Search Documents

Bioremediation of Acid Mine Water Using Fly Ash and Desulfotomaculum nigrificans One of the major concerns for the mining industry especially after the mine closure is the generation of acid mine drainage (AMD), and its discharge into the environment surrounding the abandoned mines, leading to serious environmental pollution. AMD is usually characterized by high concentration of dissolved metal ions, sulfate and low pH. The efficacy of fly ash was assessed for the removal of metal ions such as iron, zinc and copper as well as sulfate from synthetic acid mine water. Complete removal of ferric and ferrous, 80 per cent of Zn, 83 per cent of Cu and 62 per cent sulfate removal could be achieved, with a concomitant increase in the pH value from 2.3 to 7 using fly ash as an adsorbent under appropriate conditions. The free energy of adsorption of the metal ions onto fly ash was found to be negative, while the adsorption process was endothermic and adhered to the Lagergren pseudo-first order rate equation. Bioremediation studies using a typical sulfate reducing bacterium namely Desulfotomaculum nigrificans, after pre-treatment of the synthetic acid mine water with fly ash, cumulatively resulted in about 94 per cent zinc, 100 per cent copper and 90 per cent sulfate removal. The possible mechanisms of metal ion removal and sulfate reduction from acid mine water utilising Desulfotomaculum nigrificans are discussed.

Sep 13, 2010

By G R. Hancock, S Grant, T Whiteside, J B. C Lowry, J Boyden, T J. Coulthard

Physically-based landform evolution models (LEM) provide a spatial framework to forecast the long-term geomorphic stability of post-mining landscapes. When used to test the relative stability of different landform designs, LEMs may assist with the development of optimal closure designs for rehabilitated mines. However, in order to reduce prediction error, factors controlling landscape evolution must also be accurately represented by models. This requires that the correct sets of processes are represented and that driving parameters used in LEMs are, if necessary, calibrated to the landscape of interest.Vegetation exerts strong controls on the hydrologic and geomorphic processes that drive landscape evolution. Hence, the spatial and temporal scales over which typical patterns in vegetation are represented in different landscapes are important considerations in LEM calibration. However, vegetation is rarely accounted for in LEMs and even when integrated is often represented simply, without representing spatial dynamics of vegetation cover that may impact landform development.This study focuses on characterising vegetation patterns to calibrate a new vegetation module of the The Cellular Automaton Evolutionary Slope and River (CAESAR)-Lisflood LEM to be applied to a conceptual rehabilitated landform of the Ranger uranium mine located in the Alligator Rivers Region (ARR) of northern Australia. In the ARR the spatial dynamics of vegetation over time are largely driven by monsoonal rains and topography. Extensive dry season fires are also common in the region, temporarily reducing vegetation cover where they occur. Hence, hydrology, topography and fire disturbance interact to shape a distinct, yet dynamic, mosaic of different vegetation types of varying cover density. As a basis for calibrating the new vegetation function, the distribution and dynamics of vegetation are characterised for this savannah landscape by remote sensing, in conjunction with ground data.CITATION:Boyden, J, Lowry, J, Coulthard, T, Whiteside, T, Hancock, G and Grant, S, 2016. Accounting for vegetation dynamics in landform evolution modelling, in Proceedings Life-of-Mine 2016 Conference , pp 63–66 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jun 28, 2016

By Joaquim Luiz Monteiro Barros

Este trabalho tem como objetivo principal apresentar de forma didática e com um exemplo prático a viabilidade da aplicação da tecnologia de recuperação de calor no sinter cooler, com a finalidade de gerar energia térmica (ar quente, vapor, água quente, etc) reduzindo o consumo final de combustíveis na planta.

Aug 17, 2017

By A Liu, T Ren

Gas explosion in underground coal workings can pose a serious threat to the safety of mine workers and the entire mine operations. Gas explosion is a very complex thermal-chain reaction in a confined underground environment. Based on combustion and explosion theory, three dimensional (3D) computational models were developed to simulate mine gas explosion flame and overpressure wave propagation in a single entry gateroad in underground coalmines. Six different explosion scenarios were modelled and compared with large scale experimental results and AutoReaGas simulations. Model validations show that the use of shear-stress transport (SST) k-? model together with eddy-dissipation model (EDM) produces good agreement with both experimental and AutoReagas simulation results. Modelling results demonstrated that the changes of temperature versus time can be divided into four stages, ie the initial condition stage, and periods of warm-up, active burning, and burnt-out. Assuming a limited volume of methane is involved in the explosion, the maximum temperature decreases as the distance increases from the explosion point, with the highest temperature reaching about 2460 K. Modelling results show that the evolution of the explosion flame shape experiences four typical stages, ie spherical flame, finger-shape flame, flame with the skirt touching the side walls (ribs) and tulip flame, which are similar to the pattern of a duct explosion. The pressure in the gateroad remains the same as the initial value before the arrival of the explosion wave and then increases rapidly to the maximum value. Modelling results from this study will be used for the design of explosion arresting devices and mine seals in underground coalmines.CITATION:Liu, A and Ren, T, 2017. Computational simulation of gas explosion and its propagation in single entry gateroad, in Proceedings Australian Mine Vent Conference 2017, pp 181–188 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 28, 2017

By H. K. Lin, J. L. Oleson

The purpose of this study is to develop a mathematical model to describe the oxidation of cyanide with SO2as proposed in the Inco process. This research employed a direct method for measuring the change in cyanide concentration with respect to time as effected by varying concentrations of SO2, copper and pH. Developing this model may be applicable in determining optimum conditions in a process well known and used in the mining industry. It was determined that the reaction is first-order with respect to cyanide, SO2and [Cu+2].The reaction order is 0.15, or zeroth order with respect to [H+] at pH range from 8.0 to 9.5.The activation energy, Ea, is 21.6 kJ/mol. The overall rate equation, as determined through this study is: [ ]

Jan 1, 2004

By M. J. Sapko

The design requirements for mine ventilation seals have undergone a radical transformation in recent years, and these revisions have greatly increased the cost of the seal designs and their construction. For example, in the past two years, new federal regulations have increased the minimum design requirement to withstand explosion pressures from 138 kPa (20 psig) to 345 kPa (50 psig) or 827 kPa (120 psig), depending on whether the sealed mine volume is monitored continuously or not. Moreover, there is still a possibility that under certain conditions (such as detonations) even higher pressure requirements may be necessary. The ability of a monolithic, stand-alone mine seal to reliably withstand the full range of current and future pressures is becoming increasingly difficult and expensive. In an effort to develop a practical alternative, the West Virginia Office of Miners? Health Safety and Training (WVOMHST) and the National Institute for Occupational Safety and Health (NIOSH) have collaborated in a research effort to develop a practical, economic, and safe mine sealing technique that can enable mines seals to meet the full range of new explosion pressure design requirements. The basic idea is to use a barrier of common mine gob and rubble in combination with a conventional mine seal so that the pressure resulting from a gas explosion is reflected, absorbed, and attenuated, so the pressure on the ventilation seal is reduced. This paper discusses some concepts and preliminary test results for a ?Passive Mine Blast Attenuator? (PMBA) that can provide a useful alternative to increasingly larger and stronger stand-alone mine seals. Numerical models and full-scale experiments conducted at the NIOSH Lake Lynn Laboratory Experimental Mine (LLEM) show that the use of a PMBA can signficantly reduce the blast pressure and impulse on conventional ventilation seals. DISCLAIMER: This information is distributed solely for the purpose of pre-dissemination peer review under applicable information quality guidelines. It has not been formally disseminated by the National Institute for Occupational Safety and Health (NIOSH). It does not represent and should not be construed to represent any agency determination or policy.

Jan 1, 2009

Cretaceous to Cenozoic sedimentary basins in Western Southland include a wide range of non-marine and marine sediments, in a structurally complex setting dominated by major fault systems. A reassessment of their mineral potential confirms large quantities of nonmetallic minerals (limestone, aggregate, marl), and smaller reserves of bituminous coal, lignite, clays, and oil shale. Hydrocarbon potential is largely untested. Metallic minerals are present in trace amounts, apart from platinum group minerals and some detrital gold. In the offshore area, seismic data suggest the hydrocarbon potential is significant. The Orepuki area has the most interest onshore.

Jan 1, 1992

Ceremonies for the induction of four mining industry pioneers into the National Mining Hall of Fame will be held Saturday, Sept. 22, 2007 at the Charles F. Barber Pavilion (Museum Convention Center) in Leadville, CO. The four inductees are James Harold Courtright (1908-1986), Dr. Howard L. Hartman (1924-2002), Charles Washington Merrill (1869-1956) and Kenyon E. Richard (1915-1993). The inductions will bring to 197 the number of mining “greats” whose engraved photographs and biographical sketches are installed in the National Mining Hall of Fame.

Jan 1, 2007

By Emöke Imre

A point-symmetrical linear coupled consolidation model with displacement boundary condition is suggested for the description of the consolidation around the pile tip after pile penetration. Analytical solution is given. Main features of the solutions are predicted by the analysis of the system of differential equations and, the boundary conditions.

Jan 1, 2002

By Arthur Darby

The city of Kuala Lumpur was founded in 1857 by miners seeking tin near the confluence of the Klang and Gombak rivers. The rapid development of the city and surrounding area since independence has led to more rapid runoff during rainstorms and to gradual canalisation of the rivers with some restricted sections. The outcome has been more frequent and more severe floods (Abdullah 2006). At the same time the centre of Kuala Lumpur has become a modern inter-national city with tall office buildings, hotels, and shopping centres connected by a network of wide roads and commuter rail systems. With these the cost of dislocation during floods has risen as has the cost of making good damage afterwards. The Government of Malaysia considered these consequences unacceptable and sought ideas from the private sector for a solution. Potential solutions consisted of variations on the themes of bypassing the city centre with a flood relief tunnel or of providing off channel storage or a combination of both. Since under Malaysian law a tunnel cannot be constructed under private property unless this is first purchased or agreement reached with the owner, it was necessary for most of the tunnel alignment to run below existing heavily congested roads. After considering these facts Gamuda Berhad and MMC Berhad, two leading Malaysian development and construction companies, decided to propose to Government an innovative solution in which the tunnel would be used to carry road traffic except during floods.

Jan 1, 2008

By Charlie Wyche

The British Solomon Islands Protectorate continued developmental work on bauxite deposits on the Islands of Rennell and Vaghena. A feasibility study was completed by Mitsui Mining & Smelting Co., Ltd., and Pacific Aluminum Ltd. (a subsidiary of Conzinc Riotinto of Australia Ltd,), and negotiations with the Government were in progress. The Government will receive a 25% share if the project is realized. It was estimated that the Islands contain 60 million tons of bauxite with an alumina content of 45% to 50%.

Jan 1, 1980

By C. Stapel, AA Groningen, R. J. De Meijer

"In recent years the Environmental Research Group of the KVI has been developing a number of radiometric techniques that may be employed in mineral sand exploration. These techniques involve: radiometric fingerprinting for assessing sand provenances and mineralogical composition; thermoluminescence for dating and provenance determination of sediments; a towed seabed detector to map seafloors for radiogenic heavy minerals and assessing heavy mineral volumes; and simplified transport mechanism models to explain and predict heavy mineral concentrations.All techniques exploit the property that heavy minerals as a group contain concentrations of naturally occurring uranium and thorium that are a hundred to a thousand times higher than in light minerals. In this paper the physics of a number of methods will be described together with a number of results. Based on these results potential applications to mineral exploration and mining are discussed."

Jan 1, 1994

By I. Stanculescu

The consolidation of thick and very compressible soil deposits by stone columns associated with cast-in-place plain concrete columns, has been performed for shallow foundations of some heavy industrial structures. The reduction of settlements and increase of soil bearing capacity were thus ensured as a result of soft soil interaction with stone and concrete columns. The results of model tests and in situ large scale applications are presented. A calculation procedure is also suggested for foundation bases improved by the proposed method.

Jan 1, 2010

By T. Phiri, Antoine Floribert Mulaba-Bafubiandi

Microwave energy has been recently used in minerals processing to speed up the leaching process or to improve the liberation of targeted minerals (Al-Harahshed and Kingman, (2003); Bradshaw et al., (2001)). Applied to the roasting of sulphide minerals, microwaves allow the ?tunning? of calcine types and products quality in addition to the energy savings as opposed to the conventional roasting (Mulaba, 2006). As more than 85% of world zinc is produced through the ?roast-leach-electrowin? route, an attempt was made to optimize cost, energy and product quality for metal extraction process route. The use of microwaves was the alternative process route selected for the optimisation. Pyrite concentrate (0.17% Zn, 0.09% Cu, 35.71% Fe, 43.76% S) and sphalerite concentrate containing 43.81% Zn, 0.37% Cu, 3.86% Fe and 44.39% S were microwave roasted in a multimode cavity of 2.45 GHz with varying power levels and for different durations. The produced calcines were characterized using AAS, XRF, XRD and Mossbauer spectroscopy while the determination of residual Sulphur was used as products quality control tool to ascertain the degree of roasting achieved on the feed. The leachability of the produced calcines in HCl, HNO3, H2SO4 and HNO3 + HCl has been studied in terms of the best leaching yield, process kinetics economics and environmental aspect. With 800 W power for 30 minutes, ZnO and Fe2O3 were formed corresponding to a 70% sulfur removed from sphalerite and 80% from pyrite concentrates respectively. While the roasting of the above concentrates appeared to be a first degree processes, it was noticed that the microwave assisted roasting of sphalerite and pyrite concentrates yielded lower sample surface temperature for a shorter time (i.e.less than 30 minutes) microwave exposition. Longer time (more than 30 minutes) microwave exposure showed a linear increase in temperature in function of power level used. While optimum roasting conditions were found at 800W, 30 minutes, a 10% increase of sulfur removal was noticed while pyrite concentrate was microwave roasted. Sulfuric acid was seen to give higher leaching yield than nitric acid. Zinc dissolution was hindered by the presence of franklinite.

Jan 1, 2007

By Y. P. Chugh, J. Ma

Higher production, better safety standard, and potential for automation are some of the benefits of longwall mining. Today, longwall face advances at a faster rate exposing many diversified rock layers in a short period of time. It is now a serious challenge to cope with ground control problems such as roof falls, face and floor failure, and excessive shield loading as fast as possible to minimize production and monetary losses. In Illinois coal mines, the existence of weak floor strata blow the coal seam may pose additional problems related to floor heaving, shield base punching, and associated roof and face falls. In this study, the effects of weak floor on longwall ground control are analyzed using two-dimensional finite element models. A two-leg 635.6-ton (700-short-ton) yielding capacity shield is included in the models to evaluate the effects of different thickness and material properties of the weak floor. The study indicates that the thickness and material properties of weak floor have significant effects on shield loading, the distribution and intensity of front abutment stress, failure zones in the surrounding strata, roof-to-floor convergence, and floor punching by the shield base.

Jan 1, 2000

By David R. Morrey

During the past 50 years, significant research has been performed in the ecology and physiology of plants that colonize soils containing elevated concentrations of heavy metals. Similar work has also been performed on plants that are able to survive acidic and saline environments. Efforts have focused on the ecological analysis of plant communities that occur over a range of metalliferous mining wastes. Investigations have been performed on the mechanisms that allow selected varieties of plant species to survive in normally phytotoxic environments and on the potential applications of metal-tolerant varieties of plant species. The purpose is the remediation and reclamation of mining wastes and soils that contain unusually high concentrations of so-called heavy metals. Characteristics of some mineral wastes Metalliferous mining wastes present special environmental restoration problems because of their toxicity. Potential toxicities are mostly caused by residual metals derived from weathering of low-grade ore or the waste products of mineral processing. In cases where pyrite forms a part of the mining waste, acid generation by oxidation may exacerbate the toxicity problem by promoting heavy-metal mobilization in aqueous solution.

Jan 1, 1995

THE object of the air-tight stopping is either to prevent a current of fresh air from getting into the fire area, or to prevent an escape of fumes and gases from the fire area into the workings of the mine. In the former case all is "plain sailing," but in the latter case there are certain difficulties to be overcome.In the Broken Hill Proprietary mine there were two styles of stopping used during the last fire-brick and bag and the following were the chief points that determined the use of one in preference to the other:-If the required stopping were to be more or less permanent, bricks were used, also if the area to be blocked were large-bricks being so much lighter and easier to handle than bags filled with -skimps. If, however, the air contained much gas, a bag stopping was put up. Great difficulty was experienced in getting essentially surface men, such as bricklayers, to work where there was the; slightest trace of gas; miners, however, would willingly do the work, and a bag stopping could be built without skilled labour.In old drives and gangways, where there was the liability of settlement, the bag stoppings were preferable to brick. The slightest movement around the sides or foundations of the latter would cause cracks, thus rendering the brick stopping useless;whereas, in the former, there was a certain amount of elasticity.

Jan 1, 1909

The Clyde Power Project, and its Clutha Valley Development forerunner, has taken widespread investigations for various hydroelectric purposes both along the valley floors upstream from Alexandra and on the higher schist terrain. As part of this work the nature and extent of many of the alluvial deposits have been resolved and the ages established with varying precision. Gold values have been approximately appraised in some areas as an element of environmental assessment.

Jan 1, 1992

By Young-Dong Cho, Yonghun Jong, Dong-See Shim, Seokwon Jeon, Chung-In Lee

The most important operation in the tunnel blasting procedure is to create an opening in the face in order to develop more free surface in the rock mass. This operation is highly dependent on the cut holes. In general, the burn-cut or V-cut is commonly adopted to blast the cut section. But, these traditional methods often raise problems. There are instances (a) that the actual advance is considerably less than the designed advance depending on the rock mass, (b) that they cannot sometimes enlarge the free surface efficiently and (c) that the blast vibration resulted from the cut blast exceeds the allowable vibration level. In order to resolve the problems, many different kinds of the cut blast can be considered.

Jan 1, 2005

By Dale S. Preece, Matthew A. Reisenmay, Avione Northcutt

The ability to simulate the explosive effects of land mines on military vehicles is a valuable capability in the defense community. The current competency levels of such simulations, however, are in need of improvement. Experiments have been conducted to measure the explosive induced impulse of a land mine on a steel plate placed above the explosive charge. The purpose of this paper is to report the findings of a variety of simulation tests conducted in order to correctly predict the empirical impulse data gathered in corresponding experiments. The computer hydrocode, AUTODYN v5.0.01 (Century Dynamics, 2003), is the simulation code used to simulate, and process the results. The experimental data has not been made available to allow computer analysts to exercise their codes on the problem without the temptation to tweak parameters in order to match computer code predictions with experimental results

Jan 1, 2005