Search Documents

By D. E. Pollock, J. A. Organiscak

Water sprays and water powered scrubbers have both been utilized in the mining and milling industry to suppress airborne dust. Unconfined water sprays operated at lower water pressures of ?689 kPa (?100 psig) can be very effective at wetting the mine product at the dust source and significantly reducing the amount of respirable dust that becomes airborne. However, unconfined waters sprays can be somewhat ineffective in actually removing airborne dust from the air. On the other hand, water powered scrubbers operating at higher water pressures of ?1,724 kPa (?250 psig) in physical enclosures or ducts have previously been demonstrated to be very effective in removing airborne dust from the air. These higher operating water pressures are uncommon in many mines and mills, so their use is limited. The National Institute for Occupational Safety and Health (NIOSH) recently investigated the performance of a lower-pressure, water powered inline series spray scrubber for removing localized airborne dust emitted at the source. Results showed noticeable improvements in airborne dust capture efficiency through the operation o f multiple inline series hollow cone spray nozzles within a round duct or pipe at the same water pressure as a single spray. Operating hollow cone spray(s) at higher water pressures noticeably improved airflow through the scrubber and yielded some additional scrubber efficiency improvements. Thus, in-line spray scrubber efficiency trade-offs were observed to be made by altering spray power components of water pressure and/or quantity (number of sprays). Results show that, on average, up to 0.23 and 0.32 m3/s (484 and 679 cu ft per min) of airflow at 0.81 and 0.69 dust capture efficiencies can be achieved with three 81° and 33°hollow cone inline series sprays, respectively, operating at 1,655 kPa (240 psig).

By Eleanor Abshire

THIS PUBLICATION is the third to be prepared as a result of a cooperative project by the Bureau of Ships and the Bureau of Mines for accumulating literature published on zirconium and hafnium. The undertaking also resulted in the establishment of an information center on zirconium and hafnium at the Bureau of Mines station at Albany, Oreg., for the use of research organizations and others. The present bibliography consists of references (with abstracts) to pertinent literature on zirconium. The first publication in this series was Information Circular 7771, Bibliography of Zirconium, published in April 1957. It consists of 969 abstracted reports and 645 U.S. and foreign patents. The second publication, called a supplement to Information Circular 7771, is numbered Information Circular 7830 and consists of 844 abstracted reports and 62 U.S. and foreign patents. It was published in October 1958.

Jan 1, 1962

By T. J. Batchler, T. M. Barczak

The Code of Federal Regulations (CFR) requires that the transverse load capacity of stoppings be equal to or greater than traditionally accepted in mine controls, which for block stoppings is generally accepted as 39 psf as referenced in the preamble to the CFR standard. This measure is based on physical testing of a freestanding wall in accordance with ASTM E 72 specifications, where our past research has shown that the dominant parameter is the tensile strength of the sealant. A new protocol based on rigid arch loading of the structure is proposed to determine the true transverse load capacity of block stoppings. Arching is achieved by the restraint of the stopping against the mine roof and floor, whereby compressive forces are developed within the wall. A laboratory procedure using the NIOSH Mine Roof Simulator (MRS) to simulate rigid arching of block stoppings was developed and results verified through full-scale in-mine tests. The rigid arch tests have demonstrated transverse load capacities more than an order of magnitude higher than the ASTM E 72 evaluation method from which the 39-psf requirement is derived. More importantly, the rigid arch tests have shown that the load capability is dependent on the physical properties of the block and geometric properties of the wall and not the sealant.

By Joseph H. Bilbrey

COBALT is a silvery gray metal which closely resembles nickel in appearance and properties although it is somewhat harder and more brittle. It is rather widely disseminated and is estimated to make up about 0.001 percent of the earth's crust as compared to 0.020 percent for nickel. Cobalt, one of the four ferromagnetic elements, is used for many magnetic applications. It is oxidation resistant, a property which when coupled with its moderately high melting point of 1,495° C., makes it useful in high-temperature applications. Although cobalt had been used by man as a coloring agent for glass and other ceramic products for 4,000 years, it was not isolated as a metal until 1742 and not established as an element until some 40 years later. Early in the 20th century, cobalt began to be used in alloys, and soon these applications displaced ceramics as the major consumer of cobalt. The use of cobalt in alloys gave considerable stimulus to production, and the world output of cobalt increased rapidly, rising from 400 tons in 1920 to 1,400 tons in 1930 and 5,500 tons in 1940. With the advent of the jet plane in the mid 1940's and the consequent increased need for cobalt-bearing high-temperature alloys, cobalt production again increased, reaching 7,900 tons in 1950. The increased demand for cobalt during the Korean war coupled with a large demand for stockpiling caused world production to more than double within the next 10 years, reaching a peak of 17,300 tons in 1959.

Jan 1, 1962

By Christopher Mark

Perhaps the most significant development in coal mine ground control during the last century was the introduction of roof bolting during the late 1940’s and 1950’s. From an engineering standpoint, roof bolts are inherently more effective than the wood timbers they replaced. Roof bolts promised to dramatically reduce the number of roof fall accidents, which then claimed hundreds of lives each year, and they were initially hailed as “one of the great social advances of our time.” Roof bolting also emerged at a time of rapid technologic transformation of the coal industry, and greatly accelerated the transition to trackless, rubber-tired face haulage. The U.S. Bureau of Mines quickly became the new roof support’s strongest advocate. Some state agencies and miners were skeptical at first, but nearly everyone was soon won over. Case histories were reported showing that roof falls could be largely eliminated while productivity increased dramatically. Little wonder that, in the words of one contemporary observer, “roof bolting has been adopted more rapidly than any other new technology in the history of coal mine mechanization.” Yet by the end of the 1950’s, it was clear that roof fall fatality incidence rates had actually increased. It would be another decade before the superior ground support provided by roof bolts would clearly save lives. The story of how roof bolting was implemented by the mining industry, but took so long to live up to its promise, is a fascinating example of the interaction between economics, technology, regulation, and science. It still has important lessons for today.

By Richard J. Mainiero, James H. Rowland

When most people think of explosives transport they think of a hazardous operation. We all know that we aren’t allowed to transport explosives through tunnels and are discouraged from traveling through heavily populated areas. Popular opinion suggests that explosives transport is a very risky operation. The authors decided to look into this a little more thoroughly and found just the opposite to be true. While there have been some disastrous world-wide accidents involving the transport of industrial explosives, this is not the case in the U.S. Over the past 10 years, accidents related to the transport of explosives used in mining and construction have resulted in 5 major injuries, 11 minor injuries, and no fatalities. Explosives and ammonium nitrate (AN) transport outside the U.S. has not had such a good record; there have been 4 major explosives or AN transport accidents resulting in a total of more than 300 deaths. Most of these fatalities could have been prevented if the accident site had been evacuated once the explosive or AN cargo began burning. The safe history of explosives and AN transport in the U.S. is due to diligent efforts by government, labor, and industry. However, accidents will become more common and disastrous if we become complacent.

Education and training research is a major component of the Bureau of Mines human factors research program. The goal of human factors research is to enhance human performance for the purpose of improving both safety and the profitability of the minerals industries. This is achieved through the design of mining equipment, work tasks, management procedures, and development of human resources. This proceedings volume presents several new developments that are helping to improve the quality and efficiency of health, safety, and occupational skills training in the mining community. Several papers address the issue of how to teach and assess miner abilities to deal with underground mine emergencies. Other papers examine practical procedures for defining and cost justifying the integration of structured training and other performance improvement strategies to enhance the proficiency of the work system.

Jan 1, 1988

Objective To develop safety training tools for mine health and safety trainers that fill gaps in currently available materials and help capture the wisdom and knowledge of “expert miners.” Background NIOSH began a series of stakeholder meetings in 1998 to determine what research was needed to improve miner health and safety. One of the more common concerns among stakeholders was a critical lack of appropriate training materials applicable to metal/nonmetal mining. Participants provided many insights into what effective training materials should include and how materials could best reach both new and experienced miners. The most important factors were that any materials be realistic and interesting and that some way must be found to capture the wisdom of expert miners before they retired. Approach NIOSH researchers chose videos as the best means of achieving these training goals. Over the past 3 years, NIOSH has produced three training videos that present information on safe work practices in underground mines: handling explosives, recognizing roof hazards and using proper scaling techniques, and installing ground supports. The last two videos, “Rock Falls—Preventing Rock Fall Injuries in Underground Mines” and “Miner Mike Saves the Day—or—Ground Support…It’s Important,” have won Alice Hamilton awards, NIOSH’s highest recognition of Excellence in Occupational Safety and Health, in the Educational Materials category. Two new videos are now being released. Both of these videos were shot completely in operating underground hard-rock mines and used expert miners to tell the story. Hazards In Motion The first, “Hazards in Motion,” deals with the dangers of working around mobile equipment in an underground mine. Ben, a new trainee, refuses to pay attention in his 40-hour New Miner Training class, and when the class takes its first trip underground, he wanders off and finds himself in many dangerous situations. He encounters many experienced miners who both chew him out for his unsafe attitude and give him advice and information on how to survive around mobile equipment. Many common pieces of equipment are shown, including haulage trucks, LHD=s, tracks and trains, slushers, skips and hoists, and air doors. The dangers of ignoring signals and of horseplay are also included. After nearly losing his life numerous times, Ben learns his lesson with the help of the Safety Angel, an experienced miner who looks suspiciously like his safety trainer. Ben’s Safety Angel saves his life repeatedly, teaches him how to work safely around these common conveyances, and introduces him to experts who have specific safety tips. Ben learns the error of his ways and vows to be the safest miner in the mine. “Hazards in Motion” is approximately 30 minutes long. Hidden Scars The second video is the first in the NIOSH “Expert Miner” series. “Hidden Scars” is a narrative interview with Don Capparelli, a miner and supervisor at the Sunshine Mine in north Idaho. This video captures the story of a fatal rock burst in May 1994, when Don was seriously injured and his long-time partner, Jimmy Findley, was killed. “Hidden Scars” is a very powerful story. Don Capparelli shares the physical and emotional pain he lives with daily as he relates the events leading up to the rock burst that took the life of his best friend and partner. This video is an excellent reminder of the human cost of uncontrolled accidents and the hidden scars that survivors must deal with for the rest of their lives. It runs approximately 25 minutes.

Jun 1, 2001

By William F. Keyes

Greensand, which is widely distributed in the Eastern United States, was produced in 1975 only by Inversand Co., a subsidiary of Hungerford & Terry, Inc., near Clayton, N.J. Production and sales information are not available for publication. Raw greensand produced by the company was sold for agricultural use as a soil conditioner. Processed greensand was used by manufacturers as filter media in equipment for the removal of manganese, iron and other elements from water. The University of Delaware received a grant of $17,051 from the Bureau of Mines early in 1976 to continue its studies of the effectiveness of greensand in removing metallic contaminants from waste waters.

Jan 1, 1977

Pillars with width to height ratios of less than 1.0 are frequently created in underground hard rock mines. The strength of slender pillars can be estimated using empirically developed equations. However, the equations can provide variable results when the width-to-height ratios approach 0.5. This paper investigates some of the issues affecting pillar strength at low width-to-height ratios in hard brittle rock. The investigation includes an evaluation of empirical pillar strength data presented in the literature and observations of pillar performance in underground limestone mines in the eastern United States, supplemented by numerical modeling in which failure processes and sensitivity of slender pillars to variations in rock mass properties are evaluated. The results showed that the strength of slender pillars is more variable than that of wider pillars. The numerical model results demonstrated the increasing role of brittle rock failure in slender pillar strength. The absence of confinement in slender pillars can result in a fully brittle failure process, while wider pillars fail in a combined brittle and shearing mode. The onset of spalling in slender pillars occurs at or near the ultimate strength, while this is not the case for wider pillars. Slender pillars are shown to be more sensitive to the presence of discontinuities than wider pillars, which can partly explain the increased variability of slender pillar strength. Two examples are presented, which illustrate failure initiation by brittle spalling and the sensitivity of slender pillars to the presence of discontinuities.

By T. A. Klinefelter

KYANITE and the related minerals sillimanite, andalusite, dumortierite, and topaz are natural aluminum silicates that can be used in production of mullite (3A1203?2Si02), a superduty refractory material. Kyanite and sillimanite are the dominant ones because of their greater abundance. The only other kyanite-group mineral presently used for mullite production is andalusite. Mullite is not an absolutely essential material as other refractories can be used in the same heat range. However, it is a highly satisfactory one. It is the only compound of silica and alumina that is stable at high temperatures. It has low thermal expansion and is very resistant to corrosive melts and to thermal shock. For these reasons mullite refractories have a much longer life than standard fire-clay refractories under the same conditions. Worldwide, excluding U.S.S.R., the refractories industry consumes about 150-000 short tons annually of kyanite group minerals and synthetic mullite.

Jan 1, 1961

By H. M. Lawrence

"Florida, the State that supplied 82 per cent of the phosphate rock sold in the United. States in 19284, has two producing areas - the hard-rock and the land pebble districts. Production of the hard-rock field, decreasing importance in recent years, is now confined to mines near Dunnellon, in Marion and. Citrus Counties. The land-pebble district, with a production of almost 80 per coat of the nation's requirements, is located, in Polk and Hillsborough Counties. In the land-pebble area the phosphate deposits - probably Pliocene in age, derived by marine action from underlying, older, phosphate-bearing formations - consist of beds of phosphate matrix, covered by practically barren sands and clays. The overburden, ranging in thickness up to 45 feet, is removed by hydraulic methods or by drag-line excavators. The matrix, ordinarily less than 25 feet in thickness, is mined by hydraulicking and is pumped to adjacent washing plants for beneficiation. The dried product of the washing plants is the Florida pebble rock that is sold in foreign as well as domestic markets.The beneficiation of phosphate ores in the land-pebble district of Florida has been largely limited in the past to the recovery of the coarser pebbles. By washing and screening the crude matrix a separation is effected at about 20 mesh (0.033 inch). The coarser material is the phosphate-rock product of the plant and the finer material is discarded. The amenability of the washer- rejects to treatment by other processes is being investigated. Of methods that may have some application to the treatment of the low-grade phosphatic sands that comprise the greater portion of the washer-rejects, gravity concentration has received some study.Laboratory experiments to determine the amenability of phosphate sands to gravity methods of concentration were first performed in October, 1927. Later, in the winter of 1928-1929, a further series of teats was made,. In these later tests phosphatic sands were concentrated by hydraulic classification, and. also by hydraulic classification followed by tabling. In these experiments concentrates with an analysis above the minimum grade of commercial phosphate rock (66 per cent bone phosphate of lime - B.P.L.) obtained. The recovery of the phosphate varied but was promising enough to warrant further study. A more comprehensive investigation was therefore outlined. This paper presents the results obtained from an investigation, of classification and tabling of phosphatic sands recently completed by the United States Bureau of Mines Su cooperation with certain Florida phosphate companies, the Missouri School of Mines and Metallurgy, and the University of Alabama."

Jul 1, 1930

By Ignaz Lichtig

[IN CONNECTION with its work on the conversion of coal to liquid cud gaseous fuels,3 the Bureau of Mines has always striven to keep informed of developments in this and related fields so that unnecessary duplication of effort could be prevented and so that useful ideas, presented in scientific and technical literature, could be evaluated as quickly as possible. Thus the E has compiled expensive literature and patent abstracts on the Fischer-Tropsch synthesis4 and hydrogenation d e venation of coal at elevated h temperatures and pressures.5 6 This publication differs from the references just given in that it covers patent applications, which may or may not have been approved for issuance as a patent, and also includes later material. The patent literature is, of courses, a valuable source for new ideas. German patent, have been particularly useful in this field because both processes for the complete conversion of coal to fluid fuels originated in Germany and were thoroughly investigated there because of the shortage or of indigenous fluid fuels. Among the German literature relating to these processes are patent applications. In contrast to the United States, Germany has a system in which applications are published before the final patents are issued. This arrangement permits the public to view all the applications and not just those for which a patent was granted as is done in the U.S. system. When main of the invention are judged not patentable by the German Patent Office, such documents nevertheless may contain useful ideas for scientists and engineers.]

Jan 1, 1961

By Stephen C. Tadolini, Dennis R. Dolinar

The risk of injury caused by minor roof falls continues to increase in underground mining. Most ground control injuries result from small rock falls that occur in a supported area, but do not involve the failure of the support system. In the roof, these are the "skin failures" that occur between previously installed primary or secondary bolting systems. To minimize skin failures and the associated accidents, several devices were designed and tested in the laboratory to maximize stiffness, minimize material thickness and weight, and ease material storage and handling on roof bolting machines. The goal of this project was to design and evaluate devices that can be installed with traditional primary or secondary roof supports, and that are easy to handle/install under temporary or previously supported roof.

By Anthony T. Xannacchione, Luis E. Vallejo

At present, there is little knowledge concerning the shear strength of clays containing floating rock particles with concentrations from 0 to 30%. In practice, the effect of rock particles is typically disregarded in shear strength analysis The two primary reasons for this are: 1) a lack of agreement concerning the influence of rock particles on material strength, and 2) the expense and difficulty of testing day-rack mixtures with existing laboratory procedures. These factors have impeded the development of successful slope remediation design techniques far colluviums derived from resistant sedimentary rocks or spoil produced from surface mining. This study reviewed 3 1 technical papers which contain analysis of shear strengths for clay and sands with varying mixtures of rock particles. These technical papers, published over the last 40 years, are comprised of field case studies, laboratory evaluations, and theoretical analysis. Evaluation of this body of knowledge ha shown that the shear strength gradually increases with increasing percentages of floating particles in unsaturated clays.

By T. F. Anstett

The Bureau of Mines estimated the potential availability of tungsten from 57 mines and deposits in 19 market economy countries. The tungsten resources of China and the U.S.S.R. were also estimated. This resulted from an evaluation of tonnage-cost relationships indicating the quantity of tungsten available as ammonium paratungstate (APT), artificial and natural scheelite, and ferrotungsten at various average total costs of production including 0- and 15-pct rates of return on invested capital. The evaluated deposits contain 1.2 million metric tons (t) of recoverable WO3, of which approximately 52,000 t of AEYT can be produced at the January 1983 market price of $5.37/lb, 89,000 t of natural and artificial scheelite at a market price of $3.63/lb, and 1,700 t of ferrotungsten at $5.61/lb of tungsten. An annual availability analysis indicates that by the early 1990's new deposit discoveries, development of known prospects, or expansions of producing mines will be necessary to meet projected tungsten demand.

Jan 1, 1985

By J. W. Paul, J. N. Geyer

"GENERAL STATEMENTThe purpose of this report, which is the first of a series of three covering mines in the Fairmont district of West Virginia, is to give the result of a' study conducted in seal mines to ascertain the nature of the safeguards employed to prevent injury to the workmen from falls of roof and coal. In presenting the subject matter, consideration must necessarily be given to factors, features, and conditions such as method of mining, timber regulations and practices, supervision and natural conditions; and, for comparative purposes, a certain amount of statistical matter bearing upon the relation of fatalities and injuries to their causes, tonnage produced, men employed, days worked, and time lost.Those features and practices found to promote safe protection are summarized and suggestions made for such additional safeguards and practices as appear to give greater protection against injury from falls of roof or coal.ACKNOWLEDGMENTSThis study of falls of roof and coal in mines in Harrison County has been conducted by the U. S. Bureau of Mines in cooperation with R. M. Lambie, chief of the Mining Department of the State of West Virginia who assigned L. W. Brown, a district mine inspector, to assist in the field work and in the preparation of individual reports on each mine visited in this study. The writers acknowledge the helpful suggestions and cooperation given by these officials, the latter of whom assisted in the field work and prop red most of these sketches for the individual reports which wore submitted to the operator by the chief of the department. Thin report is a summary of the contents of the individual reports heretofore furnished the individual operator."

Aug 1, 1931

By Russell R. McLellan

As part of an effort to develop new or improved placer mining technology in the Tertiary gold-bearing channel gravel of northern California, the Bureau of Mines conducted investigations at the old Badger Hill placer mine in Nevada County, Calif., to collect data and information regarding drilling and sampling methods and deposit characteristics. Sampling studies involved the collection and processing of 400 tons of large-and small-volume samples from drill holes, underground workings, surface pits, and blasthole rounds. A total of 355 samples averaging 2,296 pounds per sample provided reasonably accurate data for analysis of the gold distribution. These studies indicated that the bulk of the gold is within 40 feet of bedrock in stacked, lenticular zones of cemented gravel that are largely confined to the relatively narrow, meandering course of the deepest portion of the bedrock channel. Drilling studies involved the testing of truck-mounted rotary, buckett and vibratory drills, none of which proved to be a completely versatile tool for sampling quickly and reliably both consolidated and unconsolidated gravel..

Jan 1, 1974

By R. S. Dean

"Interest in the nitrogen content of steel has increased sharply in the last few years. Investigations have indicated that its presence in steel has an important bearing on high temperature brittleness3, magnetic properties4, room temperature hardening5, and shock resistance. The steel producer may therefore look forward with certaintly to the necessity of controlling this element in a considerable proportion of his product. The literature, however, reveals a great many contradictory statements concerning the percentage of nitrogen which must be present to produce given effects on the properties of iron and steel. Most of these arise from a misunderstanding of the nature of the iron-nitrogen diagram near the iron end and a lack of recognition of the effect of state of aggregation on physical properties although both have been fairly well worked out.My thanks are due to Mr. J. L. Gregg, Prof. R. H. Dowdell, Mr, R. F. Mehl and Mr. H. C. Vacher for suggestions in connection with the preparation of this paper, and to Mr. C. H. Hefty and Mr. G. T. Motok for furnishing a valuable bibliography and translations of articles by Must and Duhr.The iron-nitrogen diagram in the solid state, so far as it concerns the nitrogen content of commercial iron and steel, consists simply in a solubility curve increasing with temperature. The important thing about this solubility curve is that without cold wore the iron nitride when precipitated does not go into solution on heating for long periods below 300°C. This slowness of solution is probably due to the fact that iron nitride when present as a separate phase has at these temperatures an equilibrium pressure of several thousand atmospheres7 and that therefore each particle of iron nitride surrounds itself with a layer of nitrogen. The precipitation of such an unstable crystal presents points of interest thermodynamically but we can not go into these here. It is quite well established that it precipitate. It can not diffuse then unless this layer is broken through or the temperature and pressure are increased to a point where the nitrogen is absorbed at an appreciable rate in the surrounding iron. This rate will depend on the degree of unsaturation of the iron and the excess pressure of the nitrogen above equilibrium pressure. The degree of unsaturation is determined by the temperature alone so that the temperature at which the rate of solution of the nitride becomes appreciable will depend on the pressure of nitrogen developed. This, in turn, will depend on the balance between rate of decomposition of the nitride and the rate o: flow of the iron. In annealed iron, this temperature of appreciable solution rate is between 300 and 350°C.8 By cold work, however, the elastic limit of the iron is increased, and conditions for the nitride to go into solution are reached at a much lower temperature, giving rise to the so-called blue brittleness. This brittleness and hardening is due to iron nitride going into solid solution and is not precipitation hardening."

Mar 1, 1931

By George L. Gates

[When clays e.re mixe~ "Jith "~later to nake mud fluids f'ol' use in :irilling ','Iells "for oil and gar: h;:r vue :;'0 tary me thee. t 18 liquid mij~ tUl"es have certair.. phypicr..l characteri.",t.ics that vary ",dth t e Qlldlltit.y find]

Jan 1, 1941