Search Documents

By W. J. Birch, R. Farnfield

The use of electronic detonators to control blast vibrations has been previously established by many authors. This is performed by determining the optimum delay period between the blast holes for a particular pattern that can accurately control the firing frequency of the blast, which in turn has a direct bearing on the frequency composition of the ground vibrations recorded at a particular location. This was established by Pedgen, Birch, Hosein & Farnfield (2006) whereby like-for-like comparison tests between non-electric and electronic blasts were carried out in a limestone quarry in northern England. They demonstrated that resulting peak particle velocity values recorded at near and mid-field distances were primarily a product of the firing frequency of the electronically initiated blasts.

Jan 1, 2009

By Met M. E, Worner H. K

During the past two years, a large number of creep tests has been carried out on electrolytic lead, special assay lead and ordinary refined (Port Pirie) lead. Some of these tests have already been reported.1§ In addition, an attempt has been made to estimate the influence of the individual elements present in small traces in Port Pirie lead. The present paper gives the results obtained when small additions are made to "U" lead of the composition shown in Table 1.(which has been used throughout these investigations during the past few years). The additions were silver, antimony, bismuth and zinc. The results of the addition of tellurium have already been communicated. This investigation was intended to run parallel with a similar one using electrolytic lead as a basis and adding one element at a time.Actually, the experiments using "U" lead have got rather ahead of the others. The important point has emerged, however, that the effect of a .given addition may be appreciably influenced by the presence of traces of other elements.In most of these tests, an initial stress of 500lb. per sq. in. has been used. Whilst it is fully appreciated that this stress is higher than those used in practice, it has to be borne in mind that an improvement in creep resistance was *Manuscript received December 11th, 1936.

Jan 1, 1936

By Andy Cole

Barrick Gold recently implemented an oxygen roasting process to treat carbonaceous ore from its Goldstrike property in Nevada. One of the key project challenges was the design of the roaster gas cleaning system, which was driven by the requirements of a strict air permit and the need to achieve very high reliability. The roaster gas systems include multiple stages of wet particulate collection, a dual-alkali SO2 scrubber, mercury scrubbing, CO oxidation and NOx reduction. This paper describes the gas system, the influence of regulations on project implementation, and performance of the system.

May 1, 2002

By A. Cole, F. Porretta

Barrick Gold recently implemented an oxygen roasting process to treat carbonaceous ore from its Goldstrike property in Nevada. One of the key project challenges was the design of the roaster gas cleaning system, which was driven by the requirements of a strict air permit and the need to achieve very high reliability. The roaster gas systems include multiple stages of wet particulate collection, a dual alkali SO2 scrubber, mercury scrubbing, CO oxidation and NOx reduction. This paper describes the gas system, the influence of regulations on project implementation, and performance of the system.

Jan 1, 2002

By P Hunger, H Günter, F Heinicke

High pressure grinding rolls (HPGR) have been used for more than 20 years to grind iron ore pellet feed. Besides coarse comminution (crushing), where HPGR are installed upstream of the ball mill, there are numerous flow sheets where HPGR are used after ball milling and dewatering for re- or finish grinding.There is a clear growing interest in grinding of pellet feed with HPGR during the last few years. In addition to their known advantages of low specific energy consumption, high availability, low steel consumption and improved pelletising processes the lower environmental load (reduced or no water consumption) became a strong driving factor for the application of HPGR in pellet feed grinding.This growing demand increases the interest in better understanding of the HPGR grinding process with fine iron ore concentrates. One of the most important process parameters is the moisture content of the feed material which influences the performance of the HPGR enormously. The HPGR can react to fluctuations of the fresh feed properties to a certain degree by adjusting grinding force and roller speed. Nevertheless, there are limitations by the physics of the compression process and the capability of water absorption by the concentrate. The capability varies for different concentrates and different specific surface areas. This fact has to be considered during engineering of the beneficiation plant.The paper focuses on the influence of feed moisture content on the HPGR performance in view of throughput, increase of Blaine number and process stability on the basis of numerous pilot plant tests, modelling results and industrial experiences.CITATION:Heinicke, F, Günter, H and Hunger, P, 2017. Influence of feed moisture on high pressure grinding roll pellet feed grinding, in Proceedings Iron Ore 2017, pp 187–194 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 24, 2017

By Thibaut Pannetier, Damien Rogat, Catherine Larive, André Regnard, David Chamoley

"INTRODUCTION For several decades, the use of fibre-reinforced sprayed concrete (FRSC) has been becoming increasingly widespread, either as a replacement for or in addition to traditional reinforcements. Macro-synthetic fibres appeared on the market at the same time as metal fibres (in the 1980s), but their use has developed more recently in France, starting in the early 2000s. While their properties are attractive for underground operations, their long-term performance remains the subject of some controversy, particularly with regard to the phenomenon of creep [1-5]. Unfortunately, the many differences of protocol among the studies carried out (materials, metering, spraying equipment and test methods, etc.) mean that, in general, the results cannot be compared. Although several methods have been developed to assess the bending creep behaviour of fibre-reinforced concrete, the majority of them test notched beams resting on isostatic supports. There are currently no standardised test methods adapted to FRSC on hyperstatic supports (as is the case for FRSC used for underground support). The Asquapro association has thus developed a new test specially designed for this type of concrete. Slabs of thickness 10cm, measuring 60 x 60 cm in plan have been sprayed and tested under bending stress according to a test procedure inspired by the standardised test of energy absorption capacity (NF EN 14488-5). An experimental campaign was launched in October 2014 to study the behaviour of seven types of sprayed concrete, manufactured using the same concrete matrix: six of them were reinforced with different metal or macrosynthetic fibres and the seventh with a welded wire mesh. Fourteen slabs were sprayed for each type of concrete and also for the non-reinforced concrete with the same matrix. The types of mechanical performances measured were the compressive strength and energy absorption capacity (at seven and twenty-eight days), in addition to the creep behaviour of these seven types of concrete, placed under stress on the seventh day. This article follows on from that published in the WTC 2015 congress proceedings [6]: the programme and the test methods are briefly described here and the results available at the time of writing are presented and discussed."

Jan 1, 2016

Influence of Frothers on Bubble Shape and Velocity Close to the Generation Point

Sep 13, 2010

By Elzbieta Mielczarski, Jerzy A. Mielczarski

"It is well documented that xanthate adsorption on sulphide minerals is electrochemically controlled process. Under well controlled potential conditions the adsorption of xanthate takes place at different potential on each mineral, hence, each mineral component can be selectively separated from ore. This was demonstrated in the past for single mineral systems. In real flotation this concept never works out for two reasons: the potential of single mineral particle results from its interaction with solution as well as from galvanic contact with other particles present in the flotation pulp. Thus, the potential of a single particle results from complex surface reactions controlled by solution chemistry and the presence of other mineral particles that also interact with the solution. In flotation it is not possible to control mineral particle potential as it was demonstrated in voltametric studies of single mineral.In this study adsorption of xanthate on pyrite, galena and chalcopyrite has been investigated in the presence of those minerals. The second mineral was in solution: (i) without any physical contact with the first one, (ii) in direct contact (non-liberated grain or connected by wire), (iii) in collision type contact similar to that observed in real flotation.The adsorption of amyl xanthate on pyrite, galena and chalcopyrite was monitored by infrared external reflection technique directly on mineral surfaces. Type of the adsorbed species and their amount were concluded from the recorded reflection spectra. The presence of second mineral in solution without any physical contact does not influence adsorption. The minerals behave as if they were separated (at least during 30 min of the experiment). However, any type of galvanic contact between grains of two different minerals has tremendous consequence on the adsorption of collector on the both minerals. The detected changes are dramatic, from no adsorption to a few monolayer coverage formation.For example, pyrite that adsorbs amyl xanthate strongly in single mineral system in its galvanic contact with galena practically shows no adsorption of the collector in the same solution conditions. On contrary adsorption of xanthate on galena is tremendously enhanced during the galvanic contact with pyrite. The observed changes in the surface reactions are discussed and mechanisms of xanthate interactions in different galvanic contact are proposed."

Jan 1, 2003

Influence of Grinding Media on the Flotation of Carbonate Using Sodium Oleate as Collector

Sep 13, 2010

By Jeff R. Reinson

The Diavik Diamond Mine is producing diamonds from two orebodies, the A154 South and A154 North kimberlite pipes, discovered beneath the waters of Lac de Gras. Innovative dike technology with appropriate water collection and treatment systems allowed Diavik to start open pit mining of the ore bodies in 2002. To allow planning, engineering, and implementation of sufficient water handling infrastructure, reasonably accurate estimates of groundwater inflow quality and quantity over the life of mine are required. Prior to mining, a numerical model using the continuum approach was developed for regional and site wide water management. After approximately two years of mining, groundwater inflows to the pit were found to exceed those predicted by the base case hydrogeologic model. The most likely explanation was flow through Dewey?s Fault zone. As this fault was not explicitly accounted for in the model, a detailed hydrogeologic investigation was conducted to evaluate its geometry and hydraulic properties. A multi-disciplined approach was used and involved core logging, fluid logging, geophysical logging, packer testing, a pumping test, and water quality sample collection. The results of the field investigation were used to update the conceptual and numerical models and to develop a Discrete Fracture Network (DFN) model to address small scale problems such as flow into future underground drifts. The updated numerical hydrogeologic models predict that up to 70 per cent of the groundwater inflow to the A154 N/S open pit is through the relatively narrow fractured rock zone associated with Dewey?s Fault. Consistent with the continuum model, the DFN model predicts that inflow to a drift excavated in Dewey?s Fault will be approximately 10 times the inflow to a drift excavated in competent rock. The DFN model provides a better understanding of the distribution of these inflows on a local scale over the length of the drift.

May 1, 2006

By M. J. Raffaldi, K. W. Harris, K. A. Perry

"Highwall miners have been widely used to extract additional coal reserves from existing surface operations, particularly on contour operations in the Appalachian coalfields. Using a continuous miner cutting head, coal may be extracted from significant depths (such as 150 m), leaving behind an array of web and barrier pillars with the purpose of maintaining highwall stability. This method inherently involves elevated risks to both equipment and personnel due to proximity to and increased exposure time near highwalls. As a result, modern operations should actively design web and barrier pillars to maximize extraction while providing adequate stability. The ARMPS-HWM software, an empirical-based program created for the design of web and barrier pillars at highwall mining operations, is one such approach. The calculated stability factor is compared with empirically established guidelines produced from examining case histories.The ARMPS-HWM program is a handy tool for initial design, but understanding the site’s structurally significant geologic features and geomechanical behavior is important and may potentially increase extraction. We created a two-dimensional numerical model using FLAC3D and calibrated it to ensure pillar strength, closely following the Mark- Bieniawski formula for a typical range of pillar geometries and overburden properties. The development of pillar stresses along a highwall panel was then numerically investigated as mining progressed, and the stress distribution between barrier pillars was found to be asymmetric, which can result in an over-design of the closeout web pillars if tributary area loading is assumed. Finally, the importance of adequate barrier pillar stability is highlighted."

Jan 1, 2014

By C. M. Davidson, D. J. Drexler

"Sulphuric acid treated with hydrogen peroxide to destroy organic contaminants could conceivably show increased corrosivity toward carbon steel shipping and storage vessels, caused by the persistence of a peroxide residual. This paper describes work performed to determine the effect of 0-200ppm hydrogen peroxide on the corrosion of carbon steel by 93% and 98% sulphuric acid at room temperature (23ºC) and 50ºC.Steel electrodes were exposed to acid containing several peroxide levels (0. 45, iOO and 200 ppm) for up to two weeks. Specimens were removed at intervals and weight loss, open circuit potential, depth of metal loss and residual peroxide concentration recorded.Hydrogen peroxide decomposes considerably over two weeks in iron-contaminated sulphuric acid. initial peroxide concentrations > l00 ppm suppress corrosion, but the effect is lost when concentration decays below about 60 ppm. Sustained peroxide levels in the range below 60 ppm may increase corrosion rates. These phenomena are interpreted by analogy with anodic passivation."

Jan 1, 1987

By Anup Tiwari, Khanindra Pathak, BIBHUTI BHUSAN MANDAL

Failure of in-pit overburden dumps in open-pit coal mines causes debris to flow toward the active working face, threatening the safety of people and equipment. The evaluation of the potential mobility of failing mass will aid in hazard mitigation associated with unwarranted dump failure. The potential mobility is shown by mobility ratio (ratio of total drop between debris flow's initial and final deposition points to total travel distance) and runout characteristics. In light of above, a laboratoryscale debris flow flume was developed to investigate the effect of material gradation and slope angle on runout characteristics and mobility ratio. The total mass of experimental debris mix (Q) is fixed at 30 kg with 20% water content. Experiments at three different slope angles (30°, 35°, and 40°) demonstrate that increasing the proportion of fines in the experimental mix increases runout characteristics while decreasing the mobility ratio. The length and area of the runout decrease as the slope angle increases, while the mobility ratio increases. There is a positive correlation between d50 and runout characteristics at a fines content of 0.1Q, but a negative correlation at a fines content of 0.2Q and 0.3Q. Conversely, there is a negative correlation between d50 and mobility ratio for fines content of 0.1Q, but a positive correlation exists for fines content of 0.2Q and 0.3Q. A new index called the fine-to-coarse (F/C) ratio is used to identify the critical value of fines and coarse proportion that causes a transition from dry granular flow to fluidized debris flow.

May 29, 2023

By K. Biswas, F. C. Felipe

Paste backfill, because of its colloidal or water-holding properties, does not produce run-off water when placed underground. Paste backfill is generally, prepared from relatively low water content, full mill tailings with a certain proportion of ultra-fine particles and mixed with cement, thus producing early and better strength. Mill plant discharge tailings and other materials available at or near the mine site such as sand, aggregates or waste rock are used as blending materials in the mix design. This study investigates the influence of the above-mentioned blending materials on the mechanical characteristics of paste backfill, as well as the grading, shape, specific surface area, mineralogy and workability of the different mix design.

Jan 1, 2000

By Jorge Madias

O trabalho está baseado na análise de dados de perto de 200 fornos elétricos a arco de diferente design: convencional, de corrente contínua, de carcaças gémeas, com preaquecimento de sucata no transportador ou em shaft, etc. Incluem-se fornos que processam principalmente sucata, e fornos com carregamento parcial de gusa sólido ou líquido, ferro briquetado a quente (HBI) ou ferro esponja (DRI) a frio ou a quente. São avaliados os consumos de energia elétrica, oxigênio, gás natural e materiais carbonosos; os tempos entre vazamentos, com forno ligado e com forno desligado, assim como a produtividade horária. Com os dados obtidos, se analisa a influência dos metálicos (e seu estado térmico ao momento do carregamento), e o design do forno, sobre os consumos específicos mencionados e a produtividade.

Oct 30, 2017

By A. V. Nozhkina

"Transformation of diamond into graphite was investigated in the region of diamond metastability under the action of media chemically active relative to carbon in the temperature range from 770 K up to 2200 K and pressure range from 10-3 Pa up to 3 GPa/IV VIII group metals of periodic system and oxygen were used as media chemically active relative to diamond.Methods of electron diffraction, chemical analyses, emission spectroscopy and X-ray phase analyses were used for determination of the reaction products.It was found that in the region of diamond metastability the stage of catalytic phase transformation of diamond into graphite took place during the interaction between diamond and metal. Metal reduce activation energy for transition of diamond into graphite from 109,4 kcal/mole to 77,4 kcal/mole.Kinetic of phase transformation of diamond into graphite was investigated.Pressure does not considerably influence on the rate of phase transformation of diamond into graphite in the presence of transition metals."

Jan 1, 2003

By Scott C. Brown, Ivan U. Vakarelski

The particles commonly encountered in mineral benefication schemes have irregularites that are expressed at many different length scales. In part, this originates from preceding processes (e.g. makedown, comminution, handling and storage), which are known to chemically and physically modify the bulk particle and its surface. Interparticle tribology, dissolution and reprecipitation events along with large-scale mechanical stresses are just a handful of the interactions encountered during processing of particles prior to separation. It is feasible to imagine that each one of these events may impose a fingerprint of characteristic nanoscale, microscale, and macroscale morphological changes that can modify the overall interaction of these particles within a system. Suprisingly there are just a few works on how these resulting features can alter the performance of benefication schemes, and especially flotation.

Jan 1, 2003

By S. C. Brown

A number of studies have suggested that microscale asperities enhance bubble-particle attachment efficiency; however, in practice the roughening of particulate surfaces can also lead to a decrease in flotation. In the present investigation, it is proposed that nanoscale asperities may be partially responsible for this phenomenon. It is suggested that as inter-asperity separation distances are reduced capillary effects are enhanced leading to the formation of stable liquid domains, which adversely impact bubble-particle adhesion. In addition, obstruction of surfactant self-assembly may occur, further limiting flotation.

Jan 1, 2003

By Matti Kongas, Kari Saloheimo, Antti Remes

"The paper studies the control performance of the flotation process as a function of the measurement accuracy and sampling frequency of an on-stream XRF analyzer, using a simple dynamic model. An additional aim is to assess how the economical result of a mineral flotation process depends on the quality of process control based on the on-line elemental assays.An on-stream XRF analyzer measures the concentrations of slurry lines in a continuous cycle from several process points. The control performance depends on the analytical accuracy and sampling frequency of the concentration measurement. With a long cycle time, the state of the process changes before a new measurement becomes available. With short measurement times the statistical variance of the counted Xray pulses increases, increasing the random error in the analysis. In addition, the measurement accuracy depends on the concentration of the component to be measured from the slurry.To quantify the effect of analysis error and frequency to process control, a simple dynamic process model is created in the Matlab environment. Data from a copper flotation circuit is used as a test case. The process model comprises a first order reaction equation and the grade-recovery -relationship estimated from process data. The control was modeled using the control strategies implemented into a rule based advanced control system. The economical performance of the control was studied by calculating the overall net smelter return at various analyzer parameter combinations."

Jan 1, 2003

By F. Dehghani

The influence of different grinding methods on the shape characteristics of magnetite particles was investigated. Also, the effect of particle shape on the flotation of the magnetite, both alone and in the presence of quartz particles, was investigated. The shape characteristics of the magnetite particles were measured and calculated from images obtained by scanning electron microscopy via an image analysis system. The flotation tests were performed using a laboratory flotation cell. Results showed that in the -250+212 µm and -106+75 µm size fractions, ball mill products have a higher elongation value than rod mill products, while in the -150+125 µm size fraction, rod mill products have a higher elongation value. Particles with higher elongation values and lower roundness values have a higher flotation kinetic constant. Furthermore, the influence of magnetite particle shape on flotation is greater, and the flotation kinetic constant is higher, in the presence of quartz particles than in the flotation of magnetite alone Keywords shape, elongation value, flotation kinetics, magnetite.

Dec 1, 2013