Search Documents

By Chris Lynagh, Collin Schroeder

Determining the best excavation method is a critical step in successful tunnel construction. In rock tunneling, several factors can dictate the excavation method, such as: (1) rock characteristics, (2) tunnel size and length, (3) nearby utilities/infrastructure, and (4) contractor’s preferred means and methods. This paper discusses the various rock tunnel excavation methods utilized on the Doan Valley Storage Tunnel Project (DVT), a project constructed as part of the broader Project Clean Lake in Cleveland, Ohio. The differences between each method’s initial and final lining, geology, and cycle sequence will be analyzed and compared.

Jun 13, 2023

By Donald W. Gentry

This paper presents some of the results of a rock mechanics in¬strumentation program designed for, and implemented at, longwall panel 4N at the York Canyon Mine near Raton, New Mexico. The objective of this particular instrumentation program was to determine the response of the rock mass to longwall mining of a thick coal seam utilizing shield-type supports. Measurements were made in the rock along the ground surface, above the coal seam, in the coal seam and immediately below the coal seam. Longwall test panel 411 had a total developed length of 762 m (2500 ft) and a face width of 168 m (550 ft). The seam mining height in the panel area was approximately 3 m (10 ft). The average depth of overburden above the panel is 107 m (350 ft) al¬though it ranges from 73-134 m (240 - 440 ft). Roof support at the face was provided by Hemscheidt shields. These shield-type supports weigh 11.4 metric tons each.

Jan 1, 1977

By Stephen H. E. Phillips

This report outlines the modifications that have been carried out to the original prototype rectangular shaft sinking equipment for its use in a circular shaft. The surface testing of the machine is described where seven, 24 ft. diameter shafts were excavated to an average depth of 21 ft. at rates ranging between 1 ft/hr and 1.9 ft/hr depending upon the prevailing conditions. The durability and productivity standards for the equipment were established indicating that the objectives of the project had been realized. That is, when using the machine the sinking rates could be increased by 25% and costs reduced by a corresponding amount compared with conventional drill and blast methods. In addition it was shown that the machine had been developed to a state of fitness for sustained underground use.

Jan 1, 1981

By B. Clermont

Ball mills are usually the largest consumers of energy within a mineral concentrator. Comminution is responsible for 50% of the total mineral processing cost. In today?s global markets, expanding mining groups are trying to optimize mill performances. Since comminution is concerned with liberating valuable minerals for recovery in the separation process, it is crucial to run the mills at the best operating conditions which lead to good liberation at competitive throughputs with minimum costs (energy and wear). The high availability of the equipment is also essential to maximize production and profit. To reach this key objective, continuous and reliable information about the mill operation is vital. An innovative tool which can deliver information about in-mill dynamics has been developed by Magotteaux. It can provide online and accurate measurements of the degree of grinding ball fill and pulp position for timely decision making and actions. This tool could be used on its own or linked to an automatic grinding ball loading system named Magoload. Therefore, ball load could be kept constant by using direct measurement. This article describes the Sensomag and presents some of the major improvements that can be achieved with it. Some other promising avenues are still to be explored. Keywords: Comminution, process control, process optimization, process instrumentation, online analysis.

Jan 1, 2010

By P. H. Carr, G. G. Marino, K. A. Patel

Extensions to a correctional institution at Wabash Valley, Indiana, required development over abandoned coal-mine workings, at 90 m depth, where subsidence was possible at surface. Backfilling of the flooded mine in critical areas was determined to be the most cost-effective method of limiting the risk of damage to the buildings. Containment grout was first placed in selected entries and cross-cuts of each mine area; the remaining volume was then filled with a readily flowing infill grout. Where a high proportion of an area was taken up by rubble, calcium lignosulphonate was used as a retarder and plasticiser to increase penetration. Grout movement was monitored from adjacent boreholes with an electrical resistivity probe during grouting, while after the work was finished core samples were obtained from verification holes drilled in the backfilled areas

Jun 19, 1905

By L. J. Terrill

Lateral displacement in the immediate roof beam at the Waste Isolation Pilot Plant (WIPP) is a significant factor in assessment of excavation performance for the design of ground control systems. Information on roof beam lateral displacement, expansion, fracture formation, as well as excavation convergence, is gathered using a variety of manually and remotely read instruments. Visual observations are also used when possible. This paper describes the methods used to measure lateral displacement, or offset, at the WIPP. Offset magnitudes are determined by the degree of occlusion in drillholes that intersect the offset plane. The Borehole Lateral Displacement Sensor (BLDS) was developed for installation at WIPP to monitor offset at a high degree of accuracy at a short reading frequency. Offset measurements have historically been obtained by visual estimation of borehole occlusion. Use of the BLDS will enable relationships between time dependent roof beam lateral displacement and expansion to be established in much shorter periods than is possible using visual observations. The instrument will also allow remote monitoring of roof beam displacement in areas where visual estimations are not possible. Continued monitoring of roof beam displacement, convergence, and expansion, is integral to timely and pertinent assessments of WIPP excavation performance.

Jan 1, 1996

Power Plant. The power for the metallurgical operations is supplied by the company's own power plant, which is centrally situated. Power is also supplied to Metal Manufactures Ltd. and Australian Fertilizers Ltd., both being adjacently situated to this company'sworks.The power supplied is direct current, 250 volts, and is obtained from direct-current generators coupled to turbines and to Belliss & Morcom triple expansion engines.The steam supply is obtained from Babcock & Wilcox water tubular boilers, the fuel used being drawn from the South Coast coal mines.Transport. - The works are connected by standard broad gauge railway to both the jetties and the Government railway. Two steam and three electric locomotives are employed in this service.In addition to its own requirements, transport is provided to Metal Manufactures Ltd. and Australian Fertilizers Ltd.The various operating departments are connected by a 2-ft. gauge railway operated by Jeffrey electric locomotives.Ore Storage and Sample Mill - These departments are connected by broad gauge line to the Government railway and jetties. All material which is railed or shipped to the works from the various centres is weighed, sampled and placed in the ore store, or outside gantries, before being treated.Since the whole of the material received is either purchased or treated on a toll charge, great care is necessary in the weighing and sampling of all the receipts.Assay Oflice--The assay office is divided into several laboratories, where analyses of the various purchased materials and works samples are carried out.

Jan 1, 1938

By C. Sawmliana

Deep-hole blasting operations in opencast mines are always associated with some annoyance to the surrounding areas in terms of ground vibration, noise, flyrock, etc. These become more severe when underground mines run parallel to them. Blasting in opencast mines may pose danger to the underground mines in terms of roof/side failures, damage of water dams, isolation/ventilation stoppings and other underground installations. The paper discusses a case study in India on the impact of deep-hole blasting in Ramagundam Opencast Project ? III on the stability of various water dams of GDK-6B Incline coal mine operating in close proximity. The stability of underground water dams of GDK-6B Incline mine was endangered due to deep-hole blasting at OCP-III. There were 15 water dams in seam 3 and 16 dams in seam 4 of the underground mine. The physical strength tests using a Schmidt Hammer instrument were carried out in all the 15 water dams of No. 3 seam and 16 water dams of No. 4 seam. The test revealed that there is a decrease in compressive strength values of three dams of seam 3, namely 6A, 6B and 7. Theose three dams were also directly connected to the water source. Water seepage was also observed from the surfaces of the three dams. However, they were found to be stable in accordance with their design parameters and damage point of view while considering a threshold value of ground vibration as 25 mm/s. It was found that the value of tensile stress generated by a vibration of 25 mm/s was much lower (i.e. 0.171N/mm2) than the tensile strength of the two weakest concrete dams (1.85 N/mm2). Ten experimental blasts were conducted at different working benches of the opencast mine and the ground vibration data were recorded in roof and pillars near various underground water dams. The maximum value of vibration data recorded was 5.9 mm/s in roof near dam no. 1 in seam 3 with the dominant peak frequency of 22 Hz. No adverse effect on either of the dams was observed after that blast. During the period of study, no deterioration/adverse impact was found in any dam of the mine. Based on the results of the study and the analyses of the data, optimized blast design parameters and explosives weight per delay were suggested for the opencast mine to maintain the safety of the underground water dams. Keywords: Opencast blasting, damage, water dams, underground mine, ground vibration

Jan 1, 2009

By Raphaël Mermillod-Blondin, Claude Bazin

"Sampling is an important step for ore body evaluation and daily plant material balances. The Gy’s equation is regularly used to assess the size of the samples to be collected and to estimate the reproducibility of the collected samples. The equation works well for iron and base metal ores but seems to produce pessimistic estimates of the gold content reproducibility for gold ores. A model is proposed to simulate the division of samples using a standard splitter and discrepancies are observed between the Gy’s equation predictions and simulated samples reproducibility for crushed gold ore. Results of the simulation show that sampling a pile of ore crushed to -2 mm should lead to more reproducible gold content than it is observed in practice and predicted by the Gy’s equation.INTRODUCTION With current gold prices above $1400 per troy ounce operators seek for new economical ore bodies. The metallurgical evaluation of an ore body is one of the numerous steps required to justify the investment for the development of a gold mine. Metallurgical testing requires to sample the ore body and to prepare the ore sample for the grinding and separation tests. The preparation implies crushing the ore usually to less than 2mm and its division into batches of a given weight for subsequent processing. For gold ore testing a batch of crushed ore is ground in a laboratory mill and leached using cyanide. Gold recovered in the solution is used as an indicator of the ore processing amenability. One difficulty associated with ore testing is due to the reproducibility of gold content measurements of the feed sample. According to the Gy’s equation (Gy, 1979; Morisson, 2009) the division of a 20 kg batch of -2 mm ore containing 5 g/t of gold into batches of 1 kg may lead to batches containing 5 ± 5 g/t of gold. For this reason the gold content of a feed sample is usually back calculated from the assays of the solution and solids residues of the leaching process. However, these two assays may contain measurement errors that can propagate through the calculation of the gold recovery. The use of the feed assays as a redundant information could add robustness in the evaluation of ore amenability to processing. This paper discusses the problem of sampling reproducibility for a gold ore. The analysis is carried out with reference to the Gy’s equation for the sampling of particular materials."

Jan 1, 2012

ON mineral lease 38 of the Sulphide Corporation Limited, Broken Hill, a shaft was sunk in the early days Ior prospecting purposes and at the present time it is accessible as far as the 1000-ft. level where a connexion exists with the main workings of the Corporation's Central Mine, mineral lease 9. About the year 1895· a crosscut was driven east from this shaft at the 1330-ft. level cutting the Central Ore-body in mineral lease 9 and the shaft is supposed to extend a further depth of 25 ft; but no records of any of this work are in existence, the whole of the evidence being based on hearsay and memory:Fig. 1 shows the position of the Extended shaft in relation to the main workings. The shaft filled with water to the 1000-ft. level where it overflowed through the crosscut to the main shaft and was pumped to the surface, but when the South drive on the 1300-ft. level was pushed to the southern boundary, it was deemed advisable for safety, to tap the water at this level and so relieve the...

Jan 1, 1919

By V. R. Spironello

The Bureau of Mines is involved in research directed toward the utilization of municipal solid waste. One of the primary objectives is the recycling of the magnetic fraction of municipal solid waste (raw refuse). This is consistent with one of the Bureau's goals, which is to minimize the requirements for mineral commodities by maximizing metals recovery from secondary domestic resources, In this investigation, cupola trials were made using combinations of refuse scrap with shredded automobile scrap under basic and acid slag practices. Furnace operating information and the behavior of alloying and tramp elements was obtained. The research showed that it is possible to utilize up to 60 percent refuse scrap in the cupola under basic practice and 30 percent under acid practice, Aluminum in refuse scrap, present in bimetallic cans, increased the recoveries of silicon and manganese charged to the cupola. Increased use of refuse scrap provided iron of lower sulfur. The alumina resulting from oxidation increased the slag volume. The aluminum and tin contents of the iron increased with increasing levels of refuse scrap in the charge. Lead was not a problem with respect to contamination of the iron. In basic practice, operation of the cupola was satisfactory since all slags were adequately fluid. In acid practice, operation became troublesome above the 45-percent level. Under both practices, the cupola iron melting rate decreased. Particulates in scrubber water and stack condensate samples contained lead, zinc, and tin, and the dust load increased. The tensile and transverse strengths of the iron produced under both practices are reported.

Jan 1, 1980

By Z. Yu

Low-rank/oxidized coals respond poorly to oil agglomeration. Emulsification of kerosene in the presence of surfactants dramatically reduces the size of the kerosene droplets. While this dramatically reduces the amount of oil that is required for efficient agglomeration (down to 0.25-0.5%), more importantly, the surfactants entirely change the electrokinetic properties of the oil droplets and thus the interaction between oil droplets and coal particles. Consequently, kerosene cationic emulsions can efficiently agglomerate oxidized coal particles. The agglomerates obtained in such a process can still be recovered by screening. Surfactants can affect fine coal filtration very profoundly when used to emulsify the oil which is utilized to agglomerate coal prior to its filtration. This sequence is much more logical than the use of flocculants - highly hydrophilic polymers - as filtration additives to aid dewatering of flotation concentrates. Although such polymers flocculate coal particles, they also render coal surfaces hydrophilic and make reduction of the cake moisture content difficult.

Jan 1, 2000

By Ruth F. Brinkley

This report is the 18th of a series of reports originally issued annually, and more recently bienially, to acquaint the public with the work of the Federal Bureau of Mines in explosives technology. Part I reviews briefly the overall activities during fiscal years 1957 and 1958.4/ Part II presents in abstract form the publications prepared by the Bureau that appeared during the period.5/

Jan 1, 1961

By Kenneth H. Johnston

This publication describes a thermal-recovery project and two waterflood projects in Carter, Garvin, and Stephens Counties, Okla., that will be visited during the 1966 annual tour by the Bureau of Mines in cooperation with the Kansas-Oklahoma Waterflood Association. Among the unique features of the projects arc (1) the movement of heavy (15° to 28° API gravity) crude oil through the reservoir and into the well bore with energy furnished by burning a portion of the crude oil therein; (2) the use of an inverted nine-spot pattern with dually completed injection wells, to produce oil from deep (8,200 to 10,200 feet) reservoirs; and (3) the flooding of five sand lenses separately by using controlled water injections through multizone completed injection wells. Discussion of the individual projects includes information on their early history, method of completing and operating wells, source and treatment of injection fluids, oil production decline curves, and the results obtained from the development.

Jan 1, 1966

By J. A. Lamonica

The Bureau of Mines conducted an environmental noise survey to determine the noise levels to which underground coal mine employees are exposed, to evaluate noise survey techniques and equipment, and to compare noise exposures using two criteria, Walsh-Healey and CHABA, for determining allowable exposures that were under consideration for the Federal Coal Mine Health and Safety Act of 1969- Time study techniques and Bureau-approved standard sound level meters were employed. The shift exposures of 20 percent of the miners studied were in excess of the safe standards established by both criteria. The shift exposures calculated using the Walsh-Healey criteria were greater than those calculated using the CHABA criteria owing to the intermittent nature of the exposure. Ultimately the CHABA criteria were rejected, and the Walsh-Healey criteria were adopted.

Jan 1, 1971

By Larry Schneider

Are you one of the thousands of hunters, fisherman, or hikers who purchased handheld GPS systems over the past several years and then been disappointed in their accuracy and performance. Or maybe you are one of the hundreds of blasters who have attempted to use GPS as a method for locating the exact position of their blast and measure distances from the blast to nearby structures. If so, you may have found that the accuracy of the handheld GPS systems left much to be desired. It may be time to get the units back out of storage and give them another try. As of midnight, May 1, 2000, the federal government has turned off the “error” built into the system known as “selective availability.” Here is a brief explanation of what that means in a question and answer format.

Jan 1, 2001

By David Mitchell, Daan Delport, Frik Marx, Mike Shapiro

The use of copper cooling elements to enhance refractory lining life in pyrometallurgical vessels is common in modern furnace design. Copper elements typically incorporate a base panel with cast in cooling passages and an integral extended surface (formed of pins, fins or similar) onto which suitable refractory material is cast. The metallic, conducting parts are located towards the cold face of the lining, with the refractory material interposing between the coolers and the process. The coolers are designed to arrest wear of the refractory material by freezing a layer of slag or partially reacted material onto the hot face, thereby rendering the lining inert to further attack [1]. These coolers have achieved success in new furnaces and relining of existing vessels. The freeze layer is prone to mechanical damage during operational and process instability. The coolers must be capable of extracting the additional heat flux under upset conditions to facilitate rapid self-repair of the freeze layer and prevent further refractory wear in the intermittently exposed areas. However, operational experience has shown that the high heat flux capabilities of the copper coolers have some disadvantages, especially in processes producing vapours which form corrosive compounds when condensing onto the cold surfaces of the coolers. When corrosive conditions develop, the entire composite will fail due to loss of structural integrity, and as a result of leaks from the cooling water passages. This paper describes recent developments in the approach to the design and manufacture of copper cooler panels customized to achieve specified heat fluxes and temperature profiles, thereby reducing the formation of corrosion mechanisms in applications with corrosive gaseous environments and enhancing refractory lining life. Condensation formation prevention is achieved by adjusting the geometry of the cooler and selection of suitable materials of construction.

Jan 1, 2007

Gold was first discovered in the Shotover by Thomas Arthur in 1862. He left his job as a shearer and soon there were up to 3000 miners working over the length of the river. Some parts were extremely rich and a few early miners recovered as much as 300 ounces in a day. From these early days of hand working the operations progressed through to hydraulic elevating once water races and pipes were installed after the Skippers road was completed about 1890. The riverbed was worked in paddocks with .the gravel being sluiced to a central suction which elevated the material over a sluice box. Use of this system continued intermittently through until 1977 when Joe Schieb retired û the last of the hydraulic miners. Many bucket ladder dredges worked on the lower Shotover near Big Beach where the Sew Hoy family recovered a lot of gold. Just after 1900, at least three worked further upstream, one on the beach where Shotover Jet now operates and one further up below the Moonlight. All the sections for this were transported in over the Moonlight Track and the boiler, steam engine and bucket ladder are still sitting at the edge of the river. up near Maori Point a dredge operated from Dredge Slip upstream. Records are poor on these dredges but they all suffered from the frequent floods and large boulders which damaged the bucket line. The last dredging attempt was about 1930 when a suction dredge was constructed on Maori Beach. This failed as seems to be normal for most suction dredging ventures. The river can drop to very low levels in the middle of a dry summer, and in winter when the water is tied up in the mountains as ice and snow. During 1863 when heavy rain melted snow in the high country, the river rose 35 feet overnight and drowned many miners camped on the banks. The ever present risk of flooding dominates the method of working and plant design.

Jan 1, 1987

By Robert Morgan

With improved methods for designing and detonating shots the potential for flyrock can be significantly decreased, but there are few absolutes in blasting; therefore blasters must learn from the mistakes of others. Blasters must conscientiously employ control measures to minimize the risk of flyrock. The worst case incidents which tend to be widely reported by the media, should serve as a reminder to us all that minimizing the risk of flyrock must be incorporated into the design of the drill pattern and blast design.

Jan 1, 2001

ONE of the phases of mining wide ore-bodies, such as are found in Broken Hill, is the laying-out and design of the sill floor gangway timber, When, in the above operation, a detail has to be repeated frequently, it is desirable in the interests of efficiency that that detail should be standardized as far as possible. Before arriving at a standard design e.g., a crosscut layout-it would seem necessary to compare its strength with some other unit of timber and see that the general design is at least as strong as the unit that has been taken for comparative purposes, In these notes no attempt is made to calculate the stresses to which timber underground is subjected, but merely to draw a comparison between the relative strengths of the various cross sections of timber in common use underground.It has been assumed for the purposes of comparison that the milling exerts pressure in a vertical plane only, and is uniformly distributed over any area. A beam supported at both ends, and with a uniformly distributed load, has the maximum bending moment at a point midway between the points of support, and equals- WL2 8 where W = load per unit length. L = distance between points of support.The bending moment also equals M-, where y M = modulus of rupture of the material in question. I = moment of inertia of the section of the beam about a given axis.Y = distance of extreme fibre from that axis. WL2. I The formula -8- = MY- only holds good until the elastic limit...

Jan 1, 1923