Search Documents

By N. M. Safaya

Moderate to acute deficiency of plant available phosphorus is very common in western coal mine spoils and topsoils. Although some of the spoils are known to contain seemingly adequate amounts of total phosphorus, the plant available phosphorus is so low that it constitutes a serious plant growth limiting factor in the mined lands. For the revegetation of these spoils, the use of species, varieties and ecotypes exhibiting greater efficiency for P uptake and utilization, or conversely, lesser susceptibility to P deficiency would be highly desirable. To identify such plants, quick and adequate methods of screening germplasm should he available. In the present growth chamber study several plant species were screened using continuous flow culture and spoil culture systems to provide information on their relative susceptibility. In flow cultures, P was maintained at 0.25, 2.5, and 25 moles; while in spoil cultures it was applied at 0, 25, and 75µg/g to a P-deficient spoil. Phosphorus deficiency symptoms appeared in alfalfa cultivars, birdsfoot trefoil, emerald crownvetch and yellow sweetclover within 7-10 days upon transfer of their seedlings to U.25 or 2.5 µM P solutions. Burning bush and Russian thistle, found abundantly as pioneering species on mine spoils, showed no deficiency symptoms; their shoot dry matter yield in the 0.25µM P treatment was 24% and 36%, respectively of their maximum yield obtained with 25 µM P. However, the percent increase in the dry matter yield of legumes with 0.25 µM P ranged from 7-13% over their maximum yield. With the increase in solution P concentration, the root dry weight ratio in the legumes increased from an average of 0.22 to 0.43, while in the weeds from 0.14 to 0.30. The low susceptibility of Russian thistle to P deficiency was also demonstrated in the spoil culture experiment. Legumes showed greater response to P-fertilization on the spoil than did the two weeds. With increasing concentrations of P in the solution, the root weight ratio of all the species decreased. At 25 µM P, weeds invested only 14% of their total dry matter yield in the root fraction, where as legumes and grasses invested as much as 24% and 33% respectively. Weedy species averaged higher P concentrations than the legumes and grasses. The mean P concentrations of alfalfa cultivars were the lowest among legumes. In general, P concentrations increased with the increase in P supply. In the flow culture system, P supply increased the Ca levels of legumes. The mean Mn concentrations were highest in the weedy species. The increases in P supply decreased Zn levels in all of the species. File effects of P fertilization on the tissue concentrations of Mn and Zn in spoil culture were similar to that of flow culture system. From this preliminary study, it may be concluded that the continuous flow culture system is efficient in rapid screening of a large number of species under controlled conditions for their efficiency in adapting to mineral stresses.

Jan 1, 1982

By Ronald Branstetter

Gaseous and particulate exhaust emissions from 20 diesel engines in service at five underground mines were measured with high accuracy instrumentation. The engines that were tested were checked for faults or maladjustments. The vehicle and engine maintenance organization was studied at each mine and an idealized maintenance program was devised. Faults were induced in a new diesel engine to determine their effect on the characteristics of the exhaust emissions. The results, conclusions and recommendations from this investigation are presented in this final report.

Jan 1, 1983

Quickly and cheaply consolidate underground slimes to facilitate their use as backfill and permit their easy handling for other reasons. Approach: The slurry containing slimes is pumped into active stopes and electrokinetically dewatered to provide consolidated back fill. How It Works: To densify slimes electro-kinetically two electrodes are placed in the material to be dewatered and densified. Typically, the electrodes are pieces of wire mesh fencing. One is placed on the bottom, and the other is suspended in the slurry near the surface. Figure 1 is a simplified section of a test. A d-c voltage of 100 to 400 volts is applied across the slurry. This causes the solid particles which are in suspension in the water (usually these are negatively charged) to migrate toward the anode; simultaneously, the water moves toward the cathode. Water immediately adjacent to the negatively charged solid particle surfaces contains an excess of dissolved positive ions. When these ions are attracted to the electrode and move towards it, they also exert

Jan 1, 1976

By Stephen C. Tadolini, Thomas M. Barczak

A critical safety component for all underground mining is intrinsic and standing support systems. Specifically, tabular hardrock mining exploits a wide variety of deposits that require various methodologies to safely mine the ore material. Several new support systems have been developed in recent years for hard rock applications which have been modified or applied in a variety of ground control applications. These include prestressing devices, improved cribs, and free standing supports. Various standing support and prop-type systems have been designed for hardrock applications with seismic loading conditions to accept prestressing. The prestressing, using water-filled cells, creates an active load upon installation and is considered essential to maintain support during and after the blasting of the mine faces. Heavy seismic activity is also present in these mines and the prestressing units can provide some energy absorption capability to help preserve the integrity of the support. This paper presents an overview of these innovations in support technology.

A mobile vacuum sweeper to remove loose coal and coal dust from underground coal mine workings was designed, built, tested, and evaluated. The design was based on an extensive test program. Pick up and conveying rates vs. air volumes, velocities, and nozzle shapes were determined for coal rubble in a laboratory pneumatic handling system. A gas/solids separation system was developed and tested in the laboratory capable of separating the solids loading from the vacuum system air stream to the very high degree required to preclude degradation of the ambient (mine) air. Two designs were made, one for belt conveyor and one for general district cleanup. The belt cleanup machine was chosen for test and demonstrated in an underground coal mine performing cleanup work in belt haulageways and on ribs.

Jan 1, 1975

By H. A. Wright

This report assesses the economic, legal, institutional and technical factors that affect the current and future status of implementation of mine monitoring systems in the United States. It begins with a description of a poll of the Mining Production Research Committee and the Mine Monitoring and Communications Committee of Bituminous Coal Research that was conducted to establish industry monitoring needs and constraints. Existing systems in the United States and foreign countries are then reviewed and compared with the requirements set forth by the industry committees. At the same time, state and federal mining laws are reviewed, and equipment currently available from suppliers of mine monitoring systems and components is discussed. A framework for cost/benefit analysis is established and a series of case examples for various monitoring functions are presented. The total values of the market for mine monitoring systems in 1980 and 1990 are estimated on the basis of industry statistics and system cost estimates.

Jan 1, 1982

By William H. Schiffbauer

The Bureau of Mines has developed a passive encoder for range knobs, a device that automates the task of obtaining the range settings from devices or instruments to be input to microcomputers. It is easily constructed and installed and will not disrupt the device to which it is being attached. It consists of a custom knob and a small printed circuit board that has light-emitting diodes and magnetic reed switches attached. A ribbon cable connects it to a microcomputer. This encoder eliminates one source of human error in an automated process.

Jan 1, 1983

By L. B. Berger

From time to time the Bureau of Mines receives requests for information and advice regarding the safety of using internal-combustion engines operated on butane fuel as prime movers for haulage and other purposes in mining and tunneling. The purpose of this, circular is to discuss the properties of butane and to present data in regard to the possible use of this fuel in underground operations. Published information on the use of commercial butane as a fuel for internal-combustion engines indicates that, insofar as performance is concerned, butane may be utilized satisfactorily and efficiently for this purpose. However, the introduction of a volatile, inflammable material such as butane into confined spares such as mines or tunnels would create potential fire and explosion hazards that should be given due consideration by those concerned with the promotion of safe practices.

Jan 1, 1944

By Richard E. Thill

Elastic wave velocities and moduli were determined by both the pulse and resonance methods in a large number of specimens of St. Cloud Gray Granodiorite and Tennessee marble under the same moisture, temperature, and stress environment. Long cylinders were first tested by the resonance method to obtain longitudinal bar and torsional wave velocity. The cylinders were then sectioned in half and tested by the pulse method to obtain the transient pulse velocity. These velocities were later used to obtain various moduli for comparison. Statistical comparisons between the Young's, shear, and bulk moduli and Poisson's ratios obtained independently by the pulse and resonance methods indicate that the methods do not give equivalent results in nearly isotropic rock. The amount of difference varies for each modulus, with the least difference (less than 5 pct) occurring in the shear modulus and the greatest difference (as high as 34 pct) in the bulk modulus. Moduli determinations in aluminum show much closer agreement between the pulse and resonance methods than in rock. The discrepancy in pulse and resonance results probably is caused by frequency dispersion effects and by differences in error sensitivity in the various formulas used to calculate the moduli.

Jan 1, 1974

By E. Concha

The concept of an Automated Continuous Explosive Excavation system (ACEE) for the underground mining applications of development drifting and room and pillar mining has been evaluated in comparison with conventional drill, blast and muck operations. The role and possible extent of application as this method was identified. The evaluation examined each element of existing and of proposed ACEE design concepts in a defined mine environment. Step by step procedures were developed to quantify the evaluation process where this appeared feasible. One conclusion drawn was that a system approach to ACEE design is not only feasible but attainable within the state of the art. Several preliminary design concepts were formulated and examined in order to determine what further research or development might be needed to realize them.

Jan 1, 1982

By Oliver C. Fursman

These investigations were conducted to determine conditions for recovery of nickel and copper from Funter Bay, Alaska, sulfide ore and recovery of nickel from nickel-silicate ore, Nickel Mountain, Riddle, Oreg. Samples of Funter Bay cupriferous and nickeliferous pyrrhotite ore, were treated by beneficiation, roasting, electric smelting of roasted are for matte production, chlorination, leaching, and sulfatizing roasting with subsequent leaching. Funter Bay and Nickel Mountain ores were smelted together to produce matte. Total sulfide flotation, followed by magnetic separation of the tailings to recover entrained nickel-bearing pyrrhotite, resulted in the highest nickel recovery in beneficiation tests on Funter Bay are. Overall beneficiation resulted in recovery of 98.5 percent of the copper and 95.4 percent of the nickel in the concentrate that contained 3.5 percent copper and 1.7 percent nickel.

Jan 1, 1962

By Leslie S. Rubin

A ventilated helical boost pump was developed that can handle varying flow rates and/or solids concentrations while operating at a single rotational speed and without computer assisted feedback controls. The boost pump developed and briefly tested during this program was designed to accomodate flows suitable for a 3-in. diameter pipeline. The boost pump's ventilated design provides the automatic pressure regulation needed to meet the system's requirements for supporting transient pipeline flow.

Jan 1, 1984

By D. Harrington

The code of hoisting signals for use in mines hoisting from one level, as suggested in this publication, is submitted to induce consideration of this subject by representative groups of the coal-mining industry, such as the lithe Inspectors Institute of America, National Coal Association, American Mining Congress, and others, as well as to -furnish a code of signals for use in those mines operated in States that do not have regulatory hoisting codes in their mining laws, or regulations. The signal codes described in this publication apply only to mines hoisting from one level and to slope mines. Mines that hoist from more than one level are referred to Bureau of Mines Information Circular 7289 Suggested Hoisting-Signal Code For Metal Mine Shafts, which suggests signals for hoisting from various levels or stations.

Jan 1, 1944

By Robert G. Lundquist

The Bureau of Mines compared longitudinal strain energy output of a percussive drill to energy determined by measuring maximum piston velocity. Strain gages were used to determine the strain-time waveform and its amplitude at seven levels of operating pressure and eight levels of thrust. The longitudinal strain energy was found to be approximately 14 ft lb less than the maximum piston energy at comparable operating conditions.

Jan 1, 1969

By George A. Savanick

The objective of this research is to develop a method for measuring the tensile strength at the interface between minerals in rock. These measurements reflect the strength of the attractive forces operating at crystalline interfaces in rock. Since these forces act in opposition to the forces set up in various rock fragmentation processes, measuring their strength may help in designing more efficient methods of rock fragmentation. The method developed for measuring the strength of intergranular adhesion in rock involves separating a bicrystal from the rock and determining the tensile strength at its solid-solid interface. This technique has been successfully applied to the study of quartz-feldspar interfaces separated from massive pegmatites, graphic granite, and the Rockville granite, yielding average tensile strengths of 5.86, 8.62, and 10.65 meganewtons per meter squared (MN/m2) (850, 1,250, and 1,524 psi, respectively). The data this technique provides indicate that the members of these bicrystals are strongly adherent. Examirtation of bicrystals broken at the crystalline interfaces indicates that the bonds responsible for this adhesion operate over only a portion of the interfacial area. This work conclusively demonstrates that tensile strength tests can be conducted on small selected areas; for example, grain boundaries in rock. The small-scale zones of strength or weakness determined in this way can be related to the overall strength of the rock.

Jan 1, 1972

By W. M. Dressel

In producing feed for a lead blast furnace, concentrates analyzing 70 to 80 pct Pb are sintered to produce a physically acceptable low-sulfur product which contains only about 50 pct Pb. Mixtures of PbS with varying amounts of SiO2, CaO, Fe 20., and ZnS were heated in an oxidizing atmosphere at 1,000° C; the products were cooled and examined to determine the problems involved in producing sinter with substantially higher lead levels. Microscopic and electron microprobe studies of the above products as well as experimental and commercial sinters indicate that sinters consist essentially of lead silicates, lead-zinc silicate, calcium zinc silicate, and spinel (ferrite). Lead oxide and lead sulfate areas appear to result from insufficient mixing of the materials prior to sintering. The data give an insight into the process and show that sintering results from a complex interaction of all constituents and that sintering is not simply a matter of diluting the mixture to control the oxidation of lead sulfide.

Jan 1, 1975

By E. G. Davis

As a result of interest by the U.S. Department of Energy, the Bureau of Mines conducted studies on comminution of bituminous coal to the 2-um particle size range using the Bureau-developed turbomill. Both "plant grind" size (80 pct minus 75 um) and microsize (minus 10 um) coal can be produced in a single step with the Bureau's turbomill. In 15 min, minus 2.4-mm coal milled in water with steel shot was reduced tc 65 pct minus 75 m and 26 pct minus 2 m, with an energy requirement of 139 kW^h/mt coal. Plant-grind size coal milled in water, with Ottawa sand as the milling medium, was reduced to more than 45 pct minus 2 m in 15 min, at 175 kW?h/mt. Plant-grind coal milled with steel shot was reduced to 57 pct minus 2 um in 15 min, at 138 kW?h/mt. When diesel fuel was substituted for water, the milling of the coal was less effective and less energy efficient. Keeping the pulp dispersed was critical. Without an effective dispersant, the slurry became very viscous with increased milling time, resulting in higher energy requirements, low heat dissipation, and poor grinding efficiency.

Jan 1, 1987

By Gerrit V. R. Goodman

A laboratory study assessed the impacts of water spray pressure, face ventilation quantity, and line brattice setback distance on respirable dust and SF6 tracer gas concentrations around a continuous mining machine using a sprayfan or directional spray system. Dust levels were measured at locations representing the mining machine operator and the standard and off-standard shuttle car operators, and in the return airway. The results showed that changes in all three independent variables significantly affected log-transformed dust levels at the three operator sampling locations. Changes in setback distance impacted return airway dust levels. Laboratory testing also identified numerous variable interactions affecting dust levels. Tracer gas levels were measured on the left and right sides of the cutting drum and in the return. Untransformed gas levels around the cutting drum were significantly affected by changes in water pressure, face ventilation quantity, and setback distance. Only a few interactions were identified that significantly affected these concentrations. Gas levels in the return airway were grouped by face ventilation quantity. Return gas levels measured at the low curtain quantity were generally unaffected by changes in water pressure or curtain setback distance. At the high curtain quantity, return airway gas levels were affected by curtain setback distance. A field study was conducted to assess the impact of these parameters in an actual mining operation. These data showed that respirable dust levels may have been impacted by a change in water pressure and, to a lesser extent, by an increase in curtain setback distance. A series of tracer gas pulse tests were also conducted during this study. The results showed that effectiveness of the face ventilation was impacted by changes in curtain flow quantity and setback distance. Laboratory testing supported similar conclusions.

Jan 1, 2004

By William O. Vanderburg

The fluorescence of many minerals, when excited by different wave lengths, of ultraviolet radiation, has long been recognized as a spectacular laboratory phenomenon. Since the original display in the British Museum, the phenomenon has been used frequently for educational purposes and public demonstrations. Its practical application for the rapid detection of certain minerals in ores and mill products at the zinc mine at Franklin, N. J., has been described.3 Due to technical improvements in ultraviolet-radiation apparatus, fluorescence has found a new field of application in the tungsten-minim; industry. Although fluorescence of scheelite (calcium tungstate) has been known for a number of years, the practical application of the phenomenon is the outgrowth of a program of cooperative research conducted by Ott F. Heizer, manager of the Nevada-Massachusetts Co., Inc. , Mill City, Nev., and Dr. Paul F. Kerr of Columbia University. Special portable lights for fluorescing scheelite have been developed and utilized in underground geological work. Thanks are due Ott F. Heizer for permission to publish data included in this paper.

Jan 1, 1935

By Duane L. Abata

Toxic gases produced by the detonation of six explosives were measured in an underground hardrock metal mine during actual mining operations. The six explosives included two semi-gelatin dynamites, three slurry explosives and an ammonium-nitrate, fuel-oil/ammonia dynamite combination. Explosives were detonated at the face of a drift and the toxic gases produced by the detonation were trapped to the end of the drift by a bulkhead located a short distance away from the face. Toxic gas concentrations were then measured with direct readout instruments and together with the containment volume, the toxic gas volumes per mass of explosive were calculated. Toxic gas measurements were found in the following ranges (ft3/lbm): N02 0.010-0.035; N02, 0.003-0.019; CO, 0.08-0.30; S02, 0.00-0.05; and C02, 0.7-1.8. Results showed that toxic gas production (ft3/lbm) correlated with the densities (kg/m3) and energy densities (kJ/kg) of the explosives tested.

Jan 1, 1978