Search Documents

By Richard H. Spencer

Since the passage of the Coal Mine Health and Safety Act of 1969, the Bureau of Mines has made many advances in mine communications. These efforts have resulted in the following developments and demonstrations: Surface-to-surface electromagnetic transmission of baseband voice signals through overburdens as deep as 600 feet. This transmission was achieved with equipment from the Interim Mine Rescue and Survival System Program, and demonstrated that baseband voice communications could be obtained through these overburdens in the absence of mine-generated noise; that is, when the mine power system was shut off, However, during mine operational conditions, the mine-generated noise proved to be so large that effective baseband voice communications to the desired depths could not be effected.

Jan 1, 1975

By K. L. Paciorek

The primary objective of this program was to determine the toxic fume and fire hazard of materials used in the construction of mine stoppings and in the sealing and reinforcing of mine ribs and roofs. The materials investigated were: silicone, phenolic, and isocyanate-based rigid foams, as well as epoxy and acrylate mine sealants. Of the rigid foams tested, the X-156 urethane foam presented the greatest toxic hazard based on toxic load values hydrogen chloride was the main toxic species evolved by this foam. In 'lone of the isocyanate-based compositions was hydrogen cyanide the major component, but its contribution increased with temperature. The FS-24 urethane and Celotex Max-Seal isocyanurate foams had the lowest toxic load values, although these two foams have different applications for in-mine use. Of the two mine sealants tested, the latex /acrylic coating presented the greater toxic hazard with acetic acid being the main toxic species evolved.

Jan 1, 1983

By Edmond Chin

The area encompassed by the political entities included in this study com-prises 11 million square miles or about 15 percent of the total Earth's land area. The bulk of the region is contained on the Asian continental land mass. Australia, the world's largest is-land or the world's smallest continent, alone is almost as large as the continental United States. The islands of New Zealand, New Guinea, Borneo, Sumatra, and Honshu are among the largest in the world. Collectively, they constitute a land area of 1.1 million square miles or an area about one-fourth the size of the United States. The region is noted for its great rivers. The Chang, Huang, Amur, and Mekong are respectively the fifth, sixth, eighth, and eleventh longest rivers in the world. The Ganges-Brahmaputra has created the world's largest delta, which covers 30,000 square miles. Abutting East Asia are the Sea of Japan, Dong Hai, Nan Hai, Bay of Ben-gal, and Arabian Sea. In the Southern Hemisphere, there is the Indian Ocean and the South Pacific Ocean. The Continental Shelf adjacent to the region constitutes a large proportion of the world's readily accessible shelf area. On the other hand, the Philippine and Java trenches and, further out, the Mariana Trench reach to formidable, abyssal depths, downward to 6,000 fathoms. Contrasting to this is Mount Everest, which reaches a lofty height of 29,028 feet. And then there is Xizang, whose high plateaus have been called the roof of the world.

Jan 1, 1992

By A. V. Hooker, E. J. Coggeshall

"The Bureau of Mines for some time advocated the firing of all blasts in coal mines as single shots, and this method of firing is the general practice in American bituminous-coal mines. All single shots can be fired with permissible single-shot units so designed that they will not ignite mixtures of methane and air.If several shots in a face are fired singly it is necessary to return the face after each shot. In some mines having steeply pitching coal seams, this may be dangerous or even impossible, under these conditions shots are usually fired simultaneously.Several shots cannot be fixed simultaneously with permissible single-shot blasting units, and safe types of multiple shots blasters are not readily available. This means that the firing of multiple shots in gassy mines is usually accompanied by the possibility of gas ignition as the blast occurs.Tests have been made at the Pittsburgh Experiment Station to determine the possibility of developing safe types of multiple-shot units suitable for such use, or of applying other type safely in gassy sections of mines where firing shots singly is impracticable.The tests may be divided into the following four groups:1. Tests to demonstrate hazard in the use of existing types of multiple-shot units of the portable generator type.2. Tests to show the electrical characteristics of multiple-shot generator units relative to the possibility of preventing igniting sparks and of modifying the design and application of such units in furthering safety."

Mar 1, 1935

By S. J. Gasior

Pilot plant studies showed the technical feasibility of fluidized-bed operation for producing hydrogen and synthesis gas by the steam-iron process. A mixture of iron and iron oxide from 20-to 100-mesh was partially reduced with a simulated producer gas and then oxidized with steam and/or carbon dioxide. Results of tests show the effects of pressure, temperature, bed height, gas-to-solids ratio, type of iron oxide, and composition of gas on the gas and solids conversions during reduction and oxidation. A baffled free-fall solids system was also found operable. The short residence time of about 5 seconds limited conversion of the solids.

Jan 1, 1961

By Neal M. Miur

"INTRODUCTION The Mineral Ridge-Clay Lick fault system in Crittenden and Livingston Counties, Kentucky, is one of the larger and more important fault systems of the Western Kentucky Fluorspar district. Total production from it up to July 1945 (chiefly since 1900) was approximately 80,000 tons of fluorspar ore, 10,000 tons of which came from the Mineral Ridge Fluorspar Co. tract 1, which was being operated by the Mahoning Mining Co. of Rosiclare, Ill. The fluorspar ore carries lead and zinc that can be recovered by milling, and the Mahoning Co. planned to log-wash the ore at the mine and then mill it in its mill at Rosiclare, The Mineral Ridge Fluorspar Co. properties were examined by O. M. Bishop, an engineer of the, Bureau of Mines, in August 1942. During 1943 and 1314, developments on the properties were under observation by X. B. Starnes, of the Bureau, and it was decided to diamond-drill tracts 1 and 2, as indications seemed favorable for opening up additional fluorspar ore bodies. Drilling was begun March 12, 1945, and was completed July 2, 1945, during which time 12 holed were drilled on tract 1 of the Mahoning Co.'s leases for a total of 3,637.1 feet, and one hole 359 feet deep was drilled on tract 2 of the Jennings lease. The Mineral Ridge-Clay Lick fault system, 4 to 47 feet wide, was encountered in all holes at 126 to 265 feet."

Apr 1, 1947

By S. R. Zimmerley, C. H. Schack

"INTRODUCTION The pilot-mill concentrator at Boulder City, which has a nominal capacity of 40 tons per day, was planned and built to investigate further the beneficiation of domestic manganese ores that have been concentrated successfully in the ore-dressing laboratory. As milling of manganese ores in general is a new field, it is necessary to prove the success of laboratory processes by means of large-scale operations employing standard milling equipment, and thus to obtain engineering and metallurgical data essential to designing and operation of full-scale concentrating mills.The first ore tested in the pilot plant was the Three Kids Annex manganese ore from the Las Vegas Wash area 15 miles southeast of Las Vegas, Nev. The deposit was worked for its high-grade ores during the First World War From 1930 to 1939, 4,500 feet of diamond drilling was completed by a private company. Diamond drilling started by the Bureau of Mines in November 1940 and completed in July 1941 aggregated 6,600 feet. Exploration by the private company and the Bureau outlined reserves of about 1,000,000 tons of ore assaying plus 28 percent manganese. A much larger tonnage of lower-grade ore also was outlined by the drilling.Because of its physical nature, the Three Kids Annex ore had long proved unamenable to concentration by ore-dressing methods. The ore is a mixture of manganese oxides (wad) filling the pores and to some extent replacing a silt composed of very fine grains of volcanic tuff, quartz, feldspars, other silicates, and clay. Some gypsum occurs as fillings along fracture planes. The ore is light and very porous. Upon wetting, it disintegrates into granular but friable particles and a large amount of slime. It is these characteristics that make the ore so difficult to concentrate."

Sep 1, 1947

By Don M. Coulter

"INTRODUCTION Bauxite, in Appalachian Alabama, occurs in the Rock Run and Goshen Valley districts in Cherokee County; in Nences Creek Valley near Jacksonville; near Anniston in Calhoun County; north of Fort Payne in DeKalb County; near Ashville in St. Clair County; and near Talladega in Talladega County.In February 1942, Preston E. Cloud, Jr., assistant geologist, Federal Geological Survey, began a study of these bauxite deposits and the geology relating thereto.The Bureau of Mines established field headquarters at Piedmont, Calhoun County, in July 1942. Mineral agreements covering a total of 11,097 acres were executed with 15 landowners in the Rock Run district; 38 in the Goshen Valley district, covering 7,575.5 acres; and 3 in the Nances Creek Valley district, covering 988.5 acres. Drilling was done on the properties of 9 land¬owners in the Rock Run district, and on the property of 1 landowner each in the Goshen Valley and the Nances Creek districts. Drilling began October 26, 1942, and ceased on May 17, 1943.Power drilling was supplemented by a labor crew that drilled hand-auger holes in shallow deposits and sampled .old shafts, mines, and mine dumps.In all, 222 holes for a total of 13,250 feet were drilled. Of these holes, 88 penetrated bauxite but too low in grade to constitute ore."

Mar 1, 1948

By Ronald B. Stotelmeyer

This report summarizes the U.S. Bureau of Mines evaluation of the mineral resources of eight roadless areas in several National Forests in Montana. The areas are amoung those that have been proposed as additions to the National Wilderness Presevation System In various sessions of the U.S. Congress. Mineral Commodities present include gold (lode and placer), silver, copper, lead, zinc, molybdenum, tungsten, rare-earth elements, fluorite, and barite. Numerous mineral deposit types occur. Past production was from gold placers and vein-type deposits. There is potential for development of large volume porphyry copper-molybdenum, disseminated gold, stratabound copper-silver, and exhalative massive-sulfide metallic deposits. A substantial increase in metal prices is needed before any known vein-type deposits will be economic.

Jan 1, 1994

By M. A. Schellhardt, E. J. Dewees, R. Vincent Smith

"INTRODUCTION Abnormal material requirements of the nation at war impose an intensive demand upon many irreplaceable natural resources. Natural-3as reserves) for example, are being subjected at the present time to extensive depletion by large-scale withdrawals of gas to supply unprecedented demands for fuel and raw materials for the synthesis of strategic products. Fluids produced from many so-called gas-condensate type reservoirs have become an important source of hydrocarbons vital to the war effort.Development of gas-condensate type reservoirs in Arkansas, Louisiana, and Texas in recent years created many problems not common to ordinary gas-producing operations. Early in the development of condensate-type gas fields, general practices were evolved and applied to insure efficient re¬covery of the hydrocarbons existing in the gas phase under initial reservoir pressures and temperatures, put often the practices were predicted mainlyregardingupon generalized theory regarding the behavior of the fluids and were not always the most efficient, because field and laboratory procedure for testing these hydrocarbons had not progressed as rapidly or as far as field development. Specific information regarding the composition and properties of fluids ultimately recoverable from many gas-condensate reservoirs, especially, is lacking."

Oct 1, 1944

By L. D. Schmidt, Wm. Seymour, W. S. Landers

"INTRODUCTION The relative value of the various individual physical and chemical properties of coke as a measure of its performance in the blast furnace as aroused considerable controversy but it is generally agreed that uniformity in these properties is extremely important if maximum mum pip-iron production is to be attained. The control of,the bulk density or weight per cubic feet of the coal charge in the coke ovens is a major, and frequently overlooked, factor in producing a uniform product and in efficient operation of the coke plant.This report presents a brief discussion of the general problem of bulk-density control and the results of tests on samples of coke-oven charges from several operating plants experiencing difficulties due to lack of adequate control. These tests covered the effect of moisture and oil content on the bulk density of the coal. Some tests on the effect of a wetting agent and furnenous of gained were also made. A description of the methods used to determine the bulk density of the coals studied in this investigation and of the methods used to apply oil to the coal at byproduct-coke plants are included in this product. No theoretical analysis of the data presented in this report, because the primary purpose of the investigation was to obtain data of immediate practical value to the plants concerned."

Apr 1, 1945

By T. T. Read, F. C. Houghten

"The bad effects upon the health and output of miners that result when the ventilating current in a mine lacks sufficient cooling power have been described by Harrington and Sayers in a previous report (1)*** The normal temperature of the human body is about 98.5°F. and whenever work is done by the muscles, indeed even when sitting still, the normal bodily processes generate heat which must be given off, otherwise the body will become overheated and a number of bad effects will be produced. If it were possible to so enclose a man that he could continue to breathe and no heat could escape from his body he would die within a short time. In a series of experiments made at the Pittsburgh Station of the Bureau of McConnell and Houghton (2) found that a dry-bulb and a wet-bulb temperature of 112.5°F could he borne for only 35 minutes, even when the subject was at rest. A wet-bulb temperature of 100.4°F (dry-bulb 157°F) could only be tolerated for 45°F minute. Under such conditions the bodily temperature rises as much as 45°F above normal and the pulse is accelerated. Very uncomfortable sensations are felt when the pulse rate exceeds 135. The human body, like any other internal combustion engine, must be cooled in order to function properly.Under ordinary circumstances the air surroundings people is enough coder than themselves to permit this heat generated within the boiy to be river off with¬out difficulty. At higher temperatures, or when the rate of work, with its corresponding generation of heat is high, the body can not throw off heat fast enough, so it begins to sweat and the evaporation of the sweat cools the body. But the results of the experiments cited above indicate that in still air, even with the body at rent, it can not adjust its temperature when the air is above 90° wet- bulb. J. S. Haldane (4) says ""at a wet-bulb temperature of 60°F the actual amount of work done by the miner begins to fall off; as the wet bulb temperature rinse farther the work Bona gradually diminishes to the vanishing point. Then the temperatures indicated by the wet-bulb exceeds 85°F hard work in a mine seems hardly or the commercial working of a mine the wet-bulb thermometer should not in generaI, be allowed to rise above 80°F, unless perhaps where there it a good current."

Dec 1, 1923

Prier to the date of this contract, Ocean Energy had developed and demonstrated a high efficiency fluorescent caplamp which operated from a standard 4 volt miner's caplamp battery. This unit produced about five times the light output of the standard incandescent miner's caplamp. The Company believed that the major market for this unique caplamp was in the industrial and municipal applications. Because of the additional safety requirements for coal mining use, and in conjunction with the much smaller market in the mining industry, the additional expense and difficulty of modifying this caplamp to comply with the Federal and State coal mine regulations were not considered at that time. Recognizing the potential of this lamp for improving illumination conditions for underground coal mining, the US Bureau of Mines contracted with Ocean Energy to make the required modifications to this lamp to bring it into compliance with the Federal and State of Pennsylvania regulations, and thereby, make this lamp available to the anthracite and bituminous coal mining industry. At the outset of the contract, the injection molds for the caplamp housing were being completed, and only prototype, hand fabricated, units were available for tests. The Bureau evaluated these prototype units and formulated a performance specification for the miner's version. Light level and distribution, weight, size, angle of tilt, and operating duration were all specified. In addition, it was required that the caplamp be com¬patible with existin charging equipment at the mines and that the final design be in full compliance with MESA Schedule 6D and he ultimately approved by MESA, Approval and Testing, as well as by the Pennsylvania Bureau of Deep Mine Safety. The scope of this contract covered the modifications required to achieve these objectives. It was agreed by the Bureau that all rights to the lamp, including design, material combinations, circuitry, etc. would remain with Ocean Energy. The charger/adapter system and components, which were developed under contract funds, are disclosed hero and become public knowledge and property. Patent applications have been filed by Ocean Energy to protect the mechanical and electrical design aspects of the lamp. It should be noted that this report contains details, designs and data which may be covered by one or more Ocean Energy patent applications, and disclosure herein is made only to provide better understanding of the contract results.

Jan 1, 1975

By Oliver C. Ralston, and others

"INTRODUCTION Investigations of the Nonmetals Division are now conducted at College Park, Md.; Tuscaloosa. Ala.; Seattle, Wash.; and. Norris, Tenn. The last of these was acquired, this year by arrangement with the Tennessee Valley Authority and is engaged in electrothermel research, using power generated by the T.V.A. and. raw materials from that region. In general, the work of the division is concerned with dressing nonmetallic minerals end utilizing the products there-from. Coal, salts, and waters are investigated, and the suitability of apparatus and equipment is studied.As the Metallurgical. Division of the Bureau of Mines makes routine tests of certain nonmetallic ores under prescribed conditions for the public if they are of general interest, the published reports of that division should be read and thus, with the reports of tile Nonmetals Division, the whole field may be covered."

Oct 1, 1939

By H. S. Auvil

[The shrinkage of coke after formation is one of the variables that affects the net expansion of the change in both industrial and test ovens. Various test results have been interpreted as indicating that cokes from certain coals shrink to a marked extent and that other cokes show very little shrinkage; out no comprehensive experimental study of the shrinkage of coke after its formation and of the factors influencing this shrinkage has come to the attention of the authors. While investigating the reactivity of cokes made by the BM-AGA method,6/ Reynolds7/ found that granular low-temperature cokes shrink considerably then reheated to higher temperatures. This shrinkage was large enough to influence the behavior of the charge (net expansion or contraction) in a coke oven to a marked extent. Since that time the Bureau of nines has investigated the shrinkage of coke different methods, all of thick had one common objective - the elimination of the effect of other factors, such as swelling in the plastic range, which could either partly or completely mask the shrinkage of the coke. Only parts of these studies have been published8/9/ in abbreviated form in]

Jan 1, 1940

By N. Kumar Kittusamy

The purpose of this study was to assess the adequacy of the cab design and to determine the percentage of musculoskeletal symptoms among workers. A questionnaire was designed to assess demographics, work information, job history, and musculoskeletal symptoms in operators of heavy construction equipment. Information concerning equipment included design of the seat/chair, levers, pedals, bothersome vibration, quality of egress from the equipment, proper preventative maintenance and repairs, and age of the equipment. The body regions that were evaluated included the neck, middle/upper back, low-back, shoulder/upper-arm, elbow/forearm, wrist/hand, hip, knee, and ankle/foot. One hundred and eighty nine operators completed the questionnaire. The results indicate that these workers are at risk for developing musculoskeletal disorders, the need to perform a larger survey to further substantiate the outcome, and the need to quantify risk factors (i.e., whole-body vibration and static sitting postures).

Jan 1, 2003

By J. E. Conley

Available statistics show that the demands of the American chemical industry for sodium sulphate have been increasing slightly in recent years. The supply from domestic sources, particularly In the form of byproduct salt cake from the acid manufacturers, has been tending to decrease due to the growing manufacture of synthetic acid. Both hydrochloric and nitric acids are being synthesized from their elements. The natural result has been that a smaller amount of salt cake is available. Simultaneously, the expansion of the Kraft paper industry, especially in the South, has brought about greater demand for sodium sulphate in that section. This dean is being met by domestic byproduct salt cake, by imported German sodium sulphate made from potash waste liquors, and by favorable situated domestic deposits of Glauber salts and tile anhydrous salt, thenardite. No shortage of natural sodium sulphate exists in the United States, but usually such deposits occur in semiarid regions far removed from transportation facilities and from markets. Moreover, the major portion of the natural deposits is Glauber salt or mirabilite (Na2SO4 ? 10H20), which must be dried or dehydrated in order to meet consumer requirements. The water of hydration represents, roughly, 55 percent of tae total weight of the crude salts and therefore has a very important influence on transportation costs. In marry instances the cost of getting, even the dehydrated product to market is the deciding economic factor. Therefore, the recovery oil production of anhydrous sodium sulphate from plant-.waste liquors or from natural brines of suitable composition might be economically feasible. The U.S. Bureau of Mines, at its nonmetallic Minerals Experiment Station, New Brunswick, N. J., has, for a number of rears, been investigating the commercial possibilities of treating the complex saline mineral polyhalite (K2SO4?NgSO4?2CaSO4?2H20) for the recovery of potash and magnesia. Certain proposed processes (1, 2, 3, 4)4/ yield waste liquors that contain the bulk of the magnesium and sulphate originally combined as magnesium sulphate in the polyhalite molecule. Sodium chloride In limited concentrations is also present, as extensive beds of salt occur in strata overlying the polyhalite deposits. A typical waste liquor would contain:

Jan 1, 1936

By R. V. Higgins, G. B. Shea

"FOREWORDIn the second year of World War II, the petroleum industry in California was taxed to near capacity to satisfy the expanded war demand for petroleum products, particularly fuel oil. With discoveries of crude oil in California declining and known reserves being depleted rapidly, conditions appeared to warrant study of the possibilities of utilizing the outcropping bituminous sandstone deposits in California for obtaining new sources of oil if the war should he prolonged. At conferences in Washington, D. C., with members of the Petroleum Administration for War and the Geological Survey, Bureau of Mines engineers emphasized the importance of determining the extent of those outcropping deposits of oil-impregnated rocks and of developing a practical process for commercial recovery of the contained bitumen to assure, if necessary, a supplementary supply of fuels. The desirability of such a study was recognized, and in July 1943 the Petroleum Field Office of the Bureau of Mines at San Francisco, Calif., in cooperation with the Geological Survey and the Petroleum Administration for War, initiated a study of the bituminouss sandstone problem. It was agreed that all mapping and geological work in connection with the study would be done by the Geological Survey, all engineering studies in developing a process for extracting the oil would be carried out, by the Bureau of Mines, and that the Petroleum Administration for War would aid in final adoption of the results in the field if circumstances warranted such action.Deposits of bituminous sandstones in California occur principally in the immediate region of the Coast Range mountains, notably at Pt. Arena, in Mendocino County, about 110 miles north of San Francisco; near Santa Cruz, in Santa Cruz County; in the Edna area in San Luis Obispo County; in the Sisquoc area in Santa Barbara County; and in the Ojai and Santa Clara Valleys in Ventura County. 4/ In addition oil-bearing sands outcrop near McKittrick and Maricopa, in western Kern County, and along the east edge of the Kern River oil field. Among the several prominent deposits of these source materials, those occurring near the cities of Santa Cruz and San Luis Obispo, and the town of Sisquoc are the largess."

Oct 1, 1948

Isometric strength is defined as the capacity to produce force or torque with a voluntary isometric (muscle[s] maintain[s] a constant length) contraction. The key thing to understand about this type of contraction and strength measurement is that no body movement occurs during the measurement period. The tested person's body angles and posture remain the same throughout the test. Isometric strength has historically been the type most studied and measured. It is probably the easiest to measure and to understand. Some strength researchers feel that isometric strength data may be difficult to apply to some "real life" situations because in most real circumstances people are moving - they are not static. Other researchers counter that it is equally difficult to determine the speed of movement of a person or group of persons doing a job (each moves in his or her unique manner and speed across the links and joints of the body). Thus, dynamic strength test data collected on persons moving at a different speed and/or in a different posture from the "real world" condition will be just as hard to apply. In truth, neither is better - they are different measurements. Both researchers and users should collect and use data that they understand and that fits their application. Workplace Assessment When a worker is called on to perform a physically demanding lifting task, the external load produces moments - tendencies to produce motion, also called torques - about various joints of the body.(1) Often these moments are augmented by the force of gravity acting on the mass of various body segments. For example, in a biceps curl exercise, the moment produced by the forearm flexors must counteract the moment of the weight held in the hands as well as the moment caused by gravity acting on the forearm's center of mass. To perform the task successfully, the muscles responsible for moving the joint must develop a greater moment than the combined moments of the external load and body segment. It should be clear that, at each joint of the body, there is a limit to the strength that the muscle can produce to move ever-increasing external loads. This concept forms the basis of isometric muscle strength prediction modeling.(1) The following procedures are generally used with this biomechanical analysis technique. First, workers are observed (and usually photographed or video-taped) as they perform physically demanding tasks. For each task the posture of the torso and the extremities are documented at the time of peak exertion. The postures are then re-created using a computerized software package, which calculates the load moments produced at various joints of the body as the task is performed. The values obtained during this analysis are then compared to population norms for isometric strength obtained from a population of industrial workers. In this manner, the model estimates the proportion of the population

Jan 1, 1998

By R. A. Egen

The purpose of this book is to provide an indication of what good hoisting practice is and how it might be achieved. To this end the book contains discussions of equipment and inspection and maintenance procedures developed and used by mining people in striving for safe, reliable hoisting equipment. Most of this information comes from domestic practice; the rest is foreign, notably from Canada. Most things discussed have long proved their general worth, and others promise to; a few are beginnings. However, nothing is conjectural or theoretical; the practices described herein are in use somewhere in the mining world. The stress is on equipment in use; it is not a design-guidelines manual. Nevertheless, there are some sections dealing with design material since it may be of value in a maintenance/ replacement sense. Mine hoisting installations encompass such a wide variety of equipment and conditions that it is impractical to specifically cover them all. This book mainly treats conventional systems using conventional components with some discussion of the more common unconventional (special) systems in use. There is no recognized definition for a "conventional" mine-hoisting system. Herein the term means those systems most commonly used in daily operations for transporting men, materials, and product-electrically driven drum and friction hoists, with guided conveyances running in vertical or inclined shafts. Beyond this, what "conventional" means is probably best illustrated by the topics discussed.

Jan 1, 1975