Search Documents

The Matakan Unit of New Ireland, Papua New Guinea is a highly fossiliferous lagoonal deposit containing numerous coal pods and lenses. The unit is strati graphically part of the massive reefal Lelet Limestone of Miocence age. These organic-rich sediments have a high hydrocarbon potential as evident from microscopical observations as well as Rock- Eval pyrolysis data. The coal is varied in regard to dominant macerals, vitrinite being predominant in some parts and pollen and spores present in sufficient proportions to constitute a cannel coal elsewhere. The highly fossiliferous carbo as Rock-Eval pyrolysis data. The coal is varied in regard to dominant macerals, vitrinite being predominant in some parts and pollen and spores present in sufficient proportions to constitute a cannel coal elsewhere. The highly fossiliferous carbonaceous sedimentary rocks associated with the coal are rich in pyrite expressed in the sulphur content (19.7 - 22.8%). A high primary productivity and anoxic sediment pore waters or just above sediment - water interface have given rise to sufficient organic matter accumulations to yield a potential hydrocarbon source rock. Atomic H/C ratios of the coals are between kerogen type III and type II mainly, expressing the mixed nature of the coal and that of the associated sediments is type II. Early generated hydrocarbons (exsudatinite) have formed from pollen exines filling the pollen cavities and in places filling micro- fissures in the surrounding vitrinite.

Jan 1, 1987

By Keith S. Olson

During 1982 and 1983, the Bureau of Mines concentrated its fugitive dust control research on haulage road dust suppression by newer chemi-cals relatively unknown in the mineral industry, innovative dust control designs for haulage trucks, chemical tailing basin stabilization, and combined chemical and vegetation tailing basin stabilization. Relatively unknown dust suppression chemicals and innovative aerodynamic modifications to haulage truck fender designs were tested on a Minnesota sand and gravel operation haulage road. Magnesium chloride salt at 95-pct control efficiency and a petroleum derivative at 70-pct control efficiency were effective in suppressing dust generated by haulage vehicles; however, none of the fender modifications were successful. Commonly used dust suppressant chemicals were tested on a Minnesota taconite tailing basin to reduce the dust lift-off during the spring and fall dry seasons. The most successful chemical was lignin sulfonate with a seasonal cost of less than $200 per acre to achieve 90-pct dust control. When chemical treatments for immediate dust control were com-bined with revegetation for permanent control, the most promising chemical treatment based on vegetation response was lime-neutralized lignin sulfonate.

Jan 1, 1987

By Alan G. Mayton

The Bureau of Mines conducted one of the most extensive studies on surface mine illumination to date, to assess the illumination needs of mobile surface mining machinery with respect to the visual tasks required of machinery operators. Field Investigations were performed at 22 surface mining operations, coal and metal-nonmetal, within several mining regions of the United States. Visibility and illumination were measured for 159 visual tasks performed by equipment operators on or near 57 surface mining machines, including draglines, shovels, blasthole drills, bulldozers, loaders, haul trucks, graders, scrapers, and several service-type vehicles.

Jan 1, 1987

By Sikko Doornbos

For the extension of the Paper Mill of Parenco in Renkum, the Netherlands, the application of a pile foundation was required. The demands for this pile foundation were very explicit a vibration free and soil displacing pile systems with low allowable settlement. Another important aspect was the total amount of piles (originally over 1600 auger piles) which had to be executed within 3 months, in very difficult and unhomogeneous soil. Based upon these conditions the Tubex Grout Injection Pile was chosen to be used for this project. This system involves the drilling of a steel tube with a conical pile shoe while grout is injected at the point simultaneously, creating a mixed-in-place layer around the tube. INTRODUCTION After extensive marketing, the board of directors of Parenco, decided to a large extension of the production capacity of its paper mill by building a new production building called Paper Mill 1 or PM-1. The new PM-1 extension had to be constructed beside the existing PM-2 because of limited terrain. The site is located right between the Rhine river and Renkum, approximately 15 kilometers (10 miles) west from Arnhem (see figure 1). The construction involved the building of the PM-1 extension of approximately 250 meters (820 ft.) long by 40-60 metres wide (130-200 ft.). The main structure was to be constructed of precast concrete beams and columns.

Jan 1, 1987

By Gooday PE, Brech GE

Ore reserve categories used by Pancontinental Mining fall into one of three fundamental groupings: Geological In Situ Reserves Mining Reserves Production Estimates The first of these describes the total reserve within stated parameters without implication as to its mineability. The second is that part of the Geological In Situ Reserve which is considered mineable under a specific mining plan. The third is the Mining Reserve adjusted with appropriate dilution and recovery factors and thus represents the best estimate of the tonnage and grade of production. This practical three category system mirrors the standard steps traditionally taken in ore reserve estimation and readily conveys the basis of the estimates. An important, but secondary classification can be added to qualify the level of confidence in these estimates using the terms: Proved (or Measured) Probable (or Indicated) Possible (or Inferred) These terms can be applied to any of the fundamental groupings, but it is generally implicit that the level of detail required to produce meaningful Mining Reserves or Production Estimates would require the basic Geological Reserve to be at a Proved or at least Probable level of confidence. The application of these classification systems by Pancontinental is illustrated by reference to the Paddington Gold Project. The methods of calculation are described including the use of geostatistics. Reconciliations of actual production with predictions from reserves are carried out monthly and annually. To date there has been an excellent correlation with Production Estimates, based on both manual and geostatistical calculations.

Jan 1, 1987

By Baczynski NR, Fagan MJ

A 3050m long section of a 1.65m internal diameter tunnel is presently under construction in the Brisbane area by means of the pipe-jacking method. The soils along the alignment had been deposited in a deltaic/estaurine environment and rapid changes in soil type occur. The tunnel passes beneath several extensive bodies of surface water. Groundwater problems have been experienced with tunnelling through alluvial sands and gravels. Details of the ground conditions, the pipe-jacking method used and tunnelling experience are discussed in this Paper.

Jan 1, 1987

By R Peden

Recent, detailed mapping, (Allibone, 1986; Peden, in prep.) of north west Stewart Island, has shown that the Rakeahua Granite (Watters et al, 1968), is comprised of a wide range of granitoid bodies ranging from diorite to leucogranite. As a result of the wide variation in granitoids Allibone (1986), suggests renaming of the Rakeahua Granite to the Rakeahua Granitoid Complex. Names were also proposed for the individual granitoid bodies mapped.

Jan 1, 1987

By Shigeru Nishitake

The Earth Pressure Balanced (EPB) shields designed by Mitsubishi Heavy Industries, Ltd., are recently more enthusiastically accepted by tunnel boring specialists. This company having built 1,000 tunnel shields utilizes its vast experience to resolve the problem to excavate through big boulders scattered in rather soft alluvial soil. Several types of EPB shields which can cope with large size boulders are described. Such shields are equipped with both drag bits and rolling disc cutters on the cutterheads. Previously removal of boulders has presented safety problems for workers while in the muck chamber, or venturing in front of the shield. This report describes the problem and how the equipment was modified to deal with the problem.

Jan 1, 1987

By Tripathy A. K, Satapathy B. K, Nayak B, Mohanty J. N, Dey D. N

The paper deals with the metallographic tudy of heat treated chromite and chromite-coke composite briquettes. The briquettes, prepared from chromite concentrate of Orissa Mines using molasses-lime, dextrinelime and tamarind seed as binders, were subjected to different temperatures and examined metallographically. The change of phase with temperature was analysed by X-ray diffraction.

Jan 1, 1987

By Birger Schmidt

INTRODUCTION Conceptual design of the first Exploratory Shaft (ES-I) for the Nuclear Waste Repository in Basalt (NWRB) began in July 1981; detailed design began in February 1982, and was largely completed by December (RKE/PB, 1983). The intent was to begin shaft construction by January 1983. The site had been prepared at that time, a construction manager selected and on board, the starter hole excavated and lined, and steel casings were under procurement. Government policy changed, however, and construction was halted before the drill rig started turning. Construction is now planned to begin in 1988. ES-I is a part of the site characterization program for the NWRB. The shaft will be used to develop production data and related information relative to drilling shafts at the site near Richland, WA, and to provide access to the repository horizon for site characterization and testing. The early program called for one shaft and some 330 m (1000 ft) of drifting. The program has since expanded to include a second shaft (ES-II) and more extensive drifting and testing. Currently, both shafts are planned to be 1.8 m (6 ft) in finished diameter, but studies are underway to determine if the second shaft should be larger. The drilling method was selected for shaft construction primarily because it offered a significantly shorter construction period than conventional shaft sinking using freezing and grouting. The finished drilled shaft will be lined with a continuous steel lining. Personnel are safer during construction with a drilled shaft than with a conventionally sunk shaft. The drilling method

Jan 1, 1987

LESLIE BRADFORD GOLDEN JUBILEE ORATION "Not only a metallurgist but a scientist of the highest order" Leslie Bradford and the Australian Metallurgical Industry

Jan 1, 1987

By G. Avolio, M. Gilbert

INTRODUCTION The city of Alexandria, Egypt is located on the Mediterranean Sea at the northwestern edge of the Nile River delta. The city is approximately 26 km long and 3 km wide bounded by the sea to the north and Lake Maryut to the south. The Alexandria Project is split into 2 phases: phase one included designs to update two existing primary wastewater treatment plants, five pump stations and over 75 km of sewer pipe, 18 km o f which is tunneled, (1500mm to 2750mm ID pipe). Currently the pipeline and pump stations are under construction. Phase two of the project includes expanding both the capacity of the treatment plants and the limits of the collection system. Included in this system expansion is the 3.5 km long, 2250mm ID Central Zone Conveyance, which is the subject of this paper. The project is under the direction of The Alexandria General Organization for Sanitary Drainage (AGOSD). It is an USAID funded joint venture of two American firms, CH2M - Hill and Metcalf & Eddy who share equally the major portion of the work and two Egyptian firms, Engineering Consultants Group (ECG) and Wairth Associates who are also partners. The venture, which is both design and construction management, worked under the name Wastewater Consultants Group, WWCG. Michael Gilbert was Chief o f the Geotechnical Department and Project Engineer for the Central Zone Conveyance. Gennaro Avolio was Geotechnical Exploration Manager for the Alexandria Wastewater Project.

Jan 1, 1987

By V. N. Rampton, C. F. Gleeson

"Exploration results over three overburden drilling anomalies defined by the Ontario Geological Survey in 1981 in the Kirkland Lake area, Ontario are presented. The anomalies come from lowland areas where overburden is thickest. By mapping the bedrock and surficial geology, by prospecting, humus sampling and shallow till sampling over the surrounding upland surfaces, one can initially evaluate such overburden drill anomalies without costly reverse circulation drilling. The drilling should follow, if necessary, only after surficial base data has been obtained. Preliminary work on these three properties has defined the presence of at least two styles of gold mineralization. One occurs in silicified zones in intermediate volcanics closely associated with northwesterly trending faults and shear zones. The second occurs in quartz-carbonate alternation zones in volcanics intruded by quartz-feldspar porphyry dykes. IntroductionThe three examples presented in this paper present first-hand information on an approach to the follow up of several geochemical anomalies that were found by the Ontario Geological Survey when they carried out reverse circulation overburden drilling as part of the Kirkland Lake Initiative Program (KLIP) in 1980 (Routledge et al., 1981). The initial approach is relatively simple, systematic, and cost and technically effective. It readies the properties for further exploration, or conversely, it could downgrade the properties as viable gold targets."

Jan 1, 1987

The estimate of an ore reserve is a vital statement made about a mineral occurrence by an evaluator. It is important that such a statement communicate reality to all groups involved in a mining project, be they technical, financial, company directors, Stock Exchanges or the public. Ore reserve statements should state both resources and recoverable ore reserves. Resources may be important in very long term considerations, (because mining, metallurgical technology and economics change with time) but recoverable reserves are todays reality. The important factors contributing to recoverable reserves (in a general sense) are geology, mining method (and its impact on dilution and ore loss), metallurgical recovery, costs and commodity prices. These all need to be reflected in the ore reserve statement. In this paper recoverable ore reserve concepts across a wide range of orebodies are considered and discussed with respect to geology, mining method and ore reserve calculation procedures.

Jan 1, 1987

By K Palmer

Alluvial platinum was recovered during gold mining operations in Maud Creek, a tributary of the Howard River. Average electron probe analyses give Pt 88.75, Fe 5.27, Ir 0.70, Os 1.06, Pd 0.34, Ru 0.14, Rh 1.29, Cu 1.06. Rare grains of a Pt-Fe-Cu alloy are also present and an unusual feature of all grains is the relatively high rhodium content which finds expression in segregations of rhodium arsenide, cherepanovite. Platinum is found in the Orepuki area of Southland, where it is probably partly derived from the mafic rocks of the Longwood Complex. Rocks of the Rotoroa Complex, similar to those of the Longwood Complex, form bedrock in Maud Creek and are possibly the source of the Howard platinum. Alternatively, it might be derived by glacial transport from the Matakitaki ultramafic block 30 km to the southwest. Origin from the Rotoroa rocks is preferred as, if the Matakitaki rocks are part of the Dun Mountain Ophiolites, they might be expected to contain osmiridium rather than platinum. The ratio Pt:Ir-Os has been widely used to distinguish low Pt:Ir-Os ophiolitic from high Pt:Ir-Os gabbroic assemblages. Mafic complexes such as Longwoods, Darran, Rotoroa, and Riwaka might be expected to show similar high Pt:Ir-Os ratios and be targets for platinum exploration. Detrital platinum examined from the Parapara area, Golden Bay is mainly osmiridium, with rare grains of rutheniridosmine, very similar in composition to that found in concentrates from the Kaniere dredge, West Coast.

Jan 1, 1987

By Robert M. Miller, Judy Milligan

A computerized "Decision Support System" was used to evaluate an "Underground Platform Approach to Oil Recovery". Over a billion calculations were required to model the mine layouts; learning curves for shaft, tunnel, and well drilling scenarios; detailed cost, schedule, and resource data; complex oil production and material balance data; varying reservoir parameters; and complex oil pricing curves. Simplified "optimum" solutions were defined in terms of muck hoisting capacity, barrels of oil per day, and present worth. Complex "optimum" solutions were defined in terms of minimal exposure scenarios during development followed by shortest time to full production.

Jan 1, 1987

By R. Pipeleers

Recent experience has shown that all underground workplaces in the Campine Coalfield in Belgium will require controlled cooling within three years. Considering the socio-economic and legal importance of the climatic problems underground, IREA has undertaken studies in forecasting the climate of future workplaces, planning the necessary cooling equipment and optimizing efficiency in the existing cooling equipment. These studies are being carried out using the climate forecasting program of Bergbau-Forschung. So far, the German model has been obliged to utilize manually measured data from a few workplaces in the Campine. As the model does not fit very well with these measurements, it has been thought necessary to' develop a system of continuous data acquisition and transmission. This system is being tested in the Beringen mine of the N.V. Kempense Steenkollenmijnen. In the first part of this paper the digital tranmission system is described; in the second the sensors used to collect the necessary climatic data are presented, and in the third some results are given.

Jan 1, 1987

This paper considers two particular empi- rical models for the processes of the generati- on of hydrochemical zoning and epithermal near- surface mineralization of mercury-antimony-arse- nic formation in the discharge area of the Uzon Caldera ore generating hydrothermal system in Kamchatka. Vertical and horizontal hydrochemical zo- ning is caused by mixture of infiltration waters of the surface formation with fluid of chloride- sodium composition which are supplied up the-zo- ne of deep fault. Ore formation is caused by simultaneous existence of two geochemical barriers, namely oxidizing and reductive. The first barrier is determined by the-level of ground waters. The second one forms under the clay-opal screen un- der the influence of two factors, namely the inflow of deep reduction sulphur compounds (which are transported together with arsenic, antimony and mercury) and the generation of hyd- rogen sulphide as a result of sulphur- and sul- phate reduction. X-ray-amorphous phase of orpi- ment composition and realgar phase are formed, respectively, on the oxidizing and reductive Barriers.

Jan 1, 1987

During the middle of this century, exploration and mining reached a low ebb in New Zealand. Tas McKee did his utmost to rejuvenate the mining industry, using the latest technology and an understanding of the environment far ahead of his time. Today, advances in the geosciences enable sophisticated exploration to proceed to the drilling stage before any significant environmental disturbance is created. Thereafter developments are now carried out with integrated management of the environment and rehabilitation so that disturbed land can be used for other purposes once mining is finished. Thus, we now have environmental engineers and scientists taking their place as professionals in our Institute.

Jan 1, 1987

By Bradley V. Johnson, Robert J. Timko, Edward D. Thimons

Water-jet-assisted cutting involves the use of a mechanical cutting bit in combination with a high-pressure water jet directed just in front of the bit tip. Such a jet can offer benefits in terms of improved cutting, reduced dust and fines, and improved bit wear. The Bureau of Mines, through a contract with the British National Coal Board, has researched the use of water-jet-assisted cutting on roadheaders. After several engineering design problems were overcome, this program led to the successful underground testing of these roadheaders. Today, more than 60 water-jet-assisted roadheaders are in operation around the world and numerous others are on order. This paper details the evolution of these machines and the benefits to be gained by their use.

Jan 1, 1987