Search Documents

By Richard C. Rice

Laboratory and field data for wire ropes typical of constructions used in underground mine hoisting were obtained, screened, encoded and analyzed statistically. The statistical analysis of data for hoist ropes retired from service showed that rope remaining strength (or, conversely, strength loss) can be predicted with good accuracy if several nondestructive measures of rope damage are assessed. Found to be most important was the outer-wire corrosion rating, the electromagnetic (EM) nondestructive-inspection technique used for predicting strength loss, and the rope diameter reduction. Signs of rope deterioration such as broken wires or damage were also important indicators of strength loss. Based on the results of this investigation, a number of recommendations are presented that promise to yield better rope inspection and retirement criteria which will in turn lead to improved safety and efficiency in underground mine-hoist systems.

Jan 1, 1983

By J. C. Gerdeen

This project was a supporting effort with research contract H0230016 at White Pine Copper Company. Creep properties of White Pine rock were determined. These and properties for bolted joints were used in finite element analyses of sections of the White Pine Mine which included analysis of bed separations in the roof and sloping faults. In-situ experimental measurements were made of tension, compression, and bending of resin bolts by use of strain-gaged bolts. Evaluations of bolting effectiveness and comparisons of predicted and measured roof behavior are given.

Jan 1, 1976

By Mick Fritz, Tom Treleaven

The success of any blast is dependent on the accuracy of the blast design and field controls placed at the shot location. The procedure by which the data is collected and analyzed is paramount to accomplishing the anticipated blast results. lf the geometry of the blast is not measured correctly, then the results will not meet expectations. Measuring the geometry and compensating for bole hole deviations is crucial not only to the lnitlal blast but also for any consecutive blasts. Excessive bore hole deviation can cancel any new technology in use. However the instruments and skills required solving this Issue are readily available.

Jan 1, 1998

By Akul Joshi, Ming C. Leu, Robert Guttenberg, Susan L. Murray

The aerospace and automotive industries are facing a significant risk for cumulative trauma disorders from high-repetition, long-duration tasks. Additional risk factors such as shocks, vibrations and sustained uncomfortable postures oftentimes contribute to musculoskeletal, neurological injuries associated with the hand-arm system. The power tools used for the operation reduce the comfort and working efficiency of the operators, thus lowering their health and safety and the quality of operation. This paper investigates the fastening operation on the assembly line of a major aerospace company for quantifying hand-arm vibrations with the objective of developing a dynamic model of the hand-arm system. The model will be used to ascertain the effect of the various risk factors on the quality of the operation. Experiment Setup A system of three tri-axial accelerometers is used to collect vibrations entering the hand-arm system and their positioning follows the ISO-5349 standard. Reaction force during the operation is measured using a force sensor. The posture of the hand-arm system is measured using two goniometers and one torsiometer. The pilot study conducted has two subjects and one pistol-grip power tool. The experiment setup and positions of various sensors is depicted in Figure 1. [ ] Analysis Method The analysis consists of transmissibility of vibrations and frequency weighted acceleration based on the recommendations of the ISO-5349 standard [1,2]. The transmissibility [3] was deduced in frequency domain after measuring data in time domain from the

Jan 6, 2006

By H. S. Martin

The Phosphate Recovery Corporation operates three flotation plants, Nos. 1 and 2 concentrators about three miles northeast of Mulberry, Florida, and No. 3 plant at Wales, Tennessee. These plants represent the first commercial phosphate flotation operation and are also believed to be the largest nonmetallic flotation operation in the world at the present time. The details of this paper will be confined to plant No. 2, this being the newest and largest concentrator in Florida, and the flow sheet being practically the same as at plant No. 1. The No. 3 plant has been operated but a short time and has been shut down since December, 1932, on account of the decrease in phosphate rock production. The phosphate washers usually are located centrally on a known deposit so that about two hundred acres of ground can be mined economically to each washer location. The washers are moved to new areas when the distance becomes too great for economical pumping. The flotation plants are built either adjacent to a washer, so that current debris may be utilized, or on the site of a former washer where there is sufficient accumulated debris available for mining, and the flotation plants must also be moved from time to time. Most of the water used in the Florida flotation plants is recovered after passing through a circulating system where most of the fine suspended matter is settled out, but some make-up water is obtained from deep wells near the plant. Power is obtained from the Tampa Electric Co. through the distribution facilities of the International Agricultural Corporation. Flotation concentrate is hauled from the plant by trolley over the International Agricultural Corporation's trolley system, to the drying plant at Prairie, one mile northwest of Mulberry. Ore Treated In the pebble phosphate district of Florida, the phosphate mineral, or collophane, is usually found in horizontal beds of varying thickness

Jan 1, 1935

By A R. Bye

Energy comes at great cost to our world and societies and therefore we should use it wisely and optimally. Societal pressure is enforcing this and the industry must respond by being proactive.The mine-to-mill approach to integrated mine and semi-autogenous grinding (SAG) mill optimisation demonstrated that throughput gains of up to 20 per cent could be obtained through a closer match of blasted run-of-mine ore to the feed best treated by a SAG mill. Since that approach was developed, new drivers have risen to prominence including environmental costs and impact of energy, water, waste. This is set against a backdrop of reducing ore grade and increasing demand that is pushing up our impact on the environment. The new challenges demand new approaches.This paper explores the opportunities in taking traditional approaches to optimisation to new levels of two-way integration and incorporating potentials for ore upgrade into circuit design. The new mantra may be æflexible circuitsÆ û designing and building for the present and the future by allowing for the uptake of new and future technology.

Jan 1, 2009

By Lytman Jordán

En la actualidad, el proceso de Ore Control de Tintaya se convierte en un reto porque la naturaleza del yacimiento Metasomático de Contacto Tipo Skarn presenta una mineralización compleja a manera de pasas en una torta. En ese sentido, la cultura Sigma -que presenta poderosas herramientas estadísticas y de gestión de procesos-, logró conceptualizar el proceso de ore control e identificar y optimizar tres sub-procesos críticos: el muestreo de Blasthole, preparación y análisis de Muestras de Blasthole y el Ore Control Operativo. Por ello, el presente texto señala la optimización del oro control de Tintaya a través de la metodología Six Sigma, donde se logra mejorar el proceso desde el muestreo de blasthole hasta el envío de mineral a las plantas, se minimiza los eventos de fuga de mineral a los botaderos y con la data confiable de los blasthole, se elaboran modelos de corto plazo que permiten generar planes predecibles de minado.

Sep 9, 2007

By T. Soejima

In recent years, there has been a tendency in the field of foundation piling works to utilize piles of greater bearing capacity in order to meet increasing height and weight of modern building as a means of saving of piling cost. To satisfy these requirement, a new technique for large diameter bell bottom cast-in-place piling has been developed utilizing multi-head reverse circulation drilling system.

Jan 1, 2010

By Ian Bruce

Tailings and water management facilities are essential and integral components of mine and mill operations. They must be managed for the long term in order to ensure that safe and environmentally responsible stewardship is achieved. Toward this end, in 1998, The Mining Association of Canada (MAC) published A Guide to the Management of Tailings Facilities, which recommended the implementation of a tailings management framework (Figure 1) to integrate environmental and safety considerations into each stage of the life cycle of a tailings facility, from initial site selection and design, through construction and operation, to eventual decommissioning and closure. By February 2000 it was becoming apparent that while mining companies were making significant progress toward implementing and documenting tailings management systems, and integrating them with overall environmental management systems, further effort was warranted in their application at the operational level. In particular, a need was identified for further guidance in preparing manuals that outline procedures for the safe operation, maintenance and surveillance (OMS) of tailings and water management facilities.

May 1, 2002

By S. Vujic

The exploitation of stone (trachyte) at the ?Srebro? open pit mine, located on the northern slopes of the Fru?ka Gora National Park (Serbia) central area begun in 1964. Stone exploitation in this locality does not endanger the environment in an ecological sense, does not pose a threat to plants and animals, and apart from the terrain configuration changes, it did not leave behind permanent consequences to the environment. Projects for permanent cessation of mining operations and for land reclamation and spatial arrangement were completed in these circumstances. The paper gives a short review of the condition at the open pit mine; furthermore, the key problems and basic demands are presented, together with a concept of technical and biological land reclamation and the spatial arrangement of the mining complex. Keywords Open pit mine, land reclamation, spatial planning, spatial arrangement, National Park, Fru?ka Gora, Srebro.

Jan 1, 2011

By Jessica Barber

Problem ? Mining operations consistently need equipment that is available, and able to perform to its maximum potential ? The most difficult part of a Maintenance Manager?s job is often a lack of knowledge on how long their equipment has to last ? The short term view can lead to interim fixes that accumulate into larger problems ? It is always difficult to justify major overhauls and upgrades when there is pressure to meet mine plan production targets

May 1, 2008

By JeffreyS. Vipperman, Daniel R. Babich, EricR. Bauer

In response to the continuing problem of noise induced hearing loss NIHL among mine workers, the National Institute for Occupational Safety and Health NIOSH has conducted numerous noise surveys in coal preparation plants. The research, consisting of worker dose monitoring, task observations, and equipment noise profiling, was completed in eight separate preparation plants. Worker dose monitoring was conducted for three shifts in most cases. Workers experiencing higher than allowable doses were task-observed for one full shift to correlate dose to noise source(s). Finally, noise levels on all floors, and in lunchrooms and control rooms, were characterized. Results indicate that only workers who routinely spend a significant portion of their shift in the plants (away from the control rooms) are susceptible to overexposure from noise. Certain pieces of equipment (screens, centrifuges, sieve bends) are the loudest primary noise sources responsible for the worker noise exposures.

By R. Steele

In addition to compliance with government emissions and reporting requirements, mining and mineral processing companies are increasing energy efficiency to reduce costs and become more competitive in the global marketplace. One of the major obstacles to identifying opportunities for increased energy efficiency is the lack of readily available data on energy use, and more importantly the energy use linked to production data, that identify energy reduction opportunities. As well as energy reduction, mining and mineral processing companies often struggle with the prediction of energy use, and are often penalized for under or over forecasting. Once again, it is the lack of timely information that makes this prediction difficult. This paper looks at expanding the use of a Manufacturing Execution Systems by integrating with Energy Solutions. This will provide automatic, timely information, at a granularity that makes it easier to identify energy reduction opportunities, reduce energy costs, and better predict energy use in a mining and mineral processing operation.

Jan 1, 2011

By Forrest C. Neil, Clint J. Keifer

The pollution of our water supply, Lake Michigan, is a continuing threat so long as our overflows from combined sewers exist. The problems have become even more acute during recent years, due to the increase of paved area- which accelerates and enlarges the flows of storm water. After each storm, mixtures of raw sewage and storm water spill into our waterways. If the storm is too large for the drainage systems, the mixture backs up into our streets and basements. Under severe conditions, it may even become necessary to open the locks, and discharge the polluted water into Lake Michigan. Consider the scope of the problem, as shown in Figure 1. The area in which combined sewers exist is 375 square miles, located in the central parts of Chicago and 49 suburbs. There are an estimated 640 overflow outlets to the waterways, each requiring attention. The capacity of outlets tributary to the waterways has increased dramatically over the years. Each time a pocket of upstream flooding is drained into the channels, the problem of its rapid disposition increases. Another difficulty is that the bottom of our waterways is covered with a blanket of accumulated sludge, ranging in depth up to 3-feet. This material harms the water quality by depleting the supply of oxygen dissolved in the water ... a final

Jan 1, 1997

New Developments in Spirals and Spiral Plant Operations Records indicate that spiral separators have been utilised in mineral separation for over 100 years. The Spiral's predecessor, the sluice, has been in use for centuries in different forms and a spiral can be thought of as a sluice wound around a column. The spiral separator is distinguished from the straight sluice, and other flowing film separators, in uniquely introducing centrifugal motion. The elegance of the spiral concept was embraced due to significantly improved separation efficiencies, ease of operation and tolerance of variation in feed conditions. Advances in spiral technology have improved the metallurgical performance, modernised the materials of construction, increased unit capacities and simplified operation. These advances have ensured that spirals continue to play a major industry role amidst other advancing and competing technologies. Recent developments in spiral and spiral plant technology include: the launch of the VHG spiral model, specifically aimed at feeds with very high levels of high-density mineral particles; the introduction of a high capacity wash water spiral model; and innovations in feed stabilisation and control. Details of these developments are presented together with the resultant operational benefits including feed stabilisation, product control and improved metallurgical performances.

Sep 13, 2010

Were it simply a matter of extracting tin from the simple tin sulphide, the proposition would undoubtedly be simple enough. When, however, other valuable metallic sulphides are combined with the tin, and it is required to separate these intomarketable products, then the proposition becomes somewhat complex, and such is the case with the class of material of which I am about to write. The locality where it occurs is Howell, New South Wales, and chiefly at the Conrad Silver-Lead Mine. The tin sulphide occurs chemically alloyed with copper, iron and other metals associated with galena, pyrites, mispickel, blende and silver sulphide in varying proportions, and generally in a gangue of highly crystallised quartz.Several varieties of tin sulphides occur, and from the following analyses of three minerals, these being specimens specially selected free from foreign matters, it will be seen that the chemical composition is somewhat complex.

Jan 1, 1902

Cripple Creek and Victor Gold Mine is an epithermal gold deposit located in the Rocky Mountains of Colorado. Surface operations are continuing along with an expansion for an onsite mill to take place in the next couple of years. The surface pit is currently progressing downward from an oxidized zone into a transitional, more sulfide/ telluride-rich zone. Gold mineralization includes native gold, electrum, and tellurides. Cyanide heap leaching is the recovery process for the oxidized ore with the sulfide/telluride-rich ore to be processed at the new onsite mill. Ore characterization prior to mining is vital when there are two possible recovery processes. This characterization is dependent on geometallurgy. To identify the causes of the variability, multiple parameters are analyzed and assayed. These parameters are measured by a variety of analytical testwork. The analytical testwork provides measurements for the desired parameters. Geometallurgical models are developed for the parameters per recovery process, so estimations can be inserted into the resource model to optimize operations and recoveries.

Feb 27, 2013

By S. Sarac

Solving ventilation networks of natural splitting is a basic problem in mine ventilation. Several mathematical techniques are used to solve this problem. This paper proposes a new method which combines the advantages of both classical Hardy Cross method and unconstrained optimization techniques. The trials carried out on model networks have shown that the method offers some facilities in the analysis of mine ventilation networks. Keywords: Ventilation network analysis, Hardy Cross method, Steepest Descent method.

Jan 1, 2000

By B Lumsden, B Lacouture

"Red Dog is one of the largest zinc mines in the world both in terms of reserves and annual production. In 2013, Red Dog produced 551,300 mt of contained zinc and 96,700 mt of contained lead. The mine, which is located in Northwest Alaska, is a partnership between Teck Alaska Incorporated, the operator of the mine and NANA Regional Corporation Inc, the local land owner. The Aqqaluk deposit, which is the current source of ore, has an average grade of 15.8% Zn, 4.1% Pb and 73 g/t Ag with the main minerals being sphalerite, galena, pyrite, barite and quartz. Surveys of the zinc flotation circuit at Red Dog identified that a substantial amount of fully liberated, sub 20 micron sphalerite particles were being lost to final tailings. As a means of improving fine sphalerite recovery, a four month plant trial of magnetic conditioning was conducted in the zinc retreat circuit. Magnetic conditioning technology has already been commissioned in several concentrators around the world to agglomerate fine paramagnetic minerals, increasing their probability of bubble collision and recovery in a flotation cell. The results of the four month plant trial at Red Dog showed that at a high level of confidence, a 1% increase in zinc recovery or zinc recovery and zinc concentrate grade combined was achieved with magnetic conditioning. The resulting economic benefit, which is also at a high level of confidence, is significant to Red Dog and therefore, magnetic conditioning has been permanently incorporated into the Red Dog zinc flotation circuit.IntroductionRed Dog is the largest zinc mine in North America and represents approximately 29% of North American zinc concentrate production. The mine is located in northwest Alaska, approximately 100 miles north of the Arctic Circle and 50 miles inland from the Chukchi Sea. The remote location makes the mine accessible only by air or seasonally by ocean-going barges. Red Dog is a partnership between NANA Regional Corporation Inc, the land owner and Teck Alaska Incorporated, the operator of the mine."

Jan 1, 2016

The alkaline ethylenediamine tetra-acetic acid (EDTA) leach process for extracting tungsten from scheelite (CaW04) ores has been examined for the treatment of low grade (<0.5 per cent WO,) residue dumps. The process has been considerably simplified by applying solvent extraction directly to the leach liquor.Ammonium paratungstate is thereby produced in a one step process and this obviates the need to physically recover EDTA prior to recycling. This modified process should be an economical method of tungsten extraction.

Jan 1, 1983