Search Documents

By D. R. Dolinar

The fall of small pieces of rock between roof bolts causes over 80 pct of the ground fall injuries in underground coal mines. Roof screen, if installed on the bolting cycle, can significantly reduce the number of these injuries. As the surface of the roof fails, the screen will have to retain the broken rock without failing or excessive deformation. Welded wire screen is the most common type of screen material used for roof surface control in underground coal mines. The load-deformation characteristics and the load capacity of welded wire screen were evaluated in the laboratory in a specially built test frame. In the frame, the square screen sections were held in place by bolts and bearing plates at the four corners while a center load was applied to the screen. The parameters evaluated included the wire gauge and configuration, the bearing plate loads and bolt spacing. The wire gauge of the tested screen was 4, 6, 8, 9 and 10. Maximum screen capacities for both load and displacement were developed for each of the wire gauge sizes along with the screen stiffness. This information can be used for screen selection and for the evaluation and determination of screen performance. DISCLAIMER: The findings and conclusions in this report have not been formally disseminated by the National Institute for Occupational Safety and Health and should not be construed to represent any agency determination or policy.

Jan 1, 2009

By Linda Duncan, Trevor Yeomans, Chris Potorieko, Michael Fullam

"NVI Mining’s Myra Falls Operation is a 4,000 mtpd copper/zinc flotation circuit with by product gold of ~28,000 ounces per year. Gold recovery has historically averaged 40-55%, however, a portion of this was recovered in the zinc concentrate and received poor payment. Two Knelson CD-30 Concentrators have been operating in the grinding circuit since 1992, with gravity recovery averaging about 2-5% over that time period.The Myra Falls gravity circuit was one of the very first hard rock mining installations operating in the world with automated Knelsons. The mine has employed a unique and unusual upgrading method for the Knelson concentrate that had never been evaluated as to its efficiency. Recent Gravity Recoverable Gold Testing by McGill University, and mathematical modelling of the Gravity Circuit by Knelson Gravity Solutions indicated the gravity circuit was not living up to its potential. Myra Falls Personnel changed the upgrade system-operating regime, and a complete gravity audit of the grinding circuit was carried out, with the results confirming the initial suspicions. Gravity recovery increased from 5% to 15%, with overall gold recovery improving by 5%.INTRODUCTIONNVI Mining operates a 4000 tpd mine and mill complex on Vancouver Island. The milling circuit consists of open circuit rod milling, closed circuit ball milling, gravity recovery, copper flotation, zinc flotation, and tails disposal. There are two milling circuits, “A” circuit, and “B” circuit."

Jan 1, 2006

By Pengfu Tan

The control of converter slag chemistry and slag viscosity has played an important role in optimizing converter operations. A thermodynamic model of copper P-S converter and a viscosity model of converter slag have been used to predict the chemistry and viscosity of converter slag. The effect of oxygen potential, SiO2/Fe in slag, detection of slag blow endpoint, and temperature on slag viscosity, liquidus temperature of converter slag and skimming operation has been discussed. Some applications of the industrial operations have been presented.

Jan 1, 2006

By R. E. Old

Through the use of pressure and production records, formation properties and bottom-hole sample data, the performance of an oil reservoir may be studied analytically to define and evaluate the natural forces acting on and within the reservoir. Use is made of material-halance methods and the equations for natural water encroachment. to estimate reserves. Methods for calculation of pressures are given. A study of the Jones sand, Schuler field, Arkansas, has been made and is given here to illustrate the value of the methods discussed. Introduction With the decreasing rate of discovery of new oil reserves, attention is necessarily focused on the efficient development, evaluation, and production of existing reserves. From the nation's viewpoint, the necessity of conserving resources is obvious. From the operator's viewpoint, the problem is to lengthen the period of profitable operation, in an attempt to increase the return on his investment. To do this the operator must take advantage of the natural forces acting on and within the reservoir. Natural water encroachment, the nemesis of profitable operation in the past, can be and is being harnessed to produce a greater oil recovery during the stage of flowing production. Proper evaluation of water encroachment rates and a fuller under- standing of reservoir behavior dictate the appropriate production procedures. Complacency in hit and miss production is obsolete. Oil production must and will approach the efficiency of other businesses, such as manufacturing. A manufacturer will not place an article on the market until he has fully investigated the processes involved, additional investment in equipment, costs of production, and expected profits. These may be modified by actual experience at a later date, but at least he begins with an idea of expected return. It is just as logical that an oil operator should investigate these same factors during the development and the early period of production of an oil reserve. The complexity of the problems existing in oil reservoirs should not be underestimated. Conversely, they should not be regarded as insoluble. Many completely defy solution, but there are others that can be solved completely or attacked intelligently to yield approximate results. The petroleum engineer has many tools, both figuratively and literally, at his disposal. Physical data such as core analyses, electrical logs, bottom-hole sample analyses, and bottom-hole pressures are accumulated extensively. Advances in the analytics of fluid flow have kept pace with the advances in measurement of physical data. It is the purpose of this paper to show how some of these records may be analyzed to define certain phases of reservoir behavior.

Jan 1, 1943

By Ken Cross

This paper aims to demonstrate that explosives organizations and workers have a legal, moral and financial duty to be able to demonstrate their competence when required, and how that may be achieved at any level from explosives storekeeper to senior explosives engineer on a major project. The concept of competence is outlined, as are the benefits to members of staff, management and the organization, particularly in a regulatory regime that includes competence management as a key performance indicator.

Jan 1, 2013

By Michael Feroz, Marcus Jensen, James E. Lindell

The Southern Nevada Water Authority (SNWA) operates two water-intakes in Lake Mead, located 20 miles east of Las Vegas, Nevada. Severe drought has caused decline in lake level by 85 feet since 2000 and future declines are expected. SNWA will construct a third deep-water intake to ensure existing water system capacity. This paper describes expected construction challenges for the new project that consists of: an intake structure and tunnel beneath the lake, pumping station, pipeline to connect existing treatment facility, and interconnecting underground adits. The project will be completed in the year 2012 for total estimated cost of approximately $600 million.

Jan 1, 2007

By Gerald M. Ellis

ntroduction As the gold mining industry continues to develop in the Dominican Republic and Haiti, more deposits will undoubtedly be discovered that will be amenable to development. The Pueblo Viejo gold mine is currently in operation in the Dominican Republic. It has become an important component of that country's economy. Pueblo Viejo output is important to the government as a foreign currency earner. It is also said to be among the world's more successful gold mines. But, while Pueblo Viejo is successful, no other major gold discoveries have been made in recent years. Therefore, alluvial deposits of gold have caught the attention of geologists on the Island of Hispaniola. In the past four years, exploration and investigation of alluvial deposits have been initiated in both the Dominican Republic and Haiti. This type of activity is expected to continue over the next few years. Alluvial gold mining is rudimentary gold washing, done mostly by farmers. It is an old tradition, dating back at least 100 years, and is done by small, independent, or community farming villages in the mountains and plains of the Dominican Republic. Investigations in the DR Recently, alluvial gold investigations have been undertaken in well known locations of the Dominican Republic. One is in the Villa Altagracia area. Here, the terraces and gravels of the Haina River basin were examined, test-pitted, and assayed by Minera Altagracia, a local Dominican mining group. Results led to a new investigation by the state-owned Rosario Dominicana (RD), the company that mines the gold at Pueblo Viejo. Rosario tested areas previously investigated by Minera Altagracia. RD could not define the type of concentration that could justify an industrial-scale type of exploitation. The Haina River placers are located in the flats and valleys of Central Dominican Republic. They are classified as small-scale type of operations where local cooperatives can do the traditional gold washing. It is not now considered a dredgable project for a mining company. The next alluvial gold investigation was undertaken by the Dominican Department of Mines and others in an area of some 700 km2 (270 sq miles) in the northeast near Miches. Farmers have been washing gold in streams and excavating pits in various areas, particularly La Mina and have made a living. Government geologists panned several hundred streams and river tributaries. They also washed material from deep excavations. The results, however, were negative insofar as locating alluvial gold concentrations suitable for large-scale or industrial-scale exploitation. The most favorable locations were the terraces along the Jayán and Cuarón Rivers in the area of Miches. But the grade od concentration is poor. Actually, only traces of gold were found in these

Jan 8, 1986

By Jaidev Sankar

The dream of constructing the new Second Avenue Subway in New York has finally become reality as the first construction contract package is currently underway. This first contract requires the construction a TBM Launch Box in the middle of Second Avenue from which a Tunnel Boring Machine (TBM) will bore two tunnels south to 63rd Street. This paper will discuss the design of this contract and how construction has progressed including preparation, site constraints, utility construction and com-munity impacts while highlighting the challenges of working in an urban environment. It will also discuss moving forward on this major project outlining the remaining contract packages including their scope and status.

The purpose of this study was to investigate the immobilization as a host for metallic pollutants (Cr, Cu, Pb, and Zn) by ettringite phase. Ettringite phase is produced through hydration reaction of calcium aluminate with gypsum. From the XRD patterns, it is known that the distance between spaces in 010 planes in ettringite crystal increase with an increase of ionic radius of heavy metal except Pb; no big difference is shown. For this reason, the d-value of 010 planes in ettringite crystal increased with the substitution of Cr, Cu and Zn having a big Al ironic radius. But in case of Pb, because the substitution occurred at calcium site, it does not influence to increase d-value of 010 planes.

Jan 1, 2006

By Peter Grundy

La eficiencia de los recursos en los procesos transparentes de gestión de las empresas permite aumentar el valor de los accionistas. En ese sentido, el presente texto señala el uso de la RCM como estrategia en el funcionamiento de un equipo que se centra en la confiabilidad. RCM es un proceso lógico que involucra aspectos técnicos y de negocio, capaz de producir resultados a muy corto plazo. Este proceso concluye con una recopilación de documentos fiables y totalmente óptimos para el desarrollo de las funciones de mantenimiento. Su uso correcto en la evaluación de los requisitos de mantenimiento de los equipos existentes, genera un mantenimiento menos costoso, confiable y eficaz. Asimismo se disminuye los costos de mantenimiento y se relaciona los aspectos ambientales y de seguridad.

Jul 17, 2000

By Sotiris Psomas, Colin M. Eddie

"Steel Fibre Reinforced Concrete (SFRC) Segmental Tunnel Linings have successfully been used for over 20 years in the UK and have been adopted in a number of high profile projects such as High Speed 1, Crossrail, Thames Tideway, as well as High Speed 2. Tunnel linings and especially SFRC design are not covered in the Eurocodes. This shortage of SFRC tunnel design rules seems to be partially addressed by several international publications. However, in the UK, the ‘design-assisted by testing’ (DAT) approach has also been adopted. The Paper discusses the UK’s best design practice and focuses on the DAT methodology as applied in the case of the 6.9km (4.3miles), 7.8m (25.6 feet) ID Lining for the £635million Lee Tunnel Project. The design approach, the full scale testing at the Building Research Establishment (BRE), and the construction innovations are presented. This experience will be transferred to the £4billion Thames Tideway Tunnel.INTRODUCTIONSteel Fibre Reinforced Concrete (SFRC) has been used for Tunnel segments for more than 20 years. The first application of SFRC in the UK was for the Heathrow Baggage tunnel (1994). Since then significant size tunnels have been designed and constructed, such as the Jubilee Line (1999) High Speed 1 (CTRL, 2006), Crossrail (2014), Lee Tunnel (2014) and the scheduled 25km Thames Tideway (‘Super Sewer’) and High Speed 2 rail tunnels. However one the main obstacles in achieving streamlined design and improving efficiency are the lack of appropriate design guidelines for SFRC tunnel segments. This issue will – to some extent – be addressed by a number of current documents on tunnel FRC design either being produced by BSi (PAS8810, expected 2016), ACI (544.R) and ITAtech (Design Guideline PCFRC, 2015) in an effort to advance the design of SFRC and take into consideration the recent developments in Steel and Macro-Synthetic FRC technology."

Jan 1, 2016

By Richard E. Ray, George N. Aul, Fred Garcia, William P. Diamond

Increasing longwall panel dimensions, particularly face width in gassy coalbeds, may result in unexpected increases in methane emissions. To investigate this problem, continuous longwall face emission monitoring studies were conducted at two adjacent mines operating in the Pocahontas No. 3 Coalbed, where longwall faces were to be extended from 229 to 305 m (750 to 1,000 ft). It was predicted by regression analysis of methane emissions data from 229 m (750 ft) wide longwall faces that extending faces to 305 m (1,000 ft) would increase methane emission rates by only 7 percent (0.6 m3/min (20 cfm)), to 8.6 m3/min (304 cfm) at the VP-1 Mine. In contrast, it was predicted that extending faces at the VP-3 Mine could increase methane emissions by as much as 13 percent (1.8 m3/min (65 cfm)) to 16.1 m3/min (567 cfm). The geologic and mine design factors influencing the variation in face emissions between the two mines will be discussed.

By B. Galy, L. Giraud

"This paper compares Canadian provincial mining safety regulations regarding the use and testing of cage safety catches, including a brief history and evolution. Regulations are similar across provinces, with only slight variations. Currently, the “Ontario-type” safety dog is the most commonly used safety catch in Canada. Performance estimation of the compensation mechanism for different safety-dog shapes and tooth angles show this shape works well and has consistent braking results, but the best efficiency is obtained for initial tooth angles greater than 10°. Miner safety is questionable for lightly loaded cages, an issue that should be addressed technically and legislatively.RÉSUMÉ Le présent article compare les diverses réglementations de sécurité minière concernant les parachutes des cages dans les provinces canadiennes ainsi que les essais qu’ils doivent subir. Il semble que les réglementations soient semblables à travers les provinces avec quelques légères différences ou divergences. Un bref historique des parachutes et de leur évolution est présenté. De nos jours, le parachute de « type Ontario » est le plus fréquemment employé à travers le Canada et il présente des résultats de freinage uniformes. Une estimation de la performance du mécanisme de compensation pour les diverses formes de taquets de sécurité et les divers angles des dents montre que cette géométrie fonctionne bien; cependant, la meilleure efficacité est obtenue pour des angles de dents supérieurs à 10°. La sécurité des mineurs est mise en jeu pour des cages faiblement chargées et ce point devrait être traité du point de vue technique et du point de vue législatif."

Jan 1, 2016

By J L. Mauk

Low sulfidation epithermal deposits are important sources of gold and silver, and are considered the extinct analogues of modern geothermal systems. The aerial extents of alteration halos that surround twenty-two epithermal deposits range from 4 to 315 km2, with many less than 60 km2. Deposits with alteration halos <30 km2 typically have well defined limits, whereas deposits with alteration exceeding 30 km2 are commonly complicated by overlapping alteration centres related to adjacent epithermal deposits or other deposit types (i.e. high sulfidation, porphyry). Irrespective of the physical coverage of vein or alteration halos, both large (>60 km2) and small (<20 km2) deposits can contain large amounts of gold and silver. The size ranges for twenty-one analogous liquid-dominated geothermal fields from around the world have a restricted size range of 5 to 60 km2 and irrespective of physical size, commonly have multiple zones of focused fluid upflow. From an exploration perspective the comparison between epithermal deposits and geothermal fields provide the following four important points. 1) Alteration halos surrounding epithermal deposits as well as those for analogous geothermal systems show a range of sizes, although most are less than 60 km2. Therefore, where alteration exceeds 60 km2 multiple vein systems related to several paleogeothermal systems are predicted. 2) Multiple upflow zones are common in geothermal fields of all sizes (5 to 60 km2) and although difficult to demonstrate in epithermal deposits there is a strong possibility of discovering several discrete adjacent mineralised centres. 3) The orientation of veins parallels the principle orientation of the surrounding alteration and where alteration is wider than the vein strike length, this could suggest the occurrence of adjacent veins. 4) The physical size of both veins and alteration zones is not important in relation to amount of contained gold, as both large and small can contain large amounts of gold. These conclusions provide insight into the physical size limits and hydrologic structure of these paleogeothermal systems and highlight the potential for multiple mineralisation centres within a single alteration halo.

Jan 1, 2004

By Glenn Kosick, Roger Amelunxen, Glenn Dobby

"The variability in flotation response within an orebody is often a significant problem to address during the design phase of a flotation circuit. In addition, for existing operating plants, the reasons for such a variability need to be clearly understood and accounted for if plant performance is to be optimized. MinnovEX Technologies, in collaboration with major mining companies, is developing methodologies and tools to address the issue of variability in ore characteristics (such as ore hardness and flotation response). The tool is used for design and scale-up of flotation circuits from lab flotation data, and for prediction of recovery and final concentrate grades throughout the mine block model for any given circuit design.INTRODUCTIOTNH: EI SSUEB EINGA DDRESSEDThis paper describes the current development of a methodology and software tool for improved flotation plant design and enhanced prediction of froth flotation performance in an operating plant. The need for this tool is attributed to two primary factors: variability of flotation response properties throughout an orebody and related difficulties with scaleup from laboratory tests. Consider these in more detail.It is well recognized that separation performance via froth flotation will vary significantly within a single mineral deposit. This has been enhanced through the wide application of SAG milling. Throughput with SAG mills is more susceptible to ore hardness changes than is the case with crushing-rod-ball circuits; it is not uncommon to see SAG mill throughput to vary by up to 100% on a regular basis, e.g. 1000 tph to 2000 tph.The implication of this on laboratory testing for prediction of metallurgical performance is as follows: it is unlikely that either the plant grind (size distribution) feeding froth flotation or the flotation residence time will be known at the time of laboratory testing for a given block of ore. Hence, the grind used for the laboratory test is not likely to be that which actually occurs once the ore is processed, and the laboratory retention time may not represent the plant conditions."

Jan 1, 2002

The Bureau of Mines human factors research program is directed toward reducing accidents and improving the overall efficiency of the person-machine environment interface found in surface and underground mines. The focus of the hum factors program therefore, is to insure that sound knowledge is available concerning human capabilities and limitations, and that this knowledge is applied to the design, of mining equipment, work tasks, and management procedures. The papers presented in these proceedings summarize some of the recent Bureau research in hum factors. The papers focus on two broad areas, human resource issues and human engineering of equipment, tools, and work procedures found in mines.

Jan 1, 1987

By Ronald M. Hays

The Duluth Gabbro Complex in Northeastern Minnesota possibly contains a significant domestic copper resource and the nation's largest nickel resource. Exploration has discovered large low-grade copper-nickel (Cu-Ni) deposits between Hoyt Lakes and the Boundary Waters Canoe Area (BWCA). The mining and processing of Cu-Ni will have environmental, economic, and social impacts. The purpose of this study is to relate major environmental, economic, and social considerations to various aspects of Cu-Ni extraction. An open pit and two underground (block caving and open stoping with backfilling) models were developed to generate information on the impact of Cu-Ni extraction. Important considerations having environmental, economic, and social impacts (luring various aspects of Cu-Ni extraction are identified and defined. These aspects are exploration, development, mining, beneficiating, smelting, transportation, and termination of operations. Considerations are grouped into the general categories of site, industrial, energy, climatic, resource, water, air emission, waste disposal, employee, tax and royalty, transportation, and community considerations. Cu-Ni extraction in Northeastern Minnesota presents major environmental, economic, and social risks. Decisions are required on trade-offs between adverse and beneficial impacts. The approach used in this study assists in assessing environmental, economic, and social impacts. It will aid in the examination of potential and projected short-term and long-term advantages and disadvantages and will aid in the development of Minnesota's Cu-Ni resource for the maximum benefit to society.

Jan 1, 1974

By Reed M. E, Cloutt B

Particulate samples were taken from the gas space in the settler of the Kalgoorlie nickel smelter using a vertical sampling probe and a specially designed isokinetic sampling probe which also quenched the samples. The vertical sampler was found to give unrepresentative samples. Suction thermocouple measurements of the gas temperature were also made. Using the isokinetic probe samples were taken at four points ranging from near the base of the reaction shaft to the base of the uptake at depths up to 1.5 m into the settler. Dust loadings and the sizing of the samples were determined. These parameters were found to be most affected by sample position and depth. The dust loading decreased along the settler but increased with depth. The loadings varied from zero near the roof to several hundred g Nm 3 near the slag. The dust also became coarser with increasing depth into the settler. Examination of the samples showed them to consist of spherical particles the largest of which were about 500 microns in diameter. The dust was mainly composed of mixed iron/nickel oxides with a little sulphide.

Jan 1, 1991

By R. Strydom, J. H. Selby

Published information is available on the radiological impacts of disposing of zircon sand in a landfill. Zircon flour by virtue of its finer particle size presents a different set of issues during disposal. This paper describes two options for disposal of such fine grained materials – namely incorporation into concrete aggregates and agglomeration by addition of cement. The study considers the radiological exposure of the public from such disposal methods and concludes that these options are viable alternatives for the safe disposal of waste zircon flour. The disposal of zircon into concrete aggregates at a rate of 10 per cent produces a sufficiently low effect to allow such aggregates to be used in building foundations or other such mass concrete applications. The use of cement agglomeration methods will also provide a safe method of landfill disposal provided at least 20 cm of soil cover is included.

Jan 1, 2003

By D. Eugene Rannels, Sarah E. Dunsmore, Cara Martinez-Williams, Yu-Chen Lee

"Dunsmore, Sarah E., Yu-Chen Lee, Cara Martinez Williams, and D. Eugene Rannels. Synthesis of fibronectin and laminin by type II pulmonary epithelial cells. Am. J. Physiol. 270 (Lung Cell. Mol. Physiol. 14): L215-L223, 1996.Previous investigations demonstrated that type II pulmonary epithelial cells regulate extracellular matrix deposition as a function of time in primary culture. In those studies, the matrix fraction was analyzed as a whole. The present work focused on two components of the type II cell matrix, fibronectin and laminin. These glycoproteins have differing effects on differentiation of type II cells in primary culture. Fibronectin synthesis was quantitated between day 1 and day 6 in the cells, matrix, and medium; laminin synthesis was quantitated only in the cells. Although total fibronectin synthesis was regulated as a function of time in culture, reaching its greatest value on day 2, the average proportion of newly synthesized fibronectin in the cells (35%), medium (50%), and matrix (15%) remained constant over a 6-day interval. Between day 2 and day 6, the relative abundance of fibronectin messenger RNA increased 6.5-fold. Rates of cellular laminin synthesis did not vary with time in culture. These results support a role for differential regulation of fibronectin and laminin synthesis to determine the composition of the type II cell extracellular matrix. INTERACTIONS BETWEEN THE pulmonary epithelium and alveolar basement membrane may play a role in the physiology and pathophysiology of the lung. Pulmonary epithelial cells and the alveolar basement membrane form one component of the blood-gas diffusion barrier. Integrity of this barrier is crucial to normal lung function. Specific domains of alveolar basement membrane components have been proposed to determine localization of type I and type II pulmonary epithelial cells during lung growth and development, as well as during repair of the alveolar surface after injury (13). In the injured lung, the extent of damage to the epithelium and the underlying basement membrane is thought to be a key factor to determine subsequent repair or fibrotic scarring (3)."

Jan 1, 1998