Search Documents

By S. Rajeswari, D. Gopi

"Pitting corrosion inhibition of 304 stainless steel (SS) in groundwater with a ternary inhibitor mixture (phosphonic acid + bivalent cation + various surfactants) was studied with different environmental variables such as temperature, pH, dissolved oxygen and chloride ions. Critical pitting potential and corrosion potential were calculated for these test media using electrochemical techniques. Under the tested condition, the localized corrosion resistance of 304 SS was determined and the results are discussed. IntroductionPitting corrosion of metals and alloys is a major cause of failure in chemical processing desalination plants, scrubber for flue gas desulphurization (FGD) plants, water storage tanks and pipelines, petroleum refineries, etc.Heat exchangers and condensers in inland thermal and nuclear powerplants utilize groundwater as a coolant, but materials of construction are generally prone to localized corrosion.Localized corrosion attack can be initiated when the passive film on the metal is disrupted. The presence of certain aggressive anions such as chlorides (Cl-) can migrate to the actively corroding area and stabilize pitting corrosion. Attention has been focussed on improving the resistance of stainless steel against localizedcorrosion in aqueous environments.One of the most accepted methods of avoiding corrosion is by the addition of chemicals (inhibitors). Over the past two decades, some phosphonic acids have been explored due to their good corrosion inhibition efficiency and low toxicity (Fang et al., 1993; Karman et al., 1998; Rajendran et al., 1998; Gopi and Rajeswari, 2000a). Bivalent cations like Zn2+ are often applied as additives to inhibit the metal dissolution (Sekine and Hirakawa, 1986; Aruna Bahadur, 1998)."

Jan 1, 2003

By W. M. Scheding

"There has recently been a resurgence of interest in unit flotation of mill discharges. At the Kidd Creek concentrator, this technique has been successfully applied to silver flotation in a 3050 mtpd silver-copper-lead-zinc division. The major incentive has been improved silver payment through increased overall recovery and better distribution between the sequential copper, lead and zinc concentrates. A large, but variable fraction of the silver in the ore is present as native silver and, being dense and malleable, is susceptible to overgrinding. Grinding circuit surveys showed high concentrations of silver in both primary and secondary circulating loads. Laboratory testwork confirmed that this was selectively flotable, identified the secondary ball mill discharge as the best feed stream and optimized flotation conditions. A 10 t/h pilot plant campaign confirmed that the rate of accumulation of silver was sufficient to sustain continuous production of a silver concentrate and that flotation of the whole stream was not necessary.The present 30 t/h production circuit recovers from 5 to 50% of the silver in the ore at a concentration ratio between 25 and 250. The circuit also contributes to a better understanding of ore mineralogy, as an 'on-line' indicator of elemental silver content."

Jan 1, 1985

By R. F. Pilgrim

"This first chapter of the SPOC Manual 1s intended as a general introduction to all the other chapters in which the mineral process evaluation and optimization methodology is presented. This chapter also provides a brief description of available software for mainframe and m1crocomputers and provides information on its distribution by the Technology Information Division. CANMETRESUMECe premier chapitre du manuel SPOC est un guide général qui présente les autres chapitres ou l'on traite de la méthodologie d'évaluation et d'optimisation des procédés miméralurgiques. Le lecteur y trouvera aussi une description sommaire des programmes de calcul développés pour ordinateurs centraux et pour micro-ordinateurs ainsi que la façon de les obtenir de la Division de l'information technologique du CANMETComputer simulation of mineral processes has slowly emerged as an established branch of activity in A&D centres and in several teaching institutions after decades of slow progress. Substantial efforts to develop application software based on years of research on process modelling are being pursued in many countries ( 1 .2,3,4.5). The late BO's should see a flurry of success stones about significant leaps of productivity achieved in several plants through systematic process evaluation and computer simulation studies.In Canada. the SPOC project (Simulated Processrng of Ore and Coal) was initiated at CAN MET in 1980 with the obJective of developing and transferrrng to the mineral rndustry a computer-based methodology for process evaluation and optimization. The proiect deliverables include:- an engineering manual covering most aspects of off-line computer simulation:- a bank of FORTRAN software accessible through data communication lines for user familiarization and distributed at a nominal cost in source form by CANMETThe yearly progress reports of the project contain detailed information on the project elements since 1980 16). The context of SPOC can be summed up by quoting Gordon Agar""s 1975 statement during a workshop on research needs in the mineral industry: ""What is needed is a joint effort between the academic community and one or more enliglitened industrial concerns. The effort will have to be an iterative one with data collection followed by testing the model modification of the model (s), more testing prediction, modification. data collection and so on (7). A few parallel in1- t1atives had been reported in papers or research contract reports (8, 9) but there was an obvious need for CANMET to bridge the gap between the R&D and the production sectors by undertaking a project that would document past applications and induce a new generation of initiatives through the consol1dat1on and transfer of suitable manuals and software. The effort took shape as the CANMET SPOC pro1ect in which methodology transfer was to play a key role (10)."

Jan 1, 1986

By A. Lloyd, Montgomery, J. Jorgesen, W. J.

"Coals are ranked according to their degree of metamorphism or progressive change in the natural series from lignite to anthracite. The reader is referred to ASTM Standard D-388, ""Standard Classification of Coals by Rank"" for a detailed description of the system in use throughout North America including Canada.Fixed carbon and calorific value (expressed in Btu/ lb) calculated to the mineral-matter-free basis have been chosen as the main characteristics from which rank is established. Higher rank coals are classified according to fixed carbon content, lower rank coals according to the calorific value on a ""moist"" mineral-matter-free basis. Certain adjacent groups are differentiated according to their agglomerating (caking) properties. ""Moist"" refers to inherent moisture. Referring to Table 1, coals having calorific values greater than 14,000 Btu/lb on a moist mineral-matter-free basis and fixed carbon of 69% or more on a dry mineral-matter-free basis are classified according to fixed carbon. Coals having calorific values of less than 14,000 Btu/lb on a moist mineralmatter-free basis are classified according to calorific value on a moist mineral-matter-free basis. Agglomerating coals having 69 to 86% fixed carbon on the dry mineral-matter-free basis are classified in the low or medium volatile group of the bituminous class according to their volatile matter content. Agglomerating coals having calorific values between 10,500 and 11,500 Btu/lb are classified in the high volatile C bituminous coal group; nonagglomerating coals in the same calorific value range are classified in the sub-bituminous A coal group."

Jan 1, 1985

By Göran Bäckblom

The Swedish mining companies LKAB and Boliden, the equipment supplier Atlas Copco, the general contractor NCC and the specialist company Reflex joined forces in 2005 to advance the field of rock technology for the purpose of mining and underground construction. The creation of the company Rock Tech Centre is part of the strategy developed by the Swedish mining industry to strengthen co-operation with industry, academia and society. This paper outlines the current R&D strategies developed for the industry in general, discusses what focus areas are selected and provides some details on the current RTC project portfolio, especially faster and better drifting.

May 1, 2006

By M. B. McClenaghan

"This paper summarizes diamond exploration techniques used in glaciated terrain, focussing on indicator mineral and geochemical methods applied to glacial sediments. Understanding the ice flow history, depositional history, and stratigraphy of glacial sediments is essential to successful sampling, interpretation and follow-up of indicator mineral and geochemical anomalies related to kimberlites. Kimberlite indicator minerals survive glacial transport over long distances and the relative abundance of each mineral in till is a function of the primary mineralogy of individual kimberlites. Indicator mineral distributions observed at a regional scale define the net effect of glacial dispersal, often along different ice flow directions. Local-scale distributions define individual dispersal trains. The medium sand (0.25 mm to 0.5 mm) fraction of heavy mineral concentrates, * GSC Contribution No. 2002028 prepared from glacial sediment samples, is best suited for indicator mineral surveys. The application of till geochemistry to diamond exploration is increasing because it is significantly cheaper than indicator mineral analysis and it can be performed quickly. The <0.063 mm (silt+clay) and 0.5 mm to 2.0 mm (coarse sand) fractions provide the best geochemical contrast between background and kimberlite-rich till. Kimberlite pathfinder elements that provide good contrast include Ni, Cr, Ba, Co, Sr, Rb, Nb, Mg, Ta, Ca, Fe, K, Ti and LREE, the relative importance of which will depend on kimberlite composition and that of the surrounding bedrock.IntroductionIn Canada, glacial erosion is the principal means by which kimberlite and its associated minerals have been dispersed, from a few tens of metres to tens of kilometres down-ice. Post-glacial weathering has had little impact on kimberlite debris in the glacial sediments, thus boulder tracing, indicator mineral methods and trace element geochemistry of the fine fraction of till (“drift prospecting” methods) can be used to detect kimberlite dispersal within areas covered by glacial sediment. This paper provides a summary of drift prospecting methods for kimberlite exploration in glaciated terrain, and includes examples of reconnaissance- , regional- and local-scale kimberlite indicator mineral and till geochemical distribution patterns.Weathered kimberlite is more susceptible to glacial erosion than the surrounding bedrock, thus many kimberlites in glaciated terrain are found in low or swampy ground, under small lakes, or covered by thin (< 1 m) to thick (>50 m) glacial sediments. Glacial erosion has removed varying amounts of the pre-glacially weathered kimberlite and, in some cases, the hard competent kimberlite below. For example, glacial erosion of the Peddie, McLean and Seed kimberlites near Lake Timiskaming, Ontario, removed pre-glacially weathered kimberlite, leaving a polished striated subcropping surface (McClenaghan et al., 1999a). In contrast, glacial erosion of the B30 kimberlite, near Kirkland Lake, Ontario (Fig.1), was much less vigorous and left a >10 m cap of soft and highly weathered dark green clay-rich kimberlite (McClenaghan et al., 1996). The thickness of remaining pre-glacially weathered kimberlite will influence the geophysical signature of the kimberlite."

Jan 1, 2002

By M. Cai

A practical simple method is proposed to estimate the tensile strength (st) of strong brittle rocks from the strength ratio of R= sc/st = 8 sc/sci, where sc is the uniaxial compressive strength and sci is the crack initiation stress in an uniaxial compression test. 8 is the Griffith strength ratio and the term sc/sci accounts for the difference of crack growth or propagation in tension and compression in uniaxial compression tests. sci can be reliably obtained from volumetric strain measurement or acoustic emission (AE) monitoring. With the strength ratio R determined, the tensile strength can be indirectly obtained from the result of uniaxial compression tests. In addition, a practical estimate of the Hoek-Brown strength parameter mi is presented and it is suggested that mi = 12 sc/sci can be applied to strong, brittle rocks in high confinement zone and mi = 8 sc/sci can be applied to low confinement to tension zones. It is found that the predicted tensile strengths and Hoek-Brown strength parameter mi using this method are in good agreement with test data. The rock strength parameters like st and mi, which require specialty tests such as direct tensile (or Brazilian) and triaxial compression tests for their determination, can be reasonably estimated from uniaxial compression tests.

May 1, 2009

By Luis Magallanes-Hernández

"Industrias Peñoles, S.A. de C.V. (Peñoles) in Mexico, is a major silver producer. The Peñoles Mining Division has eight Mining Operations and in seven of them, flotation is used to concentrate the metal and mineral values. Common metals and minerals values are: metallic gold and silver, gold-silver alloys, silver sulphide minerals (acantite, pyrargirite, argentite, proustite); lead sulphide mineral, galena; zinc sulphide mineral, sphalerite; and copper sulphide minerals (chalcopyrite and bornite).In the last years, a special emphasis has been given to using modal analysis to identify ore mineralogical limitations, in order to direct efforts into key areas where opportunities exist to improve the metallurgical results.This work aims to share Peñoles mineralogical and metallurgical results, through presenting, discussing and drawing conclusions on these results; as well as pointing out areas where more work is needed to improve the Concentrator´ performance.PEÑOLES BACKGROUNDPeñoles´s mission is to add value to non-renewable natural resources on a sustainable manner. It was established in 1887, and it is a mining group with integrated operations in smelting and refining non-ferrous metals, and producing chemicals. Peñoles is the world’s top producer of refined silver, metallic bismuth, and sodium sulphate, the leading Latin American producer of refined gold, lead, and zinc.Peñoles Mining Division is integrated into eight mining business, located on five different states in Mexico. Metal productions for the Mining Division during 2003 were: 343 thousand gold ounces, 48.4 million silver ounces, 81.3 thousand tons of lead, 235.1 thousand tons of zinc, and 10.6 thousand tons of copper."

Jan 1, 2005

By J. Dong

"Xanthate is a sulfide collector that has been widely used in flotation for almost a century. It is inexpensive, easy to synthesize and apply, and produces good metallurgy in the right applications. However, a major drawback of xanthate is that it decomposes easily and generates CS2 gas in transportation, storage and operation, which can be harmful to human health. Also, excessive xanthate in tailings pond leads to toxicity of the process water and potential damages to aqua-life systems. New regulations in Ontario require that the TWA (time-weighted-average) value of CS2 in the work place is below 1 ppm, which is 1/10 of the previous limit. The stringent regulation may eventually sweep other regions of Canada with the increased awareness of healthy working conditions and environment protection. Therefore, it becomes very important to find xanthate replacements which will be “green”, i.e., environmentally friendly.In this research work, a systematic procedure is used for collector evaluation using the Sudbury nickel sulfide ores from Vale’s Ontario operations, starting with the collector properties (MSDS) evaluation, followed by batch flotation tests, miniplant tests, plant trials and economic evaluation. It is found that the most promising xanthate replacement is dithiocarbamate.INTRODUCTIONSulfide mineral flotation has been practiced since the early 20th century. Its industrial importance is well recognized as mineral concentrates from flotation can be economically smelted and refined to provide primary metals. Collectors play a vital role in froth flotation. There are reagents possessing both a polar group that binds them to the mineral surface and a nonpolar group that is oriented away from the surface to attach air bubbles. The introduction of xanthate as a sulfide collector in 1925 was a remarkable development in froth flotation (Keller, 1925). It is low cost, easy to synthesize, water soluble, simple to control in application. Most importantly, it has strong capability and usually good selectivity for sulfide mineral flotation, which have been keeping its application prominent for almost a century."

Jan 1, 2011

By T. G. Joseph

A strain-softening constitutive relationship is introduced that describes the post-failure stress-strain curve for rock regardless of whether the rock is intact or broken. The core of this relationship is an ?apparent friction? concept that relates the post-failure apparent cohesive and frictional characteristics of the rock to the strain. The relationship can be determined for a given rock via a series of tri-axial strength tests establishing the peak strength and corresponding strain for a range of confining pressures, together with the determination of the base angle of friction via a simple tilt test. The postulates and assumptions used in deriving this relationship are verified from results of tri-axial tests on both intact and broken rock.

May 1, 2002

By Turgut Yalcin

"High-grade concentrates are achieved in flotation columns primarily due to the use of thick froth layers and wash water, both of which facilitate the drainage of hydrophilic minerals from the froth. However, conventional columns employ tall, non-agitated recovery sections for bubble-particle attachment that require high headroom and special gas spargers as well as imposing particle size limitations. These disadvantages can be all alleviated by carrying out the recovery part of the process in a mechanical or pneumatic cell which generate froth more conveniently and efficiently.This paper describes the combining of mechanical and column flotation in a single unit and discusses the influence of various parameters on the performance of the system.INTRODUCTIONIn a flotation process, some of the minerals lifted up to the froth phase may drain back to the pulp due to various reasons such as weak attachment of particles to air bubbles, bursting of air bubbles, agitation of froth, etc. Weakly floating and entrained hydrophilic minerals drain at a faster rate than the strongly floating minerals, and effective exploitation of such differential drainage can lead to cleaner concentrates.For a given mineral, if the rate of flotation from pulp to froth is k1 (min·1) and the rate of drainage from froth to pulp is k2 (min""1), then the net (overall) flotation rate of the mineral, k (min-1 ), will be [Lynch et al., 1981 ]:"

Jan 1, 1997

By K. Hoover, G. Labarre, S. Rantanen

"As part of the Namew Lake project a mill was constructed to treat 1900 tpd of ore grading approximately 0.90% CU and 2.45% Ni to produce copper and nickel concentrates.Nickel occurs mainly as pentlandite and violarite while copper occurs as chalcopyrite. Two main ore types are present1 lower grade disseminated sulphides in a talcose ultramafic gangue and a higher grade solid sulfide with a granitic breccia matrix.Primary crushed ore from underground is treated on surface in a conventional closed circuit crushing plant using 2-stage cone crushing. Crushed ore is conveyed to storage and then fed at a controlled rate to a grinding circuit employing a rod and ball mill with hydrocyclone classification. Rougher flotation separates and cleans nickel and copper sulfides from waste materials followed by a high lime separation circuit to separate the minerals into final concentrates. Dewatering is achieved through use of high capacity thickeners and pressure filters prior to delivery to a loadout area. The crushing and milling control is highly automated.Plant design was based on metallurgical samples obtained from drill cores. After the first year of operations, plant results compared favourably with design projections.INTRODUCTIONThe Namew Lake Project is a joint venture partnership between Outokumpu Mines Ltd. (Canada) and Hudson Bay Mining and Smelting Company Ltd. (60%). The project included construction of a mine and milling complex to treat approximately 500,000 tonnes per year of copper-nickel ore grading o.91% and 2.44% Ni. Known reserves are estimated at 2. 65 million tonnes. The deposit is located approximately 65 km south of Flin Flon (120 km by road) and about 5 km east of the Manitoba-Saskatchewan border. The decision to construct a concentrating facility was made June 15, 1987 and construction started a week later. The facility, designed for 1900 tonne per day throughput, was ready for commissioning in September 1988. Outokumpu Engineering of Finland was chosen to prepare metallurgical flowsheets, select and develop plant layouts, and provide construction management. Kilborn (Toronto) contributed detailed engineering for civil, structural, mechanical and electrical components and outokumpu Equipment of Canada, the design, the supply, and commissioning of the instrumentation package. Hudson Bay undertook the initial metallurgical test work and preliminary design work."

Jan 1, 1990

"Gravity concentration remains the main separation method for fine iron ore and is used extensively for treating various minerals. Gravity concentration methods separate minerals of different specific gravity by their relative movement in response to gravity and one or more other forces, the latter often being the resistance to motion offered by a viscous fluid, such as water or air (Wills, 2006).Spirals concentrators are one of the gravity concentration equipment used for beneficiation of minerals. Spirals are typically used for processing of fine minerals (-1mm) size fraction. The main operating variables for a spiral concentrator are the feed rate, the solids concentration, the wash water addition and the position of the cutters or splitters used to separate the tailings, middling and concentrate streams (Sadeghi, Bazin & Renaud, 2014).The aim of this study is to investigate the effect of feed rate, solids concentration and wash water on grade and recovery on iron ore material. The Multotec SC20HC/7 WW spiral was used for the experimental test work. The spiral was tested at varying solids concentration and feed rate. The wash water rate was also varied to establish the best washing rate. The splitter positions were kept constant. Optimization of these variables is expected to provide optimum conditions for a good compromise between grade and recovery.INTRODUCTIONSpiral concentrators are simple low energy consuming devices that separate minerals mainly on the basis of density. Spirals are widely used in mineral processing as a method for preconcentration and have proven to be metallurgically efficient and cost effective.Spirals have a wide application, they are used in iron ore processing, coal, gold, chromites, mineral sands, glass sands, and in soil cleaning.Separation on a spiral is achieved through a combination of forces that act on particles as they move down the trough of the spiral. The main forces known to act on the particle on a spiral are the gravitational forces, centrifugal force, hydrodynamic drag, and lift and friction forces (Kapur & Meloy, 1998). Apart from the forces acting on a spiral, the properties of the slurry flowing on a spiral including, solids concentration, feed rate and wash water also plays an important role in the separation on the spiral.The relationship between separation efficiency and feed rate was shown to be linear, with a decrease in efficiency at higher flow rates. Previous work on flow profile by Holland - Batt (1990) indicated that any increase in the feed rate to a spiral results in a greater part of the additional flow volume reporting to the outside of the trough. The flow on the outside of the trough becomes energized and consequence to that the heavy particles find it hard to settle and escape this region to the inner region. This effect has a high impact on recovery of heavy minerals, since any increase in volumetric flow on the spiral is not made available for recovery in the inner region of the spiral."

Jan 1, 2015

By P. A. Mingione

"AEROPHINE@ 3418A is a unique sulfide mineral promoter produced by Cyanamid, based on phosphine (PH3) chemistry. It has proven effective as a collector for the sulfide minerals of copper and particularly lead (galena), as well as for secondary gold and silver values. AEROPHINE 3418A has widest application as a Cu and/or Pb collector for complex ores of Cu-Zn and Pb-Zn, which frequently have significant quantities of associated precious metal values. Advantages shown in the use of AEROPHINE 3418A are improved selectivities against Zn- and Fe-sulfides, increased precious metals recoveries, reduced total collector consumptions for Cu and/or Pb flotation, and increased flotation kinetics leading to higher recoveries of these values. Operating plant, pilot plant and laboratory test data from treating different ores are presented, demonstrating the advantages in use and preferred application of AEROPHINE 3418A.INTRODUCTIONCyanamid operates the only phosphine and phosphine derivatives plant in North America, located in Niagara Falls, Ontario. Specialty chemicals manufactured at this facility are used in many diverse applications, including solvent extraction reagents and textile flame retardants. A unique phosphine-based sulfide mineral promoter, AEROPHINE 3418A, is also produced. The origins of AEROPHINE 3418A promoter date back to the 1960's, when it was established that sulfide mineral collectors based on phosphine chemistry demonstrated efficacy. This new collector chemistry was found to provide flotation performance differing significantly from those of more traditional thiol collector chemistries such as xanthates, dithiophosphates, mercaptobenzothiazoles, thionocarbamates and those with xanthogen groups. Some of the advantages ultimately demonstrated by AEROPHINE 3418A promoter compared to these traditional collectors include:"

Jan 1, 1990

By Ben Murphy, Tomi Maksimainen, Antti Rinne, Ishmael Muzinda, Toni Mattsson

"A 500m3 flotation cell was commissioned during 2014 at the Kevitsa Mine in northern Finland working as the first rougher in the copper flotation circuit. Treating around 850tph with an average grade of 0.3% Cu, the TankCell® e500 has run with an average copper recovery of 71% and an average enrichment ratio of 50 during early optimization test work. In addition the cell has proved to be very energy efficient, being operating with a specific energy of around 0.4kW/m3 under production conditions.A review of the installation and operation of the TankCell® e500 at Kevitsa will be presented. Metallurgical performance of the cell during the operating period will be discussed on the basis of on-line analysis and the metallurgical samples collected during early optimization campaigns.IntroductionThe past three decades have seen a rapid increase in the size of mechanical flotation cells. This has been largely driven by demand from the copper industry to process larger volumes of material due to combination of declining head grades and the desire to benefit from the economies of scale (Lynch, Harbort and Nelson 2010). During this period Outotec has been at the forefront of development of large flotation technology with an enviable scale-up track record; 100m3 (1995), 160m3 (1997), 200m3 (2002), 300m3 (2007), 500m3 (2012) to the largest commercially available cell at 630m3 in 2013. This scale-up methodology has been developed, tested and validated (Elgueta et al., 2009; Coleman & Dixon, 2010) by the large installation base of cells in the 300m3 size class operating (over 400). The learning from large cell operation are then reviewed and incorporated back into new designs and scale-up practices (Murphy, Miettinen, and Yanez, 2014)."

Jan 1, 2016

Operations and maintenance departments have had a long-standing adversarial relationship. The widespread evolution and adoption of modern management techniques, such as reliability centered maintenance (RCM) and Lean, however, has driven interest in working co-operatively to optimize overall plant performance. Mining and minerals operations have long adopted RCM in maintenance and are now adopting Lean throughout organizations. Such modern management initiatives explicitly call for co-operation between the two disciplines of maintenance and production and many advances have been made in terms of people and methodology. One area that has lagged behind in supporting these developments, however, is information systems. Enterprise asset management (EAM) systems in maintenance and newer manufacturing execution systems (MES) in operations have not been truly integrated in the needed ways. Complicated plants, different software architectures, continually changing conditions and many other variables have led to systems problems, which have contributed to the maintenance/operations divide. Master data synchronization (the plant tree) and integrated reporting of real-time data with transactional data are just two of the issues that are being solved by new approaches in information technology, including web services and service orientated architectures. New technologies are coming on-stream to enable the final bridging of the gap.

Jan 1, 2009

By G. P. Holmes

"IntroductionThe copper-molybdenum property of Brenda Mines Ltd. is located 18 miles north west of Peachland in the Okanagan Valley of the Southern Central interior of British Columbia. The actual site is 50 miles north of the international boundary and 150 air miles east of Vancouver at an elevation of 5000 feet above sea level. The earliest written mention of the prospect is found in the Geological Survey of Canada, Memoir No. 243, issued in 1947 by Dr. H.M.A. Rice. In 1954 the area was staked by a prospector, Bob Bechtel, who interested Bern Brynelsen of Noranda Exploration in examining the claims. A joint Noranda - Kennecott program resulted but since the grades were so low the property was not taken up until in 1964 a re-examination by Chapman, Wood and Griswold produced recommendations leading to the construction of the Brenda Mine as it is today.The rounded, timber covered mountains of the area are composed of the tuffs, argillites and limestones of the Upper Triassic Nicola Group, which is intruded by a Jurassic quartz diorite, called the Brenda stock0 The actual orebody occurs in a strongly fractured zone within the Brenda stock, approximately 1500 feet from the contact with the Nicola group0 The ore minerals, .chalcopyrite and molybdenite, associated with pyrite and magnetite of lesser importance, occur as fillings within the fractures 0 The grade of the ore decreases outwards from a central higher grade core and in January 1971 total reserves were estimated at 165 million tons assaying 0,182% Copper and 0,049% Mo."

Jan 1, 1972

By Zachary Mayer

Agenda ? Kidd Mine ? Background ? Problem & Opportunity ? Challenges associated to depth - Production Rates - Productive Work Time - Operational Delays - Transfer Levels - Mucking Time - Impact on Hoist ? LHD Automation ? Sandvik AutoMine Lite ? Expected Benefits Kidd Mine - Background ? Located in Northern Ontario, Canada ? Underground base metal mine operating since 1966 ? Total 148 Mt mined (2.31% Cu, 6.08% Zn, 75 gpt Ag) ? 2.35 Mt/Y from stopes as deep as 9500 ft (2.9km) below surface ? Mining method: blasthole open stoping ? Mine/Mill: 1263 employees and contractors ? 2012 National John T. Ryan Safety Award

Aug 1, 2013

By G. Naud, J. Robitaille, M. Buonvino, A. Veltmeyer, A. R. Laplante

"A B6 Falcon concentrator was tested on several systems: a synthetic magnetite-silica ore, a massive sulphide gold-copper ore, a fine gold-pyrite-silica flotation tail, and a high grade gold ore in a low sulphide gangue (cyclone overflow).The Falcon demonstrated its ability to achieve separation in all cases, but with varying degrees of success. For the magnetite-silica system, separation proceeds until the concentrate bed overloads, at a mass of 300 to 400 g of magnetite. Recovery increased with decreasing particle size, down to the 25-37 µm and in some cases even the -25 µm class. Bowl geometry (angle) and gangue size distribution were the most significant operating variables. Results with the massive sulphide ore were the poorest, with gold recoveries typically around 10 to 20% at very low upgrading ratios, 1: 1 to 5: I. Gold recovery from the fine flotation tail ranged from 30 to 70% at upgrading ratios of 5 to 15; actual plant application would require a continuous unit (Falcon C20). The high grade gold cyclone overflow yielded a wide range of gold recoveries, but a very consistent relationship between recovery and mass processed. A concentrate of 0.5% Au could be processed at a recovery of 50%.The paper also presents results of a C20 application to recover fine iron from a magnetic tail. The unit is capable of recovering approximately 70% of the fine liberated iron in a high density product, with modest upgrading below 105 µm, and virtually complete rejection of the + 300 µ m product."

Jan 1, 1993

By Xing Jin, Dan Graffi, Glenn MacPherson, Dan Rioux

"The complexity of a modern flotation circuit makes it susceptible to disturbances such as changes in feed, ore mineralogy, equipment degradation, poor measurements and faulty instruments. Good measurements and a robust control system are critical to create and maintain a stable and optimum flotation process.This paper focuses on the development and implementation of process control applications in the flotation circuits at Xstrata Nickel’s Strathcona Mill ( referred to as the mill hereafter ) in Sudbury, Ontario. Following the path of ‘stabilize-improve-optimize’, basic controls to stabilize process variables such as flotation cell pulp level, air and reagent addition rates, cleaning-column feed and wash-water rates have been established. Factors such as best practice in pulp level and valve position measurement, feedforward control and the application of an appropriate control philosophy, have contributed to the significant reduction in process variability. For instance, standard deviation reduction of 79% for the Ni impurity in the column Cu concentrate grade was experienced and is shown. The variability reduction of the flotation circuits’ key process-variables paves the way to further improve and optimize flotation performance. A grams-per-metal unit reagent addition control scheme has been improved upon, particularly for different operating scenarios and better robustness. In addition, following significant stabilization of the primary controls and columns feedrates, Cu/Ni separation cleaning-column bias-control (cascaded to the wash-water rate) and hold-up control (cascaded to air flowrate) have been developed and tested. This strategy – from stabilization to optimization - is expected to achieve a more consistent control of final concentrate grades and improve recoveries.INTRODUCTIONFlotation is considered the most important and value-added process in the milling metallurgical plant and is still undergoing continuous evolution to treat greater tonnage and different ores (Wills, 2006). Starting over three decades ago, with the advent of on-line slurry content analysis devices, flotation automatic control has received persistent interest and a large number of applications have been reported (Thwaites, 1983, 1986 ; Mckee, 1991). Bergh and Yianatos (2011) reviewed different aspects of process control in flotation circuits and have evaluated the applicability of model predictive control to the process. Mckee (1991) analyzed the difficulty in developing lasting/robust process control applications for flotation circuits and stated that the path of stabilization-refinement-optimization would more likely lead to successful flotation circuit process control. Best practice on column process control was discussed by Bouchard, etc. where a multi-layered approach was proposed, provided that the measurement of column process variables ( i.e. bias, froth depth, hold-up, etc. ) are measured reliably (Bouchard & Thwaites, 2008). Wills (2006) stated that the best practice for flotation automatic control starts with fulfilling basic control objectives, such as stabilized flotation cell level, air flow, pH, reagent flow etc., before considering more advanced, or even optimal, control of metallurgical targets, which are more closely linked to economic performance."

Jan 1, 2013