicated and inferred).CITATION:Villa, D and Farías, F, 2016. Remnant ore model generation and categorisation post-block caving extraction at Salvador Mine, in Proceedings Seventh International Conference and Exhibition on Mass Mining (MassMin 2016), pp 461–470 (The Australasian Institute of Mining and Metallurgy: Melbourne).

May 9, 2016

By Y Yang

This paper discusses various issues surrounding the metallurgical control for furnaces, especially focusing on processes with long time-constants and æmetallurgical memoriesÆ. Examples will focus on furnaces accepting particulate and sometimes ill-defined feeds, eg submerged-arc furnaces, blast furnaces, secondary scrap smelting operations, recycling operations, waste incinerators, etc. Generally, because of the usually higher metallurgical time constant of these furnaces, these reactors have to be controlled in a feed-forward manner by the use of a hybrid of æblack boxÆ or empirical and ægrey boxÆ semi-empirical first principles metallurgical modelling and simulation techniques in a supervisory metallurgical control capacity.

Jan 1, 2000

In preparing this paper, the writer hopes to achieve two main objects. Firstly, an indication of the desirable features of coke from the viewpoint of a blast furnace operator should be of assistance and value to those connected with coal and coke research, coal mining, the manufacture of coke and the production of iron. Secondly, it is hoped that the conclusions and opinions expressed herein, which are known to be of a controversial nature, will promote some discussion and thought. In this way, other workers may see fit to contribute and enlarge our general knowledge of Australian coke and its behaviour in blast furnaces.Those properties of coke that are considered to be of importance to blast furnace operation will be examined. Although broadly speaking, the composition and characteristics of coke are inherent in the coals used, any special features of coal preparation and carbonization that affect the resultant coke will be discussed. An attempt will also be made to indicate the effect on blast furnace operation of significant irregularities in these properties.THE FUNCTION OF COKE IN A BLAST FURNACECoke has four important functions in a blast furnace:1. To reduce the oxides of iron and other elements to metal and to provide the carbon absorbed by the iron.2. To supply the necessary heat for the process.3. To provide an open supporting structure in which the descending ore and limestone lie exposed to the action of the ascending gas.4. To provide voidage in the bottom of the furnace, so that iron and slag can accumulate in the hearth.

Jan 1, 1957

The Tasman Orogenic Zone is regarded as a single metallogenic province (the Tasman Province) with four SUb-provinces corresponding with its major tectonic components: the Lachlan, New England, Hodgkinson.and North Queensland orogenic provinces. Within the Tasman Province there are four main ore-rock associations.These are1. manganese and iron with sedimentary and basic volcanic rocks,2. zinc-lead-copper and copper with intermediate-acid volcanic sequences,3. minor chromium, platinum, and osmiridium with ultramafic complexes, and4. tin, wolfram, gold, and copper with syn- and posttectonic granitic intrusions.Whereas the ores of ultramafic and volcanic associations form geographically-restricted metallogenic districts, the ubiquitous granitic ores may be subdivided into twenty-one districts that cover almost the entireOrogenic Zone. The Tasman Province is notably lacking in uranium ores and Mississippi Valley-type deposits.There is a distinct tendency for ores of each association to be progressively younger to the east and north, thus paralleling the progressive growth and stabilization of the Zone. Similar ore-rock associations are present in repeated phases of mineralization from the Cambrian to the Permian-Triassic, reflecting the essential homogeneity of the Tasman Province, and the similarity of the successive tectonic cycles.

Jan 1, 1972

To date Iron Monarch is the most important Australian source of iron ore and since HH5 has produced about 84 million tons of direct shipping ore containing 62 per cent iron and 3 per cent manganese.Previous geological work, mainly by Rudd, Edwards and Miles is reviewed and the results of later exploration by quarrying and drilling are discussed and modified interpretations of both stratigraphy and structure are advanced. Renewed study of the mineralogy of the iron ores is advocated.The Iron Monarch orebody lies on the up-thrown side of a major transcurrent fault that truncates it on its northern boundary. The nearby Iron Knob orebody is believed to occupy a horizon that is some thousand feet stratigraphically above Iron Monarch.The origin of the ore cannot be explained by any simple theory; development probably took place over a long period of time from Lower Palaeozoic to Tertiary.INTRODUCTIONIron Monarch orebody has supplied the Australian iron and steel industry with the greater part of its ironstone requirements since the establishment of the Newcastle steelworks in 1915. Annual production of direct-shipping ore has exceeded three million tons but declined slightly after 1956 when Iron Prince was brought into production. Total production of ore from Iron Monarch to the end of 1962 is about 84,000,000 long tons containing some 55,000,000 tons of metal.The deposit (Lat. 32°44'30"S : Long. 137°08'30"E) is 34 miles north-west of Whyalla, on the western shore of Spencer Gulf. A 42 in. gauge railway connects Iron Monarch and its associated small town of Iron Knob with Whyalla (Fig. 1).For the purpose of this paper Iron Monarch includes Iron Knob and the intervening jaspilite hill known as Substation Ridge, and the description of the general geology necessarily 'Assistant Chief Geologist, The Broken Hill Proprietary Co. Ltd.This paper was presented at the Annual Conference of The Institute, 14-24th August 1968.

Jan 1, 1964

CrusherMapperTM - A New Tool for Crusher Condition Monitoring The efficiency of mineral processing plants is entirely dependent on the availability of the plant equipment critical path. This typically concerns comminution circuits consisting of primary crushers and primary grinding mills. Crusher and mill availability are determined by the frequency and duration of maintenance shutdowns, which are primarily driven by the need for replacement of sacrificial liners. The change of crusher and mill liner shape over respective life cycles also strongly affects plant efficiency. It is therefore highly desirable to accurately monitor the condition of mills and crushers in order to optimise plant efficiency through maximised availability and targeted liner shape. Traditional comminution liner and other production parameter condition monitoring has been attempted through ineffective methods which prevent satisfactory management of crusher and mill maintenance and reduce operational control. This situation has recently dramatically improved for grinding mills through the development and commercial deployment of MillMapperÖ, a technology based on three-dimensional laser scanning data and dedicated software (Franke, Lichti and Stewart, 2006; Franke and Lichti, 2007; 2008; Franke, 2008; Franke, Redman, Johnson and Michalek, 2009). At the time of writing in late 2009, MillMapperÖ is in successful use at a rate of approximately 170 surveys and associated reports per annum at processing plants in Australasia, South America, North America and Africa. This paper presents the introduction of CrusherMapperÖ, the MillMapperÖ equivalent for crushers. CrusherMapperÖ also utilises high density, high accuracy laser scanning data, and features dedicated algorithms for three-dimensional monitoring of wear on crusher concaves and mantles. This facilitates the detection of wear hot spots or zones or localised liner failures, and accurate forecasting of reline tonnages and dates. It also for the first time provides the means to establish optimised concave and mantle shapes in order to achieve production targets. In contrast to any other currently utilised condition monitoring method, CrusherMapperÖ data collection can occur remotely and does not require any shutdown or crusher isolation. This method therefore does not interrupt crusher production while at the same time eliminating any confined space risk normally associated with taking measurements inside the crusher cavity.

Sep 13, 2010

By S Smit, P J. J Strobo

ZINIFEX Century Mine is a zinc, lead and silver concentrate producer. Flotation is the primary method of minerals separation in this circuit. The flotation circuit is quite large with 79 flotation cells. The levels in each of these interconnected cells are controlled at more than 45 level control stations. Due to the multivariable interaction throughout the circuit, good level control was found to be difficult to achieve by just using normal Proportional-Integral-Derivative (PID) control. As a first step in advanced process control, the FloatStar Level Stabiliser, a multivariable controller developed specifically for flotation circuits, has been commissioned at Century mine to solve the level control problems. The first section of this paper therefore discusses and shows the results and improvements obtained by using the FloatStar level stabiliser. The results and benefits of the FloatStar Flow Optimiser are discussed in the second section of this paper.

Jan 1, 2004

By Cooper R. J

The essential features of the zinc concentrate roasting installation at the Risdon Works by the Electrolytic Zinc Company of Australasia Ltd. are given.The problem of maintenance of ignition in down-draught zinc concentrate flash roasters is discussed, and a solution offered.A successful and economical method of using by-product oxygen for raising the roasting efficiency of hearth roasters is described. Three methods of utilizing oxygen for the same purpose in flash roasting are detailed, and their relative merit, considered.INTRODUCTIONThe zinc sulphide concentrate used at the Risdon Works is roasted autogenously for removal of sulphur in two hearth roasters, and four flash roasters. The hearth roasters are of modified Skinner type with eleven hearths. They were designed, and are used, for roasting mixtures of relatively low sulphide content. Their design and operation have been described elsewhere (Forster, 1949).The flash roasters are down-draughted furnaces with cross-section and rabbling equipment based on the hearth roaster design, and the process is similar to that developed by the Consolidated Mining and Smelting Company of Canada Ltd. (Cominco) at Trail, B.C. (Stimmel, Hannay, and McBean, 1936).These furnaces are 20 ft. in diameter. They have three drying hearths through which hot gas is drawn from the combustion chamber by the burner fan. The combustion chamber is 2'1 ft. high above the collecting hearth (27 ft. in No. 4 unit), and the discharge hearth below it is 6 ft. high, so that a large gas offtake is possible. Four rabble arms for each hearth are carried on a central column. Dried, ground concentrate, and the air for roasting it, are fed to a burner...

Jan 1, 1958

By J Temos

This paper outlines a number of immediate practical approaches to continuous improvement in environmental management in the minerals industry. It puts these into context with longer time-frame step-change approaches whose gestation may take a decade. Examples of improvements and approaches are drawn from WMC operations.

Jan 1, 2002

A Study of Extracting Vanadium from Stone Coal Using Cyclic Oxidation

Sep 13, 2010

By D FitzGerald, S Jakica, R Paterson, J Silic

A new 2.5D airborne electromagnetic (AEM) algorithm has been developed by Intrepid Geophysics and Jovan Silic & Associates. The advantage of 2.5D (2D geology, 3D source) AEM inversion in 3D geological mapping applications and identification of conductive drilling targets, compared to the more commonly used conductivity-depth imaging (CDI) transforms or 1D inversions, are demonstrated using examples from banded iron formations (BIFs) and other geological settings. We show emerging AEM systems are capable of providing estimates of economic rock unit thicknesses, dips and fault definition at an accuracy that mitigates the need for pattern drilling.The 2.5D inversion application used in this work and described in Silic et al (2015) is a substantially changed version of ArjunAir (Wilson, Raiche and Sugeng, 2006), a product of CSIRO/AMIRA project P223F. The changes include a new forward model algorithm and a new inversion solver. The application enables the accurate simulation of 3D source excitation for full domain models inclusive of topography, non-conforming boundaries and very high resistivity contrasts. Solution is accurate for a geoelectrical cross-section, which is relatively constant along a strike length that exceeds the AEM system footprint.The major innovation includes a new inversion solver with adaptive regularisation, which allows the incorporation of a misfit to the reference model and the model smoothness function.Memory usage has been dramatically reduced and is estimated prior to execution. For speed the software has been parallelised using Intel message passing interface (MPI) and can be used on standard computing hardware or computing clusters. Data from survey lines with lengths exceeding 100 km can be inverted on high end laptop computers.We allow flexibility in the selection of components and in the estimation of noise.AEM inversion examples are shown for surveys from BIFs, base metals (volcanogenic massive sulfides) and geological mapping projects and the results are compared with known geology and drilling. We demonstrate the much improved mapping and target definition delivered by this inversion method when compared with the other more common transforms or inversion methods used on these projects.CITATION:Paterson, R, Silic, J, FitzGerald, D and Jakica, S, 2017. High accuracy .D airborne electromagnetic inversion method for banded iron formation and other geological settings, in Proceedings Iron Ore 2017, pp 319–330 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 24, 2017

The fundamental features of the Cable Belt Conveyor are described. It consists of independent wire ropes which take the transmission load, and a special reinforced rubber belt which acts 'only as carrier of material. The first cable belt installation in Scotland is described briefly.A general description of this type of conveyor is followed by details of the rubber belt construction and the method of joining sections of belt. The drive unit, the tensioning arrangements and the power requirements are outlined.Applications of the cable belt conveyor are 'dealt with and its advantages summarized.INTRODUCTIONThe cable belt conveyor, as its name implies is a conveyor composed of steel wire ropes and a rubber belt, in which the ropes serve as transmission members, and the belt merely as a carrier of materials.Over the years it has been the ambition of engineers connected with the belt conveyor industry to develop a conveyor that would use the high tensile strength of wire ropes to transmit the stresses involved in the driving of large capacity belt conveyors. Different lines of approach have been adopted in the United States of America and in Britain. In the United States the method adopted was to introduce a large number of flexible steel cables into the rubber belt itself, in the form of a closely packed layer arranged across the full width of the belt. These small cables are packed in a nylon filled duck envelope which is incorporated in the rubber belt. This is commonly known as the steel corded conveyor belt. In Britain, a Scottish firm developed a rubber belt conveyor in which full advantage was taken of the high tensile features of wire rope, without embodying or moulding the wire rope into the rubber belt, so that the two wire ropes and the rubber...

Jan 1, 1957

The mineralogy and microstructure of mattes from the nickel flash smelter at Kalgoorlie, Western Australia, have been studied. The flash furnace matte consisted mainly of an intimate mixture of pentlandite and heazlewoodite with some nickel metal. The electric furnace matte was mainly an iron-nickel alloy with subsidiary pentlandite while the converter matte consisted mainly of heazlewoodite with crystals of nickel metal.

Jan 1, 1977

THE ore treated is almost pure copper pyrites (chalcopyrite) in a gangue of quartz and quartz-felsite. Very little free iron sulphide (pyrite) occurs, and at the time of the erection of the flotation plant the stopes in the oxidized zone had been almostentirely depleted. This zone only extends to a shallow depth, and, below the l00-ft. level, the sulphide for the most part is clean and bright but in the crushed and brecciated parts of the ore channel, where surface water has circulated freely, the gangue is decomposed and kaolinized, and the copper sulphide badly tarnished. This class of ore gave considerable trouble at the mill, but unfortunately, was very limited in quantity. A sample of rich ore assayed-Copper, 21.2 %; iron, 24:.3 %; silica, 28.9 %; sulphur, 25.1%.The concentration in the original mill was effected by handpicking, jigging, and tabling. A considerable portion of the copper mineral arrives at the surface in the form of large lumps of very pure quality, eminently suitable for sorting out by hand.The rich ore is tipped over a grizzly at the shaft bins; the oversize hand-picked, and the undersize bagged direct.

Jan 1, 1912

By K Gordon, A Black

Two remediation strategies have been considered to reduce the levels of acidity and dissolved metals in acid mine drainage discharging from Sullivan Mine, West Coast, New Zealand. The oxidising strategy involves adding alkalinity and dissolved oxygen (DO) resulting in the precipitation of metallic oxides and decreased acidity. The reducing strategy involves removing DO, resulting in the precipitation of metallic sulfides, followed by addition of alkalinity to decrease acidity. Field remediation trials indicate a reducing system may be more effective for this site than an oxidising system. A residence time of only two hours in the limestone layer of a successive alkalinity producing system (SAPS) is sufficient to reduce acidity by 100 per cent, iron by 71 per cent, aluminium by 59 per cent, nickel by 38 per cent and manganese by 26 per cent. The proposed remediation plan will likely include a series of SAPS, followed by an anoxic limestone drain, and settling ponds to capture any remaining precipitates.

Jan 1, 2003

By R J. Mills, B S. Sinclair, D A. Fergusson, A G. Goldstone

In 2005, Solid Energy New Zealand Limited obtained non-notified consent for the disposal of 1Mt of coal ash at the Rotowaro minesite, forming part of a coal supply agreement with the Huntly Power Station. The consenting of major mine site activities has historically required wide consultation and involves notification of the application.   The risk and cost associated with consultation can be significantly reduced via a non-notified process. A non-notified consenting process necessitates environmental effects to be shown to be æless than minorÆ, which requires the combination of robust science and a pragmatic approach to design, assessment of environmental effects, and consenting issues.   Key issues examined included consideration of how to practically operate a significant disposal project within the confines of an operating mine, minimising the costs, civil and geotechnical design and practical issues associated with traditional disposal. Environmental issues specifically related to the coal ash, led to a site specific performance driven approach to management rather than relying on conventional prescriptive approaches. Environmental issues of concern include the leaching of boron and aluminium from ash into groundwater and mine water management systems where both boron and aluminium can occur at elevated levels.   Coal ash exhibits unusual geochemical characteristics reflecting the primary coal composition and the combustion process. The dominant coal type combusted at the Huntly Power Station is derived from Rotowaro and the resulting ash is cementitious and has a high alkalinity. As a result the disposal design is based on the characteristics of the ash itself rather than the material into, or onto which the ash is disposed. Non-notified status was able to be achieved through consideration of these key characteristics of the ash, ensuring that the dimensions of the disposal site and each location was designed to minimise the flow of groundwater through the ash and demonstrating that the physical ash disposal effects are less than minor compared to the consented mining operation.

Jan 1, 2006

I find that during the short time I have been in this district, the majority of boilers are, and have been, receiving very bad usage owing to the difficulties which they have to contend against, viz., oil and bad water. Oil on the heating surface of a boiler is of a highly dangerous nature inasmuch as it allows the surface to become overheated, owing to the water not coming into direct contact with the plates, and it naturally follows that when the crown sheets of a flue or firebox become overheated, you lose a considerable amount of the strength of the plate, and the flue or crown comes down. Referring to the oil question, I find that too much care cannot or exercised on the part of engine drivers in order to minimise as much as possible the internal lubrication of the various engines under their control. For I consider that it is here that the most of the trouble is caused. My reasons for stating such to be the case, are:-That the majority of enginedrivers before coming to this field have been used to driving engines that have been exhausting into the atmosphere, and probably they have been taught that it is far better to use a little extra lubrication than to have a hot bearing. So far so good. But one thing that must not be overlooked is that on these fields the conditions are altered in this respect, as the majority of engines in this district are not exhausting into the atmosphere, but are condensing their exhaust steam and using the water so condensed for feed purposes.

Jan 1, 1901

Australia is the world's leading producer and exporter of mineral sands. Despite increased production from some other countries in recent years, Australia maintained its No.1 position in 1988 among world producers of mineral sands concentrates. Production of the titanium minerals -- ruffle, ilmenite and leucoxene, as well as synthetic ruffle -- by the seven companies currently comprising the Australian industry increased in 1988 in response to continuing strong demand for feedstock by the pigment industry. Production of co-product zircon remained at the 1987 level, reflecting declining zircon grades. Exports of mineral sands concentrates increased in 1988; export earnings exceeded $300million. Prices for mineral sands concentrates are now at a historical high and, assuming that the world economy remains strong, real prices should continue to trend upwards in the short term. Exploration in the Eneabba-Cooljarloo region and the Scott River area, both in WA, the Murray Basin, Vic, and the central Queensland coast area, has identified substantial resources of heavy mineral sands. These discoveries have reversed the trend of the early 1980s of falling resources of mineral sands. In 1988, BMR estimated that economic demonstrated resources (EDR) of ilmenite, rutile, zircon and monazite combined was about 72.8 million tonnes. However, a substantial portion of the resources on the east coast are frozen as a result of environmental considerations. The proportion of mineral sands concentrates processed in Australia increased with the commissioning of two new synthetic rutile plants; Australia is now the world's leading producer of synthetic rutile (total capacity 272000 tonnes), most of it for export. Australia's two TiO2 pigment producers have both increased capacity, lifting national capacity by some 70p ercent to over 120000 tonnes/yr. As part of the expansion one producer converted from the sulphate to the chloride process. Other new pigment plants are being proposed for the future.

Jan 1, 1989