Search Documents

By Edo Engel

Blast furnace No. 3 at Zaporizhstal in Zaporozhye is rebuilt in 2016-2017. The Ukrainian company is targeting increased production and availability, mainly through the use of new technology. Zaporizhstal awarded a contract for a new Top Charging Unit to Danieli Corus, after comparing all available technologies. Reliability of the chosen charging device is pivotal, since long outages may be required for maintenance/replacement jobs, which strongly affects the availability of the blast furnace. This article describes the Top Charging Unit including DANCU (Danieli Charging Unit) - a robust hydraulic system. The main focus employed by Danieli and Danieli Corus during the development of this system has been availability and maintainability of equipment. This chute type charging unit has only few major moving parts, none of which is complex or vulnerable. The article also describes the main challenges of the project at Zaporizhstal, such as the use of hot sinter.

Oct 30, 2017

By Jean Viana Bahia, Antônio Adel dos Santos, Vicente Tadeu Lopes Buono

During cold rolling of Cr-Mo alloyed DP steel, considerable oscillation of thickness may occur. The literature points out that such occurrence is due to non-uniform cooling of the coil after the hot rolling process. Since the austenite transformation in this steel continues after coiling, the microstructure and, consequently, mechanical properties are very susceptible to natural variations in cooling rates associated with distinct positions of the coil. The influence of coil cooling conditions on thickness oscillation during cold rolling was evaluated in this work by using both industrial experiments and dilatometer tests. It was verified that an industrial coil presented large variation of mechanical properties associated with its heterogeneous microstructure. Consequently, thickness oscillation occurred during cold rolling. Dilatometer tests simulating hot run-out table and coil cooling showed that the austenite transformation is very slow under small cooling rates that occur after coiling. Thus, the slow transformation rate makes the coil very susceptible to environmental conditions around it during its natural cooling and is responsible for variation in mechanical properties of the coil. To ensure the formation of a more homogeneous microstructure in the whole coil, it is necessary either to make use of technologies that improves the cooling uniformity or to adjust the steel alloy design. The latter alternative has been done with relative success by using conceptions with lower amounts of Cr and Mo.

Oct 1, 2019

By Markus Reifferscheid

Industry 4.0, Digitalization, Internet of Things (IoT) and Cloud Computing are predominant topics in the world economy at the moment. At the ABM week 2017 Dr. Markus Reifferscheid, Head of Research & Development of SMS-group, will talk about the proceeding digitalization in the steel industry with selected examples of SMS-group. He will present advanced concepts and solutions which are currently being developed.

Oct 30, 2017

By Renata Cristina Teixeira

The lubricant oil is a complex mixture of different basestocks and additives. Engine oils evolved from the use of pure mineral basestocks back in the early years of automotive industry to the advent of synthetic, fully formulated, low ash lubricants. This evolution was driven by a number of factors, such as new engine designs, extended durability needs, increased fuel economy needs, environmental concerns, feedstock prices and availability and legal issues. This paper uses technology prospecting on literature and patents databases to allow an investigation on the historical evolution of engine oils. Main basestocks (mineral, hydrotreated, polyalphaolefins, esters) and additives (antioxidants, antiwear, friction modifiers, detergents and dispersants) are characterized according to their research effort. Technology prospecting data is crosschecked against the evolution of engine oil classes, allowing an analysis of how the main drivers push the development of lubricant oil quality. A research effort was identified in late 1990’s until mid-2000’s and related to the adoption of chemical limits for lubricants. Different patterns for the articles and patents publication account for the high value technological knowledge has in this industry. Technology prospecting is seen as a useful methodology for the understanding and forecast of lubricant technology movements.

Jul 31, 2018

By Patrícia Mundim Campos Faria

The process of particle size reduction by grinding is inherently inefficient and involves high capital and operating costs. In particular, ball milling is one of the important unit operations in the iron ore pelletizing process. The mill product, due to its physical properties, determines the efficiency of subsequent stages of classification, filtration and pelletizing, thus impacting the quality of iron ore pellets. The work demonstrates the application of the population balance model in the optimization of a full-scale ball mil circuit grinding pellet fines with the aim to evaluate the optimal solids concentration to improve iron ore pellet quality. Initially, detailed experimentation was carried out in a 25.4 cm diameter batch mill and a relationship for mill scale-up using a linear population balance model in wet grinding systems was established. The selection and breakage parameters and the specific selection functions were determined for pellet feed iron ore. It was possible to identify the non-normalizable nature of the breakage functions of the ore studied, which were modeled properly. Afterwards, as a result of incorporating the specific selection functions and breakage functions into the linear population balance model, it was possible to predict product size distributions in the pilot and plant scale mills (0.416 and 5.18 m diameter, respectively) from data obtained in the 25.4 cm diameter mill. Finally, with this scale-up procedure it was possible to appraise the plant scale optimization via laboratory scale grinding mill tests. The effects of changing percent solids were assessed in order to improve the industrial mill performance and the optimal value should be in the range from 76 to 80%.

Aug 1, 2018

By Ernesto Gustavo Maffia

En la actualidad, el moldeo por inyección es una tecnología muy utilizada en el procesamiento del plástico pues permite fabricar formas geométricas complejas. Para fabricar los moldes se utiliza ampliamente la aleación C17200 (Cu-2%Be), pero están en desarrollo algunas alternativas con aleaciones base cobre libres de berilio, que tienen valores de dureza por encima de los 30 Rockwell C y buena conductividad. Las aleaciones base de cobre, tipo CuNiSiCr son las más adecuadas como reemplazo. El siguiente trabajo trata del estudio y desarrollo del proceso de fabricación, por fusión, colado y conformado, de una aleación tipo CuNiSiCr de alta dureza y buena conductividad para ser utilizada en la fabricación de moldes de inyección para la industria del plástico. Los resultados preliminares de esta investigación demuestran que a través del aumento sistemático en el contenido de níquel y silicio se consigue un aumento de la dureza (>32 Rockwell C) y una aceptable conductividad eléctrica (˜25%IACS). El fenómeno segregación interfiere fuertemente en los tratamientos termomecánicos, pues se forma una segunda fase interdendrítica, de características frágiles, que genera fracturas en el conformado. Los resultados demuestran que la aplicación del recocido total y control de la temperatura durante la forja minimizan este problema.

Aug 7, 2018

By Haruki Inami, Takashi Ishida, Kazuhiro Ohara, Hiroyuki Imanari

The highly competitive business environment of the international metals industry is driving demand for more cost-effective operation of steel making facilities, rolling mills, and strip processing lines. Achieving stable operation is vital if the steel industry is to produce high-quality products constantly and productively. In recent years, advances in computer processing speeds, data acquisition rates, and data storage capacity have rapidly led to greater use of the new technologies of big data, analytics, the IoT, and AI by control system designers and process engineers, and the introduction of industrial applications. The “Smart Rolling Mill” solutions for hot strip mills have been developed by our group with the goal of achieving sophisticated, state of the art, and automated operation in steel rolling mills. The various solution engines improve process stability, increase the performance of mill equipment, and provide improved process control. These solution engines are based on extensive knowledge of the rolling process and the associated control systems. Two solution engines in particular are the diagnosis systems for rolling condition and for product quality that contribute to cost-effective operation and lower yield loss. This paper focuses on the diagnosis systems for rolling condition and for product quality in hot strip mills. Advanced information technologies using big data analytics and machine learning are applied to real-time data collected from the automation system that controls operation and the rolling process. We have developed diagnosis solutions for rolling condition and product quality utilizing predictive and clustering diagnosis. Predictive diagnosis prevents serious problems by detecting changes in the state of the plant or in the rolling condition. Clustering diagnosis classifies patterns of fluctuation in product quality trend charts, providing effective tuning guidance for improving product quality. This paper describes these applications with several examples.

Oct 1, 2019

By Nigel Marx

In order to understand (and ultimately to predict) the friction reduction resulting from the use of polymer solutions, the rheological properties of model polymer solutions have been measured over a wide range of shear rates. Both temporary and permanent shear thinning have been observed. By using base fluids of different viscosities it has been shown that permanent shear thinning depends more closely on the shear stress experienced by the fluid than on the strain rate. Hydrodynamic measurements have been made on the polymer solutions using a compliant ball on flat lubricated contact that operates in isoviscous-elastic conditions. The measured friction values can only be predicted with reasonable accuracy if the measured shear thinning properties of the lubricant are taken into account in the hydrodynamic model.

Jul 31, 2018

By Leonardo Camilo dos Reis, Edmilson Fernandes Dadomi, Claudio Silva de Paulo

In the hot strip mill production, one of the factors that may affect the productivity is the occurrence of failure due to the geometry of the strip at the exit of the rolling mill, because the tip of the strip can turn-down or turn-up. This study had the objective of evaluating the behavior of the strip when leaving the working rolls, through numerical simulation, aiming to know the influences of the main variables that govern the formation of the turn-down. The methodology consisted in performing the computational simulation of the strip mill and to vary the operational and geometric parameters that could influence the process. The results showed that the rolling of hot strips of HSLA material with final thickness varying between of 3 to 6 mm and a reduction of 6.6% to 11.0% in the last stand of a hot strip mill, tends to bend towards the roll with larger diameter, higher friction coefficient , higher temperature and lower limit of material flow. It was observed that the variation in diameter is the main factor that contributes to the formation of the curvature of the front-end of strip. Based on these results, several measures were implemented in the industrial line, with a significant reduction in the occurrence of turn-down.

Oct 2, 2019

By Bi Zongyue, ZhangYongqing, NiuTao, Guo Aimin

Over the past twenty years, significant advances have been made in the field of microalloying steels and associated applications, among which one of the most successful application cases is development and application of heavy-gauge X80 coil with high temperature processing HTP practice used for China's Second West-East pipeline, the longest X80 pipe in the world. During this process, HTP design concept has been sucessfully applied to develop 18.4mm X80 coil with demanding low-temperature fracture toughness requirements. In the meanwhile, China's metallurgical workers have further optimized HTP design concept with the aid of powerful rolling mill and coiling equipment, and made it possible to develop 21.4mm X80 coil used for Russia-China East line. In the paper, we would simply review the development history of high-strength pipeline steels, and then give more priority to the fundamental points for sucessful development of 18.4mm X80 coil and SSAW pipe, which paved the way for subsequent development of 21.4mm X80 coil and SSAW pipe. Finally, we would present the test results of mass production and burst tests, and dispel the suspicion that SSAW pipes made of X80 coil are more qualified to resist ductile fracture.

Oct 1, 2019

By Mario González Ramírez

The safe transport of sour gas requires steels with enhanced hydrogen induced cracking (HIC) resistance. Centerline segregation bands of high hardness microconstituents and non-metallic inclusions are the heterogeneities usually linked to HIC failures in pipeline steels. Full-scale production heats of a new low Mn, Nb microalloyed steel were produced by different steel mills aiming at the application in sour gas environments. The new alloy design provides both effective strengthening and control of sulphide inclusions. Coil microstructure consisted of fine grained ferrite with a small volume fraction of uniformly dispersed eutectoid aggregates. Most importantly the microstructure was uniform in both the longitudinal and transverse directions and exhibited exceptional consistency. Samples from this steel were submitted to HIC testing according to NACE standards TM0284-2003 without any sign of cracking. The results, so far, confirm that this new alloy design provides the unique opportunity to economically produce a high strength pipe steel grade with improved sour service resistance for the linepipe industry.

Aug 8, 2018

By Ivan César Lopes Diniz, César Romero Afonso Goulart Júnior

Mandrels are tools applied to manufacturing seamless tubes. In VSB plants (Vallourec Soluções Tubulares do Brasil), it is used in two mills. Mandrel and PQF Mills. This is an expensive tool due its alloy (hot work tool steel – AISI H13) and lengh (between 12 meters and 22,5 meters). An opportunity to apply mandrels from PQF in Mandrel Mill has been identified. However, mechanical properties of PQF mandrels must be improved. This work presents the heat treatment process of Quenching and Tempering developed internally at VSB to improve PQF mandrel properties aiming to achieve Mandrel Mill requirements. Hardness and metallography tests were performed before and after some steps of the heat treatment to characterize and validate the process.

Oct 5, 2019

By Bernhard Hiebl

Global trends that are constantly challenging the iron and steel producers are related to worsening of the iron ore grades, higher substitution rates of main iron ores to cheaper raw materials due to economic pressure and increased environmental standards. Changing the raw materials in an operating plant can significantly influence the sintering or pelletizing process. Adjusting all process parameters to regain stable and high productive operation takes considerable time and causes production losses. Furthermore changes in raw materials lead to variations in the process gas flows and emission concentrations.Therefore SVAI developed two models for numerical simulation of sintering process and pelletizing process. Amongst others the models are based on Ergun equation and include chemical reactions of the related process. For already operating plants the simulations shall predict changes of the process parameters when raw materials are exchanged or when operational parameters are varied. Furthermore the simulations give advantageous information for the design of green field plants and allow the simulation of different plant configurations.The objective of this paper is to demonstrate what the latest developments are in these numerical simulations and what Siemens VAI is doing to overcome the remaining challenges in this field.

Aug 2, 2018

By Ronaldo Esteves Ribeiro, Jefferson Felipe Faria Clemente, Carlos Victor Francisco dos Santos, José Herbert Dolabela da Silveira

n recent years, the market for thick plates has been highly competitive, in this scenario the plates quality is a critical success factor. In this process, the quality of the cut in thick plates is one of the important requirements for the customers, by the visual aspect as well as the technical aspect of the plate application. In the shear line, the cutting is done by shearing to trim tips, subdivide plates, trim side edges, remove samples, eliminate defects, etc. The cut is obtained by the penetration of the upper knife in the plate, causing plastic deformation in a certain region and hardening. If the clearance between the knives is adequate, the cracks will be close to the centre of the plate thickness and will result in a good cut quality. This work will present the theory of cutting of thick plates, the types of shearing, the quality of the edge in the cut, the types and the main characteristics of the knives.

Oct 1, 2019

By Eduardo Dominguez Trindade

Lubricant oils are subjected to reciprocating movement in the piston ring/cylinder tribocouple of automotive engines. In this kind of movement, the relative speed oscillates between zero and a maximum, and therefore the lubrication regime goes from boundary to hydrodynamic. Tribotests are widely used in laboratories to hint at the friction developed in these systems. In the present work, a SRV tribometer was used to evaluate the friction behaviour of lubricant oils under reciprocating movement up to 60 Hz. A high acquisition rate allowed the analysis of data inside each reciprocating cycle. Both a pure base oil and a fully formulated lubricant were used. Changes in the contact pressure, viscosity and speed were seen to influence friction, which was correlated to the relative thickness predicted by Hamrock-Dowson equation. While some observed characteristics were typical consequences of the Stribeck curve, other effects were also observed, such as the occurrence of seizure at high reciprocating frequency. A lower boundary coefficient of friction due to additive package in the formulated oil was also observed. The results allow a better understanding of friction in reciprocating cycles and can be used to evaluate the performance of oils and surfaces in laboratory prior to engine testing.

Jul 31, 2018

By Armando Vazquez Arredondo

Tenova Goodfellow Inc. has successfully installed the proprietary EFSOP® (Expert Furnace System Optimization Process) system in over 80 installations worldwide. For over 15 years, the EFSOP® System has successfully achieved its main objective of improving performance and operating costs through the reduction of electricity, oxygen, methane, injected and charge carbon use. Using the off-gas information provided by the EFSOP® System, Tenova Goodfellow Inc. has now developed a solution for detecting abnormal water events within the EAF steelmaking process. When water form enters the EAF, it immediately forms into water vapor (H2Ogas) and a proportion of the resulting water vapour will further react and dissociate to H2. Effective water detection technology must be capable of detecting BOTH forms of water; H2Ogas & H2. Tenova Goodfellow has the technology to measure in real time and simultaneously H2Ogas & H2. This paper will provide a summary on how the EFSOP Water Detection Technology® is used during the EAF operation. Details regarding the technology, software, alarm rate and information on sensibility water trial tests will be provided within this paper.

Aug 16, 2017

By Kurt Herzog

State-of-the-art automation information technology and connectivity enables the digitalization of steel production that goes far beyond conventional automation of industrial production. Initiatives have been started around the globe to foster digitalization like IIoT (Industrial Internet of Things) in the US, Industrie 4.0 in Germany or China 2025. Primetals Technologies is actively driving the digitalization shaping the future of steel production. Intelligent combination of sensor technology combined with digital models as well as quality and production planning and control systems leads to new dimensions in product quality and production cost reduction. New diagnostic ways allow intuitive fault tracing or processing to support faster maintenance. Digital assistants support both operation and maintenance using context-oriented or self-learned information.

Oct 30, 2017

By Bart de Graaff, Victor van Straaten, Edo Engel

The hot blast system is key ancillary plant equipment with respect to safe and stable operations during a long blast furnace campaign. Hot blast stove designs have been optimized to such an extent that in some cases, their lifetimes have surpassed the campaign lengths of the associated blast furnaces by a substantial margin, with the exception of the burner and a few critical areas. This article presents recent developments with respect to designing, building new and operating existing hot blast systems for a long lifetime and at optimized performance. These developments include fundamental improvements such as dome combustion designs as well as increasingly comprehensive packages for inspection, assessment and maintenance techniques. Examples of such techniques are burner replacement with the hot blast system at operating temperature, improved double shell approaches and TOFD measurement applications.

Oct 1, 2019

By Alberto Moreira Guerreiro Brito

Componentes tubulares de parede fina têm aplicações em diversas áreas industriais, na forma de trocadores de calor, amortecedores de impacto, sistemas de fixação, absorvedores de energia, pré-formas para outros processos de conformação mecânica, etc. Neste trabalho é apresentado um estudo de natureza teórico-experimental envolvendo o processo de expansão de extremidades de tubos. Busca-se determinar os parâmetros que governam o mesmo, suas limitações e se a conformação em matriz pode ser uma alternativa viável a processos mais complexos, como por exemplo, hidroconformação. É feita a caracterização do material (uma liga de alumínio ABNT 6061) através do levantamento de curvas de escoamento, perfis de microdureza Vickers, e deformabilidade quanto ao surgimento de trincas e de instabilidade plástica (flamblagem). Ao final são conduzidas simulações através de elementos finitos e experimentos do processo de expansão. São variadas características geométricas dos tubos e das ferramentas e o estado do material (diferentes tratamentos térmicos).

Aug 8, 2018

By Delciane Porfiro, Tiago de Mattos Serodre, Antônio Eduardo Clark Peres, Valdirene Gonzaga de Resende

The evaluation of the effect of the addition of carbon nanotubes (NTCs) directly to a etheramine on the flotation recovery of the quartz at pH 10.5 was carried out by means of microflotation tests in Hallimond tube. The quartz flotation was evaluated using 0.1% (w/v) etheramine solution with different percentages of carboxylic functionalized NTCs. The increase in the percentage of functionalized NTCs increased the flotation recovery to a maximum and from this it was observed a reduction of the recovery of the mineral. Pure etheramine and etheramine with the NTCs were characterized by FTIR spectroscopy and thermal analysis. FTIR spectra of both pure etheramine and etheramine with NTCs clearly showed peaks with the same wavelengths and diagnostics of the cation etheramine and acetate anion. Thermogravimetry indicated that the etheramine + NTCs-COOH mixture lost approximately the same weight percentage over a larger temperature range. In addition, the interaction of the nanotubes with the etheramine caused them to decompose at a lower temperature.

Oct 3, 2019