Search Documents

By Chris Ringas

The safe operation of gas transmission pipelines is increasingly coming under the spotlight. Increasing environmental pressure is also forcing pipeline owners and operators to ensure the integrity of their pipelines. The integrity of a pipeline is usually determined using intelligent pigging, often referred to as In Line Inspection (ILI). However, in many cases, gas pipelines cannot be pigged for a variety of reasons. The National Association of Corrosion Engineers (NACE) has recently published Recommended Practice (RP) 0502, referred to as the External Corrosion Direct Assessment (ECDA) Methodology to assist pipeline owners with assessing the condition of pipelines that cannot be pigged. 2. External Corrosion Direct Assessment - NACE RP 0502 The ECDA Methodology is conducted in four phases as follows: ? Pre-Assessment ? Indirect Inspection ? Direct Examination ? Post-Assessment In the Pre-Assessment Phase, all the relevant historical and current data relating to the pipeline in question is reviewed. This covers pipeline, construction, soils/environmental, corrosion control and operational data. The aim of the Pre-Assessment Phase is to determine whether ECDA is feasible, and if so, to define the ECDA Regions and finally to select the Indirect Inspection Tools that will be used for each region. Typical overline techniques used for overline surveys include the following: Voltage gradient surveys ? DCVG or ACVG

Jan 1, 2006

By Ernie Holden, Chris Ringas

In the last 20 years, In Line Inspection (ILI) using intelligent pigs has become the principal tool used by pipeline operators to assess the condition of their pipelines. New pipelines are normally designed to take intelligent pigs, but many older pipelines require some modifications and special procedures for their inspection. This paper is aimed at practicing engineers and managers of pipelines, or people aspiring to those positions. The paper describes the benefits of ILI and some of the practical issues regarding pipeline preparation and cleaning, choice of inspection tool, running pigs in pipelines, and what to do with the data collected. What are the responsibilities of the Pipeline Engineer ? ? Maintain reliable and acceptable performance of the pipeline in terms of safety and product delivery at economical cost. ? Provide a defined margin of safety for operating the pipeline at its designated pressure. ? Provide timely information on all pipeline defects such that repairs can be carried out according to a managed schedule. What Defects does the Pipeline Operator have to cope with ? A useful record of actual incidents seen in pipelines can be obtained from the web site of the US Office of Pipeline Safety (OPS) - http://ops.dot.gov/stats/stats.htm. US pipeline Operators are obliged by Law to report all pipeline incidents exceeding certain threshold criteria (e.g loss of life, escape of product, cost of incident etc). These OPS statistics show that corrosion and third party damage have remained consistently the prime causes of reportable incidents in the US, with similar experience elsewhere. There are several kinds of flaws and defects in pipelines that can lead to failure, the main families being :- ? Metal loss ? Cracks or crack-like defects ? Laminations and other mid-wall defects ? Geometric anomalies

Jan 1, 2006

Standards And Laboratory Monitoring In Gold Assay Key Components Of Best Practice

Jan 1, 2005

By Mike McWha

Drivers to increasing RM use ?Compliance issues ?Section 12 JSE Listing Rules ?Canadian NI 43-101 ?Sarbanes Oxley ?Shortage of African ore reference materials ?Poor perceptions about quality of some local RM?s

Jan 1, 2005

By Christopher J. Oates

Overview ? Mining Codes ? Best Practice ? Mining Standards Guidelines ? Get it right from the start ? External Auditors ? The 5% rule ? MMCRM's - The Key Components ? The MMCRM Report / Certificate ? MMCRM's & Round Robins ? Summary

Jan 1, 2005

By G. Swan, E. Nordlund, P. Zhang

"SynopsisThe most widely used support design damage criterion for rockburst-prone mines is based upon kinetic energy, which is proportional to the square of the ejection velocity and is commonly expressed in terms of peak particle velocity (PPV). Field monitoring and back-analyses have shown that ejection velocities of the order of 10 m/s and higher can result from seismic events of moderate magnitude. Such velocities are much higher than those predicted using PPV obtained from scaling laws. It has also been found that the peak ground motion (i.e. PPV) on the surface of an excavation is preferentially amplified (by four- to tenfold) compared to the motion in solid rock at a similar distance from the source. However, the wave propagation and interaction processes involved within the fractured rock in generating high ground motion are very complex and are not well understood at this time.In this paper, velocity amplification was investigated by modelling the dynamic interaction between fractured rock and a free surface using a 2D discontinuum-based numerical program, UDEC (Universal Distinct Element Code). A 1D model with a fractured zone was used to represent the fractured rock. Velocity amplification, quantified by PPV, predicted at the free end of the model was 2.0–3.6 times higher than the input velocity. It was found that the wave frequency, fracture stiffness, fracture spacing, and thickness of fractured zone are the main factors that affect the velocity amplification. The results have proved that the interaction of the seismic wave and multiple fractures near the free surface strongly influences the ground motion.IntroductionSince mining-induced seismicity is almost inevitable in deep mines, ground support is generally employed to mitigate the risk of seismically-induced damage. The most widely used support design criterion for seismicallyprone mines is one that seeks to maximize the absorption of the kinetic energy (plus potential energy if a gravity component is considered) of key rock blocks. Based on this criterion, design methods for rock support were first proposed by Wagner (1984) in South Africa and later improved, among others, by Roberts and Brummer (1988) and Kaiser et al. (1996)."

Jan 1, 2015

By P. Rice, A. Photolo, A. C. Barnard

Introduction -Sampling Tool Project (STP) -History -Results to date -Costs -Questions

Jan 1, 2005

By M. A. van Nierop

The Discrete Element Method (DEM) is a model that is used to simulate the motion of the media in a grinding mill. The sum of the energy that is lost in inter-media and media-wall collisions represents the power drawn by the mill. The fact that the DEM predicts the power drawn by grinding mills over a large range of diameters has been used to show the validity of the DEM. However, the power drawn by a mill is a function only of the sum of forces of the load on the shell liners. A more accurate and detailed validation of the DEM would be to measure these forces as a function of angular position as the liner moves under the load, and to compare these measurements with predictions generated using the DEM. An experimental mill has been developed to reproduce exactly what the 2-dimensional DEM simulates. The 0,55 m diameter mill has a length of 0,023 m, which is fractionally larger than the diameter of the media used in the mill. One of the lifters in the mill has been instrumented so that the forces on the lifter can be measured as the mill rotates. The DEM simulation will be used to predict these forces. This will give experimental evidence of the validity of the DEM for modelling load behaviour in rotating grinding mills.

Jan 1, 1999

By N. E. Yasitli

There is a considerable amount of lignite reserve in the form of thick seams in Turkey. It is rather complicated to predict the characteristics of strata response to mining operation in thick seams. However, a comprehensive evaluation of ground behaviour is a prerequisite for maintaining an efficient production, especially when top coal winning by means of caving behind the face is applied. A comprehensive modelling of deformations and induced stresses is vital for the selection of optimum production strategy. In this study, numerical modelling and analysis of a longwall panel at Omerler underground coalmine have been carried out by using the software called FLAC3D developed based on the finite difference technique. Firstly, a 3-D numerical model of the M3 panel has been prepared. Secondly, induced stresses formed around the longwall face have been determined as a function of face advance where the face was located at the bottom of thick coal-seam. Results obtained from modelling studies have revealed that the front abutment vertical stress was maximum at 7 metres in front of the face and magnitude of front abutment stress was found to increase up to a distance of 200 metres away from the face start line. As the face was further advanced after 200 m from the face start line, there was not any significant change in the characteristics of front abutment stresses. Results of numerical analysis of the panel were in good agreement with in situ observations.

Jan 1, 2005

By Peter W. Lotz

Contents of: ?Sampling for Cyanide in Metallurgical Processes? ?Sampling at process level of operation ?Sampling at environmental level ?Sample stability and integrity issues ?each citing possible objectives, practical example and reasons for surprises Overall recommendations on sampling plans and procedures to maintain sample integrity

Jan 1, 2005

By Mark Dangerfield

[Power-Point Presentation]

Jan 1, 2005

By J. J. Botha

As a Demand Side Management (DSM) Project, money was granted for the procurement and installation of a 3-Chamber Pipe Feeder System (3-CPFS) at AngloGold Ashanti?s Moab Khotsong Mine in the Vaal River Area, Orkney. The first submission was done to ESKOM in December 2002 and the contract was signed in September 2006 at a cost of R 57-million with an envisaged reduction in power of 7 Megawatt per month based on a 90% utilization factor. The project was finally commissioned in December 2008. The technology is not new, but the intent of the paper is to share with others the experience gained by using the technology in a deep-level mine in order to reduce overall power consumption.

Jan 1, 2009

By L. Chanderman, C. E. Dohm

"Mineral Resource estimation (MRE) and classification are highly dependent on the confidence in the model of the orebody geometry, known as the geological model, within which the estimates are constrained. An understanding of the geology of a deposit is thus fundamental to the Mineral Resource evaluation process. The geological model is a function of the structural and depositional complexity of the geology captured by drilling information, which is limited in the early stages of a project. The information effect has a significant impact in terms of the interpretation of the geology as well as the estimation of grade continuity and the resultant risk associated with the Mineral Resource estimate and classification.Therefore, as new drilling information becomes available, it is necessary to update and refine the geological model to appropriately constrain the resource estimates. The grade information is also updated, including statistics and the spatial correlation characteristics. This refinement is based on geological interpretations derived from the drillhole information that becomes available throughout the life of the mine; orebody knowledge that comes from working experience of the deposit, as well as familiarity with the software package used for modelling, is also important.In updating, the potential to identify new resources in previously unknown areas may be realized. The opposite may also occur where previous interpretations of ore continuity are refuted. Both scenarios could result from a better understanding of the geology of the deposit and thus a more realistic MRE, which reduces geological risk. This paper describes how newly drilled advanced grade-control holes for a gold deposit in Mali were used to refine the 3D geological model for the deposit in an attempt to identify the potential for additional oxide ore using conventional geostatistical evaluation techniques."

Jan 1, 2017

By Reginald N. Boryor, Steven D. Woods

1.0 Introduction ?Low grade, high tonnage, open pit gold mine. ?Gold bearing Tarkwaian conglomerates. ?Reverse Circulation percussion drilling (25m X 25m grid). ?Composite 1m intervals, logged and split in the field to provide±2Kg samples. ?Samples used to build grade control block models using SURPAC. ?Approximately 100,000-130,000 meters drilled per year. ?RC samples are assayed using Rapid Cyanide Leach (RCL). ?Check assays are done using Fire Assay

Jan 1, 2005

By Conné Spangenberg

Contents ?Introduction ?Metal accounting environment ?Problem statement ?Investigations & Achievements ?Metal Accounting ?Principles ?Standards ?Audits ?Questions

Jan 1, 2005

EMMES Sampling Conference BACKGROUND & INTRODUCTION ?Impala acquires toll material to supplement production from ROM ?Toll material consists of filter cake, slurry and catalysts ?Samples are collected to determine the commercial values of the lots ?Slurry deliveries projected to remain relatively constant at 120tons dry solids per month, whereas filter cake deliveries set to increase five-fold to 800 tons dry solids per month ?Due to projected increase in toll material, new sampling and offloading facility presently under construction at Impala ?Presentation will cover two projects aimed at reducing the uncertainty associated with sampling of toll deliveries ?i.e. slurries and filter cake.

Jan 1, 2005

By Thermo Electron, Tim Sennett

Summary ?SamStat Development ?SamStat Description ?Accuracy ?Availability ?Cost of ownership ?Capital ?Installation ?Operating/Maintenance ?Case Studies ?Modikwa ?Combined concentrate sampling ?Cerro Verde ?State of the art sampling & analysis ?Ok Tedi Final Tails ?brownfields installation ?Conclusion

Jan 1, 2005

By S W. Robertson, A Vercuil, P Craven

Mintek is currently developing a design approach for the heap leaching of low-grade primary copper sulphide material. Since the leaching of chalcopyrite requires elevated temperatures, the generation and management of heat within the heap is crucial. Furthermore, the precipitation of iron needs to be managed to prevent premature blinding of the heap, and acid consumption needs to be limited to contain cost and limit the dissolution of gangue impurities. Standard column tests using jacketed 1-m and/or 6-m columns do not allow accurate prediction of temperature changes and heat generation in an actual heap. Mintek therefore utilizes a computer model to calculate the energy balance and heat generation with time, based on the measured sulphide oxidation rates in the column. The temperature in the column is then adjusted to reflect the computer-predicted temperature in an actual heap. Using this approach, an overall copper extraction of 70% was achieved in 120 days, using 1-metre columns, when treating an ore blend containing 1.36% chalcopyrite, 0.23% chalcocite, 0.07% covellite, 3.8% pyrite and silicate gangue (92%). The chalcopyrite contribution to the total copper content in the feed was 75%. This was followed by 6-m columns using a similar approach, and the column results will be validated on a 23,000 tonne test heap. Key Words: heap; bioleach; chalcopyrite

Jan 1, 2005

By D. N. Ferguson

The separation of certain minerals by electrostatic techniques can be difficult due to their similar electrical conductivity, and any technique to improve this can be useful in certain difficult separation applications. Triboelectric differences between mineral scan result in certain minerals acquiring small positive or negative charges prior to inductive electrostatic separation. By changing the polarity of inductive separation, relative changes in mineral recovery can be observed, which may be beneficial. In this brief study a JKTech mineral liberation analyser (MLA) was used to evaluate the effect of polarity change on selected minerals present in the Richards Bay Minerals deposit, and an approximate triboelectric series based on this behaviour is presented.

Jan 1, 2010

INFACON conjures up many things for many people. For the fortunate few who have been actively involved with this event since its inception, it brings back memories of far places, stimulating debates and above all, the people who have over the years contributed to the outstanding success of the Congress and who have added to the wealth of knowledge on all aspects of ferroalloys. The International Ferroalloy Congress (INFACON) has been held every three years since 1974. INFACON X will be held in Cape Town in February 2004. Simple arithmetic shows that next year?s Congress should in fact be INFACON XI. Thus, one Congress was skipped. INFACON 74, as the name implies, was held in 1974, in Johannesburg, South Africa. The event was sponsored by the Ferro Alloy Producers? Association of South Africa (FAPA), the National Institute for Metallurgy (NIM - Mintek as it is known today) and the South African Institute of Mining and Metallurgy (SAIMM). You will see some of the same sponsors involved in INFACON X. Dr. Robbie Robinson, renowned academic and past president of the SAIMM, was the Chairman of the Organising Committee. The editor was Dr. Helen Glen. Anyone fortunate enough to possess a copy of the proceedings of this first Congress will agree that from a literary and technical perspective, it is still the benchmark for subsequent events. A unique feature of INFACON 74 was the use of rapporteurs (my first duty) to ensure that the discussions following the presentations were recorded (in direct speech) as accurately as possible. This involved time-consuming correspondence (can you imagine life before e-mail?) to all parts of the world between the author and the person posing the question, with the rapporteurs acting as go-betweens. It is understandable that the much-awaited proceedings only saw the light in 1975. The names recorded in the proceedings as the members of all six committees read like the who?s-who of the South African ferroalloy industry at the time: Dr. Peter Jochens, Mr. Harvey Reid, Mr. Piet Streicher, Prof David Howat, Mr. Sigurd Selmer-Olsen - to name but a few. The Congress was held in the new, very fashionable and upmarket Carlton Hotel in the CBD. In the Foreword of the proceedings, Dr. Robinson provides an insight into the event. Three hundred and thirty six delegates from twenty two countries attended the Congress, which was opened by the Honourable P.G.J. Koornhof, Minister of Mines. Again, the opening address makes fascinating reading. During the Congress an ad hoc committee was convened as the first International Committee on the Organisation of Ferroalloys Congresses, with representation from the main ferroalloy associations of the world. The following decisions were recorded: ? The Congress would be continued at three-yearly intervals under the name of INFACON ? Every third Congress would be held in South Africa ? NIM (Mintek) would provide the permanent secretariat. Six technical sessions were held, each preceded by a plenary address with a closing address by the session chairman. In all, thirty technical papers were presented. Prior to the closing address, a panel discussion on factors affecting the future of the ferrochromium industry provided stimulating debate in the form of a question-and-answer session. The hosting country for the next INFACON would be announced. Eventually, word got round that the next INFACON would be held in Japan. However, due to unforeseen circumstances, the event was cancelled ? thus no INFACON 77. INFACON 80 was subsequently held in Lausanne, Switzerland from 12th to 16th October 1980. The event was organised by IFPEO, Institut des Producteurs de Ferro-Alliages d?Europe Occidentale. The Congress was officially opened by the President of IPFEO, Mr. R. Björklund, who was also President of the Organising Committee. The technical sessions were held in the Palais de Beaulieu. The Congress was well attended by 400 participants from 28 countries as well as 100 accompanying ladies. A total of four plenary addresses and 18 technical papers were presented. As with the first event, an international panel discussion (questions and answers) preceded the closing address. In his closing address, Dr. Louw Alberts, Chairman of the International Committee on Ferroalloys and President of NIM, presented an insight into the factors affecting growth in the industry and where growth was likely to take place. Twelve exhibitors had stands at the Congress. Attendees could choose from four post-event tours to Belguim/France (SADACEM/Compagnie Universelle d?Acetylene et d?Electro-Metallurgie), France (CUAEM), Finland (Outokumpu Oy) and Norway (Elkem Fiskaa plant).

Jan 1, 2004