Search Documents

By W. R. Byrnes

This project was initiated on October 1, 1980 and will be completed on December 31, 1983. The project was Initially approved and funded by the Office of Surface Mining and subsequently was moved to the jurisdiction of the Bureau of Mines. It was administered through the Indiana Mining and Mineral Resources Research Institute. The research was done to assess reforestation success and ultimate productivity for areas reclaimed under the Surface Mining Control and Reclamation Act of 1977 (P.L. 95-87). The Permanent Regulatory Program for implementation of P.L. 95-87 Includes provisions for revegetation that require seeding of ground cover plants to control erosion until permanent vegetation such as tree species Is established, and restoration of mined land to its original or better productivity. Much of the land to be surface-mined presently supports forest cover and it is anticipated that reconstructed minesoils will exhibit high productive potential for hardwood tree species. Hence, information was needed on compatibility of ground cover and tree seedlings when established concurrently as well as on revegetation success under postmining versus premining conditions.

Jan 1, 1983

By James M. Spear

The U.S. Bureau of Mines and the U.S. Geological Survey conducted a mineral survey of the Elk Creek RARE II area during the summer of 1981. The study area encompasses 18,900 acres [29.5 sq mi (7,680 ha)] along Elk Creek, 18 mi (30 km) southeast of Covello, California. No mineral resources were identified by the U.S. Bureau of Mines during this survey. Assay results of samples taken in this area indicate only trace amounts of manganese and chromium. No radioactive or fluorescent minerals were detected. No oil and gas, coal, or geothermal leases have been recorded for the study area.

Jan 1, 1982

By Herbert H. Einstein

Instability of rock slopes often occurs in the form of excessive movement of bodies that are bounded by discontinuities. The well known limit equilibrium analysis for wedges and blocks suffer, however, from procedural simplifications and from the basic deficiency of limit eguilibrium analysis--the rigid body assumption. Thus, stability analysis for 2-and 3-plane wedges with a wide range of additional features regarding failure modes and external forces have been developed. The deficiency, due to the rigid body assumption, was corrected by an approach that includes the effects or the in-situ stress field and of the stiffness of discontinuities. The final step in making limit equilibrium approaches more valid was achieved with the method of artificial supports which makes it possible to identify among all possible failure modes the critical one and to determine the corresponding factor of safety. The analytical development includes the creation of appropriate computer codes and routines for programmable pocket calculators.

Jan 1, 1979

By E. J. Peuraniemi

Oxidation of chalcopyrite concentrate and two low-iron copper mattes were studied using a laboratory scale laminar-flow furnace simulating the phenomena taking place in different zones of the reaction shaft of a flash smelting furnace. In the experiments, screened fractions were fed into the furnace and sampled after short reaction time intervals by quenching them into a water film. Experimental conditions included temperatures of 1100 and 1300°C with reaction gas oxygen contents from 21 to 75 vol.%. Samples were analysed chemically for Cu, Fe and S to define removal rate of sulphur. Optical and scanning electron microscopy with EDS-analyser were used to examine the samples. In this paper, oxidation kinetics as well as ignition of particles are discussed. Changes in particle morphology, size, and composition are viewed to closely define the proceeding of the oxidation, and, consequently, to compose a detailed model of dust formation and reaction mechanisms. Data obtained in the experiments broadens the knowledge of physical and chemical phenomena in flash reactions and serves as reference for computer simulations.

Jan 1, 2000

Electrical trailing cable used to power coal mining machinery is frequently damaged by tensile strain or crushing by mining machines running over the cable. A major problem is finding the exact location of a short or open in this cable so it may be repaired. A major problem is finding the exact location of a short or open in this cable so it may be repaired. FMC Corporation was awarded modification III to USBM Contract H0122011 to continue development and testing of cable fault locators, resulting in delivery of: 1. A prototype electrostatic/electromagnetic/ TDR transmitter and an electrostatic/electro-magnetic receiver sot that: o Locates cable faults by time domain reflectometry o Locates opens by detecting electrostatic signals o Locates shorts by electromagnetic coupling. 2. A prototype infrared detector and an infrared detector power supply that heats a shorted area by applying high current (at low voltage) and locating a short by infrared output. 3. Twelve production infrared detectors. 4. Detail drawings for all of the developed instruments.

Jan 1, 1973

By R. Stefanko

This study concerns itself with the effects of diesel exhaust on mine ventilation systems. The approach here consisted of the development of mathematical models for emissions, dilution, and dispersion of gaseous pollutants from diesels. The general scheme was to use partial differential equations to predict concentration growths. Specifically, the following situations were modeled: 1. A single stationary diesel engine working in a single roadway. 2. A single diesel engine moving with uniform velocity in a single roadway. 3. Multiple diesel engines moving continuously in a cycle in a roadway with appreciable leakage. 4 Multiple diesel engines moving continuously in a cycle in a roadway with little or no leakage. 5. Multiple diesel engines moving randomly in a roadway with uniform air velocity.

Jan 1, 1974

By G. Bylapudi, K. Mondal, J. Hirschi

ABSTRACT: Rock bolts are the main form of defence against rock falls in mines. Conditions under-ground are conducive to corrosion. A perception exists about American coal mines that bolt corrosion is not an issue, especially when bolts are fully grouted. This perception is not necessarily accurate due to the formation of micro-cracks as the resin sets and to subsequent rock movement that breaks the resin column’s continuity. Corrosion should be considered when designing rock bolt support in long-term excavations. This paper explores the problem of corrosion, outlines a method to determine the corrosion potential of bolts, and suggests ways to mitigate such effects.

Jan 1, 2010

By Robert Stefanko

The following tables contain the average, maximum and minimum power parameter levels for several mining machines. Power factor is listed only for defined transducer output regions. The reasons for the undefined areas are provided in the Instrumentation Chapter. Several maximum voltage drops are included, and are computed from the no load line-to-line voltage: Again, the drops are from measurements at the low side of the load center. The machines are: Continuous Miners; F6A Alpine 76AM Jeffrey (d-c) 8CM Joy 8CM (10CM) Joy 9CM-2AH Joy loam Joy CU-43-2H Joy 2 each CM26H Lee-Norse CM28E Lee-Norse Shuttle Cars; 18SC Joy 48S Torkar (a-c) 2 - 10SC Joys input to rectifier 2 - 16SC Joys input to rectifier

Jan 1, 1973

ENGINEERS AVAILABLE (Under this heading will be published notes sent to the Secretary of the Institute by members or other persons introduced by members.) Member, technical graduate, aged 36. Experienced copper metallurgist and mining geologist. Familiar also, through 15 years' broad practical experience, with mining, cyanidation, concentration (including oil flotation), metallurgical accounting, and mine and plant management. Best references. No. 237. Member, graduate engineer with 10 years' experience in malleable, gray -Iron, and steel, as chemist., metallographist, and metallurgist. Researches and investigations by laboratory methods and under works conditions. No objection to some routine. No. 243. Member, technical graduate, broad experience in coal, oil, and clay. Will go anywhere as mining geologist after Sept. 1, 1915. No. 244. Member, technical graduate, aged 30, married, with over 10 years' experience as chemist, engineer on construction, superintendent and general superintendent of bituminous coal and coke plants. SpeaksSpanish. References. No. 245. Member, open for engagement as mine safety inspector or as superintendent of bituminous coal mine. No. 246. Member, graduate mining engineer, with five years' experience in coal mining as mining engineer, construction engineer, pit boss, and superintendent, open for engagement. Best references. No. 247.

Jan 9, 1915

By C. Lurie

This final report describes the work performed by Gulton Battery Corporation under USBM Contract No. HO-112033, entitled "Research and Development on Lithium-Nickel Fluoride Batteries For Mint Life Support Equipment". The lithium-nickel fluoride couple was chosen For this investigation because of its high theoretical energy density (626 Wh/lb), its ability to operate at ambient temperatures and the fact that it showed promise as a secondary system. The theoretical energy density of the lithium-nickel fluoride couple is ten times greater than that of the widely used lead-acid battery and three times greater than the silver-zinc battery which has the highest theoretical energy density of the commercially available secondary systems. The experimental program first evaluated the cell components individually. The results of these studies then formed the basis for investigations of cell performance using experimental three-plate cells. These cells consisted of one nickel-fluoride and two lithium electrodes. All work was performed in a glove box under an argon atmosphere which was sufficiently pure to maintain the shiny appearance on freshly prepared lithium surfaces. The major portion of the work effort was concerned with the nickel fluoride electrode. Binder, conductive diluent, fabrication technique, as well as the nickel fluoride active material itself, were considered. Criteria for binder materials were established and six classes of materials encompassing thirteen binders were evaluated. The candidate materials were initially screened for appropriate chemical and physical properties and finally evaluated in three.-plate cells, Two epoxy powders emerged as the most promising binders. Two types of conductive diluent were evaluated. The first is a carbon black of low bulk density and high surface area. This material is a good conductive diluent; however, electrodes fabricated with it lacked good mechanical strength. It was hypothesized that a uni¬form, small particle size, low specific surface area would improve the mechanical properties of the electrodes. Therefore, two samples of graphicic materials, milled to uniform powders in the one-to-ten micron range were evaluated. Electrodes prepared with the graphitic materials had superior mechanical properties, However, their electrical performance was significantly poorer and voltage losses of 0.2 to 0.3 volts were observed. Several electrolyte solutions were evaluated. N-Methyl-2-Pyrrolidone was tested but found to be incompatible in the presence of lithium. Lithium perchlorate, lithium hexafluoroarsenate, and lithium bromide were tested as two-component electrolytes in propylene carbonate solvent and their performance compared with that of the single electrolyte solutions, Lithium perchlorate gave the best performance. Lithium hexafluoroarsenate was also evaluated in methyl formate and appears to give equivalent performance. The lithium perchlorate-propylene carbonate system is preferred as it is easier to handle and less expensive.

Jan 1, 1973

By George Meadows

Consultation and Accommodation Introductions Consultation -Best Practices The Role of Negotiations The HVC Experience Summary / Conclusions The Challenge Meeting legal and policy obligations to consult while adhering to project priorities, timelines and budgets Defining who needs to be consulted, by whom, and ?how much?? Accommodation ?who is responsible and what is the appropriate scope? Social License -establishing positive working relationships with First Nations involved in project review / approvals / implementation in a manner that advances the interests of all parties

May 1, 2010

Prepare ATF Report of Theft or Loss (ATF Form 5400.5). A Report of Theft or Loss - Explosives Materials must be prepared when it is discovered that explosive materials are missing from inventory. Submit the original to the U.S. Bomb Data Center and keep a copy for your records. The form can be obtained from the ATF Distribution Center or from www.atf.gov. Although the U.S. Bomb Data Center should be notified as soon as possible, Federal law requires notification within 24 hours of the discovery. A full inventory check is also highly recommended (but not required) to locate missing explosives and to prevent future losses.

Jan 1, 2008

By Dennis J. Grigal

The goal of the program is to develop a dust collector system mounted on a ranging drum or arm shearer which will: 1) reduce the respirable dust level of the shearer operator by at least 75 percent; 2) be easily and economically mounted on an existing shearer; and 3) will not, through modifications to the shearer, reduce its safety or productive capability. The development program consists of three phases covering the activities of the design of the dust collector system, fabricating and installing it on the ranging arm or drum shearer, and conducting underground field tests on the modified mining machine.

Jan 1, 1980

By Pierre Laliberté

Introduction ??Mine ventilation is a major consumer of power in underground mining, including air heating (winter) and air conditioning (deep mines). ??Any advances, including the development of low emission vehicles, that can improve underground air quality can reduce ventilation demand, and likewise reduce costs and energy consumption, including their associated greenhouse gas emissions.

Nov 1, 2011

By Robert L. Lagace

This final report documents the work dune by Arthur D. Little, Inc. (ADL) on behalf of the U.S. Bureau of Mines, Pittsburgh Mining and Safety Research Center (PMSRC), on Contract H0122026 (which began in August of 1971). Under this contract ADL provided technical assistance to the Bureau on a task basis on virtually all aspects of the Bureau's programs related to present and planned emergency and operational communications and miner location systems for underground coal mines. The work consisted of independent investigations, analyses, experiments, breadboard and prototype hardware development, workshops and technology transfer seminars on mine communications, and on-going evaluations and guidance related to the Bureau's contracted programs on electromagnetic noise, mine communications systems, and trapped miner location. This final report documents the work in two volumes, Volume I, "Emergency and Operational Mine Communications," and Volume II, "Seismic Detection and Location of Isolated Miners." The Tables of Contents of both Volumes are included in each Volume. Phase I of the contract was devoted to performing an in-depth assessment of electromagnetic noise measurements taken by several contractors and other investigators, and then defining a new noise measurement program and instrumentation system tailored to obtain the necessary but missing noise data. These data are required for use in the design of new emergency and operational communication systems. This work, and the follow-on coordination and guidance activities of ADL on this noise measurement program in subsequent phases of the contract, are treated in Part One of Volume I.

Jan 1, 1974

By William G. Pariseau

The research reported here concerns ground control in multi-seam mining and relates mainly to the analysis of stress about multi-seam room and pillar mines. The two variables of most concern are distance between seams and alignment of pillars between seams. The first year results of the two year investigation apply to the development phase of mining when the extraction is typically less than 50 percent. The second year effort is concentrated on retreat mining and barrier pillar safety when the extraction is typically greater than 50%. The procedures in both cases are readily applicable to more than two seams. Although two seam mines are the most frequent type of multi-seam operations, because of the potential for three seam operations in the Western United States, a number of three seam development analyses are also presented. The results enable one to make a rapid assessment of stability of rooms and pillars during production and barrier pillar size during extraction of adjacent panels. In the event of low safety factors, more site-specific analyses can be undertaken.

Jan 1, 1983

The above referenced contract between Badger Manufacturing Corporation and the U. S Bureau of Mines was executed June 30, 1975, as a result of the request for proposals for innovative machine concepts. We selected the cutting machine category because of the obvious lack of technical progress in this field for many years: Phase I of the contract required blasting fragmentation tests to determine proper blasting patterns for use with the auger-type kerf cutting machine. Phase II required design concept development for a machine capable of cutting a circular void as an aid to blasting.

Jan 1, 1975

By Lucia Kuizon

The Cactus Springs Roadless Area Review and Evaluation (RARE II) study area (No. A5188) comprises 12,800 net acres (5,180 ha) in San Bernardino National Forest in west central Riverside County, California, about 20 air miles (32 km) southeast of Palm Springs. Mineral investigations are made by the U.S. Bureau of Mines on National Forest lands identified as Further Planning Areas in the RARE II program. The Bureau of Mines reviewed literature, mining claim records, and production files; examined the study area; and mapped and sampled mineral properties where appropriate.

Jan 1, 1983

By Fredrick L. Johnson

The Jerry Peak, Jerry Peak West, and Boulder Creep: Wilderness Study Areas contain no identified mineral resources. Two workings, a 20-ft-long adit and a pit, were found in Paleozoic, brecciated, limonitic jasperoid in the east part of the Jerry Peak Wilderness Study Area (WSA), but no significant metallic mineral values were noted. Lenses and pods of quartz containing copper minerals occur in Paleozoic sedimentary rocks 1/2 mi north of the Jerry Peak West WSA. Similar rocks crop out along Pine Creep: in that study area but no copper-bearing quartz lenses were found.

Jan 1, 1984

By G. A. Fenton, A. Vervoort, M. Alvarez Grima

"High-risk underwater mining operations necessitate characterizing spatial heterogeneity and resource uncertainty. Local average subdivision is a method of simulating spatial deposit variability inside a cell through a sequence of discretization stages, during which a cell is further subdivided into four or eight cells. New developments are presented to validate simulated deposit models and deal with point measurements of geotechnical and ore-grade properties. This paper illustrates the relevance of translating spatial deposit variability into financial or operational performance indicators during underwater resource exploitation. Two synthetic case studies highlight the challenges of underwater mining in relation to production plans and equipment selection.RÉSUMÉ Les opérations d’extraction minière subaquatique à risque élevé exigent une caractérisation de l’hétérogénéité spatiale et de l’incertitude de la ressource. La moyenne locale de subdivision est une méthode de simuler la variabilité spatiale du gisement dans une cellule par une séquence d’étapes de discrétisation durant lesquelles une cellule est subdivisée en quatre ou huit cellules. De nouveaux développements sont présentés afin de valider les modèles de simulation des gisements et de traiter des mesures ponctuelles des propriétés géotechniques et de teneur du minerai. Le présent article illustre la pertinence de traduire la variabilité spatiale du gisement en indicateurs de rendement financier ou opérationnel durant l’exploitation subaquatique de la ressource. Deux cas synthétiques soulignent les défis de l’exploitation minière subaquatique par rapport aux plans de production et de choix des équipements."

Jan 1, 2015