Search Documents

By Peter de Bakker

The objective of this contract was to develop a simple, reliable, economical, remote-control roof bolting module for installation of mechanical and resin bolts. It was to be capable of placing longer than seam height bolts, up to 10 ft lengths, from a seam height of 36 to 72 in., while keeping the operator under supported roof. The resulting machine, called REM-Bolter, is a low profile unit that utilizes Foster-Miller Flexible Shaft Roof Drill, a Bendix Roof Bolt Inserter and a newly designed. Roof Bolt Lifter/Torquer. Every effort was made to strike a compromise between complete automation and complete manual control. In a controlled laboratory environment the REM-Bolter remotely installed 1000 bolts. Subsequently the machine was tested in an operating coal mine where 500 holes were drilled (and an equal number of bolts were installed) remotely, over a 4 month period. The results of all tests Live shown that the operator of a machine of this kind can quickly, and repeatedly, install rootbolts remotely from his operator compartment some 8 ft away from the drilling/bolting action. The report includes recommendations for improvements to the present REM-Bolter design that would translate the present test bed into a second generation test bed and a potential first generation production unit.

Jan 1, 1983

By T. G. Carnahan

In-place leaching is being actively utilized to extract uranium, copper, and evaporites from low-grade and difficult-to-mine ores. The purpose of this report is to discuss in-place leaching technology, its advantages and disadvantages, and to give an overview of past, current, and envisioned in-place leaching operations in the U.S.A. Application of in-place leaching to uranium ores has been particularly successful because the conditions for leaching are nearly ideal. The ores are generally in highly permeable sandstone aquifers bounded above and below by impermeable shales. The uranium ore minerals are easily leached with oxidizing acid or base solution and the pregnant solutions are amenable to ion exchange concentration and purification prior to conventional solution neutralization for recovery of yellow cake. Copper is routinely recovered from sub-grade rock by dump leaching at most major copper mines. Acidified ferric sulfate is either sprayed on the surface of the dumps or is ponded on top of the dumps. The leaching solution migrates down through the rock and dissolves copper. The solution is collected from the base of the dumps and copper is recovered by solvent extraction-electrowinning or by cementation on detinned steel cans. True in-place copper leaching is being practiced in the caved stopes of an exhausted underground copper mine. Other innovative in-place copper leaching techniques have been tested commercially and laboratory- and pilot-scale experiments have been conducted to investigate proposed in-place leaching techniques for extracting copper from difficult-to-treat chalcopyrite ores. Solution mining of evaporites is being conducted commercially for the extraction of sodium chloride and potassium chloride. A large-scale experimental project for solution mining of trona has been undertaken.

Jan 1, 1982

By L. B. Phelps

A method is presented for the burial of potentially toxic spoil in high density zones or packages within spoil piles. Such burial could reduce the outflow of pollutants and thus minimize contamination of groundwater flows. Laboratory model studies using ammonium bromide tracer were performed to quantify the expected outflow mixing that could be achieved through package construction in spoils. Field drilling and geophysical density logging of spoils was carried out at three sites in Pennsylvania and Ohio to obtain a range of field spoil bulk density measurements and spoil samples. These data are analyzed to determine the relationships between spoil density and the controlling factors of lithology, depth, age, particle size distribution and mining method. A separate series of spoil permeability tests were performed in the laboratory to investigate the relationship between permeability and its related parameters. Research results are applied to the toxic package method to suggest guidelines for pack-age size, shape, density and placement for future field prototype development.

Jan 1, 1981

By Krishna P. Sinha

An investigation was made to determine the creep behavior of oil shale at elevated temperatures. During the first phase of the investigation, work done on creep behavior of geologic materials was reviewed and triaxial creep tests on oil shale were planned. Tests at temperatures up to 250°C and axial stress up to 3000 psi were conducted at no confinement and at confining pressures equal to 1/3 and 2/3 of axial stress. Wide variations in the elastic properties as well as creep characteristics are exhibited. Creep deformation is more pronounced at elevated temperature but no definite quantitative remarks can be made regarding effect of grade of oil shale due to wide scatter and limited number of data paints. Primary creep can be described by a power law. Secondary creep seems to be an experimental function of deviatoric stress. Teritary creep was not observed within the test duration (24 hours in most tests).

Jan 1, 1983

By Thomas L. Theis

The use of a suspended growth system of T. ferrooxidans attached in a film to individual particles of bentonite and operated as a sequencing batch reactor has been shown to be a practical way of oxidizing ferrous iron in acid mine drainage. This component followed by limestone neutralization is both a technically and economically feasible approach to the treatment of these wastewaters in comparison to existing and proposed methods. The advantages, in addition to less expense, are greater safety, acceptable treatment at a lower pH, lower solids buildup, less danger of overtreatment, and greater flexibility in operational characteristics. In this report data on the continuous bench scale operation of the system under a variety of conditions shows sustained levels of oxidation in excess of 9%. A cost analysis projects capital and operating costs of $80/1,000 m3 of wastewater.

Jan 1, 1982

By Robert Torbin

The objectives of the Continuous Shaft Lining (CSL) System are to reduce the costs, safety hazards, and time currently required in lining mine shafts with concrete. The CSL will line machine bored shafts downward from the shaft collar on a continuous basis using an inverted, pressurized slipforming technique. The technique for slip-forming downwards has been demonstrated and refined under this program. The approach taken involved laboratory scale testing of key features of the CSL concept. These feature tests included concrete distribution, concrete sealing, concrete slipforming and development of a reliable concrete mix. Based on these results, a full scale above-ground test facility and CSL were designed and fabricated. The objectives of these tests were to demonstrate the viability of the basic concept; to establish operating limits; and to provide input data and information for the design of a second generation shaft lining system. The results of the program have led to a CSL design and operational philosophy which will need to be tested in an underground environment before industry will accept the technology. However, the next generation CSL promises to meet all the original program technical objectives.

Jan 1, 1983

By L. H. Wullstein

Nitrogenase activity (C2H2 reduction) was found to be associated with the following grasses in the field: Agropyron dasystachyum, Agropyron smithii, Aristida purpurea, Oryzopsis hymenoides and Stipa comata. Uptake of fixed nitrogen was also demonstrated for these grasses. Two unidentified nitrogen fixing bacteria were isolated, one from Stipa comata and one from Aristida purpurea. Cynodon dactylon and Agropyron cristatum were successfully inoculated with the unknown isolate obtained from Stipa comata. The inoculated plants exhibited nitrogenase activity (C2 H2 reduction) whereas uninoculated controls gave negative results.

Jan 1, 1982

By Gary L. Stecklein

This final report delineates the findings of the test programs, simulations, and analyses performed to determine the requirements for the effective application of berms and guardrails as truck restraint systems for elevated mine roadways. Included arts criterion for effective vehicle restraint for guardrail applications and recommendations for berm applications based on scale model tests and computer simulations. Full scale haulage vehicle-berm interaction field tests were performed to correlate the results of these model tests and computer simulations. Recommendations for the construction of berms were made on the basis of tests of berm bearing strength, response of the vehicle to different berms, and predictions based on the obtained correlation

Jan 1, 1981

By Floyd C. Bossard

Major air-cooling facilities have been installed and are operating underground in U.S. copper mines (at Butte, Montana and Superior, Arizona), South African gold mines, European coal mines, Zambian copper mines, Kolar gold mints in India, Coeur d'Alene mines of Idaho, plus other locations. Mining districts that utilize spot cooling and local air-cooling facilities would increase the above listing many times. The principal objectives of underground mine air cooling systems are to; 1. Extract heat and water vapor from the mine air and provide for their removal from the mine via (a) water pumped to surface or (b) discharged mine exhaust air. 2. Provide acceptable artificial ambient conditions for efficient working mine development and production areas. 3. Recondition used air, thus supplementing the limited mine ventilation balance. In deep South African gold mines, when rock temperatures exceed about 105°F, cooling of underground air becomes necessary for the poorly ventilated sections of the mine. By U.S. standards, air conditioning in poorly ventilated mines usually commences when the virgin rock temperature exceeds 100°F. On the other hand, well ventilated deep vein-type mines in the U.S. have been able to forego general cooling of mine air until the mines have been extended to such depths that the virgin wallrock temperatures have exceeded 115° - 120°F. It must be noted that spot-cooling of selected development headings may be required in many mines where rock temperatures exceed 100°F. Such local air-cooling practices permit the driving of long headings for exploration or extended development prior to holings which result in establishment of primary ventilation circuitry. The following summary reports on current practices of cooling and dehumidifying mine air. General system descriptions with important details will hopefully permit the reader to gain an understanding of the subject. A list of references is provided for this serious investigator who desires a more thorough knowledge-base and who is responsible for the design of a mine air-cooling system.

Jan 1, 1973

By Paul L. Michael

Roof warring signals from eleven underground coal mines (principally in the Pittsburgh seam) were studied and analyzed. The character of individual acoustic warning signals is shown to be dependent on spectral distribution of energy. Reverberation tires (pulse decay rates) were found to be usually between 0.1 and 0.5 seconds. Listening tests were conducted to assess the miner's ability to discriminate speech and roof talk signals in noise and in quiet, with and without ear protectors and with various levels of hearing loss. The ability to detect roof talk is shown to be generally degraded while wearing car protection in quiet, although, if car protectors are worn only when required by high noise levels, the ability to detect roof talk will be preserved at its maximum.

Jan 1, 1972

The purpose of the contract was to develop an improved coal mine dust sampler whose electrical-to-mechanical energy conversion efficiency would be superior to that of the presently available equipment. The electrical to (pressure) X (volume) conversion efficiency directly affects the size and weight of the air samplers. At least half of the mass of present equipment is composed of the rechargeable batteries. Any increase in efficiency will allow this mass to be reduced or the flow rote to be increased.

Jan 1, 1974

By Peter G. Groer

The commonly used exact methods (1-2) to determine the WL measure the total a activity or the total number of a counts during three preselected time periods. Due to the half-lives involved (TRaB = 26.8 min, TRaC = 19.7) I these methods take 3S minutes to complete the a activity Ra measurements. Methods using the total a counts, obtained at times less than about one RaB half-life after the end of sampling run into statistical 214 problems. These methods are almost blind to RaB (Pb214) as a consequence of its relatively long half period (see above) and the fact that RaB is a ß emitter. The way out of this dilema is to measure RaB directly through its ß activity. Since RaB's daughter Rae (Bi214) is also a ß emitter, the two f3 spectra have to be separated to obtain RaB alone. How this is accomplished 1s described in subsequent sections describing the theory of the IWLM and its calibration. 2.0 THEORY The IWLM samples air for two minutes and counts this airs ample for two minutes starting 3 sec after the end of the sampling period. The instrument has three channels. The lower a channel, the upper a channel, and one ß channel. The total RaA counts observed are accumulated in the lower a channel, the total RaC? counts are stored in the upper a channel. The total ß counts from RaB and RaC are recorded in the ß channel. These three quantities are functions of NA, NB, and NC, the unknown concentrations

Jan 1, 1975

By Klaus L. Cappel

In 1972, the Bureau of Mines of the U. S. Department of the Interior commissioned the development and design of a Simulator for research and testing of mine roof supports used in long-wall mining. The purpose of the Simulator is to reproduce forces and displacements of a section of a mine roof in contact with one or more supports. This report is an account of the design process that resulted in the final configuration of the Simulator presented here. It includes discussions of engineering considerations that led to major changes in important details of the Simulator. These changes, however, did not substantially alter the basic design originally proposed, except for the elimination of certain originally-specified features that were adjudged as insufficiently cost-effective by both the Bureau of Mines and the design agent at an intermediate stage of the design.

Jan 1, 1974

By K. J. Bathe

The current version of the computer program ADINA/BM (Automatic Dynamic Incremental Nonlinear Analysis for the Bureau of Mines) for linear and nonlinear, static and dynamic finite element analysis of mine structures is described. The complete report is divided into four parts. In Part A the program solution capabilities, the finite element library, the logical construction of the program and storage allocations are discussed. In Part B the theory and numerical techniques used in the program are summarized. In Part C brief problem descriptions and solution results for some sample solutions that have been transmitted as data cases with the program are presented. In the last section of the report, Part D, the users? manual of the program is presented. Program ADINA/BM is a general effective tool for coal mine structural analysis. The program is an extension of the computer program NON SAP (which was developed under an earlier contract with the U.S. Bureau of Mines). The important additional capabilities of ADINA/BM are: (1) the occurrence of all elements is time dependent, (2) all elements can be used in geometric and material nonlinear analysis, (3) the truss element can be used in elastic-plastic analysis, (4) the three-dimensional element can be employed in orthotropic, elastic-plastic and cracking and crushing analysis, (5) the program executes an out-of-core solution and thus allows the analysis of very large and complex coal mine models, (6) the truss elements can be employed as 2-4 variable-number-nodes elements, (7) a rock material model has been implemented, (8) displacement constraint equations can be imposed in the solution, (9) more flexibility in specifying the incremental solution strategy and an acceleration procedure in the equilibrium iteration are available

Jan 1, 1978

By Gergely Markos

Uranium mill tailings represent a potential threat to the human habitat by containing large amounts of radioactive and chemically toxic substances in high concentrations. These: undesired components enter the human habitat in various pathways such as by erosion and water or air transport. The main objective of this investigation was to evaluate the actual movement and model the potential movement of contaminants by seepage of water from the tailings into the subtailings soil. This report represents various models of the movement of contaminants using both theoretical approaches and empirical evaluation of data available from other investigations. The data consist of field measurements and laboratory determi¬nations of major and trace cations, the dominant anions, pH, and Eh of moist solids, extracts, and waters from the tailings and surroundings. Evaluation and interpre¬tation of data were accomplished by using Eh-pH diagrams, various statistical methods and the WATEQFC computer program. Data analyses show that the critical area of investigating movement- is the interfaces between tailings and the external environment. The chemical differences at interfaces seem to result in a sink system for contaminants. The tailings-soil¬-water system shows extreme complexities because of chemical and physical hetero¬geneity of the system preventing the use of a single comprehensive model to represent real conditions. The validity of the simplifying assumption used has been shown and increasing complexity has been built into the models. Analogs of these models can be used for evaluation of similar systems.

Jan 1, 1981

By Marilyn Biviano

(l)The direct economic costs to this nation resulting from a decision to embargo South African strategic and critical minerals imports are estimated at $1.85 billion per year.2,3 About 94 percent of these estimated costs are for two platinum-group metals (PGM's), platinum and rhodium. The estimated costs of a 5-year embargo beginning in 1988 for the strategic and critical minerals analyzed are presented in Table 1.4 (2)There are sufficient alternative world sources to South Africa for manganese, chromium, palladium, titanium, and vanadium to meet U.S. industrial demand in the event of an embargo. (3)Alternative world sources to South Africa for platinum and rhodium cannot meet U.S. industrial demand. Non-South African world supply sources can meet about 40 percent of domestic platinum consumption requirements and 50 percent of rhodium requirements. (4)As a result of the increase in prices for platinum and rhodium during the embargo, expansion of domestic platinum-group metals mining and secondary production is expected. During a five year embargo, domestic primary and secondary production expand and together satisfy about one-third of U.S. platinum requirements, one-third of U.S. rhodium requirements, and over one-half of domestic palladium requirements.

Jan 1, 1988

By Stan Henning

The monthly summary of the climatological record for the demonstration mine is presented in Table 1. Tear normal temperatures occurred throughout the growing season. From May to October precipitation was more than normal except in June when it was 2.55 inches below normal. Corn and soybean plantings were delayed until June 2-7 because of wet field conditions. This is about one month later than normal for corn planting. Insect infestations were much less than those encountered in previous years. Cutworm activity was not noticed and alfalfa weevil infestation were small and patchy. Stalk rot in corn was a significant problem at harvest and resulted in much Milk lodging. The wet and generally overcast conditions of July, August and September were bend 10 beneficial al to certain plant disease organisms. For example, pumpkins planted in a small garden area at the demonstration mine did not ripen because of a powdery mildew resulting from overcast, wet conditions. Field operations and row crop plantings were greatly delayed by wet field conditions. It was difficult to plant by conventional tillage because the soil remained soft and sticky where the moldboard plow had been used. Plots in the no-tillage system could he planted before conventionally tilled plots could be traversed. Plant emergence and plant density at

Jan 1, 1982

By Charles E. Glass

The purpose of this report is to demonstrate the flexibility of rte sensing techniques for providing data with which to implement mined-lands reclamation in an efficient and cost-effective manner. An operational program is presented for using satellite remote sensing data, collateral data, and automated image analysis to provide: 1) an inventory of coal and copper mines and mine waste in Arizona, 2) techniques for periodic monitoring of mining areas using multitemporal classification and image prediction techniques, and 3) delineation of high priority areas for future reclamation and current land-use planning of Arizona mining areas based on environmental hazards indices computed using classified scenes and collateral data.

Jan 1, 1980

By Fred E. Fiedler

A demonstration project investigated the feasibility and effectiveness of two management interventions, Management Training and Organization Development, for improving productivity and safety in metal/non-metal mines. The management training intervention was conducted at Texasgulf Company's trona mine, using three nearby trona mines as controls. The Organization Development intervention took place in Hecla Mining Company's Lucky Friday mine, using the highly similar Star Mine as control. The two management interventions seemed about equally effective in reducing accidents and injuries, as well as MSHA citations, and the management intervention at the Texasgulf mine also appeared to have led to substantial improvement in mine productivity.

Jan 1, 1983

By Richard Lusignea

A single boom roof bolting machine was outfitted with measurement and recording systems for detecting changes in machine parameters while drilling. The purpose of this instrumented bolter or "smart drill" is to detect changes in roof conditions from the machine parameters of penetration rate, thrust, rotation rate, torque, rejected light from rock cuttings, and vibration of the roof during drilling. The system was demonstrated underground in coal mine conditions and showed correlation between rock type and drilling parameters.

Jan 1, 1982