Search Documents

By W. D. Kaiser

Recent legislation and expected future legislation is aimed at reducing the dust levels developed in underground coal mines. Several techniques for reducing dust levels are being evaluated. One of these is the modification of cutting parameters such as feed rates, cutting speeds, and pick configurations in order to reduce the amount of dust generated. In order to evaluate the feasibility of modifying cutting parameters to reduce dust, the Bureau of Mines commissioned Battelle to construct a small scale mining machine which could be used for evaluating the effects of those changes in cutting parameters. Specific features of this machine were that it should be highly instrumented to measure various cutting parameters, should have a wide range of feed and speed controls, and it should be possible to vary the pick configurations and geometries on the machine. In addition, it was desired that this machine should have cutting capabilities which greatly exceed present coal mining practice and also that the unit should be small enough and portable enough that it could be taken into and out of operating coal mines with a minimum of interference with the normal coal mine operations. The first step in constructing a machine to meet these requirements was to determine the cutting forces and approximate sizes of components which would be required to cut at the speeds and feeds specified by the Bureau of Mines. Initial calculations using; published data on cutting forces indicated that cutting forces in the neighborhood of 5,000 lbs and power levels of approximately 30 horsepower would be adequate for the application. However, further data developed during the course of the project indicated that when low efficiency picks are used, cutting forces and powers can be two to three times as high as these initially estimated values. After several design iterations, a design was chosen in which the cutting head was driven by four hydraulic motors which were part of a hydrostatic transmission which, in turn,

Jan 1, 1973

By Wing G. Agnew, John A. Johnson

"INTRODUCTION This paper is one of a series being published by the Bureau of Mines pertaining to an investigation on the use of stemming in metal mines now being conducted at the Mount Weather Testing Adit. Its purpose is to compare the amount of dust and gases produced as a result of blasting charges of dynamite (1) in drill holes, (2) in bombs, and (3) in mud-cap or adobe shots.ACKNOWLEDGMENTSValuable assistance and advice on stemming were given by members of the staff at the Bureau of Mines, as acknowledged in previous publications. 4/TEST PROCEDUREThe results used for comparison in this report are from dust and gas samples taken after blasting (1) four regular test rounds with no stemming, (2) five bomb shots, and (3) two mud-cap or adobe shots.The four rounds were the standard 26-hole test rounds designed to break 4 feet of rock. The procedure for drilling and blasting these rounds is described in Report of Investigations 3509.Before the regular test rounds were blasted, about 1,200 bounds of fine rock was placed on the steel mucking sheets that covered the end of the adit track; the wails, hack, and floor of the adit were washed thoroughly; and the fine rock on the mucking sheets was completely wetted.Each of the 5 bomb shots consisted of 10 sticks of dynamite tied together and hung at midpoint of the adit, 8 feet from the fall."

Dec 1, 1942

By M. D. Balen

The U. S. Bureau of Mines has undertaken the development of mineral industry cost escalation factors to enable the estimation of mineral development and extraction costs for mineralized sites in Alaska throught the use of the Bureau's Cost Estimating System v2.0 (CES 2.0). For the purposes of this document, all calculations are based on, and reflect the economic environment in Alaska in July 1992. The greater cost of mining in Alaska as compared to the contiguous-48 States can be estimated for Alaskan mining operations through (1 ) the analysis of capital and operating costs for analogous mine and mill plants in operation in the contiguous-48 States; (2) the hypothetical relocation of mine and mill plants from their actual location(s) to Alaska by making engineering modifications to the mine and mill plant design as required by the Alaskan site characteristics; (3) calculation of the cost of the required engineering modifications and; (4) the escalation of all costs to a level representative of the economic environment in Alaska at some specific point in time.

Jan 1, 2011

By D. P. Lindroth

The thermal diffusivity above 298 K, up to 400 K and at pressures from ambient down to 10-10 torr was measured for the following six igneous rock types: tholeiitic basalt, obsidian, rhyolite, granodiorite, gabbro, and dunite. The thermal diffusivity data were obtained by the laser flash method. Extreme values range from a low of 5.3X10-3 cmF/sec for rhyolite at 383 K and 2X10-7 torr to a high of 13.4x10-3 crrf/sec for dunite at 298 K and 760 torr. Data are also included on a commercial fused silica, which was used as a standard.

Jan 1, 1974

By Anderson Dana

THIS PAPER describing methods and costs of mining and preparing gravel and sand for market at the Port Jefferson plant of the Seaboard Sand and Gravel Corporation, is one of a series of articles on gravel and sand mining, prepared for and published by the U. S. Bureau of Mines, which is designed to disseminate technical information regarding the methods used. The cost tabulations represent operating expenditures only and not total costs, It is recognized that publication of total costs might in many instances cause embarrassment to individual producers, as well as to the industry as a whole. On the other hand, operating costs are essential to the technical [ ]

Jan 1, 1932

By Philip Thompson

The Bureau of Mines investigated a selective flocculation-flotation technique to remove insoluble slimes from low-grade potash ore in a continous 45-kilogram-per-hour (100-pound-per-hour) process investigation unit (PIU). This research is part of the Bureau's program to improve resource recovery from low-grade ores. Results showed that 84 percent of the insoluble slimes were removed from an ore containing 5.5 percent water-insolubles and 14 percent K20 using a Bureau-developed, cationic flocculant-glycol ester-diesel oil reagent. Subsequent potash flotation recovered 75 percent of the potash in a cleaner concentrate assaying 56 percent K20. Concentrate leaching upgraded the product to market specifications of 60 percent K2O. An economic evaluation by the Bureau suggested that the rate of return on investment, after taxes, should be about 20 percent for such an enterprise.

Jan 1, 1980

By J. Walden, J. Rhoades, R. E. Miller, R. Gibbs, P. Boman

Accelerometers and pressure transducers, mounted in suspension components, can be used to monitor the ride of haulage trucks. Presently, it is difficult to tell what caused a jolt to the truck using either pressure or acceleration data alone. When information from a global positioning system (GPS) is recorded at the same time as shock pressures or acceleration data, the exact location of an event can be determined. Mine management can then determine what caused the jolt to the truck. This research is part of a National Institute for Occupational Safety and Health (NIOSH) project called "Engineering controls for reduction of jolting/jarring injuries in surface mines." NIOSH is investigating how the work environment of haulage truck drivers can be improved. The US Mine Safety and Health Administration (MSHA) notes that, between 1986 and 1995, 60% of the back injuries were to haulage truck drivers in metal/nonmetal surface mining. Personnel from Phelps Dodge suggested that combining acceleration data with information obtained from a GPS could generate results with a variety of uses. Therefore, researchers at the Spokane Research Laboratory (SRL) began investigating how to tie acceleration and GPS data together. It was originally thought that this tool would be used primarily for road and truck maintenance. However, as research progressed, it became apparent that it would also be useful in providing feedback about equipment operations and identifying unusual causes of jolting. Experimental approach Available components that function well by themselves were linked for the purpose of proof of concept. Using a Modular Mining Systems (MMS) product called Vital Signs, SRL researchers took an Aero-Marine Products (AMP) acceleration recorder and hardwired it to MMS Dispatch equipment already installed on a truck. AMP is one of several manufacturers of acceleration recorders frequently used to monitor freight during shipping. MMS Dispatch is used for production accounting and truck dispatching and uses GPS tracking. Through Vital Signs, an analog or digital alarm signal can be recorded. Steve Rhoades, of MMS, wrote unique code that links the Vitals Signs data and GPS location and stores this data in an ASCII log file. SRL researchers installed the equipment in a Caterpillar 793 haul truck. The result was a working prototype. Figures 1 and 2 show the instrument installation in the truck. Discussion From 8:30 pm on Sept. 14, 1998 until 6:50 am on Sept. 15 1998, 899 jolts above a threshold of 2 g (1 g is the acceleration of gravity. It is either 9.81 m/s2 or 32.17 ft/ s2.) were measured on the test truck. Some sections of the haulage road produced most of the events, while

By Robert L. Lagace

A whole-mine experiment to assess the practical feasibility and utility of the dedicated-wire technique for overcoming poor trolley carrier phone system performance at a large underground coal mine was designed, performed, and evaluated. The technique involves the use of a single, low-loss, properly terminated and branched auxiliary wire placed in the rail haulageway. This auxiliary dedicated wire allows signals to electromagnetically couple to the trolley wire/rail transmission line, and thereby significantly decrease the overall signal attenuation rate on the trolley wire/rail line. The in-mine dedicated-wire demonstration program and its results, conclusions, and recommendations are described. The dedicated-wire technique is shown to be a valid and practical one for significantly improving carrier phone system performance in coal mines.

Jan 1, 1981

By Shail J. Butani

In 1986 the Bureau of Mines conducted a probability sample survey, Mining Industry Population Survey, to measure such employee characteristics as occupation; principal equipment operated; work location at the mine; present job, present company, and total mining experience; job-related training during the last 2 years; age; sex; race; and education. The population estimates are necessary to properly analyze the Mine Safety and Health Administration (MSHA) injury (includes illness and fatality data) statistics; that is, to compare and contrast injury rates for various subpopulations in order to identify those groups that are exhibiting higher than average injury rates. This report uses the survey's results to characterize the U.S. stone mining workforce from March through September 1986. Similar reports have been published for the metallic, sand and gravel, and nonmetallic mining industries, as well as for the entire metal and nonmetal mining (includes metallic, stone, sand and gravel, and nonmetallic industries) sector and the coal mining sector.

Jan 1, 1988

By H. L. Riley

Cleaning and handling of fine coal are generally conceded to be more difficult problems than preparation of the coarser sizes. Increased mechanization in the coal-mining industry has, in general, resulted in an increased percentage of the fine sizes in the total coal mined. If the coal fines are cleaned by wet methods, the minus-1/16-inch square-mesh particles cause most of the sludge and slurry problems encountered in preparing wet coal. Equipment that separates coal from refuse on the basis of specific gravity is not efficient on sizes that, because of their fineness, do not follow the same laws of hindered settling as the larger particles. Probably the best solution of fine-coal cleaning problems is to use other methods, such as flotation, that utilize other physical characteristics than those determining hindered-settling ratios. Regarding the type of flotation known as the Elmore vacuum-flotation process there has been a scarcity of data and information available in this country. An investigation has therefore been made to obtain additional date and information on this process under laboratory conditions. During this investigation an effort has been made to evaluate the relative efficiencies of vacuum and mechanical laboratory froth flotation cells. The investigation included float-and-sink, screen-sizing, and flotation tests on 2 different samples of 14-mesh to 0 raw coal and an a sample of slurry from the settling-tank overflow of a typical washer. One raw-coal sample was obtained from the American bed and represented a type of coal that is relatively easy to clean. The other raw-coal sample was from the Mary lee bed and represented a type considered difficult to clean.

Jan 1, 1954

By M. P. Ristenbatt

A new automated post-disaster signaling system, intended to use through-the-earth EM propagation, was demonstrated in the laboratory at an input SNR of -34 dB. The system presently available requires an input SNR of +6 dB, and uses a human-ear detector. The work here demonstrated coherent integration, for the automated system, in multiples of 17 s, up to 1088 s (18 minutes). A repeating pseudorandom (or pseudonoise) signal is used, which offers an ideal auto-correlation at the receiver matched-filter output. A novel decision-variable algorithm achieves the estimate of noise level by using those matched-filter output samples that occur between the signal auto-correlation peaks. This work included corraboration that the received signal power decreases as distance to the tenth power, for through-the-earth propagation. Thus, the above 40 dB reduction in required input SNR permits an automated system to have a range 2.5 times that of the present system. In addition, an automated system permits the possibility of operating receivers around-the-clock; this would reduce the initial-detection-time from a few hours (present system deployment time) to a few minutes (signal processing time).

Jan 1, 1981

By W. K. Connor, O&apos

The U.S. Bureau of Mines investigated the Sheep Creek prospect in the north-central Alaska Range to evaluate the Pb, Zn, Ag, and Sn resources. The studies included field investigations, mineralogical characterization, and concentration tests. Mineralization at Sheep Creek consists of disseminated, banded, and massive pyrite, sphalerite, and galena. Tin occurs as grains of cassiterite (Sn02) in the quartz-mica matrix and within pyrite and sphalerite grains, and Ag occurs in solid solution within the galena. Three bulk surface samples and two sets of core samples were collected at the Sheep Creek prospect for this study. Gravity concentration yielded products with up to 30 pct Sn, and the best result was a product that recovered 52 pct of the Sn at a grade of 22 pct Sn. Bulk sulfide flotation yielded products that recovered up to 89 pct of the Zn, 73 pct of the Pb, and 75 pct of the Ag, but grades were relatively low; selective flotation would significantly increase the grades.

Jan 1, 1989

By Robert W. Van Dolah

On December 27, 1961, a fire and explosion destroyed the blasting agent mixing plant and an attached storage barn of the Whitaker-Atlas Supply Co., near Norton, Wise County, Va. Five residences, an office building, four trucks, and three automobiles were completely destroyed; a house trailer and several other trucks and automobiles were severely damaged; and other property damage, including much window breakage, occurred up to 3 miles or more airline distance away. Through the quick action of the fire marshal of the Norton Fire Department, Norton, Va., there were no fatalities and only five persons required hospitalization. This incident is of particular interest because of the widespread practice of mixing fuel oil (FO) with ammonium nitrate (AN) to prepare low-cost blasting agents, in many cases under conditions and circumstances not very different from those presented here. A representative of the Bureau of Mines Explosives Research Laboratory, Pittsburgh, Pa., and field representatives of the Bureau's Health and Safety Activities conducted the investigation. Information in this report was obtained from representatives of the Whitaker-Atlas Supply Co., the Norton fire marshal, and others who were on the scene either shortly before or after the incident occurred. Representatives of the Manufacturing Chemists' Association, the Institute of Makers of Explosives, and individual ammonium nitrate producers participated in the inquiries and investigations.

Jan 1, 1962

By Charles T. Baroch

RESEARCH strengthened the position of cesium as the preferred material (commonly but erroneously called "fuel") for ionic propulsion engines. Its use as an element of the plasma thermocouple for generating electricity also seemed more likely. Domestic Production.-No domestic ore of cesium and rubidium was produced. San Antonio Chemicals, Inc., San Antonio, Tex., and Maywood Chemical Works, Maywood, N.J., continued to produce cesium and rubidium compounds including carbonate, chromate, hydroxide, nitrate, sulfate, and all four halides. Rocky Mountain Research, Inc., Denver, Colo., began producing various cesium and rubidium salts. American Potash & Chemical Corp., Los Angeles, Calif., offered cesium and rubidium for sale.

Jan 1, 1960

By C. D. Messelt

The Bureau of Mines investigated the application of a diffusion model to sintering rate data developed for lithium titanium ferrite. The data were obtained by sintering pressed pellets under identical conditions for various times up to 11 hours. Stereological measurements were made on polished sections, and sintering rates were calculated. A model for intermediate stage sintering was fitted to the stereological data. This procedure produced a method by which these type data could be used to study the relative importance of volume and grain-boundary diffusion under a variety of sintering conditions.

Jan 1, 1979

By L. J. Kane

Conventional methods for determining the size of dust suspended in a gas require that agglomerates (clusters of particles) first be broken into particles, but in evaluating industrial dust-removing equipment the size of the agglomerates as they actually exist in the gas stream is far more important. This paper presents results of an investigation by the Federal Bureau of Mines to develop methods for determining the size of dust agglomerates suspended in a gas stream. The studies are part of the Bureau's continuing research on synthetic liquid fuels. The size and size-distribution of agglomerates as they exist when the gas reaches the filter was determined by using a membrane filter in conjunction with a dust count under a microscope. A membrane filter is a cellulosic sheet about 150 microns thick containing millions of holes per square centimeter--holes of uniform diameter that run directly through the sheet without interconnection.

Jan 1, 1960

VOLUME II Volume II, in conjunction with Volume I, is a general guide to the selection of cost-effective methods of site data acquisition in all geologic environmental, and socio-political circumstances. The judgement of a generalist or trained specialist must be relied upon in the final analysis to design the optimum program for a specific site.

Jan 1, 1976

By Annie G. Smelley

The Bureau of Mines is testing a dewatering technique for phosphatic clay waste that will recover a portion of the water lost using conventional waste disposal methods and produce solids suitable for land reclamation. The technique utilizes a flocculant, polyethylene oxide (PEO), that forms strong, stable flocs that can be dewatered on a static screen followed by further dewatering on a rotary screen. In field tests conducted in northern Florida, clay wastes containing a nominal 2.5 pct solids have been consolidated to greater than 20 pct solids. The rate at which PEO-treated material continues to dewater in a mine cut also was monitored. Preliminary results indicate that PEO--treated material will dewater to 30 pct solids in 140 days. Pretreatment of phosphatic clay waste with lime and H202 was shown to improve the dewatering technique for problem clay wastes.

Jan 1, 1985

By J. F. McIlwain

The Bureau of Mines has investigated fumes generated by selected welding electrodes used in mines in order to help determine their relative health hazard potential. Fumes were generated and collected in an enclosed chamber for subsequent generation rate and chemical constituent determination. Shielded metal arc electrodes from the following groups were tested: AWS types E308-16 and E310-16 stainless steel, ECoCr-A Co-Cr hardfacing alloy, ENiCr Ni, an Mn-Cr buildup alloy, E7018 carbon steel, and EII018-M low-alloy steel. Flux-cored wire electrodes of this last group also were tested. Fume generation rates and the chemical composition of the fumes were measured. From these data, exposure in-dices were determined, which give a relative measure of the health hazard potential of using the electrodes. The effect of welding onto build-up alloy layers on the fume composition also was examined for five of the higher alloy groups.

Jan 1, 1987

By John H. Soulé

This paper describes the location and general features of the ?Red Bed? or sandstone copper deposits in southeastern Colorado and New Mexico. Most of the areas containing this type of deposit were visited, and many deposits were examined. Some deposits were not visited because of lack of information as to their location. In the large area covered a great variety of climatic, geographic, and topographic conditions exists. Some of the deposits are in arid areas, whereas others are in heavily forested regions. Altitudes range from 3,400 to 9,200 feet, and the terrain varies from flat plains to rugged mountains. Transportation is a difficult problem in most of the districts, involving long truck hauls to a railroad and long rail hauls to a smelter.

Jan 1, 1956