Search Documents

At Copper Refineries Pty. Ltd., Townsville, two reverberatory furnaces of 420 tonnes capacity are used to melt 210000 tonnes/year of copper for subsequent anode casting. When the refinery commenced production in1959, these furnaces were of 300 tonnes capacity. The original furnaces featured a silica brick hearth, magnesite and chrome magnesite side 'walls, and a sprung silica brick roof, but were unsatisfactory because of thelow refractory life and high costs. With continuous expansion in production and the incentive to increase furnace life and capacity the design of these furnaces has changed greatly since that time.The present furnaces feature all basic brick, a flat suspended basic brick roof, very extensive use of watercooled copper sections, and are of substantially increased (420 tonnes) capacity. Particular attention has been concentrated on high wear areas such as the taphole, side walls, and charging door jambs. Each furnace in its 24 h cycle, is charged, the copper melted, impurities skimmed off, metal "poled" prior to casting, and cast.The service condition during each of these operations is important in considering furnace refractory life.The improvements in operating practices and furnace 'construction which enabled the capacity of the furnaces to be increased are discussed. The life between major repairs to side walls has increased from 90 charges to300 charges.The scope for future improvement is considered and areas for development are suggested.

Jan 1, 1977

By Jeffrey D. Thatcher, Debra W. Struhsacker

With the burgeoning development of precious metals heap leach mining projects throughout the country regulatory agencies are beginning to take a closer look at the short-and long-term environmental consequences of heap leach mining. This increase in regulatory review is occurring on federal, state and local levels, and is affecting both large- and small-scale mining developments. Small-scale mining developments are receiving especially critical regulatory scrutiny because in the eyes of some regulatory agencies, small developers lack the credibility automatically accorded to major mining companies. This is due in part to a bad image of small miners based upon past environmental problems and permit violations caused by a few, small operators. The proponent of a small mining development thus faces special problems during the project permitting process, and must convince the regulatory authorities of his company's ability and commitment to plan, develop, and decommission a mining operation in compliance with environmental regulations. Not only must the small developer have a thorough understanding of the regulatory requirements affecting his project, he must also devote considerable effort to careful internal planning in order to produce a well organized approach to project permitting. The importance of proper planning cannot be overstated. Project planning is key to convincing the regulatory agencies that the small miner is capable of developing a viable project. More- over, the economics of a small mining project demand permit acquisition at modest cost and in a timely fashion. A well planned permitting effort will thus ensure that permits are received within budget and on schedule. This paper will review the federal, state, and local permitting requirements for heap leach projects, and the variability of these requirements from state to state. The environmental assessment process for projects developed on public lands, and the acquisition of zero- discharge water quality permits, air quality permits, and local special use permits as they apply to small mining developments will be discussed. The paper will conclude with a review of project decommissioning and cyanide neutralization requirements and their implications for small-scale heap leach projects.

Jan 1, 1987

By M. Nduna

Surface properties of metal sulphides have a great significance in various areas of engineering and science, such as acid mine drainage, contaminant sorption, and metal separation. In various attempts at producing metal sulphide particles from synthetic solutions, prodigious quantities of nuclei that grow only to colloidal dimensions have been frequently reported. This copious nucleation is promoted by the high levels of supersaturation that characterize most precipitation reactions. Colloidal particle formation in precipi¬tation-based separation processes results in sub-optimal solid-liquid separation, which is alleviated by the production of more highly crystalline particles or agglomerates. The current work approaches this challenge from an electrochemistry perspective, by measuring surface charge potential of precipitant particles during metal sulphide precipitation with respect to the concentration of metal sulphide lattice ions in solution. Electrophoresis was used to measure the metal sulphide particle zeta potential and the settling properties were obtained by performing settleability measurements using an Imhoff settling cone. A suspension of copper sulphide particles was precipitated from synthetic solutions of copper and sulphide ions at equimolar concentrations. Immediately after precipitation the copper sulphide particles had a zeta potential of -50 mV and a settleability of about 7 ml.l-1. With the addition of copper ions the settleability increased by a factor of nearly three times and the zeta potential also increased to a maximum of -40 mV. A decrease in zeta potential to a minimum of -60 mV was observed after the addition of sulphide ions and this was associated with a settleability of 0 ml.l-1.

Jan 1, 2013

In eastern China, most of the copper skarn deposits occur in folded troughs which are controlled by the EW-trending faulted fold systems (the Pal-Asian geotectonic domain), and the NNE-trending rift or fault zones (the Marginal-Pacific geotectonic domain), particularly the later. From the north to the south, there are four troughs hosting the main copper skarn deposits in eastern China: the Yanliao Trough, the Yangzi River Trough, The Qiantang-Yuanshui Trough and the Zichen Trough. There are more than 30 copper skarn deposits in eastern China, and ore reserves of each deposit are between 30 to 100 Mt with average grades over 1% Cu.    Most of the large copper skarn deposit-related intrusions are Mesozoic in age (170 to 100 Ma) and were emplaced during the Yanshanian Movement. Outwards from the intrusion bodies, both the skarn alteration and mineralisation show certain patterns of zonation. Mineral assemblages indicate a relatively high oxidisation state during metasomatic alteration and mineralisation. Sulphur isotopic work indicates that most d34S values of the sulphides are between ~4 to 3ë suggesting a common magmatic sulphur source. Fluid inclusion and oxygen isotopic studies suggest that early-stage fluid shows magma-related fluid characteristics although meteoric water was involved during late-stage alteration.

Jan 1, 1995

By S Jackson, I Arbuthnot

The use of High Rate Thickeners has gained wide acceptance in the mineral treatment industries. The design of these units is characterized by an efficient deaeration and flocculation chamber, and introduction of the flocculated feed solids into a preformed floc bed zone. By these means the settling process is accelerated and consequently High Rate Thickeners achieve a significantly higher throughput per unit area than conventional thickeners.   The object of a control system on a High Rate Thickener (HRT), as on a conventional thickener, is to obtain the required underflow density and overflow clarity at all feed conditions. The feed conditions which may vary include volumetric and mass feed rate, pulp density, particle size and particle type. A conventional thickener has a large volume and cross sectional area, and changes in performance occur slowly û the operator has time to observe and react to these changes to maintain control. On a HRT, there is a much reduced residence time and therefore control parameters need to be reset more frequently. Although manual control is possible, the use of automatic control systems is therefore desirable to avoid excessive operator attention, while optimizing control of density and clarity. Automatic control of a conventional thickener is usually achieved by an underflow density loop which regulates the rate of withdrawal of underflow. A turbidity meter is sometimes used to measure overflow clarity and regulate the addition of a coagulant or polymer flocculant. These measures are not adequate on a HRT, because they would not give optimum control and could lead to excessive flocculant use. To achieve optimum operation in a HRT, the floc bed level should be maintained above the feed inlet point in the thickener. This bed level has become the key variable around which most control systems have been designed. However, a number of problems have occurred which has resulted in poor control, or only partial control of thickener performance. We will describe some of these problems, and a solution which is simple and effective.

Jan 1, 1990

Escalating energy and electricity costs have become one of the largest drivers of expenditure in mining operations. Over the last eight years, energy costs have tripled when expressed as a percentage of total expenses in South African mines. In an effort to manage and reduce electricity costs, energy management strategies can be developed, inefficient operating units replaced, and the operation of energy-consuming components of ventilation systems optimized. Power consumption on mines is controlled mainly by three strategies, namely load clipping, by which energy use is reduced for certain parts of the day; load shifting, by which energy use is shifted to other parts of the day; and energy efficiency, by which energy use is reduced permanently. In this paper several projects that were implemented using the first two strategies of load clipping and load shifting are investigated. The actual and potential savings that can be achieved by implementing such energysaving interventions are presented. To reduce the operating costs of ventilating and cooling underground mines permanently, system optimization studies must be completed. Methods that can be used to reduce energy usage by optimizing cooling and ventilation systems are described, and network simulation models that accurately reflect the current and planned ventilation conditions are discussed. These models are then used to examine various options for improving the overall ventilation and cooling strategy. Different optimization scenarios can be simulated, and this assists the design engineer in obtaining the most energy-efficient system that will satisfy design workplace conditions. The final outcome is a reduction in operating costs, which can result in better operating margins and an extension of the life of mine.

Jan 1, 2014

This paper presents an analysis of the production data for the period 1861 - 1953 from hydrothermal gold-silver deposits of the Hauraki Goldfield. To directly compare the metal content of the deposits a figure of ounces of gold equivalents (oz gold equivalent) is calculated from the value of the gold-silver bullion produced from each deposit. Frequency distributions for ore tonnage and oz gold equiv. appear to be lognormal and show a high proportion of very small deposits, with 90 per cent less than 100 000 tonnes. The deposits when plotted in order of size fall roughly on a smooth curve which suggests that the size distribution is not random. A large proportion (68 per cent) of the total gold-silver extracted from the Hauraki district was contained in the largest deposit û Waihi. A technique used for predicting undiscovered mineral resources is ZipfÆs law, which relates the size of an item to its rank order. The figures for ounce gold equivalents from the major Hauraki deposits fit ZipfÆs law remarkably well. Taking Waihi at 6.8 million oz gold equivalent as the rank one deposit, Thames is number five and Karangahake number seven. A Zipf plot indicates that down to rank 100 (68 000 oz gold equivalent) only 28 per cent of the total gold-silver resource in the Hauraki Goldfield has been extracted. A further 72 per cent or 25.4 million oz gold equivalent, including the deposits of rank 2, 3, 4, 6, 8, 9 and 10, are undiscovered. However, since some deposits will be deeply buried under younger rocks and others will be under the sea only a proportion of the total resource will be discoverable.

Jan 1, 1981

By Birger Schmidt

INTRODUCTION Conceptual design of the first Exploratory Shaft (ES-I) for the Nuclear Waste Repository in Basalt (NWRB) began in July 1981; detailed design began in February 1982, and was largely completed by December (RKE/PB, 1983). The intent was to begin shaft construction by January 1983. The site had been prepared at that time, a construction manager selected and on board, the starter hole excavated and lined, and steel casings were under procurement. Government policy changed, however, and construction was halted before the drill rig started turning. Construction is now planned to begin in 1988. ES-I is a part of the site characterization program for the NWRB. The shaft will be used to develop production data and related information relative to drilling shafts at the site near Richland, WA, and to provide access to the repository horizon for site characterization and testing. The early program called for one shaft and some 330 m (1000 ft) of drifting. The program has since expanded to include a second shaft (ES-II) and more extensive drifting and testing. Currently, both shafts are planned to be 1.8 m (6 ft) in finished diameter, but studies are underway to determine if the second shaft should be larger. The drilling method was selected for shaft construction primarily because it offered a significantly shorter construction period than conventional shaft sinking using freezing and grouting. The finished drilled shaft will be lined with a continuous steel lining. Personnel are safer during construction with a drilled shaft than with a conventionally sunk shaft. The drilling method

Jan 1, 1987

By M. G. Senyur

This study aims at investigating the structural characteristics of backfilling material. In this regard, spatial arrangement of solid particles and associated voids in a unit mass of coal mine refuse as backfilling material were tested. The materials were produced from coal mine refuse of Zonguldak Colliery, Turkey. The experimental procedures were developed to determine their void ratio (or its equivalent porosity), bulk density and the shape properties of constituent particles. The orientation fabric and the co-ordination number were the other two fabric elements determined. The filling materials were sieved and their particle size distributions were found. The results obtained by experiments were related to the particle size distribution parameters, namely, the coefficient of uniformity and the effective size. It was concluded that mean value of void ratio is correlated with coefficient of uniformity. The standard deviation of porosity as an index of fabric heterogeneity is clearly correlated to effective size. By an original experiment, the frequency distribution of coordination number was observed as binomial in uniformly graded materials. Also, the co-ordination numbers of test mixtures were calculated by the Marsal method and results obtained showed a good correlation between the minimum particle size and number of contacts per unit area.

Jan 1, 1998

Bioleaching of Weathered Saprolite - Heavy Metal Adaptation Mechanisms of Aspergillus foetidus Nickel laterite ores remain important to the future supply of Ni and Co as they contain the bulk of known nickel and cobalt reserves (80 per cent and 90 - 95 per cent respectively). Current commercial extractions of Ni and Co from nickel laterite ores are energy intensive and operational costs are high. Microbial leaching of oxide ores has the potential to offer a much needed step-change in the technology for processing laterite ores. Biological leaching of low-grade nickel laterite is based on a non-traditional leaching of oxide minerals using heterotrophic micro-organisms. The organisms solubilise metals by excreting organic acids; these acids then form complexes with heavy metals. Optimisation of the process in in-situ application, however, has been hampered by the toxicity of the heavy metals that are being leached by the organisms. Our recent study has shown that organisms are able to develop tolerance towards heavy metals by adaptation. This study examined the extracellular metal detoxification mechanisms of A. foetidus in 0.2 per cent (wt/v) to 0.7 per cent (wt/v) of weathered saprolite ore. To support our analysis, FTIR, CHNS and microscopy were used to confirm the participation of specific functional groups in the extracellular detoxification process.

Sep 13, 2010

By Robert E. McIvor

"The Functional Performance Equation for ball milling circuits allows us to isolate the circuit classification system efficiency (CSE) from the mill’s grinding performance. The factors which affect circuit CSE are reviewed, with emphasis on water usage at the classifiers. It is shown that manipulation of such water usage can be carried out to improve plant grinding circuit efficiency, at times by more than 30 percent.THE FUNCTIONAL PERFORMANCE EQUATIONObservation of the feed and product size distributions going into and discharging from the mill in grinding circuits with low versus high circulating load ratios initially led to the definition of “circuit classification system efficiency” (or CSE, McIvor, 1988a), and ultimately the discovery of the Functional Performance Equation (McIvor, 1988b, and McIvor et al, 1992). The CSE is the percentage of “coarse” (typically with reference to the plus P80) size material occupying the mill (versus “fines” or product size material, finer than the circuit P80), and can be calculated by taking the average of the percentage of coarse material in the mill feed and mill discharge. As this also represents the percentage of the mill energy expended on targeted, coarse size material, it is directly proportional to overall grinding circuit efficiency and production rate. This is all clearly expressed in the Functional Performance Equation for ball milling circuits, which is derived as follows.We define “fines” as any product size material, and “coarse” as that targeted to be further ground, the two typically differentiated by the circuit target P80. For any grinding circuit, the production rate of new, product size material (fines) must equal the specific grinding rate of the coarse material (i.e. fine product generated per unit of energy applied to the coarse material) times the power applied to the coarse material."

Jan 1, 2009

Peculiarities of Quartz Distribution in Zinc Flotation Products and their Influence to Mineral Processing

Sep 13, 2010

In order to ensure safe mining and reduce surface damage in shallow multiple-seam mining, the failure characteristics of interburden strata with different coal pillar offset distances between pillars in the upper and lower seams, the distribution characteristics of stress concentration in coal pillars, and the development characteristics of stratum cracks and subsidence were physically investigated and also using UDEC2D software. Meanwhile, the effect of different coal pillar offset distances on the stress concentration of coal pillars and development of stratum cracks were studied. Based on those results, a formula for safe mining and reducing surface damage was established, which provided a theoretical basis for safe and environmentally friendly mining in shallow multi-seams. According to the results of the study, the optimal coal pillar offset distance (the side-to-side horizontal distance of the upper and lower coal pillars) between the upper and lower coal seams was developed to reduce the stress concentration of coal pillars and surface damage. The results of this study have been applied in Ningtiaota coal mine and have achieved good results in safe and environmentally friendly mining.

Jul 28, 2020

By Wolfgang G. Brunner

The closing of the gap in the European waterway- net is one of the big and challenging traffic projects following the German reunification. The water canals in the North German plain connect the Rhine river, the border between Germany and France, with the Oder, the German border river to Poland. As early as in the 30's of the 19th century the planning and construction of a ship- lift and a canal bridge started, in order to close this last big gap in the system between the Mittelland Canal and the Elbe- Havel Canal near Magdeburg. This main waterway connects the West of Germany, known for its coal mines and steel mills, with the capital Berlin, and from there it goes on into Poland. The building activities started in 1934 but came to a complete stop in 1942 because of the war. The communist government in East Germany was not interested in continuing this huge project, including the ship lock Rothensee, the canal bridge crossing the river Elbe, the former border river between West and East Germany, and the lock Hohenwarthe due to lack of political backing along with low construction capacity.

Jan 1, 2000

By Adnan A. Malik, Tadashi Maejima, Jiro Kuwano

"ABSTRACTTheoretical approach to estimate the ultimate pile capacity gives a rough idea at the initial stage of design that later on strengthen by the execution of static pile load test at site. The static pile load test is the only best option for the estimation of ultimate capacity of various types of piles. There are various methods based on strength, serviceability, net deflection for end bearing, shaft adhesion, graphical and extrapolation approaches for the interpretation of pile load test data to calculate the ultimate capacity. In this paper an attempt is made to evaluate the best-fit method for the estimation of ultimate capacity of single helix screw pile. The pile load tests on model scale were performed on screw piles of different helix diameter. The purpose of adopting model scale of testing was to achieve a state at which settlement increases without further increase in vertical load. The ground was compacted with dry sand at denser state. It was observed from the test results that extrapolation methods such as Chin- Kondner and Decourt predict the load settlement curve of screw piles very well, however ultimate pile capacity was on higher side which may not be suitable for the strength of helix plate. Decourt approach to plot the pile load data showed clear indication of the deformation of helix due to strong subsurface condition. A modified approach in Decourt method is proposed for estimating the ultimate capacity of screw pile having deformed helix whereas reduction factor is suggested for Chin-Kondner method for the estimation of ultimate capacity of intact screw pile.INTRODUCTIONDeep foundations are used to avoid the soft ground at shallow depth that is not suitable for carrying the structural load. Different types of piles have been used to transfer the load to deeper stratum. The screw pile is one of the new piling method and its use is considerably increasing. It consists of a cylindrical steel shaft with one or more helices at various length of the shaft. The diameter of helices (Dw) is usually 2 – 2.5 times the shaft diameter (Ds). The pile is installed to the required depth through torque and pressure. The advantage of screw pile over other piling system is its quick installation mechanism, high end-bearing and uplift resistance, noise reduction and minimum use of man power."

Jan 1, 2014

By Raja V. Ramani

The potential usefulnuss of reclaimed surface-mined land has received much attention in recent times. This attention is partially due to the establishment of federal environmental reclamation standards but concern for achieving better land uses has also been shown by interested members of the mining industry. In an effort to develop a procedure for evaluating postmining land use potentials, specific mines in various regions of the U. S. were studied to determine the extent of current mined-land planning and to discover characteristics that are regional in nature. As part of this investigation, a 430-acre surface mine in Clear-field County, Pennsylvania has been studied. Established site planning principles have been applied to the case study site including formation of a data base, development of alternate land use plans, and evaluation of the economic, environmental, and social impacts of the land use alternatives. Key factors affecting site realization have been identified along with positive suggestions for applying land use planning processes to mined-land planning.

Jan 1, 1983

By Arturo Ressi di Cervia

From the times when men in lacustrine environments drove wooden piles into the mud to elevate their dwellings, until the beginning of the twentieth century builders reacted to the conditions found in the location of their proposed structures by attempting to distribute their loads in ways that could be supported by the foundation's soils; or, if those were unsuitable, by moving the structure, whenever possible. While many major structures were built on stable ground (the pyramids were founded on rock), others were built on [ ]

Jan 1, 2000

Eco-Efficient Gravity Separation Solutions in India Sustainable development and social responsibility issues are a principal aspect of mineral processing operations around the world. With the need for more environmentally effective technologies, some gravity separation systems have provided eco-efficient mineral processing solutions in places where it is not otherwise viable because of lack of fresh water or for other environmental reasons. Advanced spiral separation technologies developed in Australia offer a cost effective and environmentally viable way to process minerals. In particular, we review recent case studies of spiral plants commissioned in India where environmentally sustainable solutions to design problems included the use of spirals operated with sea water and the use of high capacity (HC) spirals to provide low consumption of energy and materials and a reduced plant footprint. This paper evaluates the performance of various spiral plants in India and how critical environmental issues which affect the overall viability of wet concentrating processes where resolved.

Sep 13, 2010

By Kenneth H. Johnston

This publication describes a thermal-recovery project and two waterflood projects in Carter, Garvin, and Stephens Counties, Okla., that will be visited during the 1966 annual tour by the Bureau of Mines in cooperation with the Kansas-Oklahoma Waterflood Association. Among the unique features of the projects arc (1) the movement of heavy (15° to 28° API gravity) crude oil through the reservoir and into the well bore with energy furnished by burning a portion of the crude oil therein; (2) the use of an inverted nine-spot pattern with dually completed injection wells, to produce oil from deep (8,200 to 10,200 feet) reservoirs; and (3) the flooding of five sand lenses separately by using controlled water injections through multizone completed injection wells. Discussion of the individual projects includes information on their early history, method of completing and operating wells, source and treatment of injection fluids, oil production decline curves, and the results obtained from the development.

Jan 1, 1966

By S. C. Tennant, G. M. Steed

Paper presented at Mineralisation in the Caledonides, the Mike Gallagher memorial meeting held in Edinburgh, 27-28 June 1996. Immobile-element lithogeochemistry is providing a detailed chemostratigraphy of the submarine Ordo-Silurian volcano-sedimentary sequence. Primary lithologies and magmatic affinities of the sericitised and silicified volcanics are determined from binary plots of Nb, Zr, Y, TiO2 and Al2O3, while mass-change calculations using immobile-element anchors can identify and quantify zones of significant hydrothermal alteration. Stratiform polymetallic mineralisation at the western margin of Parys Mountain, around the Penymynydd fault zone, has been shown to have a distinct hanging-wall and footwall stratigraphy. These ore zones are probably part of a homoclinal, north-younging volcano-sedimentary sequence. The apparent stratigraphic complexity results from primary lithofacies variations and pervasive alteration, with the modifying role of the Caledonian orogeny much less than previously suggested

Jun 19, 1905