Search Documents

By Yunnen Chen

This work concerns the removal of zinc(II) and COD by means of sawdust obtained as a by-product from locally used wood. The zinc(II) and COD removal study has been carried out batchwise where the influence of physico-chemical key parameters such as tree species, pH value of solution, temperature and contacting time and dosage of adsorbent have been considered. The maximum percent removal was attained at pH 9 all for Zn(II) and COD after about 60 min. The adsorbent can be effectively desorption using 0.1 M HCl. The experimental results showed that ion exchange maybe the major adsorption mechanisms for binding the divalent metal ions to the sawdust. Sawdust was a potential adsorbent for the removal of Zn(II) from the effluent of electroplating industry.

Jan 1, 2009

By M. J. Gilbey

London Underground is the oldest and one of the deepest Metros in the world. The temperature of the Underground has been increasing over the last 100 years, mainly as a consequence of increases in train service. Further increases in train service are planned in the coming years to meet the predicted growth in passenger demand. Unabated, the additional service will increase temperatures on the Underground. London Underground Limited (LUL) has therefore set up the Cooling the Tube Programme (CTP) to tackle the issues of thermal conditions on the Underground. Some of LUL?s studies and cooling methods have borrowed experience and techniques from the mining industry; some of methods used or proposed may in turn be of interest to the mining community. This paper presents a background into the sources of heat on the Underground network, the manner in which the heat is presently dissipated, the analysis of future temperatures and criterion and a number of means and methods being used or proposed to cool the network in an environmentally sensitive manner.

Jan 1, 2009

Where space is limited, as it is throughout most of the northeastern United States, new construction either takes place high above street level, or below it. In Lower Manhattan, NY both kinds of expansion can be found in abundance. That is good news for the nearly 200 attendees at the George A. Fox Conference, presented by the Underground Construction Association (UCA) of SME at the Graduate Center, City University of New York, on Jan. 30. Among the many projects taking place in Lower Manhattan?s massive trans-formation process, are expansions to the city?s vast underground network of subways and other tunnels. ?New Yorkers either live on the ground or below it,? said keynote speaker Charles J. Maikish while explaining how an attempt to build above street level walkways never caught on in the city. Maikish is the executive director of the Lower Manhattan Construction Command Center. His job is to oversee the $22 billion project that will transform the island by 2010. From the construction of Freedom Tower at the site of the fallen World Trade Center buildings, to the expansion of the Second Avenue Subway, the extension of the East Side Access, No. 7 line, the new trans-Hudson line and numerous waterway tunnel expansions, including City Water Tunnel No. 3, the task Maikish is charged with is a huge one. He is primarily responsible for coordinating the scheduling and staging of the overall rebuilding plan, along with the day-to-day coordination of construction work down-town. He places particular focus on mitigating impacts on the environment and mobility, maintaining and improving access and alleviating congestion of any kind related to construction. At the time of the Fox Conference, there were 59 projects under way in Manhattan. All of those projects need things like concrete and steel delivered to sites in very tight working environments. And some need the equipment in even tighter spaces. ?This is not just about the recovery of Lower Manhat-tan (from the 2001 terrorist attacks) but this is a plan to restore it and to maintain its integrity,? said Maikish. ?I think that is the appropriate response to the terrorist attacks.? When Freedom Tower is completed, it will stand 541 m (1,776 ft) about the skyline. That will be a strong statement to the world about America?s strength. But it is the work that takes place much lower that was of interest to the conference attendees. On this respect, Maikish said Manhattan?s efforts below ground aim to provide relief to the city?s street level congestion and to make sure Manhattan ? already essential to the economy of the United States and the world ? stays current by upgrading the existing telecommunications and technological network while also allowing room for growth in that area.

Jan 1, 2007

By W. E. Coughlin, R. L. Faverty, F. H. Lightner

Introduction The intent of this paper is to present the general strategy and method of implementation to achieve a "fast-track" mine development. The major objectives of a "fast-track" or rapid development schedule are to minimize front-end development expenditures and to realize an early cash flow from operations. The Borealis project of Houston International Minerals Corp. (HIMCO) is used as the working example to illustrate the development schedule. Borealis is a 2.3 kt/d (2,500 stpd) gold-silver heap leach operation near Hawthorne, NV, Pre-Feasibility Planning Proper early planning and identification of priority items were necessary to expedite project progress. On April 1, 1978, HIMCO leased the rights to the Borealis prospect and initiated exploration activities almost immediately. Since Borealis was showing excellent potential for mine development, an effort to clear the way environmentally was initiated during the summer of 1979. With the Borealis properties located within the Toiyabe National Forest, the US Forest Service (USFS) was recognized as the "lead" or respon¬sible agency for addressing the environmental issues. Early scoping of the environmental issues by both HIMCO and the USFS allowed HIMCO to take the initiative and address two potentially critical issues-archaeological and biological. Third party consultants, agreed upon by HIMCO and the USFS, were contracted to conduct archaeological and biological surveys. Desert Research Institute of Reno, NV, provided archaeological services, and JFL & Associates of Boulder, CO, provided biological services. These efforts began in the fall of 1979 and continued through the summer of 1980. Conservative Design Criteria By adoption of conservation design criteria, flowsheets and processing data required for detail engineering were firmly established with a minimum of impact on schedule. On Oct. 21, 1980, HIMCO formally initiated a feasibility study to evaluate the Borealis project. Four organizations were contracted for particular scopes of work: • John T. Boyd Co.: Ore reserve estimation, preliminary mine plan, and mine capital and operating cost estimation. • Bechtel Civil and Minerals: Conceptual engineering, processing capital and operating cost estimation. • Hazen Research Inc.: Metallurgical testing. • Sierra Pacific Power: Cost estimation for power supply. Metallurgical testing and conceptual engineering of both heap and agitation leach flowsheets were investigated concurrently. Numerous economic evaluations were conducted for both heap and agitation leaching at varying production capacities. The results indicated a heap leaching flowsheet treating 454 kt/y (500,000 stpy) yielded the best economics and was compatible with the "fast-track" development goal. Conservative design criteria was established to provide operating flexibility and ensure plant productivities. A summary of major design criteria is presented in Table 1. HIMCO assembled the results of the studies of the various consultants along with internally generated studies to produce the feasibility document. The decision to supply 100% equity by HIMCO rather than arrange project financing help to expedite the project. Cooperation Between HIMCO and Regulatory Agencies With cooperation and mutual trust established between HIMCO and regulatory agencies, the time required for environmental permitting was streamlined as much as practical. To expedite the required construction permits, HIMCO proposed to the USFS that HIMCO fund the total cost of an Environmental Assessment Report (EAR) and that issues be addressed at the technical level of an Environmental Impact Statement (EIS). The previous studies on the critical issues of archaeology and biology provided HIMCO with the information to satisfy the proposed approach. Houston International Minerals and the USFS agreed to have Environmental Research and Technology (ERT) of Fort Collins, CO, prepare a draft EAR for the USFS.

Jan 11, 1983

By Thomas Leonard, Philip R. Berger, Bryan E. Papillon

Bardon Trimount Inc., a large producer of aggregate, crushed stone, and concrete, was experiencing significant public opposition to its five quarries in the Boston area. It was believed by the authors that this opposition could be significantly lessened if the total number of blasts per week were reduced. Although the blasting company at these quarries, Austin Powder Company, contended that this could easily and safely be accomplished by increasing the size of the blasts, regulations precluded this alternative by limiting the total amount of explosives that could be used per blast.

Jan 1, 1996

By Walter R. Curtner

Many, if not most, of today's pollution liability claims are related to events ("occurrences") that happened in the past. This fact creates an opportunity to obtain a large amount of insurance coverage at essentially no cost. Furthermore, in many cases, this insurance coverage is readily available. Scenario #1 For some 15 years, an underground gas tank has had a slow leak. The leak has now been discovered because the gas has contaminated nearby wells. As a result, an expensive $1 million cleanup is required. In addition, a liability suit has been filed for damages due to the contamination of nearby wells. Consequently, legal expenses are being incurred. Are all of these actual and potential costs insured? Obviously, if you have a pollution liability policy in place, the above costs will probably be insured. I say probably because business liability policies are not uniform. But, what if you don't have a pollution liability policy and what if your current general liability policy excludes all pollution liability (as most of them do today)? Under these circumstances, it first appears there is no insurance for this $1 million cleanup and liability suit. But this is probably not the case. You may well have insurance coverage, and you may well have much more insurance coverage than you ever expected. And, the insurance that I'm referring to is already in place. You simply need to find it and learn how to use this insurance - I'm referring to your old policies. In many cases, old liability insurance policies provide coverage for claims made today, because these policies were written on an "occurrence" basis of coverage. In fact, most still are written this way. This means that the insurance policy covers bodily injury or property damage liabilities (as defined in the policy) arising out of' "occurrences" or accidents that happen during the policy period regardless of' when the claim for damages is made. Therefore, for insurance purposes, the key question is: when did the "occurrence" take place? If someone falls and breaks a leg, that is clearly an "occurrence." The broken leg occurrence is, therefore, insured by the liability policy that was in existence at the time of the fall - regardless of when the claim or suit is filed, if ever. However, the answer to this question is seldom an easy one when you are looking at a pollution claim. In our scenario, the tank had a slow leak over 15 years, but property damage was not discovered until now. The question of when the "occurrence" (as defined in the insurance policy) took place has been litigated and continues to be litigated in many courts across the country. But, most often the answer has been that, for insurance purposes, the "occurrence" is the entire period that the tank was leaking (15 years), even though the contamination to the water was not discovered until 1987. This means that the person or company that is insured can potentially use all of its general liability policies (if they are "occurrence" policies, and most were), which were purchased during the 15 years from 1972 until 1987. And, these policies will potentially insure all of the claims and related exposures that arise out of this leaky underground gas tank. Scenario #2 In our first scenario, the claims and expenses were insured by past general liability policies because the claims arose out of events in the past, which, in turn, caused damage. Let's look at another example. In this scenario, Company XYZ has received a request to help clean up a landfill site because 10 years ago, XYZ dumped some toxic substances at the site, which was totally legal at the time. XYZ has not dumped anything at the site since this time. Nevertheless, XYZ is now being required to contribute $2 million to the cleanup of this site. In this scenario, if you had purchased "occurrence" general liability policies 10 years ago, these 1977 policies would (potentially) apply to the current $2 million cleanup claim. And, the reason is that the "occurrence" leading to the 1987 claim took place in 1977.

Jan 10, 1987

By Frank P. Frandina, Michael J. Loehr, Paul E. Gabryszak

The Heartland Corridor Clearance Improvement Project is part of a regional Public-Private initiative to allow double stack container trains a direct route from the Port of Norfolk through Virginia, West Virginia, Eastern Kentucky and into Central Ohio. In the Preliminary Engineering stage, 30 existing tunnels were assessed and 28 were found to need clearance improvements to allow the use of double stack trains. Alternative tunnel enlargement methods were developed to achieve the desired clearance improvements, while maintaining structural integrity and minimizing disruption to train traffic. This paper summarizes the geometric and condition investigations of the existing tunnels, as well as describes the preferred methodologies to achieve the desired clearance. The clearance improvements will be implemented beginning in the summer of 2007.

Jan 1, 2007

Discussion of the paper of Frederick Laist, presented at the Butte meeting, August, 1913, and printed in Bulletin No. 79, July, 1913, pp. 1147 to 1162. J. C. DICK, Salt Lake City, Utah :-I would like to ask Mr. Laist why a 10 per cent. salt solution was used. MR. LAIST :-The reason for using salt in the solution is to get .the sulphur. The solution of dilute sulphuric acid has no solvent action on the sulphur even after roasting, and the addition of the salt is made primarily to dissolve the sulphur chlorides. MR. DICK:-I would like to ask also if you made any experiments as to grinding fine your calcines, rather than leaving the coarse material. MR. LAIST :-We have not made any experiments along those lines except in the laboratory, but the objections which we have to grinding are that the difficulties of roasting are very much greater when roasting finely ground material than when roasting coarse material, and the difficulties of leaching are somewhat increased; the percolating system is simpler and easier to manipulate, particularly when acid solutions are used, so that we prefer from our experience not to grind. STUART CROASDALE,* Denver, Colo. (communication to -the Secretary +) :-In order to meet the conditions involved in his ore-treatment problem, Mr. Laist has developed a very interesting and apparently successful metallurgical hybrid which he calls the oxychloridizing roast. The lower floors of the MacDougall furnaces are made to accomplish what used to be done on the " cooling floor" in the old days of salt roasting and " hypo " or brine leaching of silver ores.

Jan 11, 1913

By Samuel M. Cassidy, John A. Garcia

In some districts of the bituminous coal field the problem of constructing bulkheads to seal off water under pressure is becoming increasingly important. Recently this matter has been brought very much to the front by the loss of a large Illinois mine due to failure of a bulkhead that separated it from several old, flooded mines. As this great misfortune has provoked much inquiry about proper bulkhead design, it is felt that a description of the successful and extensive water-sealing practice at three mines that have different natural conditions will be of considerable interest to those connected with properties having a present or future water problem and to engineers that may have to design safe bulkheads of economical construction. These three mines are the Saxton and Dresser, near Terre Haute, Ind., and the Hegeler, near Danville, Ill. All three have water conditions that make it necessary to regularly seal off all worked-out sections of the mine, and there are considerably over a hundred bulkheads in each. AS far as the writers know, these three mines are the only ones in the bituminous coal fields of the United States with anything like so large a number of water seals and experience, although a number of other mines are known to have a few bulkheads. More detail will be included herein on the Saxton mine than on the others, as the writers are more familiar with it. General Mining System All three of the mines use the same general panel room-and-pillar system, which consists of rooms turned both ways off room entries and a solid block of coal left on all sides of the completed panel except on the cross-entry side, where a heavier pillar is pierced by two entries for haulage and air. On completion of the panel the two entries arc sealed and the panel is then isolated from the rest of the mine. Owing to water conditions, no pillars are pulled; recovery inside the panel barrier pillars is approximately 65 per cent.

Jan 1, 1938

By Frederick N. Rhines, William A. Anderson

The investigations of Wymanl have demonstrated that copper deoxidized with several of the commonly used agents that confer immunily to ordinary hydrogen em-brittlement can still be embrittled if it is annealed alternately under oxidizing and reducing conditions. During the oxidizing cycle, oxygen diffuses into the copper and frequently deposits a subscale composed of the oxide of the residual deoxidizing agent. Upon subsequent reduction with hot hydrogen, the copper becomes ruptured along the grain boundaries to a depth sharply limited by the previous penetration of oxygen as delineated by the inner boundary of the subscale. Obviously the sensitivity to this kind of hydrogen embrittlement is engendered by the introduction of oxygen during the oxidizing anneal, but beyond this the mechanism of the process, and hence the controlling factors, remain obscure. There are several possibilities: (I) oxygen dissolved in the copper matrix of the subscale may, upon cooling prior to the hydrogen anneal, precipitate as cuprous oxide which is subsequently reduced by hydrogen as in the familiar case of hydrogen embrittlement; (2) oxygen in solid solution in copper may itself confer susceptibility to embrittlement by hydrogen; (3) the normally refractory oxides such as those of aluminum, silicon and titanium may themselves be reduced by hydrogen when in contact with copper; or (4) the precipitated oxides of the subscale may be complex compounds such, perhaps, as SiO2.Cu2O, which are partially reduced by hydrogen. These possibilities have been examined, and it has been concluded that the first three and possibly the fourth are operative collectively or individually under more or less predictable conditions. Effect OF Precipitated Cuprous Oxide and Dissolved Oxygen The literature provides no definite proof that oxygen in solid solution in copper can confer susceptibility to hydrogen embrittlement; indeed, the research of Leiter2 seemed to indicate the opposite—that to produce the effect, cuprous oxide must be present in massive form and in a more or less continuous network along the grain boundaries. To test this point, pure copper has been annealed in hydrogen under conditions designed to ensure the presence in various samples of: (I) precipitated cuprous oxide, (2) dissolved oxygen only, and (3) no oxygen in any form. Very pure copper" said to contain no oxygen and no spectro-scopically detectable traces of any other element (that is, no individual detectable impurity in quantity greater than 0.0001 per cent) was used. Strips of this material cold.-rolled 75 per cent to 1/8 in. in thickness were subjected to the following treatments, the results of which are noted:

Jan 1, 1941

By J Boland

Polycrystalline diamond compacts (PDC) have been widely used as cutting elements in the drilling tools for the oil, gas, civil and mining industries because of their faster penetration rates and longer bit life. US Department of Energy reports that PDC bits account for more than one-third of the total footage drilled worldwide (US Department of Energy, 2004). However, non-thermally-stable diamond composites (NTSDC) have seldom been applied to geothermal drilling, since premature failures of such PDC cutters have been observed in hard rock formations. Several factors need to be considered to prevent premature failure of cutters and improve cutting performance when using PDC-based bits and other rock cutting tools. The first set of factors consists of the strength, density, stiffness, toughness and thermal resistance of the PDC and the rock. A second set relates to the complex behaviour of the bonding between the PDC cutter and the bit matrix, or the pick and the pick holder, which is vital in maintaining stable, reliable and durable adhesion of the cutters to their hubs. Finally, based on a better understanding of the cutting processes, the formulation of a predictive model would assist in further development of cutter design.

Jan 1, 2004

The moisture content of clean coal contributes significantly to the product's transportation costs, handleability characteristics and/or energy value. A major contributor to the total moisture is the ever increasing proportion of fine coal in

Jan 1, 1994

By D. H. Steve Zou, Cui Lin

"This paper first discusses the basic attributes of sustainable mining and the responsibilities of various steak holders including mining companies, governments, and engineers. It is followed by a brief overview of the current practice on regulations, inspections, waste management and mine closure planning in Canadian mining industry. A case study is then presented as an example of sustainable mining where mine planning, mineral recovery, environment protection, reclamation and community development were integral parts of the overall strategy. A comparison of the mine site before and after mining is made to demonstrate the ""best practice"" in modern mining.Sustainability in Mineral Resource Development Extraction of mineral resources and other natural resources on the Earth has been and will continue to be an essential activity necessary to support human’s life. We live on the planet and depend on the available resources to survive. The extracted materials form the base to support modern life. However, we must be aware of the fact that mineral resources are limited on the Earth and may not last forever. Every time we extract one ton of materials, there is one ton less. They are not able to regenerate or regrow. One can ask a simple question: How long will they last? Or, is there anything left for our great grandchildren and many generations to come? The answer is not simple. Some minerals have become scarce or about to deplete. Some minerals may last longer. The reserve of a type of minerals depends on what we have discovered and the minable amount depends on accessibility and technology we have. Even if there are minerals in the deep ground, we may be limited by our technological capability. At the same time, we also need to understand the action of mineral extraction from the ground and the consequences of that action. Mineral extraction is a very hard work. We must break the ground to extract the ore, either through surface mining or underground mining. This action means disturbance of the land where we live. The disturbance is much more visible in surface mining than underground mining. The disturbed land, if not properly reclaimed after mining, is not going to be reusable. The very purpose of extracting minerals from the ground is to support our life but the action has a negative impact on our life. How can we reduce and limit disturbance of land from the action of minerals extraction? How can we make the disturbed land reusable? These issues must be properly addressed and a balance achieved."

Jan 1, 2017

By N. Katsikaros, N. S. ‘ Yap, B. Adaszynski

"Cyanide is a well proven, effective lixiviant that has been utilised for centuries in gold extraction processes. Despite being used in close to 90% of gold processing plants, cyanide leaching is still being scrutinised due to its toxic nature. With governments tightening the regulations on cyanide management, and recently erected sites situated closer to community and environment, leach waste and tailings treatment has become increasingly important. Gekko Systems has worked with engineering companies and directly with gold producers to provide technical services and supply complete modular cyanide destruction (detox) systems for plants leaching both run-of-mine ore and high sulphide gravity and flotation concentrates. Although similar in principle, the different materials presented unique challenges in design and implementation. Similar to designing any section of a processing plant, the development of the cyanide destruction plant design began with laboratory test work to simulate the full scale operation. This paper focusses on the laboratory test work and how other critical factors such as geographical location, logistics, and local community play a role in the process design and construction. Two design and supply cases are discussed in this paper; one treating intensive cyanidation concentrate leach tails and one treating whole ore CIL tails. Although these plants both use the SO2/O2 process, each presented different challenges in laboratory testing and plant design, resulting in variations in final implementation including reagent choice, oxygen supply, and process control.INTRODUCTIONSince 1887, cyanide has played a large part in the beneficiation of gold from gold bearing ores. Cyanide is used to solubilise gold into solution, and is typically added in excess to maintain the leaching process. Some or all the excess cyanide can often be recovered and reused in the process however chemical destruction of cyanide is often necessary to manage cyanide levels in the tailings storage facility (TSF)."

Jan 1, 2016

By Damien Bretall, William Fourney

Due to the changing face of warfare there is an ever growing need to protect the underside of combat vehicles from mine blasts. This paper presents a new method to better characterize the pressure profiles experienced by a plate as the blast develops. The explosive deformation of a small-scale plate was recorded using synchronized high-speed digital cameras, and then analyzed using 3D Digital Image Correlation software. Time-varying pressure profiles were input into an axisymmetric FEM simulation by fitting curves to data obtained from tests using Kolsky bars to measure pressures. These were then modified to find possible profiles that produce the measured deformations. It was discovered that the final deformation cannot be determined from only total impulse or peak pressures, and that it is very sensitive to the time and spatial decay of the pressures.

Jan 1, 2009

Comparatively recent Tasmanian legisla tion established a series of rigid control standards for environmental protection just as ma spectacular expansion of the mining industry was nearing completion. Upgrading existing protection to obtain the necessary licence to operate under these new regulations required further major works and involved a considerable outlay of non- productive capital at a time when escalating costs and falling metal prices were straining economic efficiencies to the limit. Late in 1974 a major environmental protection scheme was commissioned by the Electrolytic Zinc Company of Australasia Limited at Rosebery on the West Coast of Tasmania. This 4 million dollar project was specifically developed by the Company ahead of and to meet the new standards for control of total effluents discharged from its zinc-lead -copper-pyrites mine and concentrator.

Jan 1, 1977

By Nicol SK, Engel MD

Ion flotation involves the adsorption of ionic species, in association with surfactant molecules, at the surface of rising gas bubbles, for the purpose of recovering and concentrating those ions. The objective of this study was to optimise the ion flotation process using a heap-leach liquor, containing gold cyanide, and the surfactant cetyl trimethyl ammonium bromide (CTAB). The aim was to minimise the surfactant reagent dose, maximise the throughput of feed liquor in the process, and satisfy the dual constraints of a high gold recovery and a high volume reduction factor. Development of a first order model of the ion flotation process formed the theoretical basis for the test program procedure and the interpretation of the results. Batch tests were used in order to determine the ultimate recovery curve for the heap leach liquor-CTAB surfactant system. The results indicated that a surfactant dose of about 0.083 g/l would be necessary in order to achieve a satisfactory gold recovery. Continuous tests were then performed on a small-scale pilot plant at the Newcastle Laboratories. The optimum result achieved was a gold recovery of 85 per cent, a volume reduction factor of ten, and a feed throughput of 2.3 m3/m2-h. Recent work also indicates that very much higher volume reductions can be achieved using a larger diameter vessel. The improvement may be a consequence of a reduction in wall effects and hence an improvement in foam drainage.

Jan 1, 1993

By G. C. Naveen

Punatsangchu Hydroelectric Project Authority is constructing 1020 MW underground hydroelectric project in Bhutan. The project envisages construction of concrete dam, Desilting Chamber, Head Race Tunnel, Power House Complex and Tail Race Tunnel. Tunneling is one of the major activity in any underground projects as they are driven for multiple activities. By and large the tunnels are a major part of connecting networks from surface to caverns/underground working sites. Many tunnels in hydropower project are part of water conducting systems and one such important tunnel is the Tail Race Tunnel in this project and had to be excavated in thinly foliated rockmass conditions by D&B method. The rockmass is traversed by three to four joint sets and few minor shear seams. Rock Class “Q” values were between III and IV. Tunnel was excavated by full face parallel hole drilling blasting method. The adopted blasting method consisted of drilling 45mm (1.77 inch) diameter holes to a depth of 2m and the drilled holes were charged with 40mm (1.57 inch) diameter cartridge explosives and charges were initiated with half second non electric initiators. The perimeter holes were drilled at closer spacing of 30cm (1 feet) and alternate holes were charged using 32mm (1.23 inch) diameter cartridges explosive. Low dipping foliation joints present in the rockmass tend to slab in crown portion and erratic occurrence of intrusive bodies lead to unpredictable behavior of rock mass posing a major challenge for the safe excavation. Stability was a major issue through controlled blasting under constant supervision too could not limit the overbreak in certain weak rockmass conditions thereby exposing cavities of about 2.5m (8.2 feet). The stabilization of these cavities and handling the overbreak due to rockmass condition was time consuming and warranted additional supports. With systematic measurements and controlled blast designs the Horse Shoe Shaped Tail Race Tunnel of 9.1 m (29.85 feet) diameter and 304m (997.37 feet) length to connect with Downstream Surge Gallery of 314m (1030 feet) length, 18m (59 feet) wide and 58.8m (193 feet) height in thinly foliated and jointed biotite gneiss rockmass was successfully excavated.

By Louis Gariepy

El presente trabajo describe las características geológicas actualizadas de Cerro Lindo como yacimiento del tipo de sulfuros masivos volcanogénicos (SMV) y propone un modelo genético de su formación que apunta a una deposición en parte -sobre el fondo marino y por debajo de él-, controlada por fallas sinvolcánicas dentro de un graben intra-cuenca volcánico-sedimentaria.

Apr 22, 2003

By Taylor G. H

The proposed classification scheme is based on two primary parameters, one for petrographic composition and the other for rank, both being determined with microscopical techniques. The scheme has been applied to a wide range of Australian coals and found to provide a useful means of relat- ing their inherent properties to properties such as volatile- matter yield, crucible swelling number, and calorific value, which will determine how these coals might be used coimierciallyti,

Jan 1, 1969