Search Documents

By S. Mostaghel, S. Nicol, M. Y. Solar

Once upon a time, the process engineer developing the design criteria for a new saprolite ferronickel smelter had it easy: most ores were around 2.5% Ni, with a Fe/Ni ratio of 4 to 5 and a SiO2/MgO ratio of about 1.6; to use the French word: garnierites. The ferronickel grade selected was the conventional 20 to 25% Ni and the impurity levels could be predicted from well established [C], [Cr] and [Si] vs (FeO) graphs. However the process engineer can no longer depend on statistics to design smelters: Ni grades are decreasing while the goethite contents are increasing; SiO2/MgO ratios vary from 1 to 3; and Al2O3 concentrations are reaching levels that cannot be ignored. Mechanistic models must be developed to select or predict essential parameters such as kiln and furnace reductions, ferronickel grade, slag losses, metal and slag liquidus, operating temperatures, etc. But these models must be simplified so that they can be used on a routine basis; and they must be calibrated against a wide range of commercial operations in order to yield the most realistic predictions possible. The present paper proposes one possible approach, using FactSage as a basic source of thermodynamic data. The predictions thus obtained are compared to actual performance for two well documented operations, as well as to the predictions made with other tools that might be more accessible.

Jan 1, 2014

By Rob Sloan, Simon Yu, Rob Robison, Mark Schmidt

"In 2000-2009, Highland Valley Copper (HVC) tested new generation 660 mm cyclones supplied by various manufacturers in an aim to replace existing first generation 762 mm cyclones without success. Due to plant infrastructure limitations, new generation larger (838 and 800 mm) cyclones were not feasible. In 2010, an approach of testing hybrid 800 mm diameter cyclones was initiated by HVC. The hybrid cyclone consists of an 800 mm cyclone upper head section and the use of existing 762 mm cyclone conical sections. Three hybrid 800 mm cyclones were engineered and fabricated, targeting a throughput of 850-950 mtph and were installed in the E line cyclone cluster. Since starting operation on September 20, 2011, three hybrid 800 mm cyclones have been running at combined throughput ranges of 750 to 1050 mtph. Based on plant Daily Met Reports, the test hybrid cyclones demonstrated a decrease in misplacement of coarse copper bearing material to the cyclone overflow and better cyclone efficiency when compared to the existing 762 mm cyclones at the same throughput. The hybrid 800 mm cyclones also demonstrated significantly higher capacity per unit when compared to the existing cyclones. Based on the improvement demonstrated in the full plant trials, HVC decided to install the new hybrid 800 mm cyclones in all five grinding lines starting in July, 2012. A more detailed discussion of the full plant trials and initial results of the first complete retrofit of E line will be presented. INTRODUCTIONHighland Valley Copper Partnership (HVC) is Canada’s largest base metals mine and one of the world’s largest producers of Cu-in-concentrate. The mine, located in the central interior of British Columbia, is owned (97.5% interest) and operated by Teck Resources Ltd. In 2011, HVC produced about 210 million lbs. of Cu and 8 million lbs. of Mo. HVC’s Mill Modernization Project (MOP), which was budgeted for $475 M, is currently under intensive construction and is scheduled for commissioning in Q1 2014. The following description was valid at the time of writing this paper.The operation has been expanded a number of times since the startup of the original Lornex mill in 1972. The plant started up with two 9.75 m (32 foot) diameter primary SAG mills. It was expanded in 1981 with the addition of a 10.36 m (34 foot) diameter SAG mill. In 1988, the Highmont concentrator grinding mills and flotation section were moved and attached to the Lornex mill site. This added two10.36 m (34 foot) diameter AG primary mills to the Highland mill. This brought the total number of primary mills to five referred to as Line A, B, C, D and E: three SAG mills (A, B and C) each with two ball mills in parallel and two AG mills (D and E) each with one ball mill. Each AG mill line is equipped with one short head pebble crusher. Ball mill circuits are classified using 8 clusters of ten Linatex 762 mm cyclones to reach a target P80 330 micron (equivalent 43% +100 mesh), before the cyclone overflow product advances to the bulk flotation circuit."

Jan 1, 2013

By Peter A. Adcock, Rob Fraser

Interest in monitoring nucleation overpotential in electrometallurgical processes dates back some 40 years or more. Conversely, remarkable progress has been made in recent years on describing in detail the processes involved in the formation of thin films by electrodeposition. The newer body of work underscores a need for greater clarity in speaking about the role of nucleation and in the acquisition and interpretation of nucleation overpotential measurements – the aim of this paper. In electrometallurgy, it is generally desirable to form deposits that remain smooth, compact, and relatively fine-grained while the deposit grows to a thickness on the order of 5-10 mm, about 100 times thicker than technological thin films. Hence, we distinguish two kinds of nucleation that can result in formation of new grains:- (1) initial nucleation (onto the substrate surface) of islands that coalesce into growing deposit, and (2) ongoing nucleation of new grains on the deposit surface long after the substrate has been covered and ceases to have a direct influence. Nucleation overpotential of the first type should be measured on an electrode surface truly representative of a real industrial substrate. The second type requires judicious choice of electrode material – an “ideal foreign substrate”. In general neither the industrial substrate nor native metal to be deposited is suitable for measurement of the second type of nucleation overpotential, because of interference by other processes. For the future, clear terminology is needed to distinguish these two types of nucleation potential. The second is the one for which the type of plot dubbed by Moats and Derrick as an “Adcock plot” and by us as a “Kerby-Adcock plot” was first conceived and correlated with relatively thick zinc electrodeposits. The data of Moats and Derrick showing trends for copper electrodeposition on stainless steel and on copper electrodes are interpreted within this framework.

Jan 1, 2016

By J. L. Bowlby

The heats of combustion of fuels are determined in the laboratory by means of a calorimeter, usually of the oxygen bomb type. A known weight of the fuel is burned in an atmosphere of oxygen under approximately 400 pounds pressure in a heavy metal container-the bomb- and the heat evolved is imparted to a definite quantity of water. From the rise in temperature, measured by means of a Beckmann thermometer, and other data incidental to the determination, the heat value of the sample can be calculated. On paper, the method appears simple indeed, but in practice the determination of the heat of combustion is one of the most difficult of the various coal analyses. This h as led to considerable investigational work in order to obtain formula: whereby calorific values of solid fuels could be calculated from proximate analysis data al one. The proximate analysis of a fuel consists of the determination of moisture, ash, and volatile matter, with fixed carbon by difference. Sulphur determinations properly belong to the ultimate analysis, but in this section of the country, where the sulphur content of the coal is comparatively high, a request for the proximate analysis of a fuel implies the determination of the sulphur as well.

Jan 1, 1929

By Fred W. Brackebusch

"The use of paste technology for surface tailings disposal may offer economic, technical, safety, and environmental advantages for both underground and surface mining operations. Paste is a non-Newtonian fluid having some shear strength during transport and placement. The strength is augmented after placement by consolidation, water loss, and by addition of chemicals. Economical dewatering systems are necessary to the success of surface paste tailings disposal. In an underground mine, the paste backfill plant can produce paste for surface disposal about 50% of the time because only about 1/2 of the tailings are needed for backfill. The distribution of paste to the surface stack involves expensive pumping equipment and thus a nearby location of the stack is desirable. The viscosity of paste can often be manipulated by modifying pH. Placement of the paste in a designed stack configuration depends on topographic and climatic factors as well as paste properties.INTRODUCTIONThe use of paste technology for mine backfill is becoming accepted for underground mines mainly because of ground control and economic reasons. Paste technology is just starting to be applied for tailings disposal with only a few hardrock metal mines worldwide using the technology; however, it has been used extensively for red mud disposal in the aluminum industry. The disposal of dry tailings is very attractive from environmental and safety points of view because of limited water which might potentially escape and pollute river systems. Dry stacking systems, however, are expensive because of filtration and truck transportation costs. Paste can be produced from most tailings streams by special types of thickeners. Furthermore, it can be transported in pipelines, therefore paste technology may be more economic than dry stacking but still have some of the major advantages. Understanding of paste technology has improved through experience with operating underground backfill systems in recent years and because of testwork and research programs by mining companies, consultants and equipment vendors. Thus we may be on the verge of taking a new look at tailings management using paste technology."

Jan 1, 2002

By Martin Nevens

"In 1998, the Iron Ore Company of Canada initiated an aggressive program to improve the performance of its Carol Lake Concentrator located in Labrador City, Newfoundland. This program was termed the Concentrator Upgrade Program. The Concentrator Upgrade Program was a group of initiatives developed with the common goal of improving the overall process and operations of the IOCC Carol Lake Concentrator. The main goal of the program was to increase the annual production capacity of the concentrator from 18.0 million tomes to 21.6 million tomes. This gain in capacity was to be done mainly through improvements in process iron recovery. The target iron recovery value was 80+% versus a historical value of 70%. This improvement in iron recovery would translate to a natural weight recovery improvement from 44% to 50%.The Concentrator Upgrade Program provided the first opportunity in 30 years to make fimdamental changes to the concentrator flowsheet. To accomplish this, several pilot plants were built to evaluate new circuits. AAer 2 years, a new flowsheet was selected for the primary gravity separation circuit and the magnetite circuit. The centrepiece of the new flowsheet was the introduction of Hindered Settling Separators to the metallurgical process.The Concentrator Upgrade Program has since proceeded into detailed engineering and, as of February 2001, construction. The first one of IOCC’s 3 primary AG Mills (Mill 11) has been converted to the new flowsheet at the time of writing and is in the throes of commissioning. This paper will review the flowsheet development program in the pilot plant for the gravity separation circuit and examine the overall benefits to the operation of the IOCC Carol Lake Concentrator."

Jan 1, 2002

By Georgy A. Cherkashov, Andrey V. Efimov, Yury S. Borodaev, Nadezhda N. Mozgova, Sergey G. Krasnov, Tamara V. Stepanova, Alexander M. Ashadze

"Abstract - A horizontal mineralogical-geochemical ore zonation with a southeast to northwest trending succession of Cu and Fe (Zn) main zones has been discovered in the Logatchev hydrothermal field (14°45??N Mid-Atlantic Ridge). The major minerals are pyrite, chalcopyrite, bornite, isocubanite, digenite and chalcocite. Zn-sulfide, marcasite and covellite are less abundant. Rare minerals are native copper, zincian copper and cobalt pentlandite (first found in oceanic massive sulfides), Cu and Cu-Co-bearing Fe-disulfides. Two groups of the main sulfide assemblages with different copper contents are recognized: Group I comprises assemblages with primary sulfides (isocubanite, chalcopyrite, pyrite and Zn-sulfide; Cu up to 35 wt% in Cu-bearing minerals); Group II contains assemblages with secondary Cu-rich sulfides (bornite, digenite, chalcocite; Cu ~60 wt%) as well as rare minerals (cobalt pentlandite, native copper and zincian copper). The assemblages of Group I formed at a temperature of about 300°C; the sulfur fugacity (log fs2 atm) at 300°C is probably 9.9. Relations between minerals of this group are contradictory, attributed to non-equilibrium environments, and no unified sequence of crystallization of minerals has been determined. Minerals of Group II replace, rim or cross the assemblages of Group I. Group II minerals crystallized in a distinct sequence (cobalt pentlandite-bornite-digenite- chalcocite-native copper), with increasing copper content from the start to the end of the depositional sequence. This may correspond to pH from 7 to 8 near Eh = -0.2 at 250°C. Minerals of this group were generally formed under hypergene alteration processes. Compositions of ore minerals were studied by means of electron microprobe analysis (EMPA) (150 analyses). Narrow composition fields were revealed in all main sulfides, which comprised known experimental data. ZnS contains 6.0 to 28.0 mol.% FeS, which is close to data known for other hydrothermal massive sulfides from the Mid-Atlantic Ridge (MAR). A common admixture in ZnS is Cu (0.16 to 1.32 wt%). Rare grains of unusual anisotropic Fe-disulfides, (Fe0.95Cu0.05)S2 and Cu(Fe,Co)9S20, were found among the ore minerals."

Jan 1, 1999

By A. J. MacRae

Metallurgical furnaces are made up of complex multi-component systems that must function either together or in parallel for safe, and reliable operation. Thermal expansion of single material components experience induced stresses during heating and cooling, which can lead to cracking or failure. Multi component elements and systems can experience significant thermally induced stresses during both steady state and transient temperature conditions. Examples pertaining to temperature effects on refractory, copper cooling blocks, furnace shells, and complete systems will be discussed. The purpose of the paper is to highlight how stresses and strains are developed due to differential thermal expansion.

Jan 1, 2015

By John Lindsay

Outline ??Recovery plant requirements and concepts ??Common recovery plant unit processes ??Recovery plant design considerations ??Peripheral issues Process Design ??Liberation ??Separation ??Recovery Processing ??Density 3.5 g/cm3 ??Luminescent under x-ray ??Hydrophobic (non wettable) surface ??Non-magnetic ??Inert to strong acids / bases

Apr 1, 2005

By J. Allaire, P. N. Muteb

The Meadowbank mine is operated by Agnico-Eagle Mines Ltd. and is located in the Kivalliq District of Nunavut in northern Canada. The process plant operates presently at a throughput of 11,500 tpd with gold grade varying between 2.9 and 3.6 g/t. The ore supplied to the process plant come from two different open pits and it expected to come from a new open pit early 2014. The ore is mid-hard materials so the feed size ore have a bigger impact on the throughput. The average gold recovery is 94.0% with about 15-30% of gold recover from the gravity circuit. The Meadowbank mine commissioning started in February 2010 utilizing a flowsheet consisting of one stage of crushing followed by primary and secondary grinding. The commercial production began in March 2010. During the commissioning several difficulties were observed to reach the designed throughput of 8,500 tpd. It was evaluated to insert a second stage of crushing. The insertion of the secondary crushing have two objectives, first to reach easily the process plant design throughput as well as to evaluated the mill capacity increasing. The process plant team evaluated various expansion alternatives eventually deciding to install a secondary crusher, increased the SAG and Ball mills motors capacities and maintain the rest of the process unchanged. Early 2011, with the improvement in the gold markets, decision was made to install the secondary crusher between the primary crusher and the primary grinding. The process plant continued to operate on the initial design until early June 2011. This paper presents the SAG mill throughput increasing from the designed tonnage of 8,500 tpd to 2012 targeted tonnage of 11,500 tpd, secondary crusher commissioning and the difficulties to operate in Canada Artic (Nunavut).

Jan 1, 2013

By Filip Rochette, Yvan De Busscher

Extraction of minerals can be achieved by a variety of technologies; one of them is ion exchange. There are several ion exchange configurations and mechanical set-ups available, but only one technology will provide more process performance and flexibility compared to the other. The multiple column Continuous Countercurrent Ion Exchange (CCIX) technology provides the highest form of process flexibility with also the highest mineral recovery feasible through ion exchange. In comparison with a fixed bed system, the PuriTech CCIX system offers the benefits of continuous counter-current contact mode. This way the resin capacity is fully exploited leading to reduction in resin inventory and, at the same time, in chemicals and water consumption, and product dilution. For any set of operating conditions the mass transfer zone has a characteristic length (MTZL). The MTZL can be expressed in duration, column length, or volume, but is the measure of the quantity of resin in the system that is doing "work" at any given moment in the process. The objective of continuous ion exchange processing is to eliminate all resin volume from the process equipment that is not within a mass transfer zone. In most commercial ion exchange processes for the recovery of metals, CCIX engineering can eliminate as much as 20 - 80 % of the ion exchange resin inventory. Consumptions of water and chemicals are typically brought down around 40% or more. For each type of resin the selectivity/affinity towards a particular metal depends on the basic process conditions such as pH, concentrations of other competing metals in solution. By changing the pH in the ion exchange process phase, the selectivity of the resin can be changed. By doing this, a split elution, or extraction of metals separately can be achieved and the effect of other competing metals (cross-contamination) can be reduced. For example the DOW resin XUS43578 is commonly used for the recovery of copper or nickel/cobalt separation.

Jan 1, 2016

By Steven Townend

Mining-related activities have been known to create a challenging operating environment for mining companies located in close proximity to communities. Issues such as noise, vibrations from mining operations, land use and emissions are often a concern for community residents. In order to develop good community relationships it is necessary to take a proactive approach. This paper documents this approach and also deals with the social implications for Vale associated with mining activities in the heart of the community of Copper Cliff, Ontario, Canada.

May 1, 2011

By I. P. Barbosa, P. S. M. Soares, I. O. C. Masson

"Permanent magnets have been applied extensively to several electronic products such as printers, TV sets, microphones, microcomputers and headphones, presently manufactured in large scale by industrial economies. Sm-Co alloys represent about 20% of the world market for permanent magnets and their industrial processors generate 20-30% of magnetic scraps which can be recycled. This paper discusses a process route to recycle SmCo5 using acid treatment, solvent extraction of Sm and electrowinning of Co. The results confirm the feasibility of the alternative proposed. Basic operational variables are suggested as guidelines to design a plant for recycling magnetic scraps.The use of hydrometallurgical processes to recycle scraps from the industry of permanent magnets has been suggested in some recent papers related to recycling of metallic alloys [ 1 ]. These research efforts might be understood as a worldwide tendency towards the development of self sustainable metallurgical processes which mean the reduction of environmental impacts.CETEM -Center for Mineral Technology leads in Brazil several research programs concerning recycling and treatment of industrial residues. The work on samarium purification and concentration by solvent extraction, producing also a solution of cobalt sulfate as partially reported here is one of these programs. Previous results related to the sulfuric acid digestion of SmCo5 are presented somewhere else [2]"

Jan 1, 1997

By Neil McMillan

"By any measure of common practice, Claude Resources' Seabee Gold Mine in Northern Saskatchewan should not now be operating. Not because reserves dwindled, or grade dropped or prices weakened or technical problems arose, but because a host of unimaginable other problems beset the project, any one of which would normally have led to the mine's failure.The success of the Seabee Mine, and it is extremely successful, is a story of the vision and blunt determination of two men. Neither is remarkable in his own right but each possesses the characteristics which were necessary to forge a highly productive and profitable narrow-vein mine in the midst of the most bizarre and unpredictable events which likely have ever beset a mine start-up in Canadian history.Together, Bill MacNeill, a Saskatchewan born, former bush pilot and Ray Gagnon, a big hearted, hard-fisted, miner with 44 years of experience in Canada's underground, built the Seabee Mine.They didn't accomplish this with brilliant geology, outstanding engineering or nimble corporate manouvering but rather a stubbornness and raw common sense which likely are all too often, ingredients missing in failed projects.The Seabee Mine is 100% owned by Claude Resources, a Saskatoon based company taken over by Bill MacNeill, its current chairman, in 1982. The company is listed on the TSE and produces 1200 barrels of oil per day and about 60,000 oz of gold per year. The company has a strong balance sheet, is very profitable and has 18 million shares outstanding.The Seabee property in Northern Saskatchewan started out like many other gold exploration properties in Canada.It was discovered in the l 940's by what is now Cominco, and, while highly regarded by that company the property sat largely dormant until acquired by Claude Resources in 1985.Claude did what most junior exploration companies would do and went looking for a company with a depth of expertise to joint venture the property.That company was Placer Development who could earn a 55% interest in the Seabee by delivering a bankable feasibility study on the Project by July 1988 and providing financing to production.Placer Development was an excellent company and spent over $8 million dollars on the Seabee over a 3 year period. Unfortunately for Claude Resources, Placer Development merged with Dorne Mines in 1987 and the new merged company, Placer Dome, established a minimum production threshold greater than the 50,000 oz per year which the Seabee appeared capable of supporting at that time. Placer Dome's request for an indefinite extension of the joint venture agreement to allow it to drill off a larger ore body was rejected by Claude Resources and the Seabee Property was returned to Claude in 1988."

Jan 1, 1998

By Charles A. Taschereau

Burkina Faso ? Formerly known as Upper Volta; Country is landlocked and dry (Sahel sub-Sahara zone); ? Among poorest countries in the World, according to the United Nations Human Development Index (in 2005, 178 out of 179 countries; in 2009 173 out of 179); ? Population 13,9 Millions; Life expectancy is 51.4 years; Fertility rate 6.47 children/woman; Average age is16 years; literacy rate 23.6% and GDP per capita $1,213; ? French is official language; Politically stable country; very low criminality rate; corruption level low. Multiparty elections since early 90s; Legal and political systembased on French civil law system; ? Country just opened a few years ago to International mining companies, with a new mining code and investment code; ? No experienced labour; ? All new codes and laws; no established practices; Very limited economic development, mining is already main product of exportation and the country will become with Essakane a mineral economy (over 50% of total exports from mineral sources);

May 1, 2010

By Michel Aubertin

Les haldes à stériles contenant des minéraux sulfureux réactifs constituent un milieu favorable à la production du drainage minier acide (DMA). Au sein de ces haldes, les processus physiques, géochimiques et biologiques qui mènent à la production du DMA sont nombreux et complexes. Un des aspects critiques qui affecte la génération de DMA est la distribution et le mouvement de l?eau dans les roches stériles. La modélisation numérique est un outil qui permet de comprendre, pour éventuellement contrôler, les mouvements de l?eau (et donc réduire la production du DMA) dans les haldes pendant la période d?exploitation de la mine et à sa fermeture. Plusieurs simulations numériques des écoulements non saturés dans des haldes ont été effectuées. Pour ces simulations, on a considéré divers types de matériaux, diverses conditions atmosphériques et diverses configurations géométriques. Les simulations réalisées montrent que l?on peut contrôler les mouvements de l?eau en introduisant des couches de matériaux fins intercalées dans les haldes formées de matériaux grossiers. Des couches horizontales ne sont cependant pas appropriées puisqu?elles peuvent, dans certains cas, favoriser la création de zones humides susceptibles d?amplifier les effets du DMA. Une faible inclinaison des couches de matériaux fins vers l?extérieur permet de palier à ce problème. Les couches inclinées favorisent un drainage des haldes vers la périphérie. Ceci a pour effet de garder sèche une grande partie des stériles et de réduire, par le fait même, la production du DMA.

Nov 1, 2002

By Norman O. Lotter

The problem of quantifying the full performance potential of an ore body in a concentrator, and how to configure a flowsheet to achieve that potential, either for a new operation or an existing one, is a strategic challenge. Modern flowsheeting technology that has been developed over the last twenty years has provided a suitable platform to achieve this. The integrated use of geology, compositional and quantitative mineralogy, sampling models, quality controls, and mineral processing, including flotation testing, has evolved into what is now called process mineralogy. Two specific tools have been developed and validated as standard methods in this toollbox. These are statistical benchmark surveying and high-confidence flotation testing. Both of these have borrowed from the sampling theories of Pierre Gy and from geostatistics. Additionally, they work on a replicate measurement and averaging basis, thus reducing the overall random error level. With this arrangement, one is in a position to characterize the ore from true samples and identify and quantify the economic minerals present in a manner that easily brings out the processing implications and likely grades and recoveries. In particular, the approach captures the variation in the ore body, which, if properly translated into the flowsheet design, minimizes the risk that unexpected responses will develop in the concentrator operations. A further advantage is that successful plant trials are now possible and practical. An overview of this approach is presented with two case studies.

Jan 1, 2011

By Tony Lipiec, Chris Fleming, Larry Urbanoski

In 2009, the Canadian Mineral Processors (CMP) became aware that Canadian securities regulators were amending the contents of National Instrument 43-101. NI 43-101 is a set of regulations which establish how ore resources and reserves are presented to the investing public. The documents produced under NI 43-101 are central to the ability of many companies to raise financing for their projects. With the increase of metallurgical complexity, and decrease of head grades encountered in new deposits, the role of the Qualified Person (QP) in determining process performance has become increasingly critical in determining the classification category of resources and reserves. Given the challenges confronted by those involved in defining the concentration and extraction of minerals and metals, there is a need to provide support to these QPs. To address these concerns, the CMP established a sub-committee in 2010 to create a set of guideline documents to assist the QP involved in process matters as to what should be included at the various levels of study supporting the establishment of resources and reserves in NI 43- 101. The results of the sub-committee work are presented and the considerations in the writing of the documents are discussed.

Jan 1, 2011

By M. W. Grabinsky

Better in situ performance data is required in order to advance the rational geomechanical design of cemented paste backfill systems. A few in situ test programs have been conducted, but these have suffered from too few measurement locations within the stope and have not used enough different types of transducers to fully capture the information of significance. In this paper the important geomechanical design aspects are listed, the underlying physical phenomena are described, and some previous in situ measurement efforts are reviewed. A new approach to in situ measurement campaigns is then described including measurement techniques, locations, and the logistical aspects of mobilizing transducers in an active mining environment. A work-in-progress is used to illustrate the principles and concepts involved.

May 1, 2007

By C. Larsen, I. Orford, L. Strah, M. Renaud, P. Radziszewski

"An AG/SAG mill was commissioned at the Brunswick mine concentrator in October 1998. This paper discusses the original shell top hat liner design for the bi-directional AG/SAG mill, observed liner wear, subsequent liner design modifications, and benefits.The original liners were chrome-moly steel Norsteel with rubber grates and rubber-lined pulp lifters. The design was based on experiences of other AG/SAG mills and recommendations by the liner supplier, Norcast. Liner design modifications were made in an iterative fashion after observing the wear rate profile of the liners; over ten liner sets were implemented. Shell liner design improvements were supported by a design of experiments approach in conjunction with discrete element method (DEM) charge motion simulations. Design optimization took into account lining costs and impacts on operating performance. The team approach to the liner design improvements process is described with emphasis on the application of the design of experiments. The liner wear history and mill operating performance are presented."

Jan 1, 2005