Search Documents

By C. Vipulanandan

Installation procedure and the quality of the material used in the construction have significant effects on the behavior of the Auger Cast in Place (ACIP) piles. In this study, Installation and curing of a 760 mm (30 in.) diameter and 12 m (39 ft) long ACIP pile with a design capacity of 1140 kN (128 tons) in hard clay was investigated. Construction quality was monitored using the automated monitoring system where the volume of grout pumped and the pressures were monitored with depth. The curing of the pile was monitored using axial vibrating wire strain gages at four levels and lateral vibrating wire strain gages at two levels. The residual strain and temperature profile in the curing pile was monitored over a period of week to determine the appropriate time for load testing the pile. Axial behavior of Auger Cast in Place (ACIP) Piles in hard clay was studied using full scale load test on an instrumented pile. The load-settlement and load transfer relationships of the pile was investigated based on the load test results. Development of skin friction in the load test pile and the reaction pile was also investigated.

By Saieb Haddad, Henry Pate

"Building retaining walls in an urban area is becoming more difficult due to right-of-way restraints. Using standard concrete cantilever walls requires a construction easement behind the walls for installation, which for the most part is unavailable. To install these types of walls in a limited right-of-way requires extensive temporary walls to minimize the construction easement. Top-down construction walls utilizingtie-back anchors for support require either the purchase of the right-of-way or underground easements in the area of the anchors.These problems faced the Department on Interstate 75 widening in Knoxville, TN in an area of a large cut. A multi-story Insurance Building and a large commercial Retail Center were located at the top of the cut. To prevent any impact on the buildings, the walls had to be placed within a limited area. The option of buying the properties was prohibitively expensive. Due to the height of the two walls and the variability of the underling rock line, contiguous caisson pile cantilever walls were contemplated as the only wall type that would be appropriate. The cost of the two walls was estimated to be very close or even higher than the cost of purchasing the two buildings. The Department believed that there must be a better way to deal with the problem. A vertically tied-down pile frame wall constructed from the top-down with a concrete facing was developed. This allowed the construction of the walls to be restricted to the available limited area and provided substantial savings for the State.INTRODUCTIONThe widening of I-40/75 has been a major transportation project in the Knoxville area which is being constructed by the Tennessee Department of Transportation. The project includes 18 Retaining Walls and 13 Bridges.Two of the 18 Retaining Walls, refer to Figure 1, are to support two valuable properties, one being an insurance company housed in a multi-story office building and the other a suburban shopping center which were appraised at $13.0 million and $5.0 million respectively. Due to the 31 ft. (9.5m) maximum height of each of the two Retaining Walls and the limited Right-of- Way of 15.0 feet (4.6m), a contiguous caisson pile cantilever wall was proposed for each of the two retaining wall sites with an estimated cost of $12.0 million each. The contiguous pile cantilever Wall is comprised of a line of caisson piles socketed into underlying competent bedrock. The design required that 4 ft. (1219mm) dia. piles be installed at 6 ft. (1.83m) centers, socketed into rock in order to provide lateral stability and restrict lateral wall movement to acceptable limits. The line of caissons would be fronted with a cast-in-place concrete face wall"

Jan 1, 2007

By Tracy Brettmann, Shailendra Endley, Jason Leary, Shashank Valluru

"Augered Cast-in-Place (ACIP) piles have long been used for deep foundation support in sands due to their high capacity and speed of installation. Very little information exists on the effects on capacity if the auger needs to be withdrawn from the hole prior to grouting. This condition can occur due to various reasons including grout plug ups, equipment issues, and grout supply delivery problems. It can become a major problem for the project team if this happens during production because the capacity of that pile is then in question, potentially resulting in re-design, installation of replacement piles and/or schedule delays. This paper compares the results of two high capacity test piles installed into a dense sand where one test pile was installed by first completely withdrawing the auger from the hole after drilling to the pile tip depth and the other test pile was installed utilizing conventional industry standard methods. Identical load tests were then performed on both piles to compare the effects of the two different installation procedures. The load test results were surprisingly similar in this case although the grout take required for the test pile installed in the pre-drilled hole was significantly higher to produce a similar grout return depth.IntroductionAugered Cast-in-Place (ACIP) piles are used extensively along the Texas Gulf Coast due to their combination of high capacity and speed of installation resulting in one of the most cost effective deep foundation systems relative to other options. Soil conditions in this region typically consist of alternating layers of sand and clay in the upper several hundred feet. ACIP piles are routinely installed to depths of over 100-ft to achieve the required capacity depending on the site specific soil conditions and therefore typically extend through and tip into sand layers. Occasionally, due to various reasons like equipment issues and plug-ups, the auger is withdrawn from the hole without grouting. Significant sand in the soil profile could lead to questions about the effect of the auger withdrawal on the pile capacity and load deflection relationship.This paper summarizes the results of two identical pile load tests performed on adjacent piles of the same length with the main difference being one was installed using the standard installation procedure and the other was installed by first completely withdrawing the auger from the hole after drilling to the pile tip depth. The load test results were then evaluated using load transfer analyses to estimate the effect of the withdrawal of the auger on the load-deflection characteristics and capacity."

Jan 1, 2017

By Aly Mohammad, Dongyi Yue

"The design of rock sockets for drilled shafts and piles proves to be a challenge for the Design Engineer. The magnitude of loads on the shaft and the behavior of the rock are critical in determining the required socket length. Several acceptable methods are available in the literature to analyze a rock socket under a combination of axial loads, lateral loads and moments. This paper will present a state-of-the-art methodology to analyze rock sockets utilizing deformation characteristics of the rock. This design methodology was implemented in the design of a major project in New York City.The project discussed herein is a marine transfer station planned for construction at East 91st Street along the East River in Manhattan. In order to support the piers and platform structures at a site with relatively shallow depth of the bedrock, rock sockets were required for the drilled shaft foundations. Rock sockets were utilized to provide the required fixity to the foundations and the structures. Acting at the top of the rock sockets are large shear forces and moments created by the lateral loads transferred from the structure.Upon review of the available techniques, a simplified method was proposed and used to analyze the rock sockets with a significant magnitude of lateral loading. The method recognizes two mechanisms through which the lateral shear and moment are transferred to the rock; a) load transfer through horizontal resistance of rock and b) the vertical shear resistance of the bond between socket and rock.The first load transfer mechanism was analyzed using the p-y curve method based on a rock model developed by Reese. The second was analyzed using a bond stiffness derived from the formula and curves utilized in the AASHTO Specifications for calculation of rock socket displacement. By comparing the two mechanisms, the main contribution to the large horizontal shear force that developed in the rock socket is identified.The paper will present a summary of the design methodology utilized in determining the length of the rock socket. It is believed that the presented method will provide substantial cost saving in selecting the most economical and efficient design length."

Jan 1, 2005

By Saieb Haddad, Henry Pate

"Building retaining walls in an urban area is becoming more diffi cult due to right-of-way restraints. Using standard concrete cantilever walls requires a construction easement behind the walls for installation, which for the most part is unavailable. To install these types of walls in a limited right-of-way requires extensive temporary walls to minimize the construction easement. Top-down construction walls utilizing tie-back anchors for support require either the purchase of the right-of-way or underground easements in the area of the anchors.These problems faced the Department on Interstate 75 widening in Knoxville, TN in an area of a large cut. A multi-story Insurance Building and a large commercial Retail Center were located at the top of the cut. To prevent any impact on the buildings, the walls had to be placed within a limited area. The option of buying the properties was prohibitively expensive. Due to the height of the two walls and the variability of the underling rock line, contiguous caisson pile cantilever walls were contemplated as the only wall type that would be appropriate. The cost of the two walls was estimated to be very close or even higher than the cost of purchasing the two buildings. The Department believed that there must be a better way to deal with the problem. A vertically tied-down pile frame wall constructed from the top-down with a concrete facing was developed. This allowed the construction of the walls to be restricted to the available limited area and provided substantial savings for the State. INTRODUCTIONThe widening of I-40/75 has been a major transportation project in the Knoxville area which is being constructed by the Tennessee Department of Transportation. The project includes 18 Retaining Walls and 13 Bridges. Two of the 18 Retaining Walls, refer to Figure 1, are to support two valuable properties, one being an insurance company housed in a multi-story offi ce building and the other a suburban shopping center which were appraised at $13.0 million and $5.0 million respectively. Due to the 31 ft. (9.5m) maximum height of each of the two Retaining Walls and the limited Right-of- Way of 15.0 feet (4.6m), a contiguous caisson pile cantilever wall was proposed for each of the two retaining wall sites with an estimated cost of $12.0 million each. The contiguous pile cantilever Wall is comprised of a line of caisson piles socketed into underlying competent bedrock. The design required that 4 ft. (1219mm) dia. piles be installed at 6 ft. (1.83m) centers, socketed into rock in order to provide lateral stability and restrict lateral wall movement to acceptable limits. The line of caissons would be fronted with a cast-in-place concrete face wall."

Jan 1, 2007

By Kazuyoshi Kamimura, Masaya Kawata

"It has been 30 years since the cement deep mixing (CDM) method developed in Japan. CDM method has been applied to many structures. While various technical improvements have been implemented in the meantime, the single-axial and double-axial technologies used at the time of its initial development are still prevalent.In response to the recent trend of reducing construction costs, we developed a triple-axial CDM method called the “Lemni 2/3 Method.” This method uses two lemniscate motions caused by newly developed auxiliary stirring devices and employs a double-axial injection method in which the cement slurry injection takes place only from the outer two axes. In this way, it is possible to create a stabilized body around the three axes. Moreover, this method does not require substantial equipment investment as conventional construction machine and facilities can be used without modification and large volume work is possible.With these technologies, this method can achieve a substantial reduction in the construction period and cost, while ensuring the same level of improvement quality as conventional methods. As a result, this method is being applied to ground improvement work in a variety of places.Lemni 2/3 Method was first put to practical use in 2004. Since then, the method has been used for ten projects. In this paper, we show some application examples of this method.OUTLINE OF TRIPLE-AXIAL CDM METHOD (LEMNI 2/3 METHOD)In the newly developed CDM method (Lemni 2/3 Method), work efficiency is improved by employing triple-axial stirring blades instead of the conventional single- or double-axial type. Existing conventional construction facilities for double-axial type can be used with only minor equipment additions, because the cement slurry injection takes place only from the outer two axes.Construction Machine and Construction MethodThe combination of major construction machines of the Lemni 2/3 Method differs little from the standard specifications of the double-axial type as shown in Fig. 1. Existing work control equipment can be used without modification, which is further evidence of the simplicity, convenience, and economy of the new method. The Fig. 2 photo shows a full view of the construction machine, and the Fig. 3 photo shows the stirring blades and the auxiliary stirring devices. The work procedure for the Lemni 2/3 Method is shown in Fig. 4."

Jan 1, 2015

By Rob van Dorp

"AbstractThe Monitoring & Instrumentation Committee (MIC) of DFI Europe has the objective to support DFI members in concern of risk management of geotechnical matters, where monitoring and instrumentation have added value.Work of the CommitteeA study by the committee showed that there are already several existing (national) guidelines. They all have their strengths and limitations and their focus may vary a little per country due to local regulations and typical local building activities, but the main question remains what added value another new guideline would have. More likely it would add to the confusion instead of providing overview.Companies with larger experience in geotechnical monitoring (often larger consultancy firm, contractors or clients) are already quite familiar with its benefits do not really need a new guideline in how to design and effectively apply sophisticated geotechnical monitoring systems for special projects.Therefore the aim of the MIC is to focus a little more towards smaller organizations - that are less familiar with monitoring and instrumentation - and the more ‘regular’ type of project that they are mainly involved in. The MIC wants to create a tool which helps them to create risk awareness, to understand the benefits of geotechnical monitoring and to provide them information about how and where to find the right partners and equipment to setup and apply appropriate monitoring systems for their projects.Monitoring and instrumentation benefits are for example:• Risk control during construction stage;• Costs reduction in design and construction (taken limitation of geotechnical aspects into account).• Prevent of unnecessary delays in construction work• Increasing general awareness of geotechnical risks and possibilities of monitoring.The cost of monitoring compared to the cost of failure and/or the savings that can be achieved play a role in the work of the committee. DFI members benefit from the shared knowledge by the MIC on monitoring and instrumentation within their process of risk management."

Jan 1, 2014

By Dongwook Kim

Recently, load and resistance factor design (LRFD) is gradually being adopted internationally in geotechnical design due to the advantages of LRFD over the existing allowable stress design (ASD). LRFD is a more advanced design method compared to the ASD because resistance factor is calibrated based on the reliability analysis for a given target reliability index. Target reliability index changes with the importance of the structure. Typically, target reliability index of offshore foundation is less than those of onshore. The widely-used Imperial College Pile (ICP) design method is used for the calculation of pullout capacity of driven piles. The uncertainties regarding pullout capacities of driven piles are assessed using the statistical data reported in the literature. The first-order reliability method (FORM) is used to calibrate resistance factors for the pullout ultimate limit states of the driven piles for three different levels (2.5, 3.0, and 3.5) of target reliability index. The load factors used in this paper are the ones proposed in the AASHTO LRFD bridge design specifications.

Jan 1, 2010

By Alessandro Bertero, Stefano Valagussa, Filippo Maria, Wesley Schmutzler, Leoni

"Abstract The Deep Mixing Method (DMM) represents a viable solution to improve the adverse geotechnical properties of foundation soils. Differences and the importance of performing pre-construction laboratory and field tests will be highlighted. Comparative analyses and interpretations between the various lab and field stages, along with accumulated information about soil properties and QC results, allowed fine-tuning of the production parameters throughout almost the entire project.Two projects where the US Army Corps of Engineers selected the Deep Mixing Method (DMM) for the required stabilizations, and a third project completed in Italy, will be illustrated:•,?the LPV 111 Project (New Orleans - LA – USA); DMM was used for groundimprovement/foundation strengthening and consequently stabilize and support the burden of the new levee.•,the Rio Puerto Nuevo Project (San Juan - PR - USA); DMM was applied to improve the soils adjacent to a 90” forced sewer main relocation and to improve the soils for the base of a new drainage channel•,the new Italian high speed railway project (Florence Italy); DMM technology was applied to realize a a TBM break in/break out, foreseen originally by jet-grouting.IntroductionThe Deep Mixing Method (DMM) represents a viable solution to improve the adverse geotechnical properties of foundation soils. The effectiveness of working parameters depends largely on the physical and mechanical properties of the soil to be treated. Therefore, well designed laboratory and field test programs, aimed to disclose the interaction between the site-specific soils and the mixing parameters, are essential to achieve the desired end product."

Jan 1, 2014

By Charbel Khoury, Kwabena Ofori-Awuah, Kofi B. Acheampong

"Following heavy rains in spring of 2014, Prince George’s County officials issued a mandatory evacuation for homes in the Piscataway Hills subdivision of Fort Washington, Maryland where a landslide along a 1700-foot hillside destabilized homes, collapsed the single access road, and resulted in water and sewer mains break. Forensic investigations, including geologic assessments, test borings and in-situ Cone Penetrometer and Dilatometer soundings, were performed to evaluate subsurface conditions and provide stabilization options for the roadway and slopes. Post-failure ground movements were monitored using inclinometers. Critical failure planes were identified within the underlying 30-foot thick Marlboro Clay formation, a known geologic hazard with historic occurrences of landslides and slope failures.This paper discusses the remedial design for stabilizing the landslide and 60-foot hillside slope failure, and protecting the roadway. Amongst several feasible options, driven piles were selected in consultation with the County and retained contractor based on cost, environmental impacts and site constraints. Constraints included private ownership of hillside slope, upslope buildings safety; deep-seated failure, relocation of underground water and sewer mains, and accelerated construction schedule.Pile design included global slope stability analyses and lateral pile analyses using several loading configurations to optimize pile geometry and spacing, and determine a value-engineered design satisfying both serviceability and strength limit states to achieve long-term stability with factor of safety of 1.3. Soils within the active landslide plane were assumed to provide no resistance, while soils below the failure plane provided lateral resistance. This stabilization scheme, which extended along the 1700-foot roadway section and toe of hillside slope area, consisted of 410 steel HP16x141 piles in two to three rows driven to depths between 60 and 70 feet below the Marlboro Clay stratum at 5 to 7-foot spacing."

Jan 1, 2017

By Michael Perlow Jr

A modification of the original Davisson Offset Limit (DOL) is presented for drilled foundations using soil quake (QDOL) factors ranging from 2 to 6. A further modification of the Davisson Offset Limit has also been developed using helical pile soil quake values (HDOL) based upon helix diameter. In addition, the initial tangent slope (IS) of the pile load test displacement curve is used in lieu of the calculated elastic slope (ES) to eliminate many of the uncertainties associated with determining the drilled foundation pile elastic modulus. The QDOL and HDOL load test methods do not require any graphical interpolation and provide easy simple ultimate pile capacity interpretation methods where drilled foundation pile load tests are not carried to plunging failure. Drilled foundation and helical pile load test case studies are presented to demonstrate the use of the modified soil quake QDOL and HDOL Methods.

By Martin B. Hudson, Andrew K. Cho, Rolff B. Knobel, Les R. Chernauskas, Jonathan L. Ernst

ABSTRACT The Bruce Museum, located in Greenwich, Connecticut, is home to an extensive display of art and natural history exhibitions. A large addition was designed to be constructed adjacent to the museum requiring new spread footings to be installed up to 16.5 feet below the existing foundations. The soil conditions at the site consist of highly variable sand and gravel overlying weathered rock and sound bedrock. The Contract Documents called for traditional foundation underpinning. Traditional underpinning techniques, however, presented two major challenges on this Project; (1) deep underpinning pits would be required involving multiple levels and staging with tieback support and (2) the highly variable soil and bedrock composition and elevations presented uncertainty in the design and construction of the pits. In lieu of traditional underpinning, Geosciences Testing and Research, Inc. (GTR) proposed an “active” soil nail underpinning system. A major reason that the soil nail underpinning option was feasible, related to the fact that the soil nails and facing could be installed slightly in front of the existing footings rather than directly underneath the existing footings. The soil nail wall design involved one to four rows of soil nails with nail positions and wall depth able to be adjusted “on the fly” as excavation progressed depending on the field conditions encountered. To create the “active system,” the soil nails were pre-loaded to mitigate wall deformations that would be associated with a standard passive soil nail wall design. To evaluate the performance of the active soil nail wall and confirm design assumptions, an extensive automated monitoring, on-site testing and inspection program was proposed and executed by GTR to monitor deformations of the wall and the museum in real-time, evaluate and confirm bedrock and soil bond stresses and ensure that each soil nail was pre-loaded and locked off. Careful analysis, planning, and use of the observational method illustrates the importance of collaboration between design and construction personnel and applying engineering judgement throughout construction. The use of the observational method includes the potential for modifying design based on conditions observed. This paper presents a unique case study of the “active” soil nail underpinning system to support and protect sensitive structures, close collaboration between design and construction facilitated by real-time deformation monitoring, and its successful application as a safe and cost-effective alternative to traditional underpinning.

Oct 1, 2022

By Adam Zagorski, Rusty Lucido, Curt Scheyhing

"The current California Department of Transportation (Caltrans) practice based on AASHTO LRFD Bridge Design Specifications is to use the O’Neill and Reese method (FHWA, 1999) for calculating the side resistance and base resistance of Cast-in-Drilled-Hole (CIDH) piles / drilled shafts. In this calculation, end bearing is typically neglected for piles constructed using a wet method due to questionable reliability of end bearing resulting from soil disturbance and inadequate cleaning of the base. Pressure grouting below the tips of drilled shafts in cohesionless soils has long been used worldwide to provide reliable end bearing capacity, but for decades it was relatively unused in this country. It has been used increasingly in the United States over the last decade. Before this project tip grouting has not been utilized on or accepted by Caltrans to maximize piles end bearing capacity. This project proved that tip grouting to mobilize reliable base resistance can be successfully implemented on a full-scale bridge project requiring over 350 large diameter shafts.For the Gerald Desmond Bridge Replacement Project, Shimmick/FCC/Impregilo, JV utilized a temporary Oscillator casing to the full depth to install CIDH piles. Piles were constructed by the wet method and then pressure grouted below the pile tip. A tip grouting procedure for these large diameter shafts was developed and tested to specifically address the geology and constraints of the project. This procedure was then proven during the Load Testing of test piles during the Test Shaft construction phase of the project. Tests showed a minimum reliable base resistance of 150 ksf could be mobilized in very dense sand at a downward movement of 5% of the pile diameter for piles ranging from 4.9 to 8.2 feet in diameter. By tip grouting, the length and diameter of the piles were significantly reduced."

Jan 1, 2017

By John P. Turner, Benjamin J. Turner

"Non-destructive testing and evaluation (NDT/NDE) methods have become standard tools as part of the post-construction quality assurance of drilled shaft foundations. In responding to anomalies, foundation designers, owners, and contractors face a number of choices, including: (i) acceptance of a shaft with known anomalies, (ii) further investigations of integrity (e.g., concrete coring), (iii) repair schemes, and (iv) reject and replace. To assist in selecting the best option, analyses are often performed that involve assessing the structural performance of reinforced concrete shafts that may include defective concrete or voids. Currently, the analytical tools for predicting the flexural strength and stiffness of drilled shafts with defective concrete located in discrete regions of the cross section are limited. This paper presents a robust moment-curvature analysis tool for drilled shafts based on the fiber-element discretization method. The tool allows for consideration of anomalous or defective concrete regions in the shape and location that they are believed to exist in the shaft while considering explicitly the nonlinear material behavior of the intact regions based on expected material properties. A case study is used to illustrate the practical application of the analysis to drilled shaft projects.INTRODUCTIONImperfections such as defective concrete or accidental eccentricity of reinforcing cages are an inherent part of the drilled shaft construction process that will occur occasionally even when construction best-practices are followed. Petek et al. (2002), O’Neill and Sarhan (2004), Poulos (2005), and others have described the effects that construction defects can have on the axial and lateral performance of drilled shafts. Our industry has seen rapid progress in recent years in the development and improvement of tools for detecting drilled shaft anomalies, such as gamma-gamma and crosshole-sonic logging, sonic-echo testing, thermal integrity profiling, and even visual inspection with invasive video cameras. Nonetheless, in most cases the wealth of data from these tests is used by foundation engineers to make a fairly “black or white” decision—should the defects be repaired, or should the shaft be rejected? A third option that is not typically considered is to directly analyze the section, including anomalies, and compare the reduced strength and/or ductility to the actual project demands. This option takes full advantage of the data collected during integrity testing, and may provide a justifiable means for avoiding further construction costs and delays, whether for repair or replacement."

Jan 1, 2016

By Abolfazl Eslami, Fatemeh Valikhah

"Complexity in soil-foundation interaction and subsoil nonlinear behavior cause difficulties and uncertainties in evaluating the actual values of foundation design factors such as settlement. The acquired continuous records of Cone Penetration Test (CPT) can be used to determine the soil profile and characteristics those are applicable in the geotechnical design. In this paper, it has been attempted to present a new non-linear stress-strain approach to estimate the foundations settlement by using CPT data in the form of soil behavior classification charts. This new approach is based on Janbu method (1960s and also 1998). Instead of using fixed and constant values for stress exponent (j) and modulus number (m), continuous coefficient variations can be used. The proposed approach also can be used as a new method to predict pile group settlement. A data bank has been compiled containing twenty-two practical case histories to investigate the accuracy of the predictions made by the proposed and available common methods. The comparisons indicate that the proposed approach is relatively able to predict the settlement close to their real values. Therefore, it can be considered as an alternative method based on valuable CPT data and nonlinear stress-strain approach for foundations and pile groups settlement estimation.INTRODUCTIONComplexity in soil behaviour for settlement analysis is the result of non-linear and time dependent stressstrain behaviour of soils, their elasto-plastic performance under loading and unloading situation and also effects of stress history (Holtz et al., 2011; Fellenius, 2015). Hence, many relations and equations have been proposed to predict foundation settlement, where most of them are based on typical different parameters such as soil stiffness (E), foundation width (B), contact pressure (q) and pressure developing in depth (Janbu, 1967 also 1998; Briaud and Gibbens, 1999; Uzielli and Mayne, 2012).The Janbu approach for settlement estimation, proposed by Janbu in the early 1960s, combines the basic principles of linear and non-linear stress-strain behaviour of material. The method is applied to all types of soils. The relation between stress and strain is a function of two non-dimensional parameters which are unique for any soil: a stress exponent, “j”, and a modulus number, “m”. The Janbu relations are derived from the definition of tangent modulus by the following expression:"

Jan 1, 2017

By Roger A. Bullivant

The introduction of this size and type of piling rig is intended to address a multipurpose foundation activity. The 8000 denotes the size of equipment that is attached to the mast, namely 8000 Kg. Larger equipment can be carried subject to adjustment of rig geometry. The 8000 series rig will easily accept hydraulic piling hammers and CFA equipment, but for the purpose of this discussion it will be equipped with an auxiliary power pack that is matched to twin vibrators. The design of the siamesed vibrators allows long tube equipment or piles to be driven with a short mast configuration that provides a lower overturning risk. It is easily adapted within minutes to carry out other foundation requirements that are required on the same contract. The piling and ground consolidation activities that can be undertaken by the 800 series machine are:-

Jan 1, 1995

By C. Vipulanandan

With the aging infrastructure, there is a need to maintain and extend the service life of steel structures in general and steel piles in particular. Steel piles support not only vertical loads but also dynamic horizontal loads in onshore and offshore applications. In order to select the appropriate methods to repair corroded steel piles used in onshore and offshore application, corrosion mechanisms were investigated with the rate of corrosion in various environments. The corrosion rate of steel in soil, water and soil-water interface varied from 2 to 500 µm/year. Based on literature review and analyses, the repair methods can be broadly characterized as protective coating, electro-chemical methods, wrapping and encasement and partial replacement of steel. Also, methods to evaluate the repair materials and the repair configuration have been documented.

By Thomas Billups, Brendan FitzPatrick, Doug LeDo, David Carchedi

"Working in urban environments presents unique logistical challenges beyond those typically associated with traditional geotechnical analysis and design. These challenges often include working on sites with limited access and laydown area, vibration concerns for adjacent structures and the need to work from variable elevations or within excavations. This paper describes the use of the modular Ductile Iron Pile system, a low-vibration driven micropile, on two urban projects on the Johnson & Wales University campus in Providence, Rhode Island. The paper describes the successful implementation of Ductile Iron Piles installed to develop capacity in end-bearing on one site and friction on the second site. Design, installation and quality control operations are all presented as well as the results of full-scale load testing performed on non-production test piles. This paper is of importance to the industry because it describes a versatile option for project teams as an alternative to traditional micropiles, helical piles or other deep foundation systems for urban sites.INTRODUCTIONWorking in urban environments presents unique logistical challenges beyond those typically associated with traditional geotechnical analysis and design. These challenges often include working on sites with limited access and laydown area, vibration concerns for adjacent structures and the need to work from variable elevations or within excavations. Two recent projects in downtown Providence, Rhode Island faced a combination of problematic soil conditions and urban construction challenges including vibration concerns. Both projects were a part of the Johnson and Wales University campus development. Figure 1 illustrates the urban locations of the sites."

Jan 1, 2016

By Vijaya Bhushan Rao, Jason Redgers

A mixed-use development comprising of multistoried residential towers, retail and associated infrastructure covering an area of 500,000 m2 is under construction in Dubai. The subsoil conditions consist of calcareous sands with high carbonate and shell content with hard and competent strata encountered at varying depths. To achieve the design requirements of soil stiffness, friction angle, limit differential and total settlements and mitigate the liquefaction due to a seismic event then ground improvement were deemed necessary. In order to provide the most time and cost efficient solution numerous techniques were applied to meet the requirements for all depths such as Vibrocompaction, VC (depth >8m), Dynamic Compaction, DC (depth < 8m)] and Rapid Impact Compaction, RIC (depth <4m). The specified ground improvement requirements were translated into a target Cone Penetration Test, CPT line that served as the defacto performance requirements for the project. Suitable correction factors were applied to the CPT results to account for the high carbonate content following the works of Al-Homoud and Wehr 2006, Belotti and Jamiolkowski , 1991 and Vesic, 1965. Furthermore, the alpha factor, α, used to obtain stiffness from CPT results was applied following A.C. Meigh 1987 and Massarsch & Fellenius, 2005 where high over consolidation ratios (OCR) could be demonstrated.

Sep 8, 2021

By Helen D. Robinson

Traditional practice to resist large lateral loads on foundations is the use of large diameter caissons, battered driven piles, or battered micropiles. Dense urban construction environments, however, limit the usefulness of these systems due to the close proximity of below- and above-grade obstructions. This paper presents two micropile construction projects in the United States where a complex scheme of battered micropiles and grade beams was developed to counteract large lateral loads at the foundation level. The paper also presents a procedure used to design vertical micropiles for large lateral loads, which can greatly simplify the design of foundations subject to significant lateral loads in urban environments. A design example shows a case where vertical micropiles were used to support allowable design lateral loads greater than 80 kip per micropile.

Jan 1, 2010