Search Documents

By D. E. Pollock, J. A. Organiscak

Water sprays and water powered scrubbers have both been utilized in the mining and milling industry to suppress airborne dust. Unconfined water sprays operated at lower water pressures of ?689 kPa (?100 psig) can be very effective at wetting the mine product at the dust source and significantly reducing the amount of respirable dust that becomes airborne. However, unconfined waters sprays can be somewhat ineffective in actually removing airborne dust from the air. On the other hand, water powered scrubbers operating at higher water pressures of ?1,724 kPa (?250 psig) in physical enclosures or ducts have previously been demonstrated to be very effective in removing airborne dust from the air. These higher operating water pressures are uncommon in many mines and mills, so their use is limited. The National Institute for Occupational Safety and Health (NIOSH) recently investigated the performance of a lower-pressure, water powered inline series spray scrubber for removing localized airborne dust emitted at the source. Results showed noticeable improvements in airborne dust capture efficiency through the operation o f multiple inline series hollow cone spray nozzles within a round duct or pipe at the same water pressure as a single spray. Operating hollow cone spray(s) at higher water pressures noticeably improved airflow through the scrubber and yielded some additional scrubber efficiency improvements. Thus, in-line spray scrubber efficiency trade-offs were observed to be made by altering spray power components of water pressure and/or quantity (number of sprays). Results show that, on average, up to 0.23 and 0.32 m3/s (484 and 679 cu ft per min) of airflow at 0.81 and 0.69 dust capture efficiencies can be achieved with three 81° and 33°hollow cone inline series sprays, respectively, operating at 1,655 kPa (240 psig).

By John B. Sabey, Vernon R. Degner

The industrial coal processing trend toward greater fines production, due to mining techniques and customer requirements for reduced ash and sulphur content in the fine coal product, is the basis for ongoing efforts to improve the performance of the flotation machine. WCO has successfully adapted the principles of the beds Column to a full size machine prototype. Recent plant evaluation tests confirmed the initial promise of this concept by achieving a considerably lower ash product while maintaining the combustible recovery level of conventional flotation machinery. The paper will include a review of the fundamental principles of the beds Column concept, together with a summary of the WEMCO R&D Program from concept evaluation and laboratory testing, through pilot, to full size machine tests. The performance of the WEMCO/Leeds flotation column will be compared to conventional flotation concepts using a flotation "kinetics" approach, which quantifies the floatable and non-floatable specie recovery performance using the Klimpel model as the basis for analysis. The variety of distinct features unique to this concept include a series of barrier rods which are used to advantage, often together with countercurrent reflux water flow, to achieve a significant improvement in product grade. The hydrodynamics associated with the mechanics of "gangue stripping" from the rising "air bubble-floatable specie" matrix will be briefly reviewed.

Jan 1, 1988

By Glen Church, Don W. Deere, Christoph M. Goss

The Standley Lake Dam Rehabilitation Project in Colorado included the complete replacement of the outlet works. This required two 1.8m (6 ft) diameter microtunneled wet lake taps, 380m and 186m (1246 ft and 636 ft) long, a permanent valve shaft 12.2m(40 ft) wide and 32m (105 ft) deep, and a 3.5m (11.5 ft) diameter (962 foot long) outlet tunnel driven with a roadheader. The tunnels were driven in low-strength, expansive, and slickensided claystone. The paper addresses the site investigation, shaft construction, roadheader performance, shotcrete placement, tunnel convergence, long distance microtunneling, and wet lake taps.

Jan 1, 2005

By Steve Massman, Edward Wipf, Gary Beerkircher

"As mine size and tonnage continues to increase, material handling/processing equipment has also increased in size with 400 MT haul trucks, 2000 KW crushers, 12 M SAG/AG mills, 8.5 M ball mills, 3000 M3 flotation cells and 12.5 MW HPGR’s all with planned designs to increase in size further. Related equipment including vibrating screens have also increased in size with screens seeing feed rates of 3000 MTPH. Open circuit SAG Pre-Crush and closed circuit HPGR flowsheets are becoming more common with large screening requirements. Large multi-slope (banana) or horizontal screens are commonly used for these applications, however as the size of these screens has increased, the number and size of the brute force/overhead exciters has increased but with limitations. An example is a SAG discharge screen that will see surges of material from the SAG mill which overload the screen, reducing the screen stroke or throw causing a large reduction in screen efficiency with excessive fines & moisture in the screen oversize feed to the pebble crushing circuit. This paper will present some actual examples of the use of Two-Mass screens as a solution to these overloading problems and the advantages of Two-Mass screens in other high tonnage applications.Brute Force Drive Compared to Two Mass Drive Vibrating ScreensThe standard single mass screen as depicted by figure 1 is generally recognized in the mining industry. It is characterized by the screen body – labeled as the single mass (Mt) that is supported by isolation springs (Kiso). The stroke needed to process material is obtained by incorporating large eccentric wheels and/or drive boxes (Fb) directly mounted to the screen body via a drive tube."

Jan 1, 2017

By Hargraves A. J

The paper outlines events at the Collinsville State Coal Mine, Queensland, leading to the practice of full face multiple shotfiring in bord and pillar development places. The 1954 disaster is referred to, and factors involved in simultaneous shotfiring in coal are discussed. Promising preliminary multiple shotfiring tests at the Colliery are described, as well as the resulting routine measures adopted, and the changes involved. The subsequent inducing of two outbursts under safe conditions by remote multiple shotfiring is given as justification for the changes made.INTRODUCTIONFollowing a disastrous instantaneous outburst (1.0.) of coal and gas at the Collinsville State Coal Mine in 1954, the necessity for inducer shotfiring for the control of possible further outbursts was established. However this mine, immediately classified as gassy after the 1954 outburst, is subject to the general restrictions pertaining to gassy mines which at present preclude the use of inducer shotfiring due particularly to the non-existence of a permitted exploder for more than six shots, and further, because permitted multipleexploders are not designed for remote firing through long lengths of cable. This situation was met by arresting or reducing progress in the production places, thereby reducing the danger of outbursts while means were being considered to achieve overall maximum safety.In August 1957 two full faces were successfully blasted in experimental simultaneous rounds. In June 1958 four full faces were blasted, and in October 1958 full face grunching without prior cutting, Le. inducer shotfiring, was introduced in No. 1 Tunnel as a production feature. In March 1960 it...

Jan 1, 1960

By Robert Stefanko

With passage of the Clean Streams Act of the Commonwealth of Pennsylvania and its impact on the coal industry, considerable research has been conducted to explore various approaches to the problem, including deep-well disposal. Available drillhole data from gas and oil wells were used to develop cross -sectional maps for various portions of the state and potential disposal zones were evaluated. Bethlehem Mines Corp., faced with a severe water problem at its Marianna operation in Washington County, cooperated with the Dept. of Mining at The Pennsylvania State University in establishing a 1500-ft well into the Salt Sands for the purpose of determining the feasibility of mine water disposal. The thickness, porosity, and permeability of the formation at the well site proved to be below what had been anticipated from drillhole data. Further, subsequent hydraulic fracturing did not improve the flow characteristics of the well; pumping pressures remained in the range of 1800-2000 psig for disposing of water at the rate of 150 gpm. The legal problems of disposal at the site were very formidable. When the Salt Sands proved to be less than satisfactory, permission could not be obtained to dispose in other promising formations. The paper details many of the problems associated with the experimental well and makes an assessment of the potential for deep-well disposal of mine water. The concept of disposing of liquid industrial wastes by deep-well injection is not a new one. Brines associated with crude oil long have been disposed of in this manner, with the additional benefit of aiding secondary oil recovery. More recently, with the expansion of nuclear energy, the lethal, highly radioactive wastes which are by-products of the fission process have created severe disposal problems. During the past ten years, a variety of industries have resorted to subsurface disposal, some of the details of which are given e1sewhere.l,2 The list reveals wide variations in injection rate, pumping pressure, cost, and waste disposition. Included are successful installations in Western Pennsylvania. Enactment of more restrictive clean-water legislation in Pennsylvania recently had a great impact on the coal industry. Among its provisions was the reclassifica-tion of most mine water as industrial waste whose dis-posal is prohibited in any stream of the Commonwealth. This had the effect of accelerating research in a variety of areas, although treatment methods still retained primary interest. When a feasibility study of deep-well disposal was proposed to the Pennsylvania Dept. of Mines and Mineral Industries, the Coal Research Board (CRB) approved it. This paper summarizes the efforts on this project. Acid mine water is a chemically complex liquid. having no definite quantitative relationship among its constituents. However, it is the iron disulfide (FeS2) associated with practically all coal seams that produces the objectionable products present in acid mine water when combined with air and water. The principal contaminants are sulfuric acid (H2SO,) and ferric hydroxide (Fe(OH)2. Ferric hydroxide is a rust-colored gelatinous precipitate that coats stream bottoms and destroys aquatic life. However, other ions and bacteria are present in acid mine water in varying amounts.

Jan 1, 1971

IN this paper an attempt is made to describe the sluicing operations on the tin fields of north-eastern Tasmania. No claim is made to completeness, for much of the ground has already been covered, and nothing is to be gained by needless repetition. On this account some portions of the subject have obviously received but attention in order that others may be rather more fully dealt with; for instance, referring to the accuracy of various methods of valuing alluvial deposits, particulars of efficiencies, and water duties on both overburden and drift; also, the system of recording water distribution, &c. The plans of the tin-streaming shed, sluice and feed race, and overburden tail-race represent types of the most modern design.GEOLOGY. The principal alluvial dcposits being worked at the present time are situated either in the ancient or modern bed of the Ringarooma River or its tributaries. This river flowed in a north-easterly direction, receiving numerous tributaries on either bank...

Jan 1, 1910

By Tim Hurley

On Friday, May 27, 1983 at about 6 p.m., an avalanche occurred at the Revenue-Virginius Mine. Six mine personnel and two contract diamond drillers were trapped when the avalanche covered and blocked the portal, the only access into the mine. The San Juan Mountain Range in southwestern Colorado is an old volcanic caldera. It has dikes and other intrusions, many of which are mineralized with sulfide ores rich in silver, gold, lead, zinc and copper. Several peaks rise above 4,260 m (14,000 ft) and the district has been the location of avalanches dating back to prehistoric times. This is evidenced by the numerous snow-slide chutes that are infamous enough to be named on topographic maps.

Jan 1, 2006

By S Piercey, M Doublier, B Eglington, D L. Huston, S Pehrsson

"An EXTENDED ABSTRACT is available for download. A full-length paper was not prepared for this presentation. The distribution of volcanic-hosted massive sulfide deposits through time is episodic, involving relatively short time intervals of apparent high productivity and long intervals of low productivity. This distribution is principally related to the geodynamic evolution of the Earth. The vast majority of these deposits is associated with the assembly of supercontinents and form along convergent margins, generally in back-arc basins or rifted arcs. This contrasts with the distribution of black smoker deposits, which presently form along both convergent margins, particularly in the western Pacific, and divergent margins at mid-ocean ridges. However, the latter environment is rarely preserved deep into the geological past.There also appear to be systematic patterns in a number of other features of volcanic-hosted massive deposits through time. Deposits hosted by mafic-dominated successions are dominant in Archean to Proterozoic rocks, whereas deposits hosted by felsic-dominated successions are most common in Phanerozoic rocks. Geochemical characteristics of felsic rocks within the host successions and ore lead and sulfur isotope data of the ores have also changed with time. This suggests changes in the process of subduction and/or changes in the characteristics of the over-riding plate with time, consistent with isotopic and geologic evidence for greater reworking of pre-existing crust during the Phanerozoic.Other secular changes that are reflected in characteristics of volcanic-hosted massive sulfide deposits include the redox state and salinity of coeval oceans. As an example, both the abundance of sulfate minerals and sulfur isotope patterns reflect the development of periods of anoxic conditions over time, with major intervals of anoxia reflected by a virtual lack or low abundance of sulfate minerals in volcanic-hosted massive sulfide deposits in the Mesoarchean to the Palaeoproterozoic, and shorter intervals since.CITATION:Huston, D L, Eglington, B, Pehrsson, S, Piercey, S and Doublier, M, 2015. Secular variations in the abundance and characteristics of volcanic-hosted massive sulfide deposits – implications for evolution of convergent tectonics and ocean geochemistry , in Proceedings PACRIM 2015 Congress, pp 475–480 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Mar 18, 2015

By Garnsey R. G T, Wenk G. J, Toop A, Sowerby B. D

A bulk mineral analyser (BMA) suitable for the determination of Cu or Ni in bulk ore samples has been developed at the Lucas Heights Research Laboratories. This analyser, which uses the nuclear resonance scattering technique, is highly specific to the wanted element. The technique has previously been extensively field tested for copper at Mount Isa, Queensland.The present paper discusses the field trial in 1982 of a commercial prototype BMA for nickel. The trial was undertaken at the lateritic nickel mine at Greenvale, Queensland. The BMA and its shielding, together with a laboratory spectrum analyser, were sited in the sample shed adjacent to the workings. Two hundred and thirty-eight ore samples taken directly from the mine blastholes were assayed by the BMA. The average mass of sample was 12 kg, metal contents varied from 0.2 to 3.5 wt/per cent Ni and 4 to 43 wt/per cent Fe and free moisture varied from 11 to 55 wt/per cent. A measurement took 10 min to complete, although this time could have been reduced at the higher nickel grades. The r.m.s. deviation between BMA and chemical assays was 0.09 wt/per cent nickel. Iron and bulk density were also determined by the BMA, r.m.s. deviations being 1.7 wt/per cent and 0.03 g/cmJ respectively. Similar results could be expected from a BMA in routine industrial use at other nickel mines.

Jan 1, 1983

By Joel Nonnweiler, Rafael Castro, Ross Webb

The three thousand foot long 66-inch diameter Folsom East Interceptor Section2B was completed accident free, on time and under budget with no measurable surface settlement. The tunnel passed through nested cobbles, highly abrasive sands and gravels, and abandoned mine workings with less than five-feet of cover at times. Preventing settlement was critical since the tunnel passed under a heavily traveled state highway. A pilot project to test microtunneling and pipejacking methods in the same ground conditions abandoned both drives before completing the planned drive lengths. This paper discusses performance of the conventional tunneling method selected to excavate the ground and the effectiveness of the ground modification techniques employed.

Jan 1, 2001

By J. Wagner, P. Eger, G. Melchert

In 1991, LTV Steel Mining Company decided to close an open pit taconite mine in northeastern Minnesota, using a passive treatment approach consisting of limiting infiltration into the stockpiles and wetland treatment to remove metals. Over 50 million metric tons of sulfide-containing waste had been stockpiled adjacent to the mine during its 30 years of operation. Drainage from the stockpiles contained elevated levels of copper, nickel, cobalt and zinc. Nickel is the major trace metal in the drainages, and prior to closure annual median concentrations ranged from 1.5-50 mg/L. Copper, cobalt and zinc are also present but are generally less than 5% of the nickel values. Median pH ranges from 5.0 to 7.5, but most of the stockpile drainages have pH greater than 6.5. Based on the chemical composition of each stockpile, a cover material was selected. The higher the potential a stockpile had to produce acid drainage, the lower the permeability of the capping material required. Covers ranged from overburden soil removed at the mine to a flexible plastic liner. Predictions of the reduction in infiltration ranged from 40% for the native soil to over 90% for the plastic liner. Five constructed wetlands have been installed since 1992, and have removed 60-90% of the nickel in the drainages. Total capital costs for all the infiltration reduction and wetlands exceeded $6.5 million, but maintenance costs are less than 1% of those for an active treatment plant. Since mine drainage problems can continue for over a hundred years, the lower annual operating costs should pay for the construction of the wetland treatment systems within seven years.

Jan 1, 1999

By Robert Keyes, Charle Knowles, Glenn Kendall, Gary Fletcher

"The metal mining industry in Canada has been dramatically affected by the changes that have occurred in the world mineral market place. World economic restructuring in the post ""oil shock"" period of the mid-1970s, greatly increased competition from suppliers in the developing countries, and commodity price and currency pressures have all combined to severely test Canadian competitiveness. In the new mining world, the rate of growth of demand for metals has declined due to product downsizing, materials substitution, and a relatively slower growth of over-all world economic activity.The interplay of market and political factors is complex. Canadian metal mining companies must compete in world markets against low-cost producers in developing nations whose priorities often appear to be centred on maximizing foreign exchange earnings to foster development goals and debt repayment. Many of these countries have high levels of government intervention in their mining industries. The result is a greatly in-creased number of suppliers all vying for a share of a world demand growing at a relatively slower rate than in the past. To be able to compete under these circumstances, Canadian companies have had to undertake 'survival mode' measures and look to new ways of doing things. In order to identify the effects that the recent market and economic trends have had on the Canadian metal mining industry, a study was undertaken by Canada Employment and Immigration to assess these changes and their implications for the metal mining workforce.The Canadian Occupational Projection System (COPS)—Sector Study Group with the cooperation of the Mining Association of Canada, undertook a human resource survey to gather current employment and occupation information. This formed an important part of the Canadian Occupational Projection System Metal Mining Sector Study. This article addresses the with survey results, a C.E.I.C. worker mobility study, and trends and issues that are changing the mix of jobs and the way they are being done.Figure 1 shows metal mining employment for the period from 1974 to 1984. It provides a clear picture of the employment swings that the industry has experienced especially during the recession period of 1981 to 1983. From 1981 to 1983, employment dropped by 14 000, from 68 000 to 54 764, and then dropped to its lowest point in 1984 of 52 783. We feel that employment in the medium term will be flat with growth in gold mines being largely offset by continued workforce rationalizing in other sectors.Perhaps the key point is that equivalent levels of output have been achieved in the recent period (1981-1984) with a workforce that is 25% smaller than it was in 1974. This also raises the questions which the COPS/MAC survey and COPS mobility study sought to clarify, namely, what jobs have been cut and where have these people gone? Equally important are the questions of occupational skill level changes, and what types of jobs are declining and which ones are becoming increasingly important, as economic and technological changes have altered the mining work place."

Jan 1, 1987

By Oscar Concha

El presente texto describe la exploración, geología, controles estructurales, mineralización y los tipos de alteración hidrotermal del yacimiento minero Cuajone, situado al sur de la Cordillera Occidental de los Andes y en el flanco Andino de Moquegua. En 1937, se inicia su exploración a través de una campaña exploratorla de la empresa Cerro de Pasco, donde se determina la zona como un proyecto potencial de cobre porfirítico de baja ley. Posteriormente en 1942, se inicia la primera campaña de perforación diamantina exploratoria y en 1969, se inicia la etapa de construcción y desbroce de material para preparar la mina. De otro lado, se ha desarrollado un modelo de la evolución del yacimiento desde las rocas preminerales del Grupo Toquepala, de las cuales la andesita basáltica fue una gran receptora de la mineralización de cobre originada por la intrusión de un primer pulso de latita porfirítica.

Apr 26, 1999

By K. Leutwyler, H. L. Bigelow

Jan 1, 1966

By Denis Labrie

Le minage en profondeur sous contrainte modérée à élevée présente de nombreux défis aux opérateurs et aux ingénieurs de mine notamment au niveau du contrôle de terrain et de l?environnement minier souterrain, pour assurer la sécurité des travailleurs sous terre et la continuité du cycle d?opération. Des conditions de contrainte élevée signifient une pression accrue au front de taille et sur les structures minières tels les piliers de mine et les fins de zone, un risque de rupture violente ou de coup de toit plus élevé, des zones de rupture plus grandes au pourtour des excavations, des charges accrues sur le support de terrain, etc. Le présent article fournit un aperçu du travail fait à l?intérieur du Programme de Contrôle de terrain de CANMET au cours des sept (7) dernières années, entre 1995 et 2001, pour comprendre et suivre l?évolution des niveaux de contrainte à l?intérieur des structures minières. Les propriétés déterminées en laboratoire sur des échantillons rocheux et les prévisions effectuées au moment de la conception sont comparées avec les observations effectuées en chantier à la paroi des excavations et à l?intérieur de la masse rocheuse. La plupart des cas discutés ici montrent une corrélation satisfaisante entre les observations effectuées en chantier d?une part, et les résultats d?essai obtenus en laboratoire et les calculs réalisés lors de la conception d?autre part. Ces observations peuvent donc être considérées comme des moyens relativement sûrs pour vérifier et suivre l?évolution des niveaux de contrainte présents à l?intérieur des structures minières.

May 1, 2002

By H. Kazemi, M. S. Seth

The effects of anisotropy and stratification on flow behavior and production performance of oil and gas wells have been studied by numerous authors.1-3 Lefkovits et al.l studied the performance of totally penetrated, stratified bounded reservoirs with no crossflow. Others have studied a similar problem, but with crossflow; Russell and Prats2 have summarized the findings of these papers. Muskat3 studied the steady-state behavior of liquid flow for a partially penetrating well in an anisotropic system and concluded that the productivity weakly depended on the directional permeability ratios (kz/kr>0.1). Nisle4 used the classical method of point source solution to the diffusivity equation to study the effect of partial penetration on pressure buildup of oil wells in an isotropic system. He found that the theoretical pressure buildup curves consisted of two straight lines, the one at early buildup times having a slope proportional to the flow capacity of the open interval (l-d)k, and the other having a slope proportional to the flow capacity of the entire formation hk,. Later Brons and Marting5 supplemented the findings of Nisle and concluded that partial penetration gave rise to a pseudo damage, which reflected itself as a skin factor in pressure buildup calculations. Using the pseudo skin, they calculated the impairment of productivity of the production wells, which agreed well with the results of Muskat.6 Pizzi et al.,? using an electrical analog of a stratified system, concluded that a high pseudo damage resulted if the reservoir was partially penetrated. Harriss studied the optimum spacing and arrangement of perforations in cased holes. Hantush9 derived an expression for pressure distribution in an unbounded reservoir with restricted flow entry. Seth10 extended Hantush's work to a bounded reservoir. Odehl1 has studied a similar problem for steady-state conditions. The purpose of this work was to investigate: (1) the combined effects of anisotropy, stratification with crossflow, and restricted flow entry on pressure transient analysis of flow and buildup tests, (2) the feasibility of calculating the horizontal permeabilities of intercommunicating stratified systems, and (3) the pressure interference tests in such systems. Theory The partial differential equation governing the isothermal flow of homogeneous fluids of constant compressibility is given by Eq. 1: The initial and the boundary conditions are: 1. The reservoir potential is initially constant, say 4v

Jan 1, 1970

By B. P. Nutter, M. Lebourg, J. A. McAlister

The Multi-Flow Evaluator (MFE) is a new system of tools providing an original approach in drill-stem testing. It improves control during the testing operation and gives a more accurate evaluation of the fluid recovered while providing additional pressure information for reservoir analysis. The tools are operated entirely by up and down motion of the drill stem. This up and down operation provides a positive means of control and offers easily observed surface indications of tool operating position. An unlimited number of shut-in and flow periods may be taken with this tool while in the hole. The key to the success of the MFE system of tools is the safety seal packer. Until this development, operation of the tools by up and down motion only had proven unreliable. The success ratio of the MFE now exceeds the ratio achieved by conventional tools. The equipment includes a 2,750-cc chamber in which a representative sample of the flowing formation fluid is trapped at the end of the last flow period and brought to the surface under pressure. The sample can be evaluated at the wellsite or transferred under pressure for laboratory analysis. The sampling feature of the tool allows a sample to be obtained from a reservoir which has suffered minimum influence from production. A representative sample can be obtained for laboratory or empirical analysis by employing a testing technique to minimize drawdown during flow periods. Interpretation methods to take advantage of this additional information are presented and supported by actual field examples. INTRODUCTlON The Multi-Flow Evaluator (MFE) represents the most recent technical advance in formation testing. Drill-stem testing techniques prior to the MFE have been limited in three areas—(1) operaiion, (2) recovery analysis, and (3) reservoir analysis. The tools in the MFE system allow maximum control during testing and provide test information superior to that obtainable with conventional tools. The system of tools and the operation procedures are described to illustrate the mechanical advantages over present tools. Methods of pressure build-up and fluid

Jan 1, 1966

By F. A. Forward, A. H. Ross, J. Halpern

Application of the carbonate leaching process to carno-tite ores has often been limited by the difficulty of obtaining simultaneous high recoveries of uranium and vanadium. The chemical aspects of this problem are discussed and the effect of prior roasting procedures on this discovery is described. IN treating carnotite ores by carbonate leaching it is often necessary to subject the ore to a prior roast. Among the advantages that may result from roasting are: 1) improvement in settling and filtering characteristics of the ore; 2) destruction of carbonaceous impurities that would otherwise contaminate the leach solution and consume carbonate reagent; and 3) substantial increase in extraction of vanadium, which is usually low when the un-roasted ore is leached. Recovery of vanadium may be an important factor in processing carnotite ores, and the fact that vanadium is usually recovered in good yield by acid leaching has often been an economic advantage over results obtained with carbonate leaching. It has been found that response of an ore to carbonate leaching, following roasting, depends primarily on its composition and on the conditions of the prior roast treatment, particularly with regard to the roasting temperature, the atmosphere maintained above the charge during roasting and cooling, and the presence of certain reagents. These factors, especially the last, virtually determine the extractions of uranium and vanadium attainable by carbonate leaching, as well as the reagent consumption on leaching, whereas adjustment of the leaching conditions has only a limited influence. These variables were examined systematically to elucidate roasting and carbonate leaching of carnotite ores and to establish a treatment yielding high recoveries of both uranium and vanadium. Tests were conducted on samples of four different Colorado Plateau ores, described in Table I. Roasting Procedure: The roasting tests were conducted in an electrically heated furnace in which the temperature was controlled to ±15°C. The ore (usually a 500-g charge) was ground to —100 mesh, mixed with the desired reagent, and spread in a silica tray to a bed depth of about 1/2 in. During the roast the charge was rabbled at intervals of 15 min. To provide free access of air the furnace was usually ventilated; however, in a few experiments a controlled atmosphere such as carbon dioxide or hydrogen was maintained above the charge. Leaching Procedure: The pulp, generally comprising 500 g of ore and a 2000-cc solution containing 80 g per liter of Na2CO8 and 20 g per liter of NaHCO3, was agitated in an autoclave at 120°C, under 30 psi 02. Samples were withdrawn periodically, and the solution and ore residue were analyzed. Under the conditions employed, maximum attainable extractions were generally achieved in 4

Jan 1, 1959