Search Documents

By Xuejing Xie, Tianxiang Ren

Paper presented at the 28th International Geological Congress held in Washington DC, July 1989 (International geochemical mapping sessions). Standardised stream-sediment sampling procedures have been used in mountainous and hilly terrains. Special sampling procedures were developed for application in remote environments, such as high mountains, desert, semi-desert, karst and loess-covered regions. The diversified analytical methods used in more than 20 analytical laboratories participating in the project have been unified into two multi-element, multi-method analytical systems. A unified data monitoring procedure was developed based on primary and secondary standard samples. To date the project has covered about 4 000 000 km2 and the aim is to complete the coverage within the present decade

May 1, 1991

By G. Kill

Although other energy commodities have developed successful futures contracts, long-term contracts still dominate the coal market. To establish whether coal markets will develop in the same way, coal price and volume data are tested against a set of criteria considered to represent some of the factors contributing to the development of a successful futures contract. Coal meets only some of the criteria: market players are subject to little risk in quite a stable market, have strong preferences for the specific nature of long-term contracts and profit from product uniqueness, each trade being individually negotiated. Potential structural changes in the western European market are not felt to be sufficient to create demand for a coal futures contract, but an empirical model has been developed that could form the basis of a further study to predict the potential for success

Aug 1, 1994

By Briggs H.

The illustrated device uses the principle that the lamp can burn with a smaller inlet passage if the air is rich in O2 and that the size of the inlet can be made a measure of O2 percentage. The appliance consists of an adjustable cut-off applied to the inlet of a safety lamp of the improved Gray pattern. Precision is assessed from tables of calibration tests in air contaminated with blackdamp of CO2:N2 composiiton 1:5.67 at temperatures of 40-70 degrees F. Results are presented of tests at St. Germain's colliery, of tests in air contaminated with pure CO2 and of air contaminated with both blackdamp and inflammable gas; published ranges in mine-air blackdamp compositions are tabulated as ranging from 90.06% N2 to 43.90% CO2. When firedamp is present at 1.25-2.5%, its content must first be estimated by means of the cap and a fifth of its value then deducted from the lamp reading for O2

Dec 1, 1916

By S Durucan, A Korre

The application of simple methods of statistical analysis, coupled with geostatistical analysis and geographic information systems, can only summarise and give an outline of the spatial distribution of the parameters measured. Spatial analysis of the components or factors calculated, through principal component analysis or factor analysis, allows assessment of the geographical distribution of the dominant processes contributing to soil composition and/or contamination. Neither of these tools, however, distinguishes between the different sources of pollution. The application of canonical correlation to the data, driven by expert appraisal of the potential pollution sources, allows their quantitative and spatial assessment while GIS provides the environment in which to organise and present the results. The methodology is illustrated by its application to soil-contamination data from the Lavrio area in Greece, where silver-bearing orebodies have been mined for more than 25 centuries

Jun 21, 1905

By G. X. Wang, R. E. Siemens, M. C. Fuerstenau, D. Chandra

Soda roasting of concentrates from Mouat, Montana, was performed in a temperature range of 450 to 650 degrees C and chromium was solubilised by water leaching at room temperature. It was found that high extraction yields of chromium were primarily dependent on the conversion of Cr3+ to Cr6+ during the roasting step, and this was enhanced significantly by simple attrition of chromite particles during this step. Gangue impurities (mainly Si) were more detrimental to Cr extraction than lattice impurities such as Al or Mg. It appears that oxidation proceeds into grains along a preferred crystallographic plane in the cubic lattice of the chromite. The effects of roasting time, temperature, soda to chromite ratio and particle size on the extraction of chromium are presented

Jun 18, 1905

By H. R. Thorpe

A floating gold dredge operating in coarse alluvial gravels of the Grey River on the west coast of the South Island, New Zealand, generated high concentrations of clay and colloidal particles in the dredge pond, which entered the groundwater system. Sampling was carried out at depths down to 20 m and it was found that variation of the length of the flow path occurred because of the movement of the dredge towards the piezometers. The alluvial gravels, the suspended sediments, the groundwater system and the water chemistry were all studied. Sediment concentrations were found to be highly variable with depth, but the relative concentrations in the depth profile were generally consistent as the flow distance shortened. The sediments were extremely fine and travelled further through the gravels than predicted. Comparison of field results with the available theory of deep filtration in clean beds of porous media gives some basis for estimating the behaviour of fine sediments in other alluvial systems

Jun 19, 1905

By W. P. C. Duyvesteyn, B. J. Sabacky

Reprinted with revisions from Extractive metallurgy of copper, nickel and cobalt, volume I: Fundamental aspects. ed. Reddy R.G., Weizenbach R.N. Warrendale, Pennsylvania: The Minerals, Metals and Materials Society, 1993. Development work on the Escondida process, concluding with the successful operation of an integrated leach-SX-EW pilot plant and a pilot flotation plant for the upgrading of leach residues, demonstrated that all major process objectives could be achieved. Extraction of 40% of copper in concentrates containing monovalent copper was achieved with essentially no oxidation of sulphide sulphur. The Cu contents of leach residues from four different types of concentrate were successfully upgraded to the original feed grades, giving a product that has potential as a high-quality concentrate for the smelter market. A compact solvent extraction section effectively recovered the ammonia lixiviant for recycling to leaching and selectively transferred Cu into a conventional acid sulphate electrowinning system. High-quality "six-nines" copper cathode was produced on commercial-scale stainless steel blanks, demonstrating that the process will be able to compete effectively in the premium cathode market

Dec 1, 1995

By D. W. Taylor, I. W. Farmer, N. Mojtabai

Rittinger's and Bond's descriptions of rock crushing relate the energy input required to fracture rock and the surface energy required to form new fractures to the change in specific surface area of feed and product during comminution. The potential applicability of this approach to blasting is illustrated, using the results of data from bench blasting tests on Pinal schists and production blasting of Carboniferous limestones. The approach contributes to understanding of the mechanisms involved in blasting and to the design of test blasts. A modified form is presented of the relationship between blasting energy, specific surface area of the muckpile and a rock energy constant related to the discontinuity structure of the rock. The modified equation fits observed data and offers a simple basis for further experiments

Jun 19, 1905

By I. L. Whyte

apparent density and drag coefficient of porous ores on

Apr 1, 1995

By G. G. Barbante

An understanding of the thermodynamics of smelting copper anode slimes is a prerequisite for improvements to the process. During slimes smelting, a silver-copper selenide matte is formed and subsequently oxidised to silver metal. As part of a series of investigations, molten silver selenide matte was oxidised at 1 100 degrees C with pure oxygen. The chemical potential diagram for the system was developed and used for qualitative prediction of the results of the experiments. A simple, computational thermodynamic model of converting is presented, the adjustable parameters of which were determined by matching the model with the experimental results. The practical usefulness of the model was demonstrated by predicting the effect on silver recovery of smelting temperature and of using either oxygen or air as the smelting gas

Jun 21, 1905

By A. T. Iannacchione

Underground mining of stone in the US is increasing, as is the depth of overburden above the mines. Data gathered from mine visits, maps, discussion with operators and numerical simulation have been used to investigate pillar design and recommend safe practice. Many pillars have slender shapes with relatively large adjacent mine openings: width-to-height ratios range from 0.54 to 3.13 and extraction ratios from 0.56 to 0.91. The pillar material is often very strong and average overburden only 80 m, but occasional failure due to excessive local stress has occurred where pillar size had been unintentionally reduced, overburdens were greater than 200 m, width-to-height ratios were less than 1.25 or extraction ratios were greater than 0.83. Pillars with width-to-height ratios of less than 1.5 appear more likely to fail under excessive stress. When width-to-height ratios fall below 1.0, defects such as through-running discontinuities can have a significant influence on stability. Dip, orientation and material properties are also important

Jun 21, 1905

By M. L. Leblanc, J. F. Burzynski, D. J. Mossman

A strong heterogeneity in the distribution of Sb+/-Au deposits exists within the North Atlantic Acadian-Hercynian domain. This is reflected in the regional disparity in Sb production among the various producing countries. This work focuses on the nature and distribution of Sb+/-Au occurrences in the Acadian-Hercynian domain. A summary listing of the general features of Sb-Au deposits found in this area is given

Dec 1, 1991

By R. J. Pine, J. S. Coggan

Distinct-element modelling has been used to study the mechanisms associated with observed deformation of the western face of the quarry. A complex failure mechanism involving distinct planar surfaces that was proposed for a slope failure in 1967 has been modelled and shown to be plausible. In addition, deep-seated flexural toppling may contribute to the slope instability. Modelling has confirmed the detrimental influence of a raised water-table on the stability of the slope and also indicates that the observed cyclic opening and closing of tension cracks may be attributed to seasonal rise and fall of the groundwater level

Apr 1, 1996

By M. J. Beus, B. Stewart, S. Iverson

Ore-pass hazards are a significant safety problem in US underground metal mines. From 1975 to 1995, nearly 75% of injuries during pulling or freeing of ore-pass chutes were related to falls of broken rock or the use of hand tools. Risk assessment methods are being used to identify the most probable causes of ore-pass failures and analyse the factors that result in malfunctioning or safety reduction. Static and dynamic loads are being measured in the laboratory and by field testing, with data from test ore passes compared with mine data to characterise true system behaviour. Computer modelling using closed-form solutions, finite element analysis and a newly developed particle flow code are being use to predict loads from ore and waste flow and impact. Preliminary results indicate that dynamic impacts may be much less than expected, as a result of damping factors, normal and shear stiffness and mass frictional characteristics

Jun 19, 1905

By D. M. Milne, P. J. Lunder, R. C. Pakalnis

During the mining of an open stope, deformation of the hanging-wall and the potential for dilution generally increase with the size of the exposed hanging-wall. Excluding discrete structures that may delineate unstable blocks, the mechanisms that drive hanging-wall deformation and possible dilution comprise several factors which can include elastic, plastic and discontinuum deformation. These stages of deformation are not mutually exclusive and at any point during mining all three of these mechanisms may be acting on the hanging-wall rock mass. Computer modelling techniques are available to analyse the three stages of deformation, but the difficulty lies in trying to obtain realistic rock mass properties for input and in determining when each stage of deformation is acting. Instrumentation data can be used to predict the effect of continued mining. However, it is often difficult to calibrate numerical models against field data owing to the large number of input parameters required. An empirical approach is recommended that uses two new parameters, the radius factor and the effective radius factor. A method is proposed for predicting the effect of continued mining from existing deformation and dilution data for a given hanging-wall

Apr 1, 1996

By R. J. Gochin, G. D. Schena, R. Spencer

The impact of a mineral project in a developing country is evaluated in the broad context of its economy using input-output models. Minimum economic theory is used to develop simple numerical models. Sets of technical coefficients are exploited in the development of linear models of the productive element of an economy. The analysis allows assessment of the overall economic consequences of a mineral development in which issues broader in scope than financial objectives need to be incorporated in the evaluation. In part 1, the framework for the development of the input-output model is presented. The model is refined to incorporate country-specific behaviour. The increased flexibility of the enhanced semi-input-output model permits a more confident investigation of the economy-wide effects associated with a new project in the mineral sector of a developing country. The relevance of the models is illustrated using an example from Namibia

Sep 1, 1991

By M. W. Robotham, H Wang

removal efficiency is analysed from a stochastic

Apr 1, 1995

By A. M. Tunstall, N. Djordjevic, H. A. Villalobos

The damage zone behind a typical smooth-wall blast in the open pit was assessed by visually examining diamond drill core to identify blast-induced cracking, mapping core rock quality designations to identify changes in fracture frequency and conducting uphole seismic testing to determine changes in rock mass characteristics. The results from the three techniques show reasonable correlation. They suggest that major damage, in the form of fracturing of intact rock, occurs at least 7 m behind the smooth-wall blast and significant damage, in the form of opening and extension of calcite-filled fractures, at least 12 m from the blast. At greater distances the dominant damage mechanism is the loosening of existent joints within the rock mass. In the trachytes at El Soldado these damage mechanisms correspond to peak particle velocities of 2 000, 900 and 500 mm/s respectively

Jun 19, 1905

By L. J. Cabri, J. M. D. Wilson, R Lastra

An image analysis program can search for gold minerals in polished sections by scanning about 100 x 100 back-scattered electron images at a magnification of x400, allowing gold grains as small as 1 micrometre in diameter to be detected. Typically, a c.15 h overnight search of a product smaller than 45 micrometres will scan c.1 500 000 particles, providing data that are not easily obtained through manual operation of an optical microscope. The program locates grains of the correct brightness, acquires gold X-rays from them by wavelength-dispersive spectrometry, filters the data to remove artefacts and record the images and stage locations for subsequent retrieval. At the end of the run, the program allows the operator to verify and identify the grains found. Industrial studies at Canmet have included determining the nature of gold in cyanidation tailings, checking the mineralogy and size of gold grains in samples from an Indonesian Cu-Au concentrator and locating and measuring gold liberation and grain sizes in an ore

Jun 21, 1905

By S. L. Gay

The conventional mass-balance equations used as constraints can lead to flow estimate values of zero even though the flow estimates should be some positive number. This is because many of the constraint equations are satisfied if the flow rates are zero. The way to overcome the problem is to use a slightly different form of the equations. For example, rather than use the conservation of flow of solids as a constraint it is better to use the constraint that the percentage of solids going into a unit equals the percentage of solids coming out of the unit. Examples are given using mineral processing data sets from Mount Isa, Queensland, and Red Dog, Alaska

Jun 21, 1905