Search Documents

By Steven E. Mischler, Jon C. Volkwein

A diesel particulate matter analyzer capable of direct, real-time measurement of engine exhaust particulate is necessary to effectively institute source control technology currently being used on diesel equipment and to ensure that the control measures are working. To investigate the potential of a differential pressure monitor to measure diesel particulate matter in undiluted exhaust, samples were collected from three different diesel engines-Kubota, Isuzu, and Deutz-running under 12 different RPM and load scenarios. These measurements were compared to elemental carbon concentrations in the sampled exhaust as determined by using the NIOSH 5040 analytical method. Elemental carbon is used as a surrogate measurement for diesel particulate matter. The results of the two data sets were then compared using a linear regression analysis. The coefficient of determination (or R2) was calculated to be 0.98, 0.94, and 0.74 for the Kubota, Deutz, and Isuzu engines, respectively. R2 values of this magnitude indicate that this method can be successful in estimating elemental carbon emissions in the engines tested. In addition, for replicate samples, the coefficient of variation ranged from 7.1% to 10.2% with an average of 8.5%. These data indicate that this method could prove useful to mechanics as they work to maintain engines and DPM control technologies.

By G. Miller

The design of solvent extraction plants has been generally based on the assumption of steady operating conditions in both the settler and the mixers. Recent experience with both large and small plants has shown that this is not the case. Mixer transients include start up aqueous locking and partial phase separation in secondary mixers. Both of these lead to either reduced plant capacity or overflow of upstream mixers. Analysis of the hydraulic pressure profiles has generated new design methods to eliminate the effects of the partial or complete phase separation. Further, changes to the method of specification and selection of both primary and secondary mixers have been made to eliminate the onset of partial separation during operation. Observation of settler operation has shown that it is also a dynamic process, even under ‘steady state’ conditions. Four different transient phenomena have been identified that lead to internal circulating flows, poor disengagement of fine secondary haze, and erratic and high entrainment levels in the discharges. A first approximation analysis has shown that there are significant pressure differentials within settlers and these change along the length and with phase separation rates. A technique to control the effects of these transients has been developed which allows plant performance to be improved beyond ‘standard’ expectations. The design and selection of the settler internals is described.

Jan 1, 2001

By James W. Stewart, A. C. Colvine

Introduction Precambrian shield terrains the world over are experiencing an unprecedented level of concerted exploration for lode gold deposits. Reasons for this include: • The increase in the price of gold (following 40 years at $1.13/g or $35 per oz) has transformed targets that were once unattractive into viable exploration propositions. • The relatively suppressed market for other metals produced from shields (base metals, nickel, iron, and uranium) has further focused exploration attention on gold. • The preeminence of gold production from rocks of early Precambrian age, as shown in Fig. 1. • The relatively high grade of gold in these mines (averaging about 10 Wt or 0.29 oz per st) permits profitable extraction even under depressed gold prices. A number of these mines have been in continuous operation for more than 50 years. • The recent discovery of the major Hemlo deposit, in well exposed rocks adjacent to the Trans Canada Highway, has had a world-wide impact. This demonstrates that a major new deposit can be found even in an accessible, well exposed area of a shield; gold mineralization is susceptible to rational exploration; and new target types for gold exploration exist. This paper reviews exploration activity for gold in shield terrains worldwide (Fig. 2), excluding Early Proterozoic paleoplacers of the Witwatersrand type. Emphasis is on the Archean, which is traditionally the most productive part of the Precambrian shields. There is also an emphasis on the Canadian shield (Fig. 3) because of its vast areal extent and exceptionally broad range of mineralization styles. Geological Approach A basic problem exists in gold exploration when compared to exploration for base metal massive sulfides that predominated during the 1960s and 1970s. Gold concentrations cannot usually be detected by airborne geophysical instruments. The majority of massive sulfide deposits were detected using airborne electromagnetic detectors and magnetometers. A full 75% of Canadian gold discoveries can be credited to surface prospecting. The percentage is even higher in other countries. This observation allows for great optimism for two reasons: • Large areas of shield terrain are obscured by either surficial deposits (glacial tills, clays, and desert sands) or deep surface weathering. This makes them inaccessible to prospectors. Logic dictates that such obscured areas should have the same potential for gold concentration as has exposed bedrock. • The Hemlo style of mineralization, a roughly tabular ore body where gold is associated with disseminated sulfides, is different from the traditional prospecting target. The gold is hosted by discrete quartz veins. While it is true that limited discoveries were made at Hemlo more than 30 years ago, and this style of mineralization is present elsewhere, recent

Jan 12, 1984

By Pengfu Tan

A thermodynamic model of KIVCET lead smelting process has been developed. The model has the capability to predict the distribution behaviors of Pb, Zn, Fe, S, O, As, and heat balance in KIVCET direct lead smelting furnace. The compositions of lead bullion, matte, slag and gaseous phases, and heat balance are calculated. The effect of the ratio between oxygen and feed on the chemistry of the smelt and heat balance of the coke checker has been simulated and discussed. The thermodynamic model also helps to understand the tapping issue of the lead bullion. In this paper, some applications of this model in the industry have been presented.

Jan 1, 2006

By Franklin J. Stermole

L. Alan Weakly, member SME, is a senior staff engineer, Exxon Co. Weakly chaired a Mining Engineering committee formed to solicit materials for six planned "personal skills" articles, to be used in ME this year. What follows are Weakly's introductory comments to the series. Upon graduation from college several years ago, I thought that I was sufficiently prepared to embark in my chosen profession. A short time later I realized that several years of on-the-job training was going to be required before I could use my technical training effectively. It never occurred to me that, professionally, I was seriously lacking in any other skills. My spelling could use a little upgrading, but this was not a serious deficiency. I have been very fortunate to have had two employers that recognized that their engineering professionals did lack other skills and made every effort to give them training to correct these deficiencies. The skills I am referring to are those in administration and interpersonal relationships. Most mining engineers and geologists receive very little, if any, college training in these areas. In addition, many companies do not provide this training and many mining engineers and geologists are unaware of their deficiencies. It is for this reason the subject of personal skills development is being introduced in Mining Engineering. The mining engineer or geologist can pursue one of two basic career directions, managerial or technical. In today's technically sophisticated society and highly competitive business climate, both orientations require administrative and interpersonal skills. Most of us are technically qualified and we continue to upgrade our technical skills. But many studies indicate that we, as a group, are significantly weaker in administrative and interpersonal skills than other professional groups. In addition, these studies indicate that engineers, in general, take longer to reach managerial levels and fewer do so. This series in Mining Engineering, then, should help readers strengthen and broaden their professional capabilities. In all industries, including mining and petroleum, economic analysis of potential investment projects is done to select the projects that will give maximum future value from the investment of available capital. Rather than looking directly at the future values to be generated by investing capital in alternate ways for economic decisions, evaluators usually use either rate of return, present value, annual value, a profit to investment ratio, or various break even analysis results to reach economic analysis decisions in evaluating alternative investments. Alternative economic evaluation techniques are used in industry to properly analyze the economic potential of various investment projects. "Discounted Cash Flow" analysis is the phrase commonly used to describe these techniques. Whether you want to analyze projects in mineral, petroleum, real estate, refining, pipe-line transportation, or any other industry, proper application of discounted cash flow analysis techniques enables you to fairly compare the economic potential of alternative projects as well or better than you can using any other project evaluation approaches. It should be pointed out that investment analysis generally involves more than economic analysis. Financial and intangible considerations sometimes are as important or more important to investment decision-making than economic considerations. Economic analysis refers to evaluation of the profit generating potential of projects, that is selecting which alternative projects will generate maximum future value possible from available investment capital. Financial analysis, on the other hand, relates to analysis of where money is going to come from to finance various projects. Regardless of the economic potential of a project, if financial analysis indicates that we cannot finance the project, it likely will be shelved for financial reasons even though it may be economically satisfactory. Many evaluators use the terms "economic analysis" and "financial analysis" interchangeably, but this author considers that to be undesirable. Intangible analysis relates to project factors that are difficult to quantify in

Jan 2, 1984

By S. E. Olsen, M. Tangstad

The main source of Mn in raw materials for SiMn production is Mn-ore and Mn-rich slag from the high carbon FeMn production. The amount of slag per tonne of SiMn metal is mainly determined by the ore/slag ratio. Increasing share of FeMn slag at expense of Mn-ore will lead to larger slag/metal ratio in the SiMn process. High volume of slag leads to an increased consumption of energy and probably to higher losses of metal inclusions in the final slag. Excavation of a SiMn furnace has shown that only modest pre-reduction of Mn-ore with CO gas seems to be obtained. Nearly all reduction of MnO was finished at the top of the cokebed. Dissolution and reduction of quartz obviously takes place in the cokebed zone after the main reduction of manganese oxide is finished. Probably the ?pick up? of Si in the metal is quite fast and takes place as the metal trickles down through the cokebed towards the metal bath. The distribution of Si between SiMn alloys and multicomponent MnO-SiO2-CaO-Al2O3-MgO slags is mainly determined by the process temperature, the silica content of the slag and its R-ratio = (CaO+MgO)/Al2O3. As an example, the equilibrium content of Si in the alloy will increase by about 6 % if the R-ratio is reduced from 2 to 1, provided constant temperature and silica content. The effect of temperature is also considerable. The equilibrium content of silicon will increase by approximately 6 % per 50°C in the temperature range 1550°C to 1700°C. The equilibrium content of MnO in SiMn slags depends first of all on the temperature and secondly on the silica content of the slag. At 1600°C the MnO content decreases from about 9 % at silica saturation to a minimum of about 3-4% when the silica content is reduced to about 40-45%.

Jan 1, 2004

By Deshmukh A. M.

Existence of human beings and their relationship with the nature is symbiotic. The lack of perspective and negligence of nature disturbs the equilibrium of environment and causes unprecedented disasters. Geotechnical engineers are directly concerned with hazards of nature as elements of foundation and of nature are inter related. Rational design and construction of foundation can be accomplished only after properly assessing influence of environment This paper briefly delineates impacts of environment and human activities and presents salient features of management of impacts through the system of deep foundation. Limitation of negative effects and enhancement of positive developments necessitates eco-consistent planning of engineering projects based on the geotechnical aspects of environmental impact management.

Jan 1, 1996

By David L. Shearer

INTRODUCTON James Howden first secured an order for two Service Tunnel Boring machines in November 1986. These Tunnel Boring machines were 5.7 and 5.4 metres in diameter and the full length including back up was 215 metres. Manufacture commenced in December 1986 at the Glasgow factories of James Howden & Company with the deliveries to site of the machines in September 1987 and March 1988 respectively. In December 1987 two further orders were secured for the land running tunnels at 8.7 metres diameter. This paper presents some of the challenges in building tunnel boring machines for the Eurotunnel project between Britain and France. The general specifications of the Tunnel Boring machines and length of drives are shown in Appendix 1. DESIGN PARAMETERS The specification given by the Consortium TML on behalf of their client Eurotunnel cleary indicated that cutting of the face should be concurrent with the building of the precast concrete lining rings. In order to do this a telescopic machine was thought to be the best solution. Ground conditions were described as chalk marls of homogeneous nature with the possibility of friable areas and some revelling. A shielded type TBM with open cutter head was chosen together with a telescopic section and a rear

Jan 1, 1989

Spectroelectrochemical Investigation of Hydroxamate Reagents on Copper Oxide Minerals

Sep 13, 2010

By M. H. Weinecke, B. P. Faulkner

This paper will discuss the process for making lightweight aggregate, the waste materials that make good lightweight aggregate, the chemistry of making lightweight aggregate and finally a discussion of the commercial prospects for making lightweight aggregate from wastes. Svedala Industries has been making lightweight aggregate (LWA) from waste materials for the last ten years. Many clay-like materials, such as coal-fired boiler ash and washings from a granite quarry, can be used alone or with additional waste materials to produce a commercially saleable LWA.

Jan 1, 2001

By Georgene Renner

At the beginning of the 1990s, Communism fell and signaled the end of the Cold War. The world rejoiced but also watched and waited to see how those countries would restructure themselves. The 1990 SME Annual Meeting was held at the Salt Palace Center in Salt Lake City, UT. The keynote session featured Alistair Frame, chairman of RTZ; Paul Queneau, professor of metallurgy at the University of Utah; and TS Ary, director of the U.S. Bureau of Mines. The SME Board of Directors voted to hire a Manager of Public Information and Education to be the GEM Program coordinator. This person was to collect and disseminate information that could be used by individual members and Local Sections to interface with government personnel and the general public.

Jan 1, 2007

By Libby R. Ricafort, Victorio V. Pato, R. S. Pizarro

Introduction Atlas Consolidated Mining and Development Corp. (ACMDC) started gold production at its Masbate gold mine early in 1980. This involved an open-pit mine and a 3.5-k/d (3850-stpd) carbon-in-pulp processing facility (Pizzaro and Antonio, 1981). When this operation started, the mine began stockpiling sub-grade milling material averaging 1 g/t (0.029 oz per st) gold. Furthermore, geologists estimated that there were additional low grade reserves within the ultimate pit limits. These amounted to 2.4 Mt (2.6 million st) with an average grade of 1.1 g/t (0.03 oz per st) gold. The success of low cost heap leaching prompted an investigation to determine if this tech¬nique would be applicable for the low grade Masbate ore. The findings were favorable and a series of laboratory tests were undertaken. These tests indicated the amenability of this subgrade milling ore to heap leaching. Depending on ore size, gold extractions of more than 60% were obtained. To further define operating parameters for a commercial heap leaching plant, a 400-t (440-st) batch pilot plant was built and operated. These test results were used to design the first commercial heap leaching plant in the Philippines. One design concern was the control of solutions during the rainy season. Due to the material's low grade, every effort was made to minimize capital and operating costs. To this end, surplus mining equipment from the copper operations of ACMDC and used machinery in the crushing circuit were considered. Location: The Masbate gold heap leaching operations are located on the northeastern part of Masbate Island, Philippines. This is about 480 km (300 miles) south-east of Manila. Climate: The climate is moderate with two distinct periods. The dry season runs from January through June, and the rainy season extends from July through December. During the wet season, the rainfall at the mine site averages 300 mm/m (11.8 in. per month) for a total of about 2000 mm/year (78 in. per year). However, heavy downpours in excess of 100 mm/h (4 in. per hour) can occur. Geology: Four distinct rock types have been identified in the pit area. They are tuffaceous agglomerates, andesitic agglomerates, metasedimentary rocks, and hornblende augite andesitic porphyry. The tuffaceous agglomerate occupies the northern and western flanks of the mine. Andesitic agglomerates are localized distinctly in the central portion of the volcanic plug within the mine site. The eastern boundary of the mine is occupied by metasedimentary rocks, whereas, the hornblende augite andesitic porphyry occurs as an intrusive within the andesitic agglomerate and tuffaceous agglomerate. Some areas of the pit contain high proportions of clay minerals, requiring an agglomeration step in the flowsheet. This ensures satisfactory percolation through the heaps. Ore characteristics: Gold and silver are microscopically dis-

Jan 9, 1987

Recovery of Rhenium from Mineral Raw Materials of Kazakhstan

Sep 13, 2010

By Henri F. Letient

At the 25th Annual B.C. Mine Reclamation Symposium in September 2001, Huckleberry Mines Limited received the Jake MacDonald Reclamation Award for its exemplary mine waste management plan, conceived to prevent the onset of acid mine drainage and facilitate reclamation of the site. The mine is an excellent example of a total mine waste management plan, with all materials scheduled in detail for the life of the mine. The filling plan for the waste management facility takes into consideration the requirement for permanently flooding the potentially acid generating rock. From an acid generation point of view, the tailings fall in the zone of potentially acid generating material. To avoid long-term ARD concerns, it is planned to float pyrite out of the tailings towards the end of the mine life, thereby generating a non-acid generating tailings stream which will be used to cap the deposited mine waste. The pyrite-rich tailings will be discharged into the deeper portion of the impoundment. On closure, a permanent water cover will be maintained over the mine waste. Only beaches of non-acid generating tailings will remain exposed. Mining will be phased to also allow one of the pits to provide storage for potentially acid generating rock and to be flooded at the end of mine life.

May 1, 2002

By Alan Dahlstrand

The Jamestown Mine is a 6.3-kt/d (7000-stpd) open-pit gold mining operation located in the central portion of California's historic Mother Lode district. Most early production from the Jamestown area occurred in underground operations from 1906 through 1916. Pit production began at Jamestown in early 1987 and continued until July 1994. Although additional mineral resources existed, they were deemed to be uneconomic. About 23.3 t (750,000 oz) of gold were produced from pit operations, compared to 31 t (100,000 oz) from early underground mining. Recent operations at Jamestown included two open pits, a flotation mill and a flotation tailings facility. Flotation concentrates were produced in Jamestown and shipped to Yerington, NV for cyanide leaching in a carbon-in-pulp (CIP) circuit.

Jan 1, 1995

By Erin N. Legault-Seguin

The Lac des Iles Mine (LDI) is located approximately 100 km northwest of Thunder Bay, ON. The mine has been in operation since 1993. The initial mine production was 2,300 mtpd and increased to 15,000 mtpd following a mine expansion project that was completed in 2001. Effective Oct. 29, 2008, LDI was shut-down under care and maintenance due to low metal prices. Prior to shutting down, LDI was the only primary PGM deposit in operation in Canada and of the few found globally. The complex geology and physical properties of the deposit causes several challenges for the concentrator. This paper will discuss the solutions to the main challenges of attaining nameplate tonnage and achieve satisfactory Pd recovery and concentrate grades.

May 1, 2009

Precast prestressed concrete piles designed to be end-bearing in a sand stratum at Drax Power Station met with extremely variable resistance during driving. Some piles came to virtual refusal almost immediately on entering the sand whereas others were driven to considerable penetration with very low resistance. Redriving and load tests on piles experiencing low resistance on initial drive showed that take up in strength occurred over a relatively short period of time. Investigations involving the use of pneumatic piezometers revealed the development of significant excess pore pressures during driving. Samples from boreholes showed that piles met the least resistance when the sand had a high silt content. Comparison with the original site investigation data demonstrated the difficulties in predicting detailed pile behaviour. The varied behaviour could not be related to the original borehole logs or to SPT or static cone penetrometer results. The factors controlling pile driving behaviour were essentially geological and could only be explained with reference to local soil grading.

Jan 1, 1989

By Poi G, Madgwick J. C, Davis P, Pannowitz D, Cho D, MacKay B, Chan S. M, Varga R. A, Chun U

Periodic dilute sulphuric acid treatment ofstill, batch-fed, molassesenriched, microaerobic, manganese-dioxide-Ieaching microbial cultures led to marked improvements over untreated cultures. Percentage Mn++ recoveries increased (7X), rate of Mn++ formation improved (3X) and yields of Mn++ per molasses use were more economical (5 X). The yield in terms of molasses used improved with decreasing sugar used (eg 1.17 g Mn++/gram molasses at 0.2 per cent molasses (w/v) feed and 24 per cent (w/v) pulp density MnO2 tailings). The most effective Mn++ leaching in terms ofpercentage recovery (97 per cent) and rate ofleaching (46 mg Mn++/day) was at 0.5 per cent molasses (w/v) and 14 per cent pulp density (w/v) MnO2 tailings.

Jan 1, 1986

By M. E. Poad, M. M. McDonald, J. C. Johnson, W. G. Pariseau

A U.S. Bureau of Mines case study of pillar recovery in high-grade ore near the Ross shaft at the Homestake Mine, Lead, SD, has demonstrated the usefulness of the finite-element method for evaluating shaft pillar mining plans and shaft stability. This report focuses on mine measurements and calibration of the two-dimensional computer model and is the second in a series of three Reports of Investigations describing the Ross shaft study. In this study, borehole extensometers and other instruments were installed to provide data for model verification and to monitor the shaft. Results of the recalibrated two-dimensional model (UTAH2) confirmed the premining stability evaluation. However, after mining began, concern was expressed because cracks and other signs of ground motion appeared at considerable distances from the area of active pillar mining. In part 3 of the study, an intense three-dimensional modeling effort using UTAH3 was initiated. The results again showed that the observed effects were within expectations and that the shaft would remain safe. Three-dimensional analyses of alternative pillar mining scenarios indicated that more of the shaft pillar ore reserve could be recovered than previously thought.

Jan 1, 1995

By Bruno Bussière, Guosheng Zhan, Michel Aubertin, Vincent Martin, Robert P. Chapuis

The study evaluates the hydrological behaviour of exposed and covered waste rock dumps. The objectives were to determine the major factors influencing unsaturated flow in waste rock dumps and covers, and to improve the in-situ, laboratory and numerical modeling characterization methods. Using material properties obtained from in-situ and laboratory tests, waste rock dumps of different configurations, with and without covers, were modeled. It was found that a properly designed “Store, divert and release” (SDR) cover allows most of the water to be diverted downslope and discharged outside of the waste rock dumps. The SDR cover seems to work efficiently even in extreme storm events. The numerical modeling results show that the unsaturated hydraulic properties (e.g. air entry value and water entry value) of the materials largely control the infiltration of water into waste rock dumps.

Jan 1, 2005