Search Documents

By J L. Mauk

 Broken Hills is an adularia-sericite epithermal Au-Ag deposit, hosted in flow-banded rhyolites and overlying rhyolitic pyroclastic rocks in the eastern Hauraki Goldfield. The 7.1 Ma deposit was the largest producer of gold in the eastern Hauraki Goldfield, and was one of very few economic deposits hosted in Pliocene rhyolites. This paper presents the results of a recent study in the upper levels of the deposit. Maps and cross-sections constrain structural and lithological relationships, and the lateral and vertical extent of a breccia pipe û the major feature of the upper levels.   Previous studies in the upper levels of Broken Hills have shown that gold and silver values are concentrated around and within a large breccia pipe, mined by a series of æcaveÆ stopes and in veins. Contour diagrams of Au-Ag data from channel samples indicate that the breccia pipe was a major fluid channel-way for mineralising solutions.   The breccia pipe deposits are part of the dynamic geothermal system that formed the Broken Hills ore bodies; they developed as a result of hydrothermal brecciation in areas of structural weakness within a rhyolite pyroclastic unit that overlies a massive rhyolite lava-flow unit. The main breccia pipe begins near the rhyolite/pyroclastic contact, having the shape of an inverted, inclined cone, and consists of silicified breccia, stringers of quartz, and irregular patches of clay-altered country rock. Smaller zones or pockets of hydrothermal eruption breccia are silicified and contain low grade gold in the matrix and in the adjacent silicified wall rocks.   Quartz has been classified according to its physical characteristics as seen in situ and hand specimens indicate that vein definition decreases upwards, perhaps as a result of changing lithological conditions and/or increasing proximity to the paleosurface. Hydrothermal quartz is widespread as veins and as a replacement mineral, or lining fractures and cavities and overgrowing rock fragments. Breccias contain vein quartz, but some quartz veins cross-cut breccias, indicating that vein and breccia formation was relatively synchronous and overlapped in time.   Disseminated gold-silver mineralisation is associated with vein quartz and silicic alteration of the wall rock within the breccia pipe. The auriferous zones are highly irregular and erratic, and sampling results show a wide range of gold-silver ratios, suggesting that highly volatile physiochemical conditions prevailed during mineralisation.

Jan 1, 2005

By P. Ulrich, V. Svalbonas

The early to mid 1980s was a period of mining consolidation, and many senior design engineers retired from the mill industry. Similar conditions have existed in the last few years. This creates a loss of a tremendous amount of experience. This paper is a look back by two senior mill designers who survived the dips in both time periods. From a continuous design practice of over 25 years, mill designs and fabrication practices are surveyed with a view of identifying what works, and is necessary, and what doesn’t, or is not necessary, in the creation of a safe, economic, long-lived grinding mill.

Jan 1, 2001

By Hinde J. S

The Fitzpatrick Orebody is a three and a half million tonne fault bounded portion of the early-middle Proterozoic Broken Hill Orebody.The Fitzpatrick Orebody was discovered in 1975 by diamond drilling from the 36 Level Exploratory Drive. This followed persistent geologically oriented exploration and a courageous decision by mine management to deepen No. 3 Shaft to provide exploratory development across the Globe Vauxhall Shear and allow effective drilling of the target area.The stratiforrn oebody consists of three lenses, the lead rich No. 2 and 3 Lenses and smaller zinc lode. They represent a down plunge extension and boudinaged, fault-bounded portion of the main Broken Hill ore lenses. The surrounding host rocks are extensively faulted and jointed due to complex history of movement on the bounding shears. This results in extremely poor ground conditions during mining. The ore was delineated for mining development using three dimensional fan drilling from exploratory and hanging wall drive drill sites.

Jan 1, 1990

By Joe F. T. Agapito

High stresses and adverse geology in deep coal mines in the state of Utah, USA, have caused numerous bumps. The larger bumps have been associated with seismic events with Richter magnitudes of 3.6 and greater, and in some cases have filled openings for lengths of 150 m. A better understanding of the mechanisms and stress levels involved in bumping is needed to help develop improved stress control design and bump mitigation methods. The geology of the area is notoriously bump-prone. The coal has poorly developed cleating and occurs in multiple seams that are often bounded by very strong roof and floor sandstone/siltstone beds. The overburden is formed by thick, competent strata with numerous sandstone channels This geology and deep cover are the major source of high stresses, causing bumps. This paper evaluates live common stress factors responsible for bump problems: depth, sandstone channels, arching, faults, and coal thickness. It uses ease study data from longwall panels with two-entry/yield pillar systems typical of deeper Utah mines. Results illustrate the importance of analyzing stress factor experience to allow a better understanding of the problem.

Jan 1, 2000

The National Mining Hall of Fame will induct five mining greats on Saturday, Sept. 17, 2005 at the Museum Convention Center in Leadville, CO. The 18thAnnual National Mining Museum and Hall of Fame Induction Banquet will begin with an open house and reception at 5:30 p.m., followed by the dinner and program at 7 p.m. The five inductees are Nathaniel Peter Hill, John Munro Longyear, John McDonald, Julius Eckhardt Raht and John Dennis Ryan. Nathaniel Peter Hill (1832-1900) built the first successful smelting operation in the Rocky Mountains in1867 at Black Hawk, CO. From 1879 to 1885, he was a U.S. senator. He also taught courses at the Colorado School of Mines.

Jan 1, 2005

By Marc Ruest

A new instrumented cable bolt has been developed by the National Institute for Occupational Safety and Health at the Spokane Research Laboratory in Spokane, WA. Although various instruments are available to measure load distribution and magnitude along a grouted cable, this instrument is innovative in that it uses strain gauges internal to the cable as load-measuring sensors. The instrument has been successfully tested in the field at FMC?s Granger Mine, Meikle Mine, and Getchell Mine. A ?split-pipe? laboratory pull test was performed on each of three cable bolts instrumented with the new device. Each test consisted of grouting a 1.83-m-long cable in two 0.91-m-long sections of schedule 80 pipe. A numerical analysis was then performed in which laboratory boundary conditions were simulated and model properties derived from textbook guidelines. The loads calculated by the model were then compared to the measured loads.

May 1, 2002

By Marc Ruest, Lewis Martin

A new instrumented cable bolt has been developed by the National Institute for Occupational Safety and Health at the Spokane Research Laboratory in Spokane, WA. Although various instruments are available to measure load distribution and magnitude along a grouted cable, this instrument is innovative in that it uses strain gauges internal to the cable as load-measuring sensors. The instrument has been successfully tested in the field at FMC’s Granger Mine, Meikle Mine, and Getchell Mine. A “split-pipe” laboratory pull test was performed on each of three cable bolts instrumented with the new device. Each test consisted of grouting a 1.83-m-long cable in two 0.91-m-long sections of schedule 80 pipe. A numerical analysis was then performed in which laboratory boundary conditions were simulated and model properties derived from textbook guidelines. The loads calculated by the model were then compared to the measured loads.

By F. D. Fox

The Flambeau and Ridgeway Mines, both owned and operated by wholly owned subsidiaries of Kennecott Minerals Company, were located very close to populated areas having initial concerns about health, safety and the environment. The success of both operations depended upon developing a framework of community support and enhancing sustainable development opportunities throughout the entire life cycle of the mining operations to address these concerns. The protection of the Flambeau River was the cornerstone of the Flambeau Mine’s success. The highest priority for the Ridgeway Mine was to ensure long-term physical, chemical and ecological stability of the reclaimed mine site. Both of these goals have been achieved and are discussed in this paper, which highlights Kennecott Minerals Company’s integration of sustainable development principles into its business decision-making and management processes.

Jan 1, 2003

By James H. Rowland

The Mine Improvement and New Emergency Response Act of 2006 (MINER ACT) established a Technical Study Panel (The Panel) to provide recommendations on the utilization of belt air and new technology that may be available for increasing the fire resistance properties of conveyor belt used in underground coal mines. The Panel Report recommended use of the Belt Evaluation Laboratory Test (BELT) as the method for testing and approval of flame resistant conveyor belts used in underground coal mines. The research conducted to establish the correlation of the BELT with large-scale belt fire flammability tests was done using 36- to 42-in wide conveyor belt. Due to today?s coal haulage capacity, the mining industry is using 72-in and wider conveyor belts. The National Institute for Occupational Safety and Health (NIOSH) conducted a study to determine if the BELT will also qualify wider belts as fire resistant for use in underground coal mines. This paper describes the results of recent experiments comparing results from using the BELT and the large-scale tests for six different belts.

Jan 1, 2010

By W. G. Davenport

The flash furnace is used for smelting concentrate to (i) high-Cu matte and (ii) molten metallic copper. It is also used for converting solidified/crushed matte to molten metallic copper. This is flash converting. It consists (Table 20.1, Fig. 20.1) of: (a)tapping molten 65 to 72% Cu matte from a flash smelting furnace (b) granulating the molten matte to ?1/2 mm particles in a 103 m3/hour water torrent (c) crushing the granulated matte to 50 µm in a vertical roller mill (d)drying the crushed matte (e) feeding the dry particulate matte to a second flash furnace for oxidation converting to molten copper. In 2000, flash converting is being used by Kennecott Utah Copper (George, et al; 1995; Newman et al, 1998, 1999a,b). A second installation is being designed for the Chuquicamata smelter (www.outokumpu.com [October 12, 2000]), The potential uses of flash converting are: (a) as the second half of a flash smelting/flash converting coppermaking sequence (b) as a continuous converting alternative to batch submerged tuyere converting. This chapter uses our flash furnace matrix to determine the %O2-in-blast, industrial oxygen and oil requirements for converting solidified 65% and 72% Cu matte to molten copper. It then discusses choice of feed matte grade and other aspects of the process.

Jan 1, 2001

By L. Betteridge, A. Marks

"An OK 300 cu. ft. Skim - Air cell was installed at the HBM&S concentrator in Flin Flon in 1987. Since that time, 3 additional OK Skim - Air cells have been installed in HBM&S concentrators. The cell treats a coarse 70% solids slurry with a residence time of 2.5 minutes. The product from the cell (a unit cell type application) is a final grade copper concentrate with high precious metal values. Since its installation, the cell has improved gold recovery by 10 - 15%. Process variables such as circulating load, pH, froth depth, feed size, and reagent additions all have an effect on the operation of the cell. Maintenance on the cell has been minimal. Initial operating problems involving level control have been significantly reduced and operations are now relatively trouble free. Although very successful at Flin Flon, site specific operating circumstances will determine the suitability of this cell. INTRODUCTIONHudson Bay Mining and Smelting operates four concentrators in Northern Manitoba. Three treat copper-zinc ores, the fourth mills a copper-nickel ore. The Flin Flan concentrator operates two circuits in parallel which treat copper and zinc ores from the Trout Lake and Callinan mines. Both circuits in the Flin Flan mill have Skim-Air cells integrated into the grinding circuits.The Trout Lake cell was installed first and had a payback period of a few months. Required modifications to the cell were made to enhance its performance. These included changing the discharge valve size, tuning the level controller, and installing an insert into the rubber valve sleeve to increase its wear life. The payback period on the Callinan cell was significantly reduced because these modifications were completed prior to its installation.The cells produce a final grade copper concentrate and since their installation gold and silver recoveries to the final copper concentrate have increased significantly. Operating parameters such as coarseness of cell feed dictate the metal recoveries and froth depth determines the selectivity of the cell and therefore the grade of the concentrate.The Skim-Air cell can be suitable in applications where a final product is generated. However, when a bulk concentrate, which requires further separation, is produced, the coarseness of the product may not make it amenable to conventional flotation.The Flin Flan mills Skim-Air cells have worked exceptionally well with little maintenance required."

Jan 1, 1991

"The first SkimAir flash flotation cell was installed in Outokumpu’s Hammaslahti Copper Concentrator in 1982 to prevent overgrinding of soft sulphides in the milling circuit. Since this first installation the popularity of the flash flotation has fluctuated depending on metal market conditions and regional preferences. Units have been installed in many commodities including copper, lead, gold, PGMs, silver and nickel. Though it has been successfully employed in many operations around the world, flash flotation technology is still not well understood by many in the mining industry. This paper will discuss aspects of flash flotation flowsheet development along with some of the metallurgical and engineering considerations required to successfully incorporate flash flotation into new or existing milling circuits. This paper will also try and debunk some of the myths that exist around flash flotation cells and their operation. Case studies of flash flotation implementation will be discussed.IntroductionModern flash flotation technology was developed several decades ago by Outokumpu, with the first commercial installation of this technology being at the Hammaslahti concentrator in Finland in 1982 (Kallioinen & Niitti, 1985). This was a relatively modestly sized SK80 cell producing final grade copper concentrate directly from the flash flotation cell operating in the grinding circuit. Since that time the size and number of flash flotation cells installed globally has grown considerably to the point where today, it is a widely known application of flotation technology for amenable ores. Owing to their long history in developing the technology, Outotec are the market leader with their SkimAir range of flash flotation cells. Though there is a general awareness of flash flotation process in the mineral processing industry, there is a lack of detailed understanding of the process and the benefits it can provide to new and existing operations."

Jan 1, 2017

By Elliot B. J

Flash smelting is a complex and capital intensive technology. Although in use for 50 years the technology is still not well understood from a fundamental point of view and thus uncertainty is evident when significant change to the practice is necessitated. The application of effective design and process simulation tools has significant advantages when process change and improvement is required. Mathematical models have been used to simulate the processes occurring in the shafts of copper flash smelters. The present approach to flash furnace modelling differs from earlier work in that the burners were modelled in detail, the output from the burner model becoming the input to the shaft model. This paper serves as an introduction to the modelling process used to analyse the performance and provide a better understanding of the parameters applicable to the flash furnace at the Kalgoorlie Nickel Smelter.

Jan 1, 1992

By Tom Gonzales

At San Manuel, AZ, Magma Metals Co. operates an Outokumpu flash furnace, four Peirce-Smith converters and two anode casting wheels that are supported by six anode vessels. Process gasses from the flash furnace and converters are treated in a two-train/ double-contact sulfuric acid plant. The plant captures 98% of the sulfur. A new flash furnace was commissioned in July 1988. It has since processed more than 2.7 Mt (3 million st) of sulfide concentrate without a major rebuild. The company has gained unique experience in the operation of the flash furnace at high oxygen enrichments with low off-gas dust loadings. New procedures have been developed to maintain secondary material generation at equilibrium and for maintaining metallurgical control of operating parameters. Process flow description At Magma's San Manuel plant, concentrates and other copper-bearing material are blended and conveyed from two separate areas of the plant to three 420 t (465 st) capacity wet charge bins located above the rotary dryer. Flash furnace silica flux is conveyed to a 227-t (250-st) capacity fine flux bin located adjacent to the wet charge bins. The concentrate and flux are blended in controlled amounts and fed into a 168-t/ h (185-stph) gas-fired rotary dryer. The wet charge enters the dryer at 8% moisture and is dried to 0.2% moisture. The dried charge is pneumatically conveyed to a 580-t/h (640-stph) dry charge bin located above the flash furnace. Flash furnace charge is drawn from the bin by two drag conveyors at a concentrate feed rate of 145 t/h (160 stph). The charge is mixed with enriched combustion air and injected into the furnace reaction shaft. In the reaction shaft, the charge is oxidized to form matte, slag and a rich SO, off-gas.

Jan 1, 1992

By Petri Bryk, John Ryselin, Rolf Malmstrom, Jorma Honkasalo

THE theoretical possibilities for the realization of flash smelting have been known for a long time. Calculations concerning the same can be found in previously published literature,1 and suggestions for its accomplishment in practice are described in patents on the subject. Likewise a smaller number of practical test results are known. Autogenous smelting is closely connected with flash smelting, since in flash smelting techniques it is possible to use the heat evolved by oxidation of the sulfides for the smelting process to such an extent that under certain conditions smelting can proceed without additional fuel. However, in the event that insufficient heat is available from the oxidation of the sulfide concentrates, then additional heat may be supplied by preheating the air, using oxygen enriched air, on burning additional fuel with the concentrate.

Jan 6, 1958

By Dennis N. Poffenroth

One concern of the Mine Safety and Health Administration is the structural integrity of steel wire ropes used on mine personnel hoists and elevators. Failure of such ropes has resulted in loss of life and property. Although thorough and regular visual examinations are performed, hoist ropes may still fail from undetected internal wear, corrosion, and broken wires. To complement visual examinations, nondestructive rope inspection techniques have been developed to determine deterioration and removal criteria. The techniques use electromagnetic and permanent-magnet test instruments designed by a Canadian firm. This paper describes the operating principles, field and laboratory testing of these nondestructive testing instruments, and discusses the feasibility of using this type of testing as a supplement to visual examination and destructive tests.

Jan 1, 1983

By R. Grimard, M. Gamache, L. -P. Bigras, P. Cohen

This paper describes a real-time fleet management system for an undergroun mine. Dispatching, routing and scheduling are handled simultaneously, taking into account the mine status, operational constraints and vehicle location information. Each assignment decision takes into account the traffic on the road segments of the mine network, whether road segments are bi-directional or uni-directional, and ensures that each LHD (load-haul-dump) vehicle arrives at loading and dumping points with the correct orientation. Such a system can be used either as a simulation tool for strategic planning or as a real-time managing and optimizing system for operations. In the simulation mode, the system can accurately estimate the impact on productivity of decisions such as the development of waiting areas (bays, sidings), or the addition (elimination) of vehicles to the fleet in operation. When used for real-time dispatching, routing and scheduling of vehicles, the system can optimize production with respect to various assignment criteria such as cycle-time minimization or deviation from a target production plan.

Jan 1, 2004

By Josef Arnold, Norbert Fuegenschuh

The “Eggequerung” is an important part of the German Railway’s (Deutsche BahnAG) modernized Dortmund—Kassel line. The heart of this 13-km-long (8 miles)construction lot is the double-track Egge Tunnel with a total length of 2,880 m(9,450 ft.). The tunnel was driven using the New Austrian Tunnelling Method (NATM).The construction contract also called for a reinforced concrete secondary lining, guaranteed for a full water pressure of 30 m (100 ft.) water column. Preliminary geological study already showed that very problematic geological-hydrological conditions would have to be expected. This talk describes the chosen NATM driving concept that was adapted to the prevailing geological and hydrological conditions, the special driving method applied in geologically difficult zones as well as the water control concept used during driving. The flexibility and the limits of the NATM under exceptional hydrological conditions are illustrated. Also described are reinforced concrete lining works for the watertight secondary vault (reinforced concrete secondary lining without water-proofing membrane).

Jan 1, 2003

By D. F. Machuca-Mory

A change of support model consists of a procedure to change a stationary histogram at a small data scale to represent a larger scale; typically a distribution of sample drill-hole data is changed to represent a chosen selective mining unit (SMU) scale. Most grade variables average arithmetically. Thus, the mean stays the same for different scales, and the variance changes according to well-established theory using average variogram values. The longstanding challenge has been to predict how the shape of the histogram changes. The discrete gaussian model is widely used because it appears reasonable and introduces few artifacts; there are no artificial minimum/maximum values and the target mean and variance are reproduced exactly. The resulting distribution shape, however, is strongly dependent on a multivariate gaussian distribution. The authors generalize the approach by taking advantage of a property of the isofactorial model, which allows one to specify where the random function falls on the spectrum between a low-entropy mosaic model and a maximum-entropy diffusion model. A measure of dissemination (MD) is computed using a ratio of the madogram and the variogram. The change of support algorithm is developed that uses a variable measure of dissemination (VMD) that is easily calculated and fit to data from the deposit. The resulting VMD change of support model is very flexible to represent different mineralization styles encountered in practice; global predictions of recoverable reserves are more accurate and decision-making is improved. A number of real examples are shown to demonstrate the approach.

Jan 1, 2008

The area between Merrygoen and Digilah is located on a structural high that separates the Sydney Basin from the Great Artesian Basin, and hence the stratigraphic succession of younger rocks overlying the basement is relatively thin. The stratigraphy is briefly described and it is shown that fluvial sedimentation prevailed from Upper Permian through to Middle Jurassic times. Flint clays occur in the Permian, Triassic and Jurassic but only those in the Jurassic appear to have commercial value at present. The chemical, mineralogical, and physical properties of the flint clays are discussed.

Jan 1, 1973