Search Documents

West Virginia ranks second in the nation in coal production, surpassed only by Wyoming, and usually accounts for 15 to 20percent of the nation's total annual production. Cod occurs in seams of minable thickness in all but nine of the state's 55 counties. There are two coal- producing regions, the northern field and the southern field. West Virginia coal is mined by both underground and surface methods. Underground mines in West Virginia account for a major portion of its coal production. Surface mines are generally contour operations and, especially in the southern field, are in steep slope areas, with slopes greater than 20 degrees. Many of the surface mines remove multiple seams. Recoverable reserves in West Virginia total in excess of 55 billion tons of bituminous coal. West Virginia's regulatory program was conditionally approved on January 19, 198 1. Its Abandoned Mine Land Program was approved February 23,198 1, with emergency authority granted on August 26,1988.

Jan 1, 1992

By Fred N. Kissell

In This Chapter [Measuring the gas emission from the coal Methane at the top of the silo Methane at the load-out area and Actions taken after a silo explosion] Methane accumulations in coal silos have resulted in the occasional silo explosion. These can be quite violent and dangerous because coal dust adds to the strength of the blast. However, with the appropriate precautionary measures, methane accumulations in silos can be greatly reduced. Mine Safety and Health Administration (MSHA) regulations at 30 CFR2 77.201 require that the methane content in the air of any coal silo be maintained below 1.0 vol %.3 Also, MSHA requires that methane tests be conducted before any electrical equipment is energized, unless a continuous monitor capable of deenergizing the electrical equipment is used.4 Measuring the gas emission from the coal. The first necessary step in dealing with silo methane issues is to measure the gas emission from the coal going into the silo. Such measure-ments allow one to estimate the silo ventilation needs and permit a comparison with the methane controls used at other mines that have similar gas levels. The gassiness of the coal can be measured by taking conveyor belt grab samples.5 Matta et al. [1978] measured the gas emission from conveyor belt grab samples using a simple desorption test. To conduct the test, they collected several grab samples of coal, weighing a few pounds each, from the conveyor belt entering the silo.6 They then sealed the coal into an airtight sample container that was equipped with a valve and short hose along with a pressure gauge. Every few hours they opened the valve and bled the emitted gas into a water-filled graduated cylinder that had been inverted and placed in a pan of water (Figure 11–1). The results are shown in Figure 11–2.

Jan 6, 2006

By Parry. V. F.

"SUMMARY This report reviews the status of the packaged-for industry as of 1941. A field study was made of 35 representative plants to obtain technics and economic data on different types of processes used to make packaged fuel in the Central States. The report includes a classification of processes, photographs of typical operations, designs of different plants, an analysis of costs of manufacture, and a study of the physical and chemical properties of fuel cubes.It was observed that many of the smaller plants were having troubles in the manufacture of packaged fuel as the price of materials and costs of labor advanced toward the higher levels of 1942. In some instances, the total cost of manufacture was as high as $5.00 per ton, while in the better, medium-sized plants it was approximately $3.25 per ton. The direct manufacturing costs, excluding investment and depreciation, ranged from $3.17 to $2.37. These costs permit almost no profit at small plants when packaged fuel sells for the same price as competing lump coal under conditions existing in 1941-42.It was found that the predominant troubles in plants were due to inadequate drying and insufficient mixing of the starch binder. It was ob¬served that in the better plants, where proper mixing of binder was attained high-quality packages were made if 50 to 70 percent of the moisture was removed in the drying ovens. Experimental data obtained in the laboratory show the relationship between the temperature of dry air and the time required to remove different percentages of moisture in wrapped orunwrapped coal cubes.The average physical and chemical properties of fuel cubes made by five processes are listed, and tentative standards for minimum physical qualities and methods for measuring quantity are giver."

Jun 1, 1944

By Edward L. Hajduk

During sonic logging quality control testing of the drilled shaft foundations for the replacement bridges crossing the Broad and Chechessee Rivers for SC 170 in Beaufort County, South Carolina, irregular signals were observed on a consistent basis near the shaft top elevations. These irregular sonic signals were attributed to access tube ?debonding?, which is the separation of the access tubing from the surrounding concrete. A total of 160 drilled shafts were installed for this project, of which 41 were evaluated using sonic logging testing. Both PVC and steel access tubes were used during the project to allow for sonic logging testing. This paper details the investigation of access tube debonding with time, discusses the solutions used to minimize access tube ?debonding?, and presents the results of the sonic logging testing for the entire project. The solution selected, installation of PVC along the pile length and steel access tubing within 40 feet from the top of shaft, allowed for reliable sonic logging to effectively evaluate the upper portions of the drilled shafts.

Jan 1, 2004

Large mining operations need equipment that consistently performs as expected. The most effective way of ensuring this is to have a defined life cycle with an optimised maintenance strategy. The determination of this life cycle is an economic decision, influenced by the construction and utilisation of the equipment. An effective life cycle costing (LCC) tool must be able to process the many variable factors involved.Many factors influence the costs that are associated with a machine over its life. The most variable of these are the costs of maintaining the equipment. Maintenance costs are dependant not only on the utilisation of the machine, but also on the strategy that has been developed to support the machine through its life. A combination of supplier support, component changes, regular servicing and unscheduled maintenance needs to be modelled, based on a variety of drivers. Traditionally spreadsheets have been used to model these factors, but the increasing complexity of the situation can make spreadsheets unwieldy and difficult to manage. A database solution that breaks each activity into its constituent components, links them to an associated mine plan driver and then aggregates the result is the ideal tool to provide a time based cost profile. The evaluation of a number of scenarios, representing different maintenance strategies/life cycles can be rapidly undertaken. Auditability through inbuilt tools is required to provide easy tracing of data. Use of the host company's account structure allows for reporting against the standard chart of accounts.

Dec 6, 2010

All of the coal resource in North Dakota is lignite. The lignite fields of North Dakota cover approximately 40 percent of the total area of the state, with reserves estimated to be 9.8 billion tons, two percent of the U.S. base. The first commercial coal mine in North Dakota opened in Morton County in 1873. As the railroads crossed the plains, the demand for coal increased. Coal for fuel was supplied by the state's underground mines. By 1884, North Dakota's lignite production had reached 35,000 tons. North Dakota was among the fist states to shift from underground to large-scale commercial surface coal mining. By 1927,40 percent of the total production was by surface mining, compared to 2 percent for the nation as a whole. By 1959,86 percent of the total production was by surface mining, while the national average was 22 percent. Since 1966, surface mining has been the exclusive coal production method in North Dakota. North Dakota's regulatory program received conditional approval December 15, 1980. Following approval of amendments to the program, it received full approval February 18, 1986. The Abandoned Mine Lands Program was approved December 23,1981.

Jan 1, 1992

The use of scrapers in mining and earthmoving operations is not new, in fact they are one of the earliest methods of bulk earthmoving. A single machine which can load, haul, and dump material with a minimum of ancilliary support is a highly productive and cost-efficient method of earthmoving. In recent times scrapers have been unpopular due to perceived problems and operational limitations, but the last couple of years have seen a resurgence in the use of scrapers in the Bowen Basin as a primary prestripping tool. The main operational limitation of scrapers is the economic operating range. maximum productivity and lowest cost per bcm is achieved on short leads, as the lead distance increases the cost per bcm quickly reaches and then overtakes that of an truck-excavator fleet. The geometry of a ætraditionalÆ coal mine does not readily allow short leads for prestrip fleets due to the nature of dragline stripping operations. The strip arrangement means that material has to be taken around the end of the pit, meaning a longer haul distance than the actual point-to-point distance between load and dump. This can be alleviated by using pit bridges, however these can cause spoil problems for draglines if not properly planned and have been avoided by many mines. Due to the economic haul distance limitation of scrapers, truck-excavator fleets have become the normal method utilised. Currently more geologically complex mines are opening up, which do not allow traditional down-dip strip mining to occur. Cross-dip mining methods allow for short leads between prestrip loading and dumping areas, hence scrapers and bulk doze are realistic alternatives to a truck-excavator fleet in the prestrip environment. Keeping the lead distance to a minimum a fleet of 657Æs can move material at a very low cost. The other main operational limitation of scrapers is the type of material that can be economically excavated. Hard material can lead to damage to the bowl, free-flowing sand will not readily stay in the bowl leading to reduced load factors. Ripping the material with a dozer prior to excavating can lead to improved loading time, and greatly reduced GET consumption. When considering scrapers for prestrip operations a number of things must be considered: is the lead distance within the economic haul distance? should twin power (push-pull) or single power (dozer pushed) scrapers be used? do I need to rip, what should I rip with? what ancilliary support is required? is there another system already available on-site which is currently under utilised? This paper considers the parameters under which large twin power scrapers are the most effective way of undertaking prestrip operations.

Jan 1, 2003

The coal-bearing strata of Oklahoma occur in the eastern part of the state over an area of 14,500 square miles, 20.7 percent of the state's total area. Commercially valuable deposits of bituminous coal cover about 8,000 square miles in seams ranging from ten inches to five feet thick. Estimated reserves in Oklahoma are 1.6 billion tons, representing 0.3 percent of U.S. coal reserves. The vast majority of coal mined in Oklahoma used in a single power plant within the state. Oklahoma gained primacy when its regulatory program was conditionally approved January 19, 1981. Authority for the state to administer the Abandoned Mine Land program was granted January21,1982. On April 30,1984, the Office of Surface Mining substituted direct federal enforcement of the inspection and enforcement portions of the Oklahoma program. This substituted enforcement was based upon a finding by OSM that Oklahoma had not operated the inspection and enforcement portions of its program effectively. As of January 1, 1986, Oklahoma inspection and enforcement authority was reinstated. Full program authority was granted to Oklahoma on January 14, 1986.

Jan 1, 1992

By D. Prince, G. Nollet

"Since 1994, Aur Ressources has operated Louvicourt mine, a zinc and copper mine close to Val d’Or, at a rate of 4300 t/d. Ever since the start-up of the plant, management has encouraged innovative approaches in reliability. The first of three papers will discuss the vibration monitoring program in place. The program will be described and two examples will be given: detection of a rolling bearing defect on a pinion driving the ball mill and identification of wear on the bearings of the flotation cells. Figures on the return on investment and the costs of a monitoring program will also be given.The second article will discuss the lubrication aspect. Since the establishment of a good monitoring and oil analyses, Louvicourt mine decreased its oil consumption by more than 38 000 L/yr. In addition, the company set up an oil regeneration system that restores the original properties of oil.The third article will cover the management aspect. Work organization as well as the management philosophy enabling the employes to push predictive technology to higher levels will be examined in detail. The key elements which made it possible for Louvicourt mine to position itself among world-class companies in the organization of maintenance will be discussed."

Jan 1, 2002

By J. F. Shao, G. Duveau, W. Z. Chen, O. Ozanam

In this paper, we present a sensitivity study for the numerical modelling of hydromechanical coupling around a shaft in partially saturated claystone. Two representative constitutive models have been used: an elastoplastic damage model (IDEPLML) and an elastic perfect plastic model based on the Hoek and Brown failure criterion (H&B). A series of comparative studies have been performed with respect to main parameters involved in coupling process (mechanical, hydraulic and hydric properties). The emphasis is put on the evaluation of induced plastic, damaged and failed zone due to excavation and drying process. Dans ce papier, nous présentons une étude numérique paramétrique du comportement hydromécanique couplé d’une argilite partiellement saturé, lors du creusement et de la maintenance d’un puit L’étude paramétrique porte à la fois sur le type de modèle et sur les principaux paramètres (mécaniques hydrauliques et hydriques) intervenant dans le couplage. L’accent est principalement porté sur l’évaluation des zones plastifiées autour de l’ouvrage lors de la désaturation. In unserem Beitrag geht es um eine digitale parametrische Untersuchung über das hydromechanische Verhalten eines teilweise durchtränkten Tons beim Abteufen und dem Betrieb von Schächten. Die parametrische Analyse konzentriert sich auf den Modelltypus und auf die wesentlichen bei der Verbindung wirksamen Parameter, d.h. die mechanischen, hydraulischen und hydrologischen. Der Schwerpunkt liegt auf der Bewährung der plastifizierten Bereiche des Bauwerkes während der Austrocknung.

Jan 1, 2003

By R Garzon

For resources projects with healthy net present value (NPV) and low cash flow volatility, conventional discounted cash flow (DCF) analysis will continue to provide the dominant investment decision-making criteria. However, DCF analysis can be biased because it often applies a single risk-adjusted discount rate (RADR) to compare the value of projects with different risk characteristics. Many of the difficulties with DCF modelling arise from analystsÆ inability to determine appropriate risk discounts and to estimate expected spot prices inputs for the commodities produced over the life of the project. Modern asset pricing (MAP) is a very valuable complement to DCF analysis in addressing some of these issues. Most papers dealing with MAP, however, while academically rigorous, tend not to be explicit in terms of practical application of this methodology in routine project evaluation. This paper has the objective of reviewing the MAP methodology and of demystifying its complexity, by providing a simple but realistic step-by-step evaluation of a mining project, comparing its DCF and MAP NPV values. The paper concludes that MAP provides a minimum, risk-adjusted æfloorÆ value, thus representing a valuable complement to any DCF valuation.

Jan 1, 2007

Ohio has an estimated 46 billion tons of coal beneath 12,000 square miles of the eastern third of the state. Recoverable coal reserves within this vast area are estimated at 21 billion tons, 3.2 billion tons of which have been mined since 1800. Ohio is the eleventh-largest coal- producing state in the nation and ranks third nationally in coal consumption. Coal resources in Ohio lie in as many as 60 identifiable coal seams along the northwestern flank of the Appalachian coal basin. Except where interrupted by minor faults and erosional discontinuities, these rocks dip gently and uniformly to the east, simplifying the mining methods needed to extract the coal. Fourteen of Ohio's 60 coal seams are considered to be important, although only a small number of seams are currently being mined. Ohio first enacted a surface coal mining law in 1948, requiring in part a $100 per acre reclamation bond. Ohio progressively strengthened its surface mining law in 1949, 1955, 1959, 1961, 1965,1972,1975,1978, and 1981. At the time of its enactment, Ohio's 1972 mining law was one of the most stringent in the country. This law also created a state coal severance tax of four cents per ton to be used for abandoned mine land reclamation. Ohio received primacy to regulate the surface coal mining operations within the state August 16,1982. Its Abandoned Mine Land Program was approved on the same date.

Jan 1, 1992

By E. P. Dowding, J. Schlocker, C. H. Fuchsman, R. R. Lloyd, Mahan. W. M., O. C. Garst, W. T. Rawles

"INTRODUCTION The United States, although the leading consumer of chromite, depends almost entirely on imports for its supply. For instance, the consumption during. 1941 amounted to 714,645 long tons, whereas the domestic chromite production, although the highest since 1918, was 12,731 long tons or only 1.78 percent of the domestic consumption. 9/ Domestic production was tremendously, accelerated,after 1941 by war demands; however, only a small proportion of this domestic product was of sufficient quality to be substituted for the high-grade imported chromite demanded for metallurgical purpose. Chromite is used largely for making ferrochromium, an alloy containing 60 to 70 percent chromium which is used in making alloy steels. Peacetime specification for ferrochromium required that it should contain 68 to 69 percent chromium. These specification were lowered to between 60 and 63 percent, chromium in 1941 to permit the use of lower-grade ores. The specifications for metallurgical chromite, used for making ferrochromium, were established first by the Metals Reserve Company at 48 percent Cr203 and a Cr. Fe. ratio of 3 : 1 but later were lowered to 45 percent Cr203 and a Cr : Fe ratio of 2.5 : 1. The ratio of chromium to iron in chromite is important, because the contained iron enters the alloy in making ferrochromium and, although an ore may contain the required 45 percent Cr203, it may contain too much to be suitable for ferrochromium production. The principal sources of domestic chromite are California, Oregon, Montana, and Alaska minor, small, and widely scattered deposits in another dozen States. Without exception, these deposits are low-grade, require beneficiation to produce a commercial product, and are not competitive with imported high-grade ore in normal times. Nevertheless, these deposits form strategic reserve, which must be utilized in periods of national emergency. Recognizing this fact; the Bureau of Mines for many years has undertaken investigations to develop methods of utilizing domestic chromite ores. The problem has been approached from three angles: (1) Mechanical methods of concentration; (2) beneficiation by chemical or metal¬lurgical methods; and (3) production of metallic chromium by electrolysis of solutions prepared from ore or concentrate."

Feb 1, 1946

By M. Hakala, P. Tolppanen

A method to predict stress-induced failures around excavations based on the mapped geological and rock mechanical information is studied. Totally of 7 km of newly excavated tunnels are mapped in the Inmet’s Pyhäsalmi mine in Finland at depth between 1000 - 1440 m from which the results and conclusions from the firstly mapped 1.7 km of tunnels are reported. The main rock type at the site is very hard volcanite having uniaxial compressive strength of 230 MPa in median and GSI-value 72 - 80. The maximum in situ stress around the tunnels is 65 - 85 MPa. The prediction of observed stress failures was preceded by comparing elastic 3-D simulation results of tunnels with three statistical yield criteria. Read’s or Hoek & Brown’s yielding criteria are found the most relevant, though, the effect of anisotropy was found to be significant. The most important parameters having a correlation with stress failures are the tunnel orientation and the foliation of rock. Also, the rock type and its strength, tunnel shape and the geological anomalies have their effects. Further, a delay time on mapping was found to clearly diminishing of the most violent failures. Une méthode de prédiction des contraintes à la rupture autour d'excavation, établie sur la base de cartographie géologique et d'information sur la mécanique des roches, à été étudiée. Au total, 7 km d'un tunnel nouvellement percé à une profondeur de 1000 à 1400 m ont été cartographiés dans la mine de Inmet’s Pyhäsalmi en Finlande. La roche principale du site est une vulcanite dur ayant une résistance à la compression uniaxiale de 230 MPa (valeur moyenne) et une valeur GSI de 72 - 80. La contrainte in situ maximale autour du tunnel se situe entre 65 et 85 MPa. La prédiction des contraintes à la rupture observées a été évaluée en comparant les résultats d'une simulation 3D d'un tunnel avec trois critères de limite d'élasticité statistiques. Le critère de limite d'élasticité de Read ou de Hoek & Brown’s se trouvent être les plus important, même si les effets de l'anisotropie sont significatifs. Les paramètres les plus importants ayant une corrélation avec la rupture sont l'orientation du tunnel et la foliation de la roche. De plus, le type de roche et sa résistance à la compression, la forme du tunnel et les anomalies géologiques ont aussi leur importance. Finalement, un délai dans la cartographie résulte en une diminution nette des ruptures violentes. Basierend auf kartierten geologischen und felsmechanischen Informationen, wird eine Methode untersucht, um spannngsbedingtes Versagen um Ausbrüche herum vorherzusagen. Insgesamt werden 7 km neu ausgebrochenen Tunnels in einer Tiefe zwischen 1000 und 1400 m in der Inmet Pyhäsalmin Mine in Finnland kartiert. Das hauptsächlich vorkommende Gestein ist sehr hart und vulkanischen Ursprungs mit einer mittleren einachsialen Druckfestigkeit von 230 MPa (Medianwert) und einem GSI-Wert von 72-80. Die maximale In-situ-Spannung im Tunnel beträgt 65-85 MPa. Die Vorhersage von beobachteten Spannungsversagen werden weitergeführt indem man elastische 3-D-Simulationsergebnisse von Tunneln mit drei statistischen Fliesskriterien vergleicht. Read's oder Hoek's Fliesskriteria werden dabei als die relevantesten Kriterien angesehen, obwohl auch der Effekt der Anisotropie als wesentlich erachtet wird. Die wichtigsten Parameter für eine Korrelation von Spannungsversagen sind die Orientierung des Tunnels und die Schieferung der Gesteinsschichten. Desweiteren haben Gesteinsart, Tunnelprofil und geologische Anomalien ihren Einfluss. Ausserdem zeigt sich, dass eine Verzögerung bei der Kartierung die ausgeprägtesten Versagen deutlich verringern.

Jan 1, 2003

By Henry Louis

THE work performed by the Royal Commission on Mining Subsidence is likely to prove of permanent value, less perhaps for the conclusions it has reached and for the recommendations it has based upon these than for the admirable exposition which it affords of the law concerning mining subsidence and of the legal status of the person who has suffered damage by reason of such subsidence, as also of him whose working has caused the damage. The Commission was appointed by Royal Warrant in the middle of 1925 and delivered its final report in the middle of 1927. The terms of reference to the Commission were as follows: "To consider the operation of the law relating to the support of the surface of the land, and of buildings or works on or under the surface, by underlying or adjacent minerals; to enquire into the extent and gravity of the damage caused by subsidence owing to the extraction of minerals and the incidence of the resulting liability; and to report what steps should be taken, by legislation or otherwise, to remedy, equitably to all persons concerned, any defects or hardships that may be found to arise in existing conditions."

Jan 1, 1929

By Hongyang Cao

The iron constituents selectively separated from the modified copper slags by magnetic separation and flotation.were studied. The results of magnetic separation for modified copper smelting slags show that the grinding size, current intensity and dispersant agent had great influence on grade, and recovery ratio of TFe in preparation concentrate; The results of flotation for magnetic concentrate show that the positive flotation of sodium oleate negatively upgrade the grade of magnetic concentrate, but the reverse flotation of lauryl amine and soluble starch are effective. The grade of TFe can reach 54% and the recovery ratio can reach about 90% in magnetic concentrate, when the grinding size is 45.8µm and the current intensity is 2.5A. The optimal effect is obtained by using lauryl amine as collector and soluble starch as depressant to reverse flotate magnetic concentrate, and the grade of TFe is upgraded 2.37%.

Jan 1, 2009

By E. M. Hill, H. K. Lin, J. L. Oleson

When activated carbon is used for recovering gold in gold industry, carbon fine materials are generated in stripping, acid-washing and kiln regeneration circuits. The carbon fines at the Fort Knox mine, Fairbanks Gold Mining, Inc., contain up to 0.68 kg/t (20 oz/st) of gold. In laboratory tests, gold in the carbon fines was effectively transferred to coarse virgin carbon when the carbon fines were mixed with virgin carbon in cyanide solution at a cyanide concentration higher than 0.10%. A plant-scale test conducted at the Fort Knox mine also shows effective gold transfer from the carbon fines to virgin carbon with a 95% gold recovery in a two-stage gold transfer process.

Jan 1, 2002

By W. S. Landers

Nine high-volatile bituminous Utah coals were carbonized singly and in blends with low-and medium-volatile bituminous coals. Of the 9 coals, 2 are in commercial use as the base coals in blends that produce industrially accept-able metallurgical coke, while 7 are regarded as weakly coking and are not used commercially in coking blends. The carbonization tests were made in a la-inch diameter, cylindrical retort, using 50-pound charges. Sunnyside coal blended with autogenous char generally produced larger and stronger coke than was yielded by straight Sunnyside coal. The volatile matter of the char and the concentration of the char in the blend appear to be important parameters influencing coke size and strength. A blend of 10 per-cent autogenous char of 7.2-percent volatile matter with Sunnyside coal yielded coke that was larger, stronger, and of higher apparent specific gravity than coke produced from an industrial coke oven blend consisting of 15 percent medium-volatile coal and 85 percent Sunnyside coal.

Jan 1, 1967

The 115-year history of the Hall-Heroult process for production of aluminium has been characterised by a sustained technology-driven improvement in costs and productivity. In the past decade the industry has effectively transferred best practice into older technology with improvements through computer control of the process, and redesign of cell linings using computer modelling . Incremental development is now at the point where diminishing returns will apply for further technical improvement effort however, until the gap between technical limits and current best practice is addressed through major process redesign. The process remains a long way short of its technical limits in energy consumption, carbon anode consumption, cell life and product purity. Investment cost in new capacity is very high, supporting the retention of older and less efficient technology and hence limiting the application of best practice in environmental performance and occupational health exposure. The industry is a major emitter of greenhouse gases yet the process has the potential to release oxygen as the primary waste. All of the above issues will be addressed in the new century, but only through commitment to the necessary long-term research and development that is required to achieve a redesign of the process.

Jan 1, 2000

By S. G. Hardcastle, C. K. Kocsis

Ventilation is an expensive prerequisite for underground mining. Current mining trends, including increasing depth and mechanization and more stringent health regulations would generally dictate that more air volume is required in order to provide good working conditions underground. However, any increase in the mine’s intake airflow can produce a disproportionate increase in power consumption and hence operating costs due to the cubic relationship between the sup-plied air power and the airflow (Power a Flow3). Furthermore, forecasts of significant increase in energy prices and new commitments with regard to reductions of greenhouse gas(GHG) emissions, determined the mining industry to look into developing new concepts, design tools and incorporate the latest mining technologies in order to lower capital and operating costs while meeting commitments regarding GHG emissions. The advances in computing power and modelling software now make it possible to design, model and schedule a mine from opening to closure. A developing trend is to design and plan the mine by means of orebody modelling software, followed by using discrete-event simulation techniques to predict production rates and evaluate various operating scenarios throughout the life of the mine. The authors are currently evaluating how such process simulators could be adapted in order to forecast the need for materials or a specific resource, and one of these would be the mine’s “life-cycle” airflow demand as a function of scheduled production rates and mine operating characteristics. Further to this, based upon the mine’s life-cycle airflow demand schedule, the ventilation system could then be designed using a mine ventilation simulator. This new design approach would integrate in parallel the development of the ventilation system with the current mining conditions, therefore, heading towards “develop-as-you-go” as opposed to developing the system for final requirements with high upfront costs. This new ventilation system design criteria would also incorporate the use of the “ventilation-on-demand” technology, which will further lower development and production costs and implicitly, the mines’ GHG emissions.

Jan 1, 2004