Search Documents

At the Orieco mine quartz veins carrying sulphides were localized in parts of an extensive fault zone in the Mathinna Beds during late Middle Palaeozoic mineralization.These deposits were subsequently exposed, and oxidation of the sulphides by percolating groundwaters resulted in the formation of gossans at the surface, and replacement close to the permanent water table of the more soluble sulphides by copper sulphides (chalcocite, coveIlite). A restricted zone containing copper oxides (cuprite, tenorite), copper carbonates (malachite, azurite), iron arsenates (scorodite, pharmacosiderite) and possibly rare copper sulphates occurred above the water table.The renewed oxidation of these deposits following mine development has been facilitated by the ready circulation of air and water combined with the formation of large free surfaces ideal for evaporation of aqueous solutions. Under these new conditions of high initial sulphate concentration, low pH, and relatively high Eh, the previously formed mineral assemblage is unstable and numerous Cu (Fe,Zn)-sulphates and Fe (Cu,Pb)-arsenates are presently forming in fractures in the fault zone and on the adit and stope surfaces for some considerable distance from the Sulphide-rich ore shoots. The observed spatial sequence of the major sulphates with respect to the sulphide-rich zones (Le. chalcanthite-antleritebrochantite and langite) is consistent with decreasing sulphate concentration and increasing pH away from the oxidizing sulphides.

Jan 1, 1970

By Franklin M. Grynkewicz

The subject of bearing pile performance installed by vibratory hammers has been a matter of increasing study and continued controversy. A recent case study from a major bridge replacement project is discussed which provides encouraging data on the use of vibratory pile hammers as a primary means of pile installation and also presents the problems associated with its general acceptance. The bridge project case study foundations consisted of HP 14 x 89 pile sections, designed to develop capacity primarily in friction. Preliminary tip elevations were determined by traditional static analyses. Production pile installation was performed using an IHC S-70 Hydro-Hammer. Driving criteria and final production pile tip elevations were determined after preliminary indicator pile drive tests and static load test results at bridge pier cofferdam locations. Based on impact driven production pile performance, the Contractor wished to investigate vibratory driven piles as a means to accelerate construction schedule. Dynamic pile testing procedures were used as the primary measurement tool and test results were compared to the production pile drive records and prior static load tests. Field testing consisted of driving and monitoring with the PDA impact driven piles to the design tip elevation. Three vibratory driven piles were installed to the same tip elevation and immediately subjected to impact driving and dynamic testing to compare dynamic pile resistance. The results indicated that the site soil conditions were favorable for vibratory pile hammer installation. Recommendations and procedures for proceeding with vibratory hammer pile installation were presented to the Owner. These procedures included quality control in conformance with latest AASHTO recommendations. The Owner, in spite of the site specific data base and QA/QC procedures, would not accept vibratory pile hammer installation, due to the absence of precedence. It is concluded that for vibratory methods to become accepted a rational method of analysis, design and field QA/QC procedures requires development. In addition, the engineering community and Owners/Agencies must be more open to alternate methods of foundation construction. The continued development of dynamic methods of monitoring vibratory pile installation is considered to be key to the general acceptance of this installation procedure.

Jan 1, 1991

By Andrey V. Tarasov

To carry out a physicochemical substantiation of a transition to ?soft? modes of reduction of calcine obtained by desulfurizing roasting of nickel concentrate produced as a result of copper-nickel converter matte separation in a nickel anode production circuit, an analysis has been conducted of the macrokinetic behavior of actual calcine samples in the presence of gaseous H2-CO mixtures and solid reductant additives. Within a temperature range of 900°C to 1100°C the main regularities typical of the calcine reduction process with individual gases (H2, CO) also take place when using a gaseous mixture. Under the conditions of low-temperature (900°C to 1000°C) nickel oxide reduction with products of fuel oil conversion in the presence of coke, the role of the latter is insignificant from the technological viewpoint. As a result of the present investigations, we have obtained analytical expressions of macrokinetic parameters of the reaction interaction within the [NiO] calcine-H2-CO-C-CO2-H2O-O2-N2 system.

Jan 1, 2005

By Tammy G. R. Portela

A comparative characterization of the dimensional and mechanical properties as well as structural aspects of two different types of fibers extracted from the leaves and petioles of the buriti palm tree was performed. A statistical analysis revealed that both types of fibers present a significant dispersion in length and equivalent diameter. However, the corresponding intervals of dimensional variation are sensibly different. The tensile properties showed that both types of fibers display a tendency of higher strength for smaller diameters. Moreover, the fibers extracted from the leaves depict a comparatively lower strength. By contrast, the fibers from the petiole present an average strength sufficiently high for the use as reinforcement of polymeric composites. The structural aspects of tensile-rupture fibers, characterized by scanning electron microscopy, showed marked distinction in the microstructure and fiber behavior of both types of investigated fibers. This could explain the differences in mechanical behavior

Jan 1, 2010

By Michael J. Sapko, Gregory M. Green, Kenneth L. Cashdollar

The National Institute for Occupational Safety and Health (NIOSH) and the Mine Safety and Health Administration (MSHA) conducted a joint survey to determine the range of coal particle sizes found in dust samples collected from intake airways of US coal mines. The last comprehensive survey of this type was performed in the 1920s. The size of the coal dust is relevant to the amount of rock dust required to inert the coal dust, with more rock dust needed to inert finer sizes of coal dust. Dust samples were collected by MSHA inspectors from several mines in each of MSHA's 10 bituminous Coal Mine Safety and Health Districts. Samples were normally collected in several intakes at each mine. The laboratory analysis procedures included acid leaching of the sample to remove the limestone rock dust, sonic sieving to determine the dust size, and low-temperature ashing of the sieved fractions to correct for any remaining incombustible matter. The results indicate that particle sizes of mine coal dust in intake airways are finer than those measured in the 1920s. This finer size coal dust in intake airways would require more incombustible matter to be effectively inerted than the 65% incombustible specified in current regulations.

By T D. Sullivan

Risk lies at the heart of all mining and nowhere more so than in pit slope design. Mining is principally about two areas of risk; safety and economics. This paper addresses the main elements of pit slope design and presents a view of the state of the art in terms of safety, design, prediction of performance, success and pit slope management. There has been a recent trend for serious injury and fatalities due to stability in open pit mines. The causes and contributing factors are analysed in relation to geotechnical knowledge, pit slope design and management. Currently there is no standard classification system for mine slope designs and it is considered doubtful if a universal system is possible. Designs are usually formulated in accordance with many different methodologies, various engineering principals and a number of different philosophical approaches, with results often presented in terms of Factors of Safety or Probabilities of Failure. However wide experience has demonstrated that even with apparently detailed engineering investigation and analysis at Feasibility Level, at the Operating Stage mine slope angles are regularly subject to large changes. The general experience is that these changes are ± 5° and 16° overall, which is considerably outside the accepted order of accuracy. For large deep mines these are huge changes and represent significant risks to the operations. The current state of practice in pit slope design is examined for two stages, feasibility and operating.

Jan 1, 2006

By Fred S. Karn

Inhibitors are used in coal mines as a precaution against accidental dust explosions. Although rock dust is the usual inhibitor many others have been tested. To facilitate testing a screening process using laser irradiation was proposed. The procedure includes irradiation of a coal-dust mixture followed by mass-spectrometric analysis of the evolved gases and an evaluation of the flammability characteristics of the gases. Carbonate-type inhibitors decreased the percentage of combustibles in the gases generated and inhibitors like NaCI (thermally stable salts) decreased the total gas generated. A suitable test procedure did not result from the investigation, demonstrating the inadequacy of fast heating, non-combustive techniques in rating inhibitors of coal dust explosions.

Jan 1, 1973

By Thomas J. Peters

In 1979 and 1980, the U.S. Bureau of Mines and U.S. Geological Survey conducted a mineral survey of the 15,600 acre (6,310 ha) Freel Peak RARE II area (No. 5271) in the Lake Tahoe Management Unit. This study by the Bureau of Mines indicates that potential for economic mineral resources in the area is slight. The only mineralized structures in the area consists of two quartz veins. One quartz vein, at the Mountain Top Mine (fig. 1), located by Fred Denner in 1932, is estimated to contain 2,000 tons (1,800 t) of silver and copper-bearing resources. Chip samples from the vein averaged 0.61 oz silver per ton (20.91 g/t), and 1.59 percent copper. The narrow vein is not economically mineable. The other quartz vein is poorly exposed and contains traces of molybdenum. A second reported molybdenum occurrence could not be substantiated.

Jan 1, 1982

By Juan M. Antorena

A pile driving and testing program was undertaken to evaluate installation procedures, assess capacity, particularly in uplift, of 360- and 460-mm (14- and 18-inch) square prestressed concrete piles and provide foundation design parameters for the New Mid-Point Bridge project in Fort Myers, Florida. Nine piles were dynamically monitored during installation, and six piles were monitored during restrike driving to evaluate pile drivability and uplift and bearing capacity including time related capacity increases due to soil "set-up". In addition, two static load tests (tension and compression) were performed to calibrated the results obtain during the dynamic testing. This paper presents descriptions of the pile driving testing program along with findings regarding pile uplift and compression capacities from the static load testing, pile capacities from dynamic testing (CAPWAP® analyses), soil-pile adhesion values, wave equation factors, soil strength vs. time dependency, foundation design (anticipated pile tip elevation) and pile driving recommendations.

Jan 1, 1995

By Donald O. Capstick

The U.S. Bureau of Mines conducted an inventory of the prospects and mineral resources in the Scodies RARE II area (No. 5212) in 1982. No mineral production is recorded from the area, and no mines are being developed. The Scodies RARE II area is comprised primarily of light colored granodiorite with minor inclusions of mafic granitic rocks. Late stage differentiates of magmas resulted in quartz veins and pods. Metasedimentary rocks which have been mineralized in some parts of the Sierra Nevada were not observed within the study area during this investigation but small inclusions have been reported.

Jan 1, 1983

By Thomas W. Camm

The U.S. Bureau of Mines has developed a system for estimating mining and processing costs as a function of process feed rate with the objective of applying this system to abandoned mine tailings and to evaluate the benefits, if any, of metal recovery. Cost analysis was applied to the mine wastes of Smelterville Flats: an extensive area of mine tailings in the Bunker Hill Superfund Site with high concentrations of lead, zinc, and other sulfide minerals. Results from previous site characterization and metallurgical processing studies were used as the input for the cost analysis. This analysis indicated that processing this site at an optimum production rate of 3,500 short tons per day (st/d) could generate a positive cash flow.

Jan 1, 1993

By Peter G. Groer

The commonly used exact methods (1-2) to determine the WL measure the total a activity or the total number of a counts during three preselected time periods. Due to the half-lives involved (TRaB = 26.8 min, TRaC = 19.7) I these methods take 3S minutes to complete the a activity Ra measurements. Methods using the total a counts, obtained at times less than about one RaB half-life after the end of sampling run into statistical 214 problems. These methods are almost blind to RaB (Pb214) as a consequence of its relatively long half period (see above) and the fact that RaB is a ß emitter. The way out of this dilema is to measure RaB directly through its ß activity. Since RaB's daughter Rae (Bi214) is also a ß emitter, the two f3 spectra have to be separated to obtain RaB alone. How this is accomplished 1s described in subsequent sections describing the theory of the IWLM and its calibration. 2.0 THEORY The IWLM samples air for two minutes and counts this airs ample for two minutes starting 3 sec after the end of the sampling period. The instrument has three channels. The lower a channel, the upper a channel, and one ß channel. The total RaA counts observed are accumulated in the lower a channel, the total RaC? counts are stored in the upper a channel. The total ß counts from RaB and RaC are recorded in the ß channel. These three quantities are functions of NA, NB, and NC, the unknown concentrations

Jan 1, 1975

By Vinit Mody

The belt conveyor is one of the major pieces of equipment for transferring bulk material in mining operations. However, considerable amount of respirable dust may be generated whenever the bulk material is loaded, dumped, or transferred. This report identifies and evaluates various dust control technolgies applicable to belt conveyors, and describes how an integrated systems approach can reduce dust emissions at a transfer point. Phase I of the program consisted of literature search and a critical evaluation of various dust control technologies. The work established that a comprehensive approach to calculating exhaust volumes for dust collection system does not exist. The parameters that affect the wet dust suppression efficiency were also reviewed. Based on the Phase I work, bulk material handling system and dry dust collection or wet dust suppression systems were designed and installed at a number of transfer points in a limestone processing facility, a surface mine selected as a field test site. Field test data were used to determine the validity of various exhaust volume calculations at the different transfer points. The field test data also formed the basis for the evaluations of the relative effectiveness of commercially available and wet dust suppression systems in controlling respirable dust emissions.

Jan 1, 1984

By Stephen C. Tadolini, Raymond A. Mazzoni

The International Ground Control Conference in Mining has always provided an open forum for the publication, presentation, discussion, and often heated debate on roof bolting systems mostly with attention to how, when, and why they work. During the last 24 Conferences at least 170 papers have been presented by International Experts on these “simple” devices that range in length from 30-inches to 20 ft and from 5/8 to 2 inches in diameter. Roof bolts are primarily mechanically anchored, glued, cemented, or driven. Bolts are placed vertically, angled, or tied together with special fixtures (trusses and slings). They have been termed active, passive, stick-slip, and several other descriptive acronyms or mining slang expressions. This retrospective paper will present the changes in bolt types and usage, point out some of the biggest myths and hail the most significant advances (according to the authors’ opinions of course).

By D. McBride

Representative samples are required from process streams in order to accurately measure chemical and physical characteristics. This information can then be used by process operators and metallurgists to evaluate the process and effect control actions for the operation. The capture and presentation of representative samples can be critical to measuring values, such as elemental analysis and particle size, with on-line or near-stream analyzers. A comprehensive multi-physics model has been developed and used to better understand the effects of slurry flow and particle segregation under certain operating parameters. An algebraic slip model coupled with a free surface algorithm is used to track motion and position of particles and phases within a specified geometry.

Jan 1, 2009

By R. Grimard, M. Gamache, L. -P. Bigras, P. Cohen

This paper describes a real-time fleet management system for an undergroun mine. Dispatching, routing and scheduling are handled simultaneously, taking into account the mine status, operational constraints and vehicle location information. Each assignment decision takes into account the traffic on the road segments of the mine network, whether road segments are bi-directional or uni-directional, and ensures that each LHD (load-haul-dump) vehicle arrives at loading and dumping points with the correct orientation. Such a system can be used either as a simulation tool for strategic planning or as a real-time managing and optimizing system for operations. In the simulation mode, the system can accurately estimate the impact on productivity of decisions such as the development of waiting areas (bays, sidings), or the addition (elimination) of vehicles to the fleet in operation. When used for real-time dispatching, routing and scheduling of vehicles, the system can optimize production with respect to various assignment criteria such as cycle-time minimization or deviation from a target production plan.

Jan 1, 2004

By Aloke Verma, R. Singh, S. Jana, C. Sawmliana, P. Pal Roy

On July 21, 2004, a trial blast using electronic detonators was conducted in India for the first time in an opencast mine at Pundi-E Quarry of TISCO, West Bokaro. Orica-IEL conducted the test using electronic detonators. To provide necessary technical feedback on wider applicability, CMRI scientists also participated in the trial blast.

Jan 1, 2006

By D. V. Karandikar

Contiguous bored piles have been used in the past for retaining the sides of deep excavation. An innovative version of this method was adopted successfully in two prestigeous projects in Bombay in which in a very constricted and congested locality, adjoining seashore at Walkeshwar, 14 m deep excavations with vertical sides were required. 600 mm dia bored cast-in-situ piles were first installed at 1.2 m c/c and subsequently as the excavation proceeded, they were tied to cast-in-situ RCC waling beams. The shear connectors to the beams were pre-fixed to the pile reinforcing cage at specified depths. The pile / waling beam system was anchored into the ground by installing inclined prestressed cable anchors at the designed depths. The waling beams were also used to support the brickwalls, which formed the required backup wall for fixing the tiled water proofing system. Catch-drains were installed behind the brickwalls for relieving the ground water pressure and thus ensuring a very economic design. The adequacy of the system was proven in that where the system was not installed in time, failure of the sides occurred during monsoon. Whereas in the areas where the above retaining system was installed, there were no problems inspite of heavy monsoon and surcharge of construction materials and equipment. The system became a very effective and economic alternative to an anchored diaphragm wall. The paper presents the case studies of these two projects.

Jan 1, 1996

By William F. Daly, William H. Hansmire

Installation of initial tunnel support is often the most uncertain element of work in the design of, and a contractor bidding on, construction of a rock tunnel. The risks the construction contractor and owner assume are delineated to a great extent in the technical specifications portion of the contract documents. It is intended that this paper identify current practices for specifying initial tunnel support and the impacts each case has on the assignment of risks associated with providing the initial tunnel support. Examples of recently completed tunnel designs are given.

Jan 1, 1985

By M. Pernot

A 12 m-deep excavation has to be perfomed in the Shanghai soft clay to install an underground electric substation. This article was originally intended to study the behaviour of the wall, the excavation bottom and the surrounding ground during the excavation. Since the works are behind schedule, and the data referring to the excavations are not, therefore, available, the article is limited to a presentation of the analysis methods that we envisaged for the study of the behaviour of the excavation.

Jan 1, 2010