Search Documents

By Takeuchi T, Matsugaki K

We have developed a new shotcreting which is suitable for the primary support of TBM tun- nelling in soft rock. This spraying compound is made from cement, a special accelerating agent and glass fiber. It can be sprayed on to a rock surface using a specially designed gun similar to paint-spraying equipment. Some of the characteristics of this method are as follows: 1) If spraying is done keeping the distance between the gun and the rock surface be- tween 0.2 and 3.0 m, the rebound losses are small and there is little dust. 2) This method can be used on excavated rock surfaces under inflowing water conditions of up to 10 i/m2òmin. 3) After 1 day the compressive strengthes of the sprayed material is greater than 250 kgf/cm2.

Jan 1, 1987

By Connell JE

The Worthing Mine near Hallett Cove. 20 km southwest of the cite of Adelaide, belongs to Aus- tralia's first mining era, which took place in South Australia between 1841 and 1851 (Figure 1). Oper- ations began in 1849 only six years after the com- mencement of metal mining in Australia at Glen Osmond. Although not as historically significant as Glen Osmond (1841), or the much larger copper mines of Kapunda (1844) or Burra (1845) its importance lies with its Cornish enginehouse and chimney. The Worthing enginehouse, built in 1851-1852 is the oldest remaining in Australia and certainly the most significant relic of Australia's first mining era. Six other stone enginehouses were built during that period: at Kapunda in 1848 and 1850: at Burra in 1849, 1850 and 1851; and at Tungkillo in 1849. All of these houses have long since dis- appeared although the foundations of one (Kapunda, 1850) still remain. The significance of the Worthing site is enhanced by its magnificant environmental setting in the bare, steep valley of Field River. Currently (1986) the Worthing Mine is the only site within the City of Marion which is on the Register of State Heritage Items. The site is also included in the Classified List of the National Trust of South Australia and on the Register of the National Estate.

Jan 1, 1987

By Lyman G. J

Dense medium drum separator efficiency was analysed at two Western Australian iron ore concentrators. Efficiency data had hitherto been difficult to accumulate due to the high cost of analysing representative, and therefore large, coarse ore samples. To overcome this problem, recoverable density tracers, which are in effect artificial mineral and gangue, were manufactured in three different sizes (15 mm, 30 mm and 60 mm). Their use enabled partition curves to be studied within one hour of conducting a test: separation densities were generally lower than the feed medium density for all three sizes of density tracer. For a given set of operating conditions, the smaller tracers had lower separation densities and larger ecart probab/es than the large tracers. These phenomena are explained with the aid of a conceptual model of a drum separator, which assumes that the feed ore plunges to the bottom of the drum upon introduction. Particle rising velocities are, therefore, process determining.Medium rheology was altered by adjusting the proportion of solids in the pulp. This was accomplished by changing both the pulp density and ferrosilicon/magnetite ratio. Higher solids volume fractions invariably caused a decrease in separation densities and an increase in ecart probables, most markedly for the smaller tracers. A similar response was observed when feed tonnages were raised.An explanation for these phenomena is sought in the discussion which also suggests means of improving drum separator efficiency.

Jan 1, 1987

The concept of classification in wet, closed circuit ball milling is expanded beyond the performance of the classifying equipment to include all aspects of the fines removal system of the grinding circuit. Design and operating parameters that effect fines removal are identified and discussed, and a quantitative index for circuit classification effectiveness is presented.

Jan 1, 1987

By Madgwick J. C

Powders prepared from the algae Gracilaria secundata, Ulva lactuca and Ecklonia radiatawere shown to provide sole nutritional support for microbial, microaerobic, biodegradation of low-grade manganese dioxide ore. G. secundata was the most effective bacterial nutrient giving 32 per cent recovery of Mn++, at an average rate of 63 mg Mn++/litre/day and a yield of 24 mg Mn++/g dry powder in microaerobic cultures containing 1.5 per cent (w/v)MnOz ore and 3per cent (w/v) powder over 14 days. Although G. secundata was approximately half as effective as molasses in supporting microbial decomposition ofMnOz, possible on-site growth ofthe alga could be economicaIIy more practical than transporting carbohydrate to a distant mine site.

Jan 1, 1987

By J. Molgaard, J. Masounave, J. Prinsen, P. Beaulieu, G. Huard

"A study carried out on behalf of the National Research Council (NRC) indicates that economic losses due to wear in the Canadian mining industry are in excess of $700 million annually. Severe wear, mainly by abrasion, was identified as the most important wear mechanism in terms of possible savings. One way to reduce losses would be the proper use of databases. A joint project of The Canadian Institute of Mining and Metallurgy (CIM) and NRC (Tribology laboratories at IMRI) has been initiated to create a factual database containing all relevant experience in the area of wear in the Canadian mining industry. As a first step, a prototype covering slurry pumps is being built. This should help to answer many questions, such as the number of people involved, interest from industry, cost vs benefits, etc.IntroductionTribology is concerned with the understanding of the mechanisms of friction, wear, and lubrication.Tribology is concerned with the correct use of materials for interacting solid surfaces, with the interaction of those surfaces with lubricants, with the chemistry, physics and use of lubricants and their additives. It is concerned with the reduction of friction and wear (or, in the case of belts, brakes, clutch plates, and similar devices, in achieving optimum friction with minimum wear) and is concerned with the avoidance of associated failures in machinery.Lubrication is usually the solution to a problem of friction and wear. Yet far from all the problems of friction and wear are solved by lubrication. The wear of grinding rods or shovel track pads can hardly be solved by lubrication, to name just two examples with which mining engineers will be familiar. There are indeed many situations of wear and friction where the surfaces in contact are unlubricated.In part, tribology is a matter of design. A major aspect, however, has to do with the choice of materials, to satisfy external constraints upon the component design or choice. The operating conditions for much industrial equipment, particularly in mining are, often very severe. The development of wear resistant materials, including materials which are applied as coatings, is clearly an important technology from the point of view of tribology."

Jan 1, 1987

By Kametani H

Since pyrite is a semiconductor, the relationship between the leaching rate and the semiconducting properties is of interest. In order to investigate this relationship, a pyrite concentrate (95% FeS2) was oxidized at 90¦C (363 K) in an acid solution containing 100 g/dm3 H2SO4 and 1.0 to 25.1 g/dm3 total Fe. The suspension potential (Pt vs. SCE) was maintained at the desired values, within the range 0.40 to 0.70 V, by controlled additions of a KMn04 solution during leaching. The results were analyzed using a simplified kinetic expression. The rate constant was independent of the Fe concentration, while it increased with suspension potential. Partly oxidized samples were then prepared at varying fractions of reaction. After removing the elemental sulphur formed, they underwent thermoelectric power measurements using a packed bed lying in a temperature gradient. The value of thermo- electric power increased from about 0 to 30 pV/K in the early stages of oxidation. The results obtained are compared with those for chalco- pyrite reported in a previous paper.

Jan 1, 1987

By Donald O. Capstick

A mineral survey of the approximately 144,000-acre Borah Peak study area was conducted by the U.S. Bureau of Mines in 1985 at the request of the U.S. Forest Service. The area studied included the Borah Peak RARE II roadless areas (No. 14210, 119,864 acres of land recommended for wilderness designation; and No. X4210, 18,440 acres of land recommended as non-wilderness) and other contiguous Forest Service administered land. The study area is in Challis National Forest in southeast Idaho about 30 miles south-southeast of Challis, ID. Burnt Creek, a conterminous study area to the northeast, on lands administered by the U.S. Bureau of Land Managment, was examined concurrently. Dolomite and limestone inferred reserve bases exceed 1 billion tons each within the Borah Peak study area. The material is widespread and of high quality. Extensive sampling and more detailed mapping are required to better define the resources; however, ample dolomite and limestone occur nearby, outside the study area. Dolomite is the main constituent of several geologic formations within the study area. Sample analyses indicate that the more than 1,000-ft-thick Jefferson Formation dolomite is the most pure and is equivalent to material being mined at a dolomite-to-magnesium processing plant near Addy, WA. Analyses from limestone-bearing formations underlying much of the study area indicate that large quantities of the limestone may be suitable for a variety of uses.

Jan 1, 1987

By B. J. Scheiner

The Bureau of Mines, Department of Interior, has been investigating the use of polyethylene oxide (PEO) as a flocculant for a variety of mineral wastes. As part of this investigation, the hydrodynamics of the flocculation process were studied. It was determined that to obtain optimum dewatering results, the factors of energy input into the stirrer, polymer concentration, and polymer dosage must be considered. Lt was found that at a given polymer concentration, there was an optimum stirrer speed and polymer dosage. With excess PEO, the amount of water removed in the trommel decreased, but no evidence for steric stabilization was observed.

Jan 1, 1987

By R. W. O. Kersten, J. D. Austin

A questionnaire was circulated in 1986 that had the objective of establishing the type of material that members would like to see featured in the Journal of The South African Institute of Mining and Metallurgy. The questionnaire contained five main questions involving the following:

Jan 1, 1987

By Colin C. West

On August 7, 1986, Barge 45, while being towed near the mouth of the Niagara River, was swept downstream and pinned against one of the central piers of the Peace Bridge. The barge rested against the pier with 125 feet overlying the Canadian border and 50 feet overlying the American border. The tug boat which was towing the barge was lost further downstream. Fortunately, the crew escaped and were rescued with no loss of life. There was serious concern about the potential erosion effects of the river currents on the foundation of the bridge pier as caused by the flow concentrations around the barge structure. Due to the time of year, with the approaching Fall and associated worsening weather conditions, it was imperative that the barge be removed as soon as possible. Donjon Marine of New Jersey, the United States Navy's Atlantic Zone Contractor, was called on to retrieve the barge. By this time the original owner had abandoned the wreck.

Jan 1, 1987

By W. C. Smith

This Bureau of Mines report discusses how pull-test data can help establish polyester resin column length criteria for roof bolts in evaporite minerals. The study evaluates the effectiveness of partial to full columns of resin in anchoring 4-ft, No.6, grade 40 rebar roof bolts in potash, salt, trona, gypsum, and borate mine roofs. Pull tests were performed on over 600 roof bolts in 11 evaporite mines. Column lengths ranging from 6 to 48 in (fully grouted) were evaluated for each test site. In general, comparative results among all test sites indicate that pull-out loads in excess of 10 tons (force) were attained with resin-grouted bolts having 13 to 75 pet less than a full column of polyester resin. Ten tons (force) of load-carrying capability compared favorably, in terms of strength, with the calculated yield strength of the rebar used in the tests, which was 8.8 tons (force). The site-specific nature of each test site, due to the unique combinations of geology, mine-induced stresses, and other unknown parameters, prevented the establishment of valid generic column-length criteria. For these reasons, data to evaluate resin-column-length effectiveness are best obtained on a mine-specific basis.

Jan 1, 1987

By A. F. van Weele

In general cast-in place piles will have an irregular pile shape. However, it is possible that these irregularities are so large that they may lead to pile deficiencies. It is very rarely possible to examine the pile foundations visually. Also the performance of a static or dynamic load test on each individual pile is not practical and much too expensive. This is the reason why pile integrity tests have been developed: to reduce the risk of inadequate pile foundations by performing a simple test. Pile integrity tests are non destructive tests which are carried out after a pile has been installed. Over the years a number of techniques have been developed of which the most important techniques are briefly described in this paper. Of all pile integrity testing methods, Sonic Integrity Testing is the most widely used method in western Europe. This method has been developed by TNO some 15 years ago. Since then the method has been improved, largely due to advances in micro-processing. A major improvement was made by the introduction of digital signal processing techniques. This made the Sonic Integrity Testing method more accurate (smaller defects can be detected), faster (more than 200 piles can be tested on a single working-day) and more reliable (the results are easier to interprete). A few cases will be presented which will show the usefulness of the Sonic Integrity Testing method. In one of these cases, a helpful tool for interpretation of the results is explained: the Sonic Integrity Testing Simulation program TNOWAVE. Notwithstanding the fact that Sonic Integrity Testing is a powerful method, it has also some strict limitations. These will be discussed at the end of the paper.

Jan 1, 1987

By Thompson AG, Cadby GW

The New Austrian Tunnelling Method (NATM) is a proven concept for the safe and economic construction of underground facilities. This is especially true for tunnelling activity where changing ground conditions are often encountered. However, the principles central to the NATM have gained only limited use within Australia, presumably due to the measurement process inter- fering with tunnel driving and the cost associated with instrumentation and interpre- tation expertise. The design and operating principles of two basic instruments are explained together with laboratory simulated test results and suggest- ions for use in an integrated NATM style approach to underground excavation and construc- tion. The two instruments monitor load in rock reinforcement and deformation in rock or primary and secondary linings. The instruments may be fitted with a miniature display module which outputs the measured parameter in engineering units directly. The design of the sensing components allows the instruments to be installed in various configurations suitable for routine performance monitoring, quality control, support element testing or detailed investigations. The display module which reduces the need for instrumenta- tion expertise should suit contractors and allow performance data to be obtained which quickly may be used to modify support procedures to suit ground conditions. When complemented by convergence measurements the devices enable most facets of the NATM to be implemented.

Jan 1, 1987

A critical appraisal of the wide variety of processes used in the pyrometallurgical production of metals and non-metals shows that there is a strong physico-chemical and, in particular thermodynamic, basis for the variety. Based on this, a simple classif- ication scheme has been developed which makes it possible to understand the methods for extracting individual metals and non-metals pyrometallurgically and to assess which are the more attractive routes. The analysis presented shows why there are essentially two broad routes for pyrometallurgical production of metals and non-metals; viz., the reduce- refine and the refine-reduce routes. Halides have the role in pyrometall- urgical processing of producing pure compounds for subsequent reduction. The criteria which determine the selection of reduction method for oxide raw materials and intermediate halides (e.g., use of carbon, hydrogen, a more reactive metal or electrowinning) are examined critically in the paper. The treatment of sulfide raw materials is considered also, particularly the criterion for smelting sulfides directly to the metal.

Jan 1, 1987

By Sowerby BD

The CSIRU Division of Mineral Engineering is developing various techniques for the on-line determination of moisture in coal and coke, and some instruments are now commercially available. These techniques permit accurate and rapid determination of moisture in materials directly on conveyor belts or in bins. The most promising techniques for direct on-belt measurement of moisture in coal are capacitance and microwave transmission. A non-contacting under-belt capacitance and gamma-ray backscatter technique has determined moisture in coal to better than 0.5 wt'/. in field tests at BHP Stockton Borehole Colliery, NSW. Mineral Control Instrumentation Pty Ltd have been licensed to manufacture the capacitance gauges and have installed five commercial units in the coal industry and other industries. Microwave transmission techniques have an advantage over the under-belt capacitance technique in that they are not sensitive to vertical segregation of moisture in coal on the conveyor belt. A laboratory prototype of a microwave transmission gauge has been constructed and tested. Microwave techniques, based on a measurement of attenuation and phase shift, are under development and are expected to be field tested in 1987. These new techniques will enable a wide range of thickness changes to be accommodated. Capacitance and microwave transmission methods are unsuitable for materials of high electrical conductivity, such as coke. CSIRO is therefore developing a fast neutron and gamma-ray transmission technique, which is proving very accurate in laboratory tests. This technique overcomes many of the limitations of thermal neutron moisture gauges and it is expected to be field tested in 1987.

Jan 1, 1987

By Ron Robinson, Trevor Harrison

The planning, installation and commissioning of the first scheme of controlled recirculation of air flow in a section of coal mine in Great Britain is described, together with the proposals for a second installation. The work updates a previous paper (Robinson and Harrison, l986) on the subject. The special problems of ventilating the increasingly distant faces of the undersea mines in the North East Area of the British Coal Corporation are discussed and the alternative solutions stated. The advantages of using a system of controlled recirculation of air are proposed together with the safety features considered necessary. Design and installation details of the recirculation fans and a new booster fan are described.

Jan 1, 1987

The elements of consistent structural de sign models for underground structures are explained. Such models should comprise at least ground properties, excavation and support methods, computational models for analysis, failure hypotheses, and in-situ monitoring. The fundamental characteristics of the interaction between ground and support are investigated. Then, plane strain models for soft ground tun- nelling and design models for rock tunnelling employing stress release at the tunnel face are elaborated. Some numerical evaluations are gi- ven in diagrams, comparing approaches of dif- ferent authors. Comments are presented on nume- rical three-dimensional models (visualized by structural models for mining in rock salt), on the interaction of in-situ monitoring and design, on structural safety for underground structures, and finally on the general develop- ment of structural design models in geo- Techniques.

Jan 1, 1987

This paper briefly discusses the negotia- tion of the more important provisions in agree- ments for exploration and mining rights with Pacific countries. LAND RIGHTS Land rights are complicated and sometimes controversial in many of the Pacific countries. In some countries, a company will have to deal with land owners directly; in others, the government will act as intermediary. Inevit- ably, a company will have to deal with both. Mining companies need to be sensitive to the culture and particular interests of the land owners and of their history in defending their rights. The issues are too complicated to be dealt with here. Some mining companies have spent, and will continue to spend, considerable time trying to understand them. It will " require patience, perseverance, sensitivity and unflagging optimism. The better advised companies will ensure that their local repre- sentatives get to know the land owners, under- stand their concerns, and will pursue a policy of keeping them informed on a regular basis of all of the company's activities and proposed activities. Good community relations are the keystone for good mining operations in the Pacific. Most countries will require the submission of an environmental impact statement so that they will know in advance what effects a pro- posted mining operation are expected to have on the environment and how it is intended to deal with them. They will also want to approve the company's environmental reclamation and rehabilitation plan. Let's face facts right away - mining, by its very nature, is not going to improve the environment. There will be waste discharges, emissions and deposits. They will affect the land, air and water and hence human, marine and animal life and vegetation. There will be sounds and odours and the esthetics of mining operations, though perhaps pleasing to geolo- gists and mining engineers, will not please Others.

Jan 1, 1987

By Dennis P. Bryan

The southwestern United States has an abundance of natural lightweight aggregate (NLA) deposits of volcanic origin that are being used in the construction industry within the region. New Mexico, Arizona, Nevada and California utilize NLA in portland cement concrete and concrete masonry units for weight reduction and related economic reasons. The geological environment of the western United States is amenable to the occurrence of natural lightweight rocks because it contains Tertiary and Quaternary volcanic products that include low-density glass and vesicular material. There are two major classical types of natural lightweight materials of igneous origin; pumice and cinder. These account for the vast majority of volcanic rocks that are presently utilized as NLA. Pumice is an ejecta product generally found as part of tuffaceous units associated with nearby siliceous volcanic centers. Cinder, also an ejecta product, is associated with mafic volcanics and is most often found as a cinder cone. Both are highly vesicular. A third type of natural lightweight material, though also associated with siliceous volcanics, is less vesicular than pumice. It is best described as being a slightly pumiceous rhyolite or rhyolite-tuff breccia that occurs as a siliceous dome or tuft unit that is most likely to be glassy. Uses of these natural lightweight rocks center on the construction industry where they are utilized in lightweight portland cement concrete and lightweight concrete masonry units. The major reason for usage in portland cement concrete is cost saving effected by weight reduction in high-rise construction. The major usage in concrete masonry units, or "block", is for weight reduction that enables a mason to lay more lock.

Jan 1, 1987