Search Documents

By J. Kim, H. Cho

The objective of the experiment was to investigate the efficiency of hindered-settling column in recovering carbon from anthracite. Two types of Korean anthracites were prepared for feed materials. Each sample was crushed and classified by size, and washability analyses were performed. Separation efficiency was evaluated under various operating conditions using a laboratory scale hindered settling column. Results showed that the carbon recovery was higher for the smaller sizes, but the purity of the product was better for the larger sizes. In, overall, 2-0.21mm particles of 40-45 % ash could be processed into about 20 % ash products.

Jan 1, 2002

By D. W. Olson

The estimated value of natural gemstones produced from U.S. deposits during 2004 was $12.9 million. This was a 3-percent increase from that of 2003. U.S. gemstone production included agates, amber, beryl, coral, garnet, jade, jasper, opal, pearl, quartz, sapphire, shell, topaz, tourmaline, turquoise and other gem materials. More than 60 varieties of gemstones have been produced commercially from U.S. mines. But commercial mining of gemstones has never been extensively undertaken in the United States. Most of the deposits have been relatively small compared with other mining operations. In the United States, much of the current gemstone mining is conducted by collectors, gem clubs and hobbyists rather than business organizations.

Jan 1, 2005

By J. P. H. Steele, M. U. Ozbay

As mining operations progress toward tele-mining and autonomous procedures, the need for machine performance monitoring increases. Presently, through a combination of vision, sound, and other subjective observations, an operator attempts to optimize the mechanical excavator’s operation. As the operator is moved away from the face in the case of tele-mining or completely removed for autonomous operation, the qualitative sensory input is lost. This lost information must be replaced with quantifiable sensory input. Chip formation detection may be a suitable replacement sensory input. Chip formation can be predicted with high confidence (>80%) through the analysis of the load waveform associated with the bit/rock interface.

Jan 1, 2002

By Marianne Snedeker

In September 1985 we published a questionnaire asking about the content of MINING ENGINEERING and about your interests. By Dec. 10, our cutoff date, we had 430 responses, representing about 1.5% of the 28,238 people who received the September issue of ME. In the data that follow the tabulation and percentages are based on the number of individuals who responded to the particular question. About ME Through responses to the questionnaire, we were hoping to learn more about you, your interests, and how the magazine could better serve you. Those of you who responded told us something positive - you look at or read the magazine. Of the 430 respondents, 428 or 99.5% indicated that they had read or looked through the July and/or August issues. Those of you who refer to the magazine once are 207 or 48.5%. Those of you who refer to the magazine two or three times are 193 or 45.2%. Those of you who refer to the magazine four or more times are 27 or 6.3%. How much time do you spend reading the magazine? Of those responding to this question: 64 spent up to 1/2 hr 15.0% 224 spent up to 1 hr 52.6% 115 spent up to 1-2 hr 27.0% 23 spent more than 2 hr 5.4% In an informal survey among our staff, we determined that most people spend 1/2 to 1 hr reading magazines to which they subscribe at home. Does that match your experience? Many of you, 335 or 79%, clip your magazine for further reference. Also, many of you, 313 or 73.6%, do not pass your copy on to another reader, indicating that you are clipping it or receiving the magazine at home. Those magazines that are passed on reach: 1 person 3 0.7% 2 people 64 15.1% 3-5 people 34 8.0% 5 or more 11 2.6% Answers to what portions of the magazine you find useful indicated that the top three were Industry Newswatch, feature articles and Technical Papers; see Table 1. The "other" category included advertising - display, classified, Employment, and Professional Services - Washington Survey, New Products, Free Literature, book reviews, technology news, and Coming Events and Short Courses. We asked your appraisal of the technical level of the magazine. Of those responding, 39 or 9.1% indicated that it is too technical, 55 or 12.8% indicated it is not technical enough, and 335 or 78.1% judged it to have the correct technical level. In response to the question about whether you like to read an occasional feature that is not technically oriented, 21 or 5.1% said no, but an overwhelming 94.9% (393) said yes. Of the specific

Jan 1, 1986

By Richard F. Coon

Six potential locations along the west shore of Lake Mead were evaluated to site anew water intake pumping station for the SNWA. The evaluations were based upon geotechnical exploration results and conceptual intake pumping station designs. The exploration included geologic mapping, geophysical testing, underwater ROV inspections and borings. Ground surface and underground chamber pumping station designs were considered. Sites at Saddle Island, Black Canyon and Hoover Dam are geotechnically suitable. A Saddle Island site was selected because it has the most favorable conditions for the intake pumping station and the aqueduct to the Las Vegas valley.

Jan 1, 1997

By Mark E. Smith

Oxide ores can consume enormous amounts of expensive sulfuric acid. The problem is amplified with increasing heap heights. One solution is to provide a thin liner and drainage system between each lift of ore, thereby intercepting the pregnant leach leach solution (PLS) after it exits the active lift. However, these liner systems require special attention to hydraulics, slope stability and geomembrane design criteria. Inadequate attention to the first two can result in reduced recoveries, increased acid consumption andsystem failures. The geomembrane selection criteria are different from the base liner, and optimizing its selection can have significant effects on the operation’s bottom line.

Jan 1, 1996

By J. F. Lupo

Heap and valley leach operations rely on solution collection piping placed within the heap to enhance both solution recovery and to assist overall solution management. The most common piping used in leaching operations is solid or perforated High Density Polyethylene (HDPE) pipe and Corrugated Polyethylene pipe (CPE). These pipes are widely used because of their low cost, ease of installation, durability, and flexibility. The typical recommended maximum design depth of burial for HDPE and CPE pipes is on the order of 30 meters (100 feet). However, ore heap heights at many facilities exceed 30 meters and some are now approaching 180 meters (600 feet) in height. At very high ore heap heights, the stability and performance of HDPE and CPE pipes becomes a critical issue for leaching facility design and operation. Failure of solution collection piping can lead to poor solution recovery, high hydraulic heads on the liner system, and in some cases, unstable ore slopes due to high solution pressures near slopes. This paper presents a review of methods that have traditionally been used to evaluate pipe stability under high normal loads. A common shortcoming of these methods is the inability to account for beneficial effects of ore arching around pipes and the time-dependent creep (stress relief) behavior of polyethylene (PE) materials. A new analytical approach is developed and presented which includes the effects of ore arching around pipes and creep of PE materials. The results of the new approach show that PE pipes will deform under high heap loads, but can remain stable and functional. Pipe stability is shown to be dependent on the type of pipe backfill and initial backfill compaction. The new approach represents a useful tool for designing applications for PE pipe under high normal loads.

Jan 1, 2001

By J. Darlington, A. K. SenGupta

Water-swellable layered silicates, namely, the smectite clays can remove suspended materials (called herein as debris) and metal ions from aqueous streams. The present study shows that the flocculating and metal extracting abilities of smectite clay-based flocculants can be enhanced when these clays are used in conjunction with a specific anionic polymer. Such performance enhancement is attributed to the following: i) the clay-dispersing ability of the polymeric additive, that would translate into an increase in the clay-surface area available for the attachment of the debris particles onto the clay particles; ii) the possibility of dispersant-to-coagulant transition of the polymer during the later instants of the treatment process, as a result of reduction in solvency of the wastewater for the polymer due to the release of cationic species from the clay-based flocculant solids; iii) metal-complexing ability and adsorption properties of the polymer.

Jan 1, 2002

By S. Ersayin

In 1998, the Concentrator Modeling Center was established within the Coleraine Minerals Research Lab to develop models for simulation of iron ore processing plants, and to assist plant operators in improving performance of their aging plants. The short-term objective was to develop necessary models for reliable simulation using conventional techniques, while the long-term objective was set as liberation-based modeling and simulation of these plants. The short-term objective was achieved in 2002, after the development of models for magnetic separators, hydroseparators and fine screens. A project funded the US Department of Energy was carried out to demonstrate the capability in improving iron ore processing at the Mittal plant. As a result of this study, a 10% improvement in throughput at the plant was obtained, and simulation became a desired tool for plant operators. A significant step in the long-term objective was reached in 2005 with the development of a liberation model. This was followed by incorporation of models capable of processing liberation data into the software. By early 2007, the Center had the capability of performing liberation-based simulation of entire plants.

Jan 1, 2008

By Jeffrey A. Pontius

The Cresson gold deposit is in the southcentral portion of the Cripple Creek mining district in central Colorado (Fig. 1). The deposit is hosted by a series of 32 Ma (Kelley, 1995) felsic to mafic, alkaline volcanic rocks that were deposited in a diatremal environment. Mineralization in the Cresson deposit is structurally con-trolled. It occurs as disseminated and vein type. Gold deposition is closely associated with potassium-pyrite metasomatism and quartz-telluride vein development(Pontius, 1992). The Cresson deposit is owned by the Cripple Creek and Victor Gold Mining Co. (CC&V), a joint venture between Pikes Peak Mining (67%) and Golden CycleGold (33%).

Jan 1, 1996

By D. Bogh

Wound rotor motors are used in difficult mining applications where there is a need to start high inertia, hard starting loads while limiting inrush current They are recognized as robust and simple to control. This paper will cover the performance, specification, and important issues to be considered when applying medium voltage wound rotor motors in mining applications. Medium voltage grinding, crusher, and conveyor applications will be discussed. Specifically covered are motor efficiency, speed range, and rotor control. Crane motors often have wound rotor construction, but their load cycle and ratings are outside the scope of this paper.

Jan 1, 2011

By M. S. Riyazulla

A model of a new laboratory magnetic separator has been conceived to cater the needs of process engineers and mineralogists world over engaged in mineral characterization and beneficiation. It would be essentially a laboratory instrument for the separation and concentration of various ferro and non-magnetic minerals. Based on the basic concept of Frantz Isodynamic Magnetic Separator, the new separator conceived would not only speed up the work of a process mineralogist and save the energy, but it would effectively separate and sequentially produce about fourteen fractions at a time. In the present paper, the probable operational procedures and the design have been discussed in detail for the various mining companies to assess its economic feasibility. If it could be fabricated, it would have a worldwide market The concept has been patented in author?s name in India.

Jan 1, 2009

By M. M. Poulton

Universities are not immune from the large number of retirements facing the mining industry. Department heads anticipate that we will need to replace all of the senior mining engineering faculty in the U.S. by 2020. Long term studies of Ph.D. completion times and success rates indicate that in Engineering disciplines in the U.S., the ten year completion rate is 65% at best and the four year completion rate is less than 8%. We do not have accurate data on completion rates and times for mining or metallurgical engineering Ph.D. students in the U.S. but students self-report their expected completion times are around 4 years. National data on doctoral students indicate that younger, full time students with sufficient financial support have a higher probability of success in completing their degrees in a timely manner. Students in Eastern U.S. mining engineering programs are on average 32 years old, 85% are full time, and the gap between support and cost of attendance is $5,000 per year. Students in Western U.S. programs are on average 38 years old, 78% are full time, and the financial gap is $8,483. Further, it appears that domestic graduate students are not very geographically mobile. The current demand for new faculty is higher in Western programs but the longer term retirements are higher in Eastern programs. While all Ph.D. students who responded to the 2010 survey indicated an interest in a faculty position at some point in their careers, very few were applying for the open positions. Over the past 35 years for which data could be obtained, the maximum number of Ph.D. students enrolled in mining engineering in the U.S. is 115 with a maximum of 27 degrees granted in one year. On average 89 students are enrolled in doctoral programs in mining engineering in the U.S. with average degree production of 15 Ph.D.s per year.

Jan 1, 2012

By M. E. Kuchta

Research is currently being conducted at the Colorado School of Mines in the use of high-pressure water for scaling down loose rocks in underground mine openings. In addition to improved miner safety, the adhesion strength of shotcrete applied to rock surfaces treated with high-pressure water is also increased significantly resulting in improved overall support capabilities of the shotcrete layer. Test results show an increase in adhesion strength by a factor of four on a concrete test wall cleaned with water at 21 Mpa (3000 psi) as compared to a surface cleaned at 0.7 Mpa (100 psi).

Jan 1, 2002

By Ben Sosewitz

The subject of rapid excavation tunneling is one that is extremely important to the people in the Metropolitan area of Chicago. My personal observation is that it is also extremely important to the urban communities around the U.S., to many local and state governments, and to the public officials who are deeply concerned about state affairs and taxes. The Metropolitan Chicago area is in fact, (as are 40 other major urban areas in the U.S.) confronted at the present time with a very serious combined sewer overflow, drainage and pollution problem which accounts for an estimated 40% of the pollutional load on its waterway system. In response to this the District has to date spent some seven millions of dollars in an attempt to find the most economical solution available for the elimination of this problem. This study included extensive investigations of the geological strata, the quantity and quality of storm runoff to be dealt with, and the various methods of storage and treatment available. It has considered solving the overflow problem by a concept involving a series of tunnels, rock tunnels, shafts and storage areas which will collect, retain and subsequently treat that portion of the combined sewer overflow which can be handled in the most cost-effective and economical way, consistent with following the federal and state standards - with which we at the present time agree in principle.

Jan 1, 1997

By P. van der Veen

The objective of this paper is to analyze the evolution of the strategic drivers of the mining sec-tor over the last half century, which has been guided by a varying and expanding list of motivations. While companies cannot survive for long unless they are making profits, the strategic drivers of the industry have gone far beyond profits since at least the mid-1970s when environmental concerns began to be taken seriously. For the most part, these forces have followed global trends and public opinion, but they have been shaped and magnified by the significant, often dominant role that the mining sector plays in many economies. While the mining sector used to be primarily motivated by the first pillar of sustainable development -i.e. the economics pillar-, in the 1970s the second environmental pillar became an important factor in decision making, and in the 1990s the third social pillar emerged as a major driver.1 The entrance of new strategic drivers has also had considerable impact on technological and organizational developments in the mining industry; however, technological changes, driven by cost reduction considerations, have in turn impacted the strategic drivers of the industry, resulting in the need for further technological and organizational developments.

Jan 1, 2007

By T. R. Ellis

Australia’s mineral valuation code continues to evolve, while mineral valuation standards are also being written for Canada and Southern Africa. The author is leading a task force for writing the extractive industries addition to the International Valuation Standards. Meanwhile, the International Accounting Standards Board is continuing the development of an extractive industries addition to its International Financial Reporting Standards, with an emphasis on valuation reporting. This paper analyzes the need, content and ownership for a U.S. minerals appraisal standard in the context of both these developing international standards and also existing U.S. regulations and appraisal standards. The author provides many questions for research and debate.

Jan 1, 2003

By Nathaniel Arbiter

In contrast to pyrometallurgy's 6000year history in metals production, hydrometallurgy is of relatively recent origin. The earliest reference to it was in the 16th century, with the first applications to copper in the 17th and 18th centuries. In the 19th century, increased demands for pure metal resulted in the development of electrolytic refining, and early in this century electrowinning. The rapid growth in copper production in the 20th century, particularly in the United States and Chile, stimulated the development of new technology for leaching and for the recovery of copper from leach solutions. In the past 25 years, solvent extraction has become a major factor by permitting novel leaching technology that produces dilute or complex solutions. In addition, solvents other than sulfuric acid, and chemical methods for precipitating copper metal are now of increasing interest. These are trends that should grow in importance with the need to process lower grade and more complex materials. The evolution of copper hydrometallurgy is reviewed. Key factors in recent major developments are presented with details of specific operations and with trends for the future indicated. The relative importance of copper hydrometallurgy is compared with that of pyrometallurgy in the light of probable changes in ore supplies and character.

Jan 1, 1994

By Lane White

The 1989 Annual Meeting and Exhibit of SME in Las Vegas, NV, February 27 - March 2, 1989, was the largest ever, drawing more than 4000 regis¬trants and 240 exhibit booths. Technical sessions included presentation of nearly 500 papers, including symposia on Biotechnology in Minerals and Metals Processing, Surplus Capacity in the International Metals Industry, and APCOM `89 - the 21st International Symposium on Application of Computers and Operations Research in the Mineral Industry. Technical sessions covered the gamut of minerals industry interests; however, the proximity of the meeting to recently surging gold development in Nevada drew special attention to gold operating practices. Several of the papers on gold processing are reviewed below. To keep pace with the strong world- wide interest in gold development, SME has scheduled three additional upcoming programs that will focus specifically on gold: World Gold '89 - Gold Forum on Technology and Practices will be held November 5 - 8, 1989 in Reno, NV, as a joint meeting and exhibit between SME and the Australasian Institute of Mining and Metallurgy. Technical sessions will encompass a full program of papers covering geology and exploration, mining, and mineral and metallurgical processing. Cooperating sponsors for this meeting include the Canadian Mineral Processors Division of CIM, The Institute of Metals, The Institution of Mining and Metallurgy, The Mining, Geological & Metallurgical Institute of India, and The South African Institute of Mining and Metallurgy. Gold '90 - Salt Lake City, UT, February 26 - March 1, 1990, will be a symposium held in conjunction with the 1990 SME Annual Meeting. Current research on the processing of refractory gold ores will generate innovative papers on process mineralogy at this symposium, with special emphasis on gold with pyrite and gold with carbon. Other sessions are planned for gold exploration and mining, gold metallurgy, gold plant design and practice, and gold in scams. Advances in Gold and Silver Processing Conference, October 1 - 3, 1990 will be held in Reno, NV. Preliminary planning calls for technical sessions on heap leaching practice, refractory ore processing, non-traditional lixiviants, bioleaching, metal recovery from solution, and the environmental aspects of processing operations. PLANT DESIGN, OPERATION Technical sessions organized by the Minerals and Metallurgical Processing Division of SME at this year's meeting in Las Vegas covered a wide range of gold operating practices. Eight papers relating to gold plant design, operation, and equipment are summarized here. Preprints of these papers are available by writing to Publications Sales, PO Box 625002, Littleton, CO 80162-5002 ($2.50 per paper for AIME members, $4 for nonmembers). Continuous elution process A. M. Stone, of Bechtel Australia Pty. Ltd., described the "Development of the Continuous Elution Process for Extraction of Gold from Carbon" (pre-print 89-75). Developed by Bechtel Pacific Corp. for Ok Tedi Mining Ltd., the Continuous Elution Process uses the same reagents as batch processes for elution of gold from carbon, while yielding significant savings in stripping vessel size and energy consumed in comparison with equivalent batch processes. The process is also simpler to operate than batch processes. Other advantages include reduced maintenance costs, higher average eluate grade, and near steady final eluate grade. Pilot testing for the Continuous Elution Process was conducted at Western Mining's Kambalda gold plant beginning in December 1982. The Continuous Elution Process is a continuous countercurrent system operating in a pressure vessel at elevated

Jan 1, 1989

By Z. T. Bieniawski, E. H. Skinner, R. A. Cummings, F. S. Kendorski

INTRODUCTION Caving Mine Drift Support Design The support of production drifts remains a high-cost item facing the developer or operator of an underground caving mine. Support costs are incurred well in advance of ore production, and there is a strong need to minimize these pre-production commitments of capital. Due to the extensive rock loads that normally develop during the caving process, the support used in caving mines is typically quite heavy and therefore costly. The process of designing this support increasingly makes use of basic tunneling principles, but is hindered by the still-incomplete state of knowledge of rock behavior in caving mines, and high variability of geological conditions in caving orebodies. Caving mines differ from tunnels in that the deformations and rock loads induced are transient and dynamic in occurrence, and are normally large in magnitude, often well in excess of rock mass strength. As opposed to tunnels, caving mine layouts are more intricate, and the methods and effects of construction ordinarily are not as closely monitored. Safety factors in mining tend to be lower and rock masses tend to he weaker. These aspects prevent strict application of tunnel design technology to caving mine drift support, with the result that mine drift supports are commonly designed chiefly on the basis of experience at other mines. Mining procedures at caving mines are evolved in response to site-specific requirements, to the extent that there are really as many caving methods as there are caving mines.

Jan 1, 1983