Search Documents

By J. Philip Neal

Feldspar is no example of special mineralization in isolated spots: it can usually be found within a mile or so of almost anywhere. Along with silica sand, it is a major part of our world's total mineral composition. This fact imparts to it an economic status different from a sulfide ore, or potash, or phosphate. While every feldspathic "stringer" does not possess economic potential, the generous distribution does yield a high statistical frequency of good feldspar ore bodies: the adjective "good" being subject to some flexibility of interpretation. The strong chemical bonds of this alkali aluminum silicate give it certain use advantages, but under present technology its individual elements cannot practically be separated to create aluminum, potassium, sodium, silicon - or their oxides. Its present uses rely upon chemical inertness - as in fillers; and on its physical melting characteristics and their effect in glass, enamel, or ceramics.

Jan 1, 1973

By Oliver C. Ralston, and others

"INTRODUCTION Investigations of the Nonmetals Division are now conducted at College Park, Md.; Tuscaloosa. Ala.; Seattle, Wash.; and. Norris, Tenn. The last of these was acquired, this year by arrangement with the Tennessee Valley Authority and is engaged in electrothermel research, using power generated by the T.V.A. and. raw materials from that region. In general, the work of the division is concerned with dressing nonmetallic minerals end utilizing the products there-from. Coal, salts, and waters are investigated, and the suitability of apparatus and equipment is studied.As the Metallurgical. Division of the Bureau of Mines makes routine tests of certain nonmetallic ores under prescribed conditions for the public if they are of general interest, the published reports of that division should be read and thus, with the reports of tile Nonmetals Division, the whole field may be covered."

Oct 1, 1939

By W. L. Dumoulin

A RATHER detailed description of the entire plant and leaching process was given in a paper recently presented to the Institute,1 so this paper will cover briefly only the crushing practice of the New Cornelia Copper Co. for the year, 1918. The ore, which is mined by steam shovels and loaded in side-dump cars, passes through two crushing plants. These crushing plants were constructed to crush the ore required by a leaching plant of 5000 tons daily, capacity, during a crushing period of 16 hours. The primary plant reduces to less than 3 in. (76 mm.) and the secondary plant, to ¼ in. (6.35 mm.), which is sufficiently fine for satisfactory percolation of solution through the ore in the leaching tanks, and to give good extraction. The ore is then conveyed to the leaching tanks by a system of 28-in.. (71-cm.) belt conveyors. On the way to the leaching tanks, it passes through an automatic sampling plant, where a 1-per cent. sample is taken. From the primary crushing plant, the ore is conveyed by two 36-in. (91-cm.) belt conveyors to a 10,000-ton steel storage bin, with a reinforced-concrete flat bottom. The ore discharges from the bottom of this bin onto four 20-in. belt conveyors, which deliver it to the four units of crushers in the secondary crushing plant. There is no storage bin between the mine and the primary crushing plant. The ore breaks very coarse, is very hard, and contains a great many boulders, some as large as 4 ½ by 4 1/2 by 10 ft. (1.3 by 1.3 by 3 m.). Jams form in the bowl of the coarse crusher in the primary crushing plant, as a consequence, and are freed by means of an immense steel hook operated from a 40-ton electric traveling crane.

Jan 8, 1919

By B. Boberg

Annual requirements of uranium to fuel the 441 currently operating nuclear reactors in the world is 170 million pounds U3O8 (65,385 tonnes U). 2005 global production was 108 million pounds (41,595 t U), of which only 2.7 million pounds U3O8 (1,039 t U), was produced from US uranium deposits. US nuclear utilities represent 26% of the global nuclear capacity but only obtain 2.5% of their supply from US uranium mines. Since 2002 annual global production increased from 93 million pounds U3O8, a 15% increase and the US production increased from 2.3 million pounds to 2.7 million pounds, a 17% increase. Reasonably Assured Resources (RAR) of 12,332 million pounds U3O8 (4.7 million t U) are reported from a wide variety of countries and types of uranium deposits. This RAR suggests that there are significant global uranium resources potentially producible at a price of $50 per pound U3O8 ($130 per kg U). Table 1 shows the distribution of global uranium resources. This table, prepared from historic data maintained by the World Nuclear Association, does not include some areas of the world that are currently considered to contain significant resources of uranium such as Mongolia. Table 1 suggests that the United States contains the fourth largest uranium resource in the world with 890 million pounds U3O8, behind Australia, Kazakhstan and Canada in resources that are producible at a price of $50 per pound U3O8 ($130 per kg U). Within the US, the states that demonstrate the greatest amount of uranium resource are Wyoming, New Mexico, Texas and the Four Corners Area of Arizona, Colorado and Utah.

Jan 1, 2007

By Rafael C. Castro, John Overton, Gregg Sherry, David A. Sutter

This paper presents an innovative ground support solution developed to construct a tunnel cross-passage for the MUNI Metro Turnback (MMT) Project. A “soft center” jet grouting approach was designed to provide solid ground support while maintaining a soft center to allow for hand-mining of a 2.44 m (8 ft.) wide, 3.66 m (12 ft.) tall and 4.6 m (15 ft.) long cross-passage through soft Bay Mud. Prohibitive costs and schedule impacts associated with mining under compressed air (at the time being used for main tunnel construction) were the catalysts to search for alternative methods for cross-passage construction. Limited surface disruption, relatively low costs, ease of subsequent excavation, nominal schedule impacts and proven local success of jet grouting were key factors in selecting and designing this method of ground support.

Jan 1, 1997

By H. S. Auvil

[The shrinkage of coke after formation is one of the variables that affects the net expansion of the change in both industrial and test ovens. Various test results have been interpreted as indicating that cokes from certain coals shrink to a marked extent and that other cokes show very little shrinkage; out no comprehensive experimental study of the shrinkage of coke after its formation and of the factors influencing this shrinkage has come to the attention of the authors. While investigating the reactivity of cokes made by the BM-AGA method,6/ Reynolds7/ found that granular low-temperature cokes shrink considerably then reheated to higher temperatures. This shrinkage was large enough to influence the behavior of the charge (net expansion or contraction) in a coke oven to a marked extent. Since that time the Bureau of nines has investigated the shrinkage of coke different methods, all of thick had one common objective - the elimination of the effect of other factors, such as swelling in the plastic range, which could either partly or completely mask the shrinkage of the coke. Only parts of these studies have been published8/9/ in abbreviated form in]

Jan 1, 1940

By H. Nan

Using the case of Qianqiu Mine, Yima Coal Mining Administration, theoretical analysis, laboratory physical simulation, and underground observation were performed to study the major parameters for fully mechanized sublevel caving mining method, including drawing spacing, drawing sequence, drawing numbers, and number of shields performing simultaneous drawing. The effects of those parameters on coal recovery and amount of waste rocks were also investigated. The optimal coal drawing technology for this case was obtained.

Jan 1, 2006

By N. Kumar Kittusamy

The purpose of this study was to assess the adequacy of the cab design and to determine the percentage of musculoskeletal symptoms among workers. A questionnaire was designed to assess demographics, work information, job history, and musculoskeletal symptoms in operators of heavy construction equipment. Information concerning equipment included design of the seat/chair, levers, pedals, bothersome vibration, quality of egress from the equipment, proper preventative maintenance and repairs, and age of the equipment. The body regions that were evaluated included the neck, middle/upper back, low-back, shoulder/upper-arm, elbow/forearm, wrist/hand, hip, knee, and ankle/foot. One hundred and eighty nine operators completed the questionnaire. The results indicate that these workers are at risk for developing musculoskeletal disorders, the need to perform a larger survey to further substantiate the outcome, and the need to quantify risk factors (i.e., whole-body vibration and static sitting postures).

Jan 1, 2003

By C. J. Hall

I would like to congratulate Professor Gershon on an idea that is obviously valuable and is certainly new to me. It has, however, to be further developed, in that one can get fallacious results by limiting oneself to positional weights. In the example problem, the positional weight of one block was 8.6 (the 8.0 value in the paper was incorrect) for 36 units in the cone, for a mean block value of 0.239. The positional weight of the second block was 4.4 for 15 units, for a mean block value of 0.293. Surely one would expect the second block to be rated higher. Additionally, the time value of money adjustment cannot be determined by depth, because the time that a block is mined is determined by the mining sequence, not depth. Figure 1 shows a slightly altered version of Professor Gershon's pit. The overall value of the pit is the same, as are the total values under each of his blocks. The values in the right-hand cone have been reversed top to bottom, and the values in the rest of the pit adjusted to keep the central cone total unchanged. All values have been multiplied by 10. Figure 2 shows the sequence of mining, at three blocks per year, for Professor Gershon's pit, and Fig. 3, the sequence for a pit under the other block. Table 1 shows the value and discounted value (15%) of Professor Gershon's pit, and Table 2 shows similar values for the second pit. It is apparent that the second pit schedule is more valuable than the first.

Jan 1, 1988

By J. E. Conley

Available statistics show that the demands of the American chemical industry for sodium sulphate have been increasing slightly in recent years. The supply from domestic sources, particularly In the form of byproduct salt cake from the acid manufacturers, has been tending to decrease due to the growing manufacture of synthetic acid. Both hydrochloric and nitric acids are being synthesized from their elements. The natural result has been that a smaller amount of salt cake is available. Simultaneously, the expansion of the Kraft paper industry, especially in the South, has brought about greater demand for sodium sulphate in that section. This dean is being met by domestic byproduct salt cake, by imported German sodium sulphate made from potash waste liquors, and by favorable situated domestic deposits of Glauber salts and tile anhydrous salt, thenardite. No shortage of natural sodium sulphate exists in the United States, but usually such deposits occur in semiarid regions far removed from transportation facilities and from markets. Moreover, the major portion of the natural deposits is Glauber salt or mirabilite (Na2SO4 ? 10H20), which must be dried or dehydrated in order to meet consumer requirements. The water of hydration represents, roughly, 55 percent of tae total weight of the crude salts and therefore has a very important influence on transportation costs. In marry instances the cost of getting, even the dehydrated product to market is the deciding economic factor. Therefore, the recovery oil production of anhydrous sodium sulphate from plant-.waste liquors or from natural brines of suitable composition might be economically feasible. The U.S. Bureau of Mines, at its nonmetallic Minerals Experiment Station, New Brunswick, N. J., has, for a number of rears, been investigating the commercial possibilities of treating the complex saline mineral polyhalite (K2SO4?NgSO4?2CaSO4?2H20) for the recovery of potash and magnesia. Certain proposed processes (1, 2, 3, 4)4/ yield waste liquors that contain the bulk of the magnesium and sulphate originally combined as magnesium sulphate in the polyhalite molecule. Sodium chloride In limited concentrations is also present, as extensive beds of salt occur in strata overlying the polyhalite deposits. A typical waste liquor would contain:

Jan 1, 1936

By R. V. Higgins, G. B. Shea

"FOREWORDIn the second year of World War II, the petroleum industry in California was taxed to near capacity to satisfy the expanded war demand for petroleum products, particularly fuel oil. With discoveries of crude oil in California declining and known reserves being depleted rapidly, conditions appeared to warrant study of the possibilities of utilizing the outcropping bituminous sandstone deposits in California for obtaining new sources of oil if the war should he prolonged. At conferences in Washington, D. C., with members of the Petroleum Administration for War and the Geological Survey, Bureau of Mines engineers emphasized the importance of determining the extent of those outcropping deposits of oil-impregnated rocks and of developing a practical process for commercial recovery of the contained bitumen to assure, if necessary, a supplementary supply of fuels. The desirability of such a study was recognized, and in July 1943 the Petroleum Field Office of the Bureau of Mines at San Francisco, Calif., in cooperation with the Geological Survey and the Petroleum Administration for War, initiated a study of the bituminouss sandstone problem. It was agreed that all mapping and geological work in connection with the study would be done by the Geological Survey, all engineering studies in developing a process for extracting the oil would be carried out, by the Bureau of Mines, and that the Petroleum Administration for War would aid in final adoption of the results in the field if circumstances warranted such action.Deposits of bituminous sandstones in California occur principally in the immediate region of the Coast Range mountains, notably at Pt. Arena, in Mendocino County, about 110 miles north of San Francisco; near Santa Cruz, in Santa Cruz County; in the Edna area in San Luis Obispo County; in the Sisquoc area in Santa Barbara County; and in the Ojai and Santa Clara Valleys in Ventura County. 4/ In addition oil-bearing sands outcrop near McKittrick and Maricopa, in western Kern County, and along the east edge of the Kern River oil field. Among the several prominent deposits of these source materials, those occurring near the cities of Santa Cruz and San Luis Obispo, and the town of Sisquoc are the largess."

Oct 1, 1948

Isometric strength is defined as the capacity to produce force or torque with a voluntary isometric (muscle[s] maintain[s] a constant length) contraction. The key thing to understand about this type of contraction and strength measurement is that no body movement occurs during the measurement period. The tested person's body angles and posture remain the same throughout the test. Isometric strength has historically been the type most studied and measured. It is probably the easiest to measure and to understand. Some strength researchers feel that isometric strength data may be difficult to apply to some "real life" situations because in most real circumstances people are moving - they are not static. Other researchers counter that it is equally difficult to determine the speed of movement of a person or group of persons doing a job (each moves in his or her unique manner and speed across the links and joints of the body). Thus, dynamic strength test data collected on persons moving at a different speed and/or in a different posture from the "real world" condition will be just as hard to apply. In truth, neither is better - they are different measurements. Both researchers and users should collect and use data that they understand and that fits their application. Workplace Assessment When a worker is called on to perform a physically demanding lifting task, the external load produces moments - tendencies to produce motion, also called torques - about various joints of the body.(1) Often these moments are augmented by the force of gravity acting on the mass of various body segments. For example, in a biceps curl exercise, the moment produced by the forearm flexors must counteract the moment of the weight held in the hands as well as the moment caused by gravity acting on the forearm's center of mass. To perform the task successfully, the muscles responsible for moving the joint must develop a greater moment than the combined moments of the external load and body segment. It should be clear that, at each joint of the body, there is a limit to the strength that the muscle can produce to move ever-increasing external loads. This concept forms the basis of isometric muscle strength prediction modeling.(1) The following procedures are generally used with this biomechanical analysis technique. First, workers are observed (and usually photographed or video-taped) as they perform physically demanding tasks. For each task the posture of the torso and the extremities are documented at the time of peak exertion. The postures are then re-created using a computerized software package, which calculates the load moments produced at various joints of the body as the task is performed. The values obtained during this analysis are then compared to population norms for isometric strength obtained from a population of industrial workers. In this manner, the model estimates the proportion of the population

Jan 1, 1998

By R. Patterson

Tracer gases have been utilized successfully in a variety of industries, each with specific releasing and sampling methods. The various attributes of tracer gases are dependent on the industry the tracers are utilized in. Tracers must be chemically and thermally stable, safe, odorless, detectable at low concentrations, have a low background concentration, and should not be naturally occurring in the environment if they are utilized in underground mining applications (Thimons et al., 1974). In addition, the tracer gas should be inexpensive, non-corrosive, non-toxic, easily transportable, readily attainable, and non-radioactive (Kennedy et al., 1987). Sulfur hexafluoride (SF6) met many of these above requirements and therefore was introduced as an ideal tracer gas to use in mining industry in the early 1970?s (Thimons et al., 1974). Due to the nature of underground mining including complicated geometry, irregular flows, turbulent flows, obstructed airways, and leakages it is difficult to use conventional anemometer and smoke tube techniques to accurately measure the effectiveness of ventilation controls (Thimons et al., 1974; Klinowski and Kennedy, 1991). There have been several applications of SF6 as a tracer gas in underground metal/non-metal and coal mines. Thimons et al. conducted early testing of SF6 in an underground limestone mine and determined that it is an effective technique for evaluating auxiliary fans, estimating volumetric flow rates in large areas, and measuring low flow velocities. A rapid face ventilation measurement method (FVM) utilizing SF6 was developed by the Bureau of Mines to make face measurements in underground coal mines (Timko and Thimons, 1982). When measuring the effectiveness of jet fans in dead headings SF6 was proven more effective than smoke tubes (Timko and Thimons, 1982). Experiments related to determining methane liberation in the gob were also conducted by injecting SF6 into a borehole (Timko and Thimons, 1982). Also, in an emergency situation where the gob had to be sealed due to a fire, SF6 was released to determine the effectiveness of the seals (Timko and Thimons, 1982).

Jan 1, 2011

By R. W. Smith, D. L. Taylor, K. A. Altman

The importance of metallurgical information in reaching appropriate decisions during the development of mining projects is demonstrated. A financial analysis is calculated using a simulation that includes random number generators. The results are compared to the results of a traditional sensitivity analysis. The traditional analysis is shown to have the potential to overestimate the value of mining projects. The type of statistical distribution selected for the random number generator affects the results significantly. The statistical method of analysis provides insight into the amount of metallurgical testing to be completed and verification of how representative the samples are.

Jan 1, 2000

By R. A. Egen

The purpose of this book is to provide an indication of what good hoisting practice is and how it might be achieved. To this end the book contains discussions of equipment and inspection and maintenance procedures developed and used by mining people in striving for safe, reliable hoisting equipment. Most of this information comes from domestic practice; the rest is foreign, notably from Canada. Most things discussed have long proved their general worth, and others promise to; a few are beginnings. However, nothing is conjectural or theoretical; the practices described herein are in use somewhere in the mining world. The stress is on equipment in use; it is not a design-guidelines manual. Nevertheless, there are some sections dealing with design material since it may be of value in a maintenance/ replacement sense. Mine hoisting installations encompass such a wide variety of equipment and conditions that it is impractical to specifically cover them all. This book mainly treats conventional systems using conventional components with some discussion of the more common unconventional (special) systems in use. There is no recognized definition for a "conventional" mine-hoisting system. Herein the term means those systems most commonly used in daily operations for transporting men, materials, and product-electrically driven drum and friction hoists, with guided conveyances running in vertical or inclined shafts. Beyond this, what "conventional" means is probably best illustrated by the topics discussed.

Jan 1, 1975

By A. W. Cramb

A three-day symposium on the production of clean steel organized by The South African Institute of Mining and Metallurgy, was held in September 1995 at Vanderbijlpark. It was attended by 151 delegates, who represented the whole of the steel industry in South Africa: Iscor Works, Saldanha Steel, Columbus Stainless, Highveld Steel & Vanadium, Iscor Research & Development, University of Pretoria, and Technikon Witwatersrand, as well as the users of steel products were represented. Professor Allan Cramb held the delegates attention with well-presented research and practical information. He obtained excellent interaction with the delegates by responding in depth to the questions put to him during the Symposium. In summary, he emphasized the following aspects of the elimination of defects during the processing of steel in continuously cast materials.

Jan 1, 1996

By Catharine E. G. Farrow, David H. Watkinson

The Ni-rich Epidote Zone of the Fraser Mine at Sudbury is characterized by alteration assemblages rich in epidote, actinolite and magnetite which are roughly concentrically zoned and up to hundreds of meters in length. These zones form discrete areas within the igneous Footwall Breccia below the Sudbury Igneous Complex. The assemblages grade from epidotized Footwall Breccia matrix,through actinolite-bearing rocks with few vestiges of original Footwall Breccia textures, into the most intensely altered rock, a magnetite-rich facies. Pentlandite, pyrrhotite and pyrite are the dominant sulfdeminerals; chalcopyrite is minor. The strongest geochemical differences compared to original Footwall Breccia occur where epidote and actinolite dominate the alteration assemblage (EPDZact facies). The most intense alteration facies are typifed by low Cu/(Cu+Ni) values of <0.1. Strong positive correlations exist between Ni and Co, Cu and Au, and among Ir, Os, Ru and Rh. Chondrite-normalized Ni - PGE -Au - Cu plots display an overall increase in all elements from the least to the most intensely altered facies except for Au and Cu. As the proportion of actinolite increases in the EPDZact facies, the chondrite-normalized profles fatten considerably due to low Au and Cu contents. Abundances of Ni, Ir, Ru and Rhalmost ubiquitously increase with degree of alteration. In contrast, Cu, Zn, Ag and Au contents are low in almost all facies. It is suggested that saline hydrothermal fluids moved through the Epidote Zone formation and became more oxidized as they reacted with the Footwall Breccia and with footwall units, including ultramafic rocks. As this trend continued, magnetite-rich zones eventually developed. The occurrence of calcite locally in these magnetite-rich zones suggests that the pH of the fluid increased, causing Cu solubility to drop as activity in the hydrothermal system waned. Sudden changes in fluid composition such as this may have been due to an influx of fluid from bounding ultramafic rocks. Hydrothermal activity was focused along the margins of footwall ultramafic units. Individual hydrother-mal cells may have formed in the Footwall Breccia along pre-existing structures or sulfde concentrations. Metals may have been scavenged from sulfide-bearing Footwall Breccia and possibly Sublayer rocks. Nickel and some PGE were deposited in the Epidote Zone, whereas Cu, Au and Ag continued out-ward into the footwall where they were deposited as Cu-rich footwall veins. Copyright © 1996 Canadian Institute of Mining, Metallurgy and Petroleum.

Jan 1, 1996

By Catharine E. G. Farrow, David H. Watkinson

Abstract-The Ni-rich Epidote Zone of the Fraser Mine at Sudbury is characterized by alteration assemblages rich in epidote, actinolite and magnetite which are roughly concentrically zoned and up to hundreds of meters in length. These zones form discrete areas within the igneous Footwall Breccia below the Sudbury Igneous Complex. The assemblages grade from epidotized Footwall Breccia matrix, through actinolite-bearing rocks with few vestiges of original Footwall Breccia textures, into the most intensely altered rock, a magnetite-rich facies. Pentlandite, pyrrhotite and pyrite are the dominant sulfide minerals; chalcopyrite is minor. The strongest geochemical differences compared to original Footwall Breccia occur where epidote and actinolite dominate the alteration assemblage (EPDZact facies). The most intense alteration facies are typified by low Cu/(Cu+Ni) values of <0.1. Strong positive correlations exist between Ni and Co, Cu and Au, and among Ir, Os, Ru and Rh. Chondrite-normalized Ni - PGE - Au - Cu plots display an overall increase in all elements from the least to the most intensely altered facies except for Au and Cu. As the proportion of actinolite increases in the EPDZact facies, the chondrite-normalized profiles flatten considerably due to low Au and Cu contents. Abundances of Ni, Ir, Ru and Rh almost ubiquitously increase with degree of alteration. In contrast, Cu, Zn, Ag and Au contents are low in almost all facies. It is suggested that saline hydrothermal fluids moved through the Epidote Zone formation and became more oxidized as they reacted with the Footwall Breccia and with footwall units, including ultramafic rocks. As this trend continued, magnetite-rich zones eventually developed. The occurrence of calcite locally in these magnetite-rich zones suggests that the pH of the fluid increased, causing Cu solubility to drop as activity in the hydrothermal system waned. Sudden changes in fluid composition such as this may have been due to an influx of fluid from bounding ultramafic rocks. Hydrothermal activity was focused along the margins of footwall ultramafic units. Individual hydrothermal cells may have formed in the Footwall Breccia along pre-existing structures or sulfide concentrations. Metals may have been scavenged from sulfide-bearing Footwall Breccia and possibly Sublayer rocks. Nickel and some PGE were deposited in the Epidote Zone, whereas Cu, Au and Ag continued outward into the footwall where they were deposited as Cu-rich footwall veins.

Jan 1, 1996

By S G. Hagemann, M E. Barley

The Mt Tom Price deposit is a world-class high-grade hematite deposit in the Hamersley Province of Western Australia with an original resource of 900 Mt of almost pure hematite, averaging 63.9 wt per cent Fe. Petrological and geochemical studies at both the Southern Ridge and the North deposit at Mt Tom Price have identified three hypogene alteration zones between unmineralised BIF and high-grade iron ore: distal magnetite-siderite-stilpnomelane; intermediate hematite-magnetite-ankerite-talc-chlorite; and proximal martite-microplaty hematite-magnetite-apatite alteration zones.Fluid inclusions trapped in siderite within the distal magnetite-siderite- stilpnomelane alteration zone at the North deposit revealed primary high salinity (25.5 eq wt per cent NaCl-CaCl2) inclusions that homogenised between 107¦ and 142¦C into liquid. Fluid inclusions trapped in ankerite within ankerite-microplaty hematite veins in the intermediate hematite-ankerite-magnetite-talc-chlorite alteration zone at the North deposit revealed mostly H2O-CaCl2 pseudosecondary and secondary inclusions with salinities of 22.4 - 25.4 eq wt per cent and 22.9 - 25.9 eq wt per cent CaCl2, respectively. Pseudosecondary inclusions homogenised between 153¦ and 449¦C and secondary inclusions homogenised between 103¦ and 157¦C. Fluid inclusions trapped in apatite within talc-microplaty hematite veins in the intermediate hematite-magnetite-talc-chlorite-apatite alteration zone at Southern Ridge revealed that primary, medium salinity (7.0 - 9.0 eq wt per cent NaCl) inclusions homogenised between 181¦ and 257¦C and primary high salinity (22.8 - 25.9 eq wt per cent CaCl2) fluid inclusions homogenised between 118¦ and 257¦C into liquid. Microthermometric analysis of quartz from quartz-hematite veins from the Southern Batter Fault, Southern Ridge show a complex fluid inclusion history. Primary fluid inclusions consist of: low- and high-salinity H2O-NaCI inclusions trapped at temperatures of approximately 140¦ to 230¦C; vapour-rich inclusions of unknown compositions; and æcomplexÆ salt-rich (Ca, Mg, K and Na inclusions).Secondary inclusions consist of medium-salinity fluid inclusions trapped at temperatures of about 140¦ to 280¦C.A two-stage hydrothermal model is proposed for the formation of both the Southern Ridge and North deposits. Early 1a hypogene alteration involved the release of hydrothermal NaCl-CaCl2-rich (25.5 eq wt per cent) basinal brines (110¦ - 150¦C) from the underlying Wittenoom Formation and directed upward along normal faults and focused within the silica-rich rocks of the Dales Gorge Member, by the shales of the underlying Mt McRae Shale Member and overlying Whaleback Formation. Within the Dales Gorge Member hydrothermal basinal brines migrated laterally within large-scale folds with permeability controlled by shale bands and the NW trending dolerite dyke sets. Fluid rock reactions transformed unmineralised BIF to magnetite-siderite-iron silicate BIF, with subsequent desilification of the chert bands. Stage 1b hypogene involved an increase in temperature of the hydrothermal, CaCl2-rich saline (24 eq wt per cent) basinal brines (250¦ - 300¦C) resulting in formation of hematite-ankerite-magnetite-talc-chlorite alteration and the crystallisation of microplaty hematite. Late stage 1c hypogene alteration involved the interaction of low-temperature (~120¦C) basinal brines with the hematite-ankerite-magnetite mineral assemblage. At the Southern Ridge deposit this process was very intense (ie high fluid flux), therefore resulting in the almost total removal of ankerite and resulting in the increased porosity of the ore. Stage 2 supergene enrichment in the Tertiary resulted in the removal of residual ankerite and apatite and the weathering of the shale bands to clay.

Jan 1, 2005

By J. Kalejta

Ever increasing depth of mineral extraction presents a challenging environment for hard rock underground mines. High in-situ stresses and associated seismicity with potential rockburst hazards are the major decisive factors contributing to the choice of a ground support regime. Conventional ground support systems, designed primarily for static loads, are not always capable of providing safe working conditions for underground personnel in seismically active mines. Systems specifically developed to resist dynamic loading and allowing for larger deformations are therefore preferred alternatives. High-tensile chain-link mesh has a proven record of successful use in open cut operations in various rockfall barrier installations due to its high energy absorption capacity. It has also been used in underground operations in various parts of the world. This paper describes a method of mechanized installation of a chain-link mesh evaluated at the Kiruna mine in Sweden and South Deep Mine in South Africa. A purpose-built mechanized roll mesh handler was used in this evaluation. The handler is compatible with all standard multi-boom underground drill rigs and is operated utilizing the hydraulic circuit normally used for the feed arrangement. A number of key performance indicators have been identified as success criteria: ??A 30-50% faster installation compared to the conventional methodology ??The mesh should sustain any blast damage when applied to the blasting face ??No unraveling of the mesh when cut ??No failure of mesh under normal conditions Although the energy-absorbing mesh combined with yielding rock bolts is a ground support system of choice for rockburst prone conditions, the operational upsides recognized during the evaluation imply that this product can also be competitively used in less demanding ground conditions where customarily weld mesh or shotcrete are used as a primary surface support. The main conclusion: a fast, safe and fully mechanized installation.

Aug 1, 2013