Search Documents

By Walter Harvey Weed

CONTENTS. [ ] INTRODUCTION. THIS paper deals with certain ore-deposits whose structural features or mineral contents (or both) result, directly or indirectly, from igneous intrusions and their after-effects. It is largely a discussion of contact metamorphic ore-deposits based upon the physical changes in rocks due to contact action. It involves a classification of ore-deposits only so far as is abso-

Jan 1, 1913

By A. M. Bauristhene

Ti-64, which accounts for more than 50% of the worldwide titanium tonnage, has found commercial importance in industries requiring components with high specific strength and resistance to corrosion. Investment casting is the preferred production method due to the difficult machinability of the alloy. This study was aimed at investigating the mechanism and the extent of alpha case formation on Ti-64 components cast using the investment casting method with YFSZ (yttria fully-stabilized zirconia) shell moulds after vacuum induction melting. The extent of the reaction between the mould hot face and the molten metal has been studied by varying parameters such as soaking temperature and mould hot face composition, and examining their effects on the reaction with the mould. An increase in the soaking temperature had an effect on the alpha case, both in appearance and hardness, but had no effect on contamination levels by carbon, oxygen, and nitrogen. The depth of alpha case increased with soaking temperature, increasing from 35 µm to 161 µm with an increase in temperature from 1200°C to 1400°C. The micro-hardness profiles provided insight into the effect of the alpha case on the mechanical properties of the Ti-64 alloy by displaying hardness values of 1000 HV0.1 and above, but could not be solely utilized to determine the alpha case penetration depth due to microstructural differences in the unaffected Ti-64, in particular the martensitic microstructure that formed with a fast cooling rate from a higher temperature. Levels of expected contaminants such as Zr, Y, 0, and C were low. The addition of the colloidal zirconia binder affected the interfacial reactions. YFSZ proved to be a thermodynamically stable refractory material, with the alpha case possibly forming as a result of segregation.

Jan 1, 2013

By Carter NB

A statistically-designed experimental program has been used to study compositional and processing variables which influence the development of strength and reducibility of iron ore pellets. The effects of chemical composition and processing variables were investigated by indurating laboratory-made green pellets, of known composition, under approximately isothermal conditions in a pot- grate simulator. Some findings from a six- variable study are summarized in the form of contour diagrams and emphasize the importance of interactions between the variables. Production of strong, highly reducible pellets is possible over a considerable range of combinations of temperature and firing time. Abrasion index (AI) and cold compression strength (CCS) improve as both these variables increase, but reducibility (R) declines, so a compromise is required. When the lime level is too low to form enough slag for bonding, the AI and CCS may be inadequate. Larger additions of lime tend to improve AI and CCS, with only slight effects on R. Finer grinding of the balling feed (i.e. higher Blaine index) tends to improve Al and CCS without

Jan 1, 1980

THE great development of the mines and metallurgical works of this country during the last few years, accompanied as it has been by the investment of enormous sums of money in purchasing lands, and in the erection of improvements, requires that advantage should be taken of the accumulated knowledge of engineers, superintendents, and' others, in mastering &he problems which are constantly presenting themselves for our action. Among those may be mentioned the consideration of more economical systems of mining in our coal and metal-liferous mines, improved methods of transportation above and below ground, unwatering and ventilating mines, the mechanical preparation of coal and other minerals, the various metallurgical processes, and, in fact, every question tending to the attainment of two great objects : 1st. The more economical production of the useful minerals and metals. 2d. The greater safety and welfare of those employed in these industries. In European countries, where the arts of mining and metallurgy have long been the subject of the most careful study, no means have been found so effectual in attaining the end above proposed as the free interchange of experience among those actually engaged in these industries, and this object has been accomplished, mainly, through the medium of institutes, associations or societies, composed of those engaged in these occupations, and by the periodical publication of essays or papers, communicated to such societies by their members. I t must be evident to all practical men that the interchange of the varied experience of those engaged in such occupation in this country could not fail to advance very materially the desired objects; it is, therefore, proposed to establish an American Institute of Mining Engineers, which will hold its meetings periodically in the great mining and metallurgical centers, where works of interest, such as mines, machine shops, furnaces, and other metallurgical works, can be inspected, and the members exchange their views, and consult for mutual advantage upon the difficulties encountered by each; these transactions or proceedings, when published, would form a most valuable and greatly-needed addition to our professional literature. I t is proposed that a meeting of those sympathizing with the object above mentioned shall be called for the purpose of organizing such an association, the place and time of meeting being Wilkes-Barre, Pa., and the month of April or May. Communications indicating the opinion and wishes of all, both as to these points, and also as to the organization and objects of the Institute, will be gladly received by any of the undersigned, and a notice of the date of meeting, which will be arranged to suit the greater number, will be duly communicated. Any

By Chick Kerkering, Stephen Iverson

Perimeter control blasting is common in civil construction projects but not as common in mining. A poorly designed and executed underground mine development blast design can result in unwanted wall rock damage. This damage increases the risk of rock falls and injury. With the availability of good drilling equipment, it is a simple matter to add the few extra holes needed to change conventional drifting into drifting with perimeter control.

Jan 1, 2008

The South Junction deposit of St Barbara Mines Limited was discovered in 1989 by the geologists of Ross Atkins Mining.The deposit occurs in the lower part of the Gabanintha Formation of the Lukes Creek Group in the Mt Magnet -Meekatharra greenstone belt. Country rock is predominantly talc-chlorite schist. Gold mineralisation is associated with north-south shear zones, quartz-carbonate-fuchsite alteration of the ultramafic rocks and in particular close to deeply weathered quartz-albite porphyry. For a detailed description of the geology of the South Junction Deposit see Fiala (1992).

Jan 1, 1993

The first mining in Western Australia probably commenced some 40 000 years ago when Aborigines arrived and began quarrying stone for tools and weapons, and ochre for decoration. The earliest documented mining by European settlers took place in 1850 on a small lead vein in the bed of the Murchison River, reported by the explorer A C Gregory. However, it was the discovery of gold in the Kimberley region in 1885 that first drew wider attention to the State's mineral potential.

Jan 1, 1992

By Barlow S

The Kelian Gold mine project won two excellence awards from the Victorian Division of the Institution of Engineers, Australia. It was a challenging project, fast tracked in a remote and inhospitable tropical environment. The creation of a profitable and efficient mine was a significant engineering and project management achievement. The difficulties encountered and the way they were managed provide valuable lessons. These include the importance of sufficiently detailed engineering in all aspects of the job to enable the best estimates possible to be prepared during feasibility studies, the need to prepare the project scope and execution plan with disciplined and rigorous attention to detail by a highly experienced team and the value of identifying, assessing and mitigating risk and uncertainty during execution. The practical benefits of applying these lessons were demonstrated in the successful management of technical uncertainty on the recent diversion of the Kelian River to allow the expansion of the Kelian mine.

Jan 1, 1997

On-line radioisotope gauges determine information on the characteristics of ore to enable improved control of processing operations. In the metalliferous mineral industry, in-stream analysis systems based on radioisotope X-ray techniques determine concentrations of valuable minerals at various stages of the concentration process. In the coal industry, on-line gauges determine ash and moisture contents, and the specific energy of coal.In-stream analysis systems developed in Australia are installed in about 30 mineral concentrators. Their use has led to the increased recovery of valuable minerals, and the time taken to recover the cost of installation is usually several months. The savings to Australia resulting from use of these analysis systems is estimated to be more than $A 15 million per year.Australian experience in the training of mineral industry personnel shows that the most effective approach is to combine courses on nuclear techniques and control of processing operations. This is the basis of Australia's contribution to the minerals sub-project of the United Nations Development Program (UNDP) Industrial Project.

Jan 1, 1985

By Mauk JL, Arehart GB

Quartz veins from the Martha Hill epithermal gold-silver deposit, Waihi, commonly exhibit crustiform banded textures. Visual differences observed between bands are primarily the result of a 1 to 1500 ¦m variation in quartz grain size. Quartz band textures are dominated by anhedral interlocking quartz mosaics, commonly associated with minor adularia and sulfide phases; these textures are interpreted to be products of amorphous silica crystallisation. The occurrence of rhombic adularia suggests that prolonged boiling influenced parent fluids. In contrast, the presence of coarsely crystalline bands, made up of subhedral to euhedral quartz grains, infers primary crystal growth from solution; evidenced by the occurrence of growth-zoned quartz within these bands. There is a narrow range of 3.3%o in 618Oq,,,,,= between maximum and minimum isotopic values for the deposit. Significant overlap in 618Oqu,, values are observed between the Martha and Welcome lodes. However, statistically significant and commonly systematic differences do occur between individual bands analysed in most samples. Temperature fluctuations may be the dominant factor responsible for observed inter-band variation.

Jan 1, 1995

By R. V. Ramani, S. Shankar

The phenomenon of re-entrainment is seen in environments such as sand dune formation, soil erosion, fugitive dust emission and the spread of radionuclides from accidents involving nuclear weapons. A thorough review of existing literature reveals that work on re-entrainment of dust in mine atmospheres is scant. The present study was undertaken as a part of ongoing research at the Generic Mineral Technology Center on Respirable Dust at the Pennsylvania State University on the development of methods to predict ambient dust concentrations in mine atmospheres (Ramani, 1983). The contribution of re-entrainment to the spatial and temporal concentration of dust in mine airways is being studied. The research has included wind tunnel and in-mine studies. A set of seven experiments was performed under controlled conditions in the US Bureau of Mines' Lake Lynn Laboratory mine. Two types of source coal dust, anthracite and bituminous, were subjected to various airflow rates and were subjected to walking by two different individuals. Six sets of instruments were used along the test section for sampling airborne particles. The average air velocity just above the coal dust bed varied between 2.1 to 3.2 m/sec. Due to re-entrainment as a result of the airflow conditions, the average respirable dust concentration in the center of the mine airway increased to 0.09 mg/m3 (standard deviation = 0.03 mg/m3) from an initial value of 0.02 mg/m3. The concentration of all (total) airborne dust increased to 0.17 mg/m3 (standard deviation = 0. 10 mg/M3) from an initial value of 0. 02 mg/m3. The action of people walking, however, caused higher amounts of re-entrainment. The average concentration of respirable and total dust at the center of the mine airway increased to values of 0. 28 mg/m3 (standard deviation of 0.12 mg/m3) and 1.53 mg/m3 (standard deviation of 1.0 mg/m3), from initial values of 0.03 and 0.05 mg/m3, respectively. It was observed that the dust concentrations were much higher near the floor, immediately at the end of the coal-dust bed. Depending on the level of activity and the amount of dust deposited in the mine airways, re-entrainment may become an important source of airborne dust in areas away from the point of actual mining.

Jan 1, 1996

By P. S. Baker

CRU estimates that the global supply of metallurgical grade alumina (MGA) grew by 5 percent during 2005 to a little more than 61 Mt (67 million st). About 30.7 Mt (33.8 million st), or 50.3 percent, of that originated from Oceania (principally due to the commissioning of the CAR refinery in Australia) and Latin America. In this context, Chinese production surged by 20.5 percent year-on-year to 7.7 Mt (8.5 million st) on the crest of a 17-percent rise in that country’s primary aluminium production. Meanwhile, on the demand side, there was a 6.7 percent climb year-on-year in global consumption to 62.3 Mt (68.6 million st). This reflected a healthy demand for primary metal from aerospace, construction, packaging and passenger transportation (to a lesser degree) in the United States, China, Brazil, South Korea and India. So there was an overall supply deficit of more than 1.2 Mt (1.3 million st). This, combined with an 18.3-percent diminution in closing stocks (down to 35 days of requirement), lifted the average spot price of MGA by 17.6 percent year-on-year to US$448/t (US$406/st).

Jan 1, 2006

Jan 1, 1966

By D. B. Spears

The sillimanite group includes the aluminosilicate minerals sillimanite, kyanite and and alusite, all of which have the same chemical composition (Al2SiO5). This discussion also includes the closely related mineral, mullite(about Al6Si3O15), which, although rare in nature, is produced artificially for industrial use. All of the minerals in this group have a low coefficient of thermal expansion and high corrosion resistance. This makes them desirable for refractory applications, especially in the steel and foundry industries. Other uses include electrical insulators, abrasives and household ceramic products. The minerals in the sillimanite group decompose with an irreversible expansion at temperatures between 1,300° C and 1,600° C (2,372° F and 2,912° F). Sillimanite and and alusite have relatively small expansion on decomposition (4 percent to 6 percent) and, therefore, can be used as aggregates in refractory products. Kyanite’s expansion on decomposition is large (18 percent). So it is sometimes used to balance shrinkage of other materials such as clays in refractory mixtures. For applications requiring high-temperature volume stability, mullite is more desirable. As an additive, mullite improves resistance to creep and corrosion, and imparts thermal and electrical insulating properties.

Jan 1, 2005

By F. J. Brenner

The Slippery Rock Watershed Coalition was organized to restore a 70 km2 portion of the headwaters of the Slippery Rock Watershed in northwest Pennsylvania. Thirteen passive treatment systems have been installed with engineering and funding provided by private industries, county government and the Commonwealth of Pennsylvania. In addition, experimental systems have been installed at the Jennings Environmental Education Center which, in addition to monitoring the systems installed within the watershed, provide an array of educational and research opportunities for secondary, college and university students. The coalition sponsors an annual seminar for students to present the results of their research and field trips for public officials and private citizens to learn how public and private partnerships work together to restore the Slippery Rock Creek watershed.

Jan 1, 2002

By P. Mills

The four top barite-producing countries in the world are China, India, Morocco and the United States. China is currently the largest exporter of barite followed by India. More than 95 percent of the barite mined today is used by the petroleum industry as driller’s mud. The rest is used in the industrial market and the medical field. Most of the barite mined in the United States is in Nevada. This year, mining activity has increased due to an increase in oil exploration/development. This was caused by an increase in the crude oil prices.

Jan 1, 2005

By R. L. Virta

Sixteen companies mined fuller’s earth in 11 states during 2004. Production during 2004, based on a preliminary survey of fuller’s earth producers, was 3.96 Mt (4.3million st) valued at $340 million. This compared with3.6 Mt (3.9 million st) during 2003, valued at $346 million. The 3.96 Mt (4.3 million st) probably includes some crude clay tonnage. And production of finished product probably was closer to 3.2 Mt (3.5 million st) in 2004. Georgia was the leading producer state of attapulgite-type fuller’s earth, followed by Florida. Georgia also was the leading producer state for montmorillonite-type fuller’s earth. It was followed, in descending order, by Mississippi, Missouri, Florida, Virginia, Illinois, California, Tennessee, Kansas and Texas.

Jan 1, 2005

By Lyle Dennis

Emphasis on increased production while maintaining rigid quality standards has necessitated a change in blasting technology at Dacotah Cement's limestone and gypsum quarries. The following three methods implemented during the past three years have yielded an increase in production through improved fragmentation.

Jan 1, 1996

By I. Douni

The aim of this study is to synthesize hydrated compounds of calcium silicate (tobermorite) using as siliceous source perlite milling process wastes, containing more than 70% of SiO2. Calcium silicate hydrates are mainly used for construction of lightweight building materials, plasters, tiles and filters. The effect of temperature, time and particle size of perlite on the quality and composition of the solid product was studied. The solid products were characterized by X-ray Diffractometry, Differential Thermal Analysis and the amount of Acid Insoluble Residue. The synthesis of tobermorite was per-formed by the hydrothermal treatment of perlite waste with a saturated calcium hydroxide solution at a molar ratio CaO/SiO2 of 1, liquid to solid ratio 10 mL/g and 1% w.t. NaOH addition. Three experimental sets were performed. In the first series of experiments the synthesis temperature was kept constant at 205°C while the synthesis time varied from 0.5 h to 24 h. In the second experimental series the synthesis time was kept constant at 2 h while the temperature varied between 150°C and 245°C. In the third experimental set the temperature was 205°C and the reaction time was 2 hours and two perlite waste size fractions were used, a coarse (d50=18 µm) and a fine grained one (d50=8 µm). Reaction products consisted of semicrystalline calcium silicate hydrate (I) and crystalline Al-substituted tobermorite or a mixture of both. An isomorphic Si4+ ions substitution with Al3+ ions in the hydrated calcium silicate lattice was detected by thermal analysis. The experimental results show that good quality crystalline Al-tobermorite can be produced after 6 hours of autoclaving at 205°C or after 2 hours of hydro-thermal treatment at 225°C. Generally, the in-crease of synthesis temperature or time favors the crystallization of calcium silicate phases and enriches them in aluminum. The use of fine grain size perlite is more efficient for the hydrothermal synthesis of calcium silicate hydrates.

Jan 1, 2006

By B. C. Blake

IN general, billet-type or long slender ingots are used when it is desired to produce directly from the ingot in one conversion a product of medium or small cross-sectional area. They are designed to eliminate the blooming and billet-mill stages of the usual procedure. As used at Connors, they constitute a means of keeping a continuous rolling mill busy in the production of high-quality small rods, small angles, hoop stock, baling ties and concrete reinforcing rods without the need for a blooming or billet mill. They represent sound steel with the best surface that is commercially practical to use in the rolling of small continuous mill products.

Jan 1, 1947