Search Documents

By Nicholas J. Grant, Chih-Chung Wang

TO phase of the Ti-0 system has the structure of NaCl and has a wide range of solid solubility.' In the course of studying the Ti-Cr-0 ternary system, binary alloys were made of iodide titanium and high purity TiO,. It was found from X-ray studies of the binary alloys that a transformation of the TiO appears to take place at a temperature near 925°C. Evidence of this phase change is best seen in Fig. 1. Fig. 1A shows the X-ray spectrometer pattern (CUKa radiation) of an alloy of 25 wt pct 0 corresponding to the stoichiometric composition of TiO.

Jan 1, 1957

By T. Turner, C. L. Zimmerman, U. Kappus

The purpose of the project is to divert flood flows of North Potato Creek. The project is located in the southeast corner of Tennessee near Copperhill, approximately 160 km north of Atlanta, GA. The project consists of: a 28-m high dam, a 0.9-m diam outlet conduit, an emergency spillway, and a 4.0-m diam hard rock transbasin diversion tunnel. This flood-water management system was part of Cities Service Co. mine safety program for the Cherokee ore body, which is partially located within the creek channel. The following paper describes the entire project development from feasibility studies to design and construction management.

Jan 1, 1981

By Thomas M. Drown

At the meeting of the Istitote in New York, in February, 1880," I described a process of determining sulphur iu metallic allphides, with especial reference to the determination of pyrites in coal. The procem, as then described, is as follows: A solution of sodium hydrate, of 1.25 specific gravity, is saturated with bromine. If an excess of bromiue is used it must be neutralized by the addition of a little more sodium hydrate. The pulverized mineral or coal is moistened with 25 c.e. of this solution autl heated, then hydrochloric acid is added cautiously to just acid reaction. This operation is repeated with another 25 c.c. of the alkaline solution, and again rendered acid. The mixture should be kept hot. The contents of the beaker or dish are then

Jan 1, 1881

By Joseph Cervik

INTRODUCTION Common methods of controlling gob gas in U.S. mines are by means of ventilation of gob areas and gas drainage through surface boreholes. Costs of drilling surface gob holes increase as deeper coal- beds are mined. Where gob holes cannot be drilled because of topography, ventilation is the only means of control. Even then, sufficient air may not be available to dilute methane in the bleeder entries to acceptable levels. Thus, new methods of gob gas control need to be developed that are independent of surface topography, and of the mine ventilation system, and less costly than present systems. Except for slight variations in procedures and equipment, Great Britain, West Germany, France, Belguim, Poland, and Czechoslovakia use a common methane control method that is different from the system generally used in the United States. This Bureau of Mines paper reviews European mining methods, mining conditions, and methane control technology and discusses their applicability to U.S. mines.

Jan 1, 1981

By S. F. Turcotte, B. J. Grierson

At the Q. I. T. ilmenite smelter, nine electric furnaces produce titania slag and iron At high power levels, a furnace requires either a slag or an iron tap approximately once an hour, using rail cars as slag receptacles and ladles for iron. The correct scheduling of taps is an important operational tool due to peak power load and operational considerations. Over recent years, large increases in furnace capacity have imposed severe strains on the product handling facilities. This situation results in loss of production when several taps are bunched, because of an in- ability to handle many taps simultaneously. An on-line computer program has been developed to generate schedules for tapping a single furnace. By improved scheduling, this program can en- large the tonnage of each tap and minimize the number of taps, while reducing traffic congestion and unit cost s. Future plans call for extension of this technique to all nine furnaces with addition of a master scheduling program to optimize the overall traffic flow in the smelter aisle.

Jan 1, 1969

By E. A. Khopunov, V. I. Revnivtsev

The process of triboelectric separation from the point of view of its potential for selective separation of various mineral particles can be described as "dry flotation." Large scale practical applications of this technique are limited because suitable models which can describe contact charging of mineral particles have not been developed. Among the various concepts a promising one is an attempt to change development in dielectric minerals within the limits of contact phenomenon in semiconductors. Experimental investigations reported in this paper indicate that the charge development is mainly a result of contact electrification of dielectric minerals characterized by "donor" and "acceptor" type energy spectra due to lattice defects.

Jan 1, 1980

By B. Yu, H. M. Lee, R. P. Gardner

Some preliminary results are given on the use of radioactive tracers for implementing the mechanistic approach to flotation. The process studied is an industrial one for the cleaning of sand for the production of glass. The radioactive tracers employed are those produced from intrinsic elements in the sand by neutron irradiation in a nuclear reactor. The results indicate that the technique will be useful for the determination of flotation simulation mechanistic model parameters on operating industrial processes without interruption of their normal operation.

Jan 1, 1980

By Gary E. McIntosh

This paper will discuss a US Bureau of Mines project designed to assess and predict the impacts which surface coal mining will have on the regional shallow groundwater systems in the Powder River Basin. The primary objective will be met through the accomplishment of the following: (1) The design and establishment of a regional network for monitoring shallow groundwater systems in the basin; (2) monitoring the direction and rate of flow, water quality, and aquifer characteristics of the shallow groundwater systems; and (3) development of a regional groundwater simulation model, with appurtenant subroutines to determine local effects.

Jan 1, 1980

By Robert Gilman Brown

There are few disasters so difficult to deal with as an underground fire. It is inaccessible at best, and generally unapproachable ; and it finds most material in the very places where it can do most harm, namely, in large stopes and in " heavy " ground where timbers are massed, and in shafts and level-stations where there are inevitably strong drafts to make the burning yet more fierce. The fire constituting the subject of this note occurred in the shaft of the Standard mine at Bodie, California, and originated after the departure of the night-force at 3 a.m., being discovered by the men going to work at 6.30. At that time it had gained already considerable headway, and was throwing smoke plentifully from the collar of the shaft. It must be premised, for understanding of the situation, that in this shaft all hoisting is done to the 320-foot level, where the material is dropped by chutes 30 feet. to the tunnel-level, through which it is run to the mill. Hoist and sheaves are all placed

Jan 1, 1897

By Harry L. Washburn

Use of coal thermal dryers has steadily increased since 1928 when one of the predecessor companies of the present Consolidation Coal Cu. constructed a complete preparation plant with thermal dryers. Today there are about 25 additional preparation plants that, all together, use over 65 individual thermal dryers of almost every type. The thermal dryer is a heat generator and the unit may have a separate furnace or a firebox that is an integral part of the dryer. It is also a materials handling device that allows an intimate mixture of wet coal and hot gases with instrumentation for temperature control and. in some cases, the more difficult flow rate of hot gases. The materials handling portion of the dryer is subject to the normal wear and teal of any similar device plus effects of heat, water vapor, moisture: and, sometimes, acid. With present emphasis on air pollution. most fine coal dryers have wet scrubbers.

Jan 8, 1963

A regular feature of the December issue is to be abstracts of graduate theses in the mineral industry field presented during that year. The following abstracts were submitted for this first article in the series.

Jan 1, 1975

By Robert Mehl

IT has been shown that quenched iron of high purity exhibits a Widmanstätten figure much resembling martensite in appearance.1 This figure exhibits a maximum of four directions of the surface traces that characterize it, suggesting that a Fe forms from y Fe in plates parallel to the {111}, octahedral, planes in the y lattice. Because of this, and also because of the general similarity to the structural appearance of martensite and to the Widmanstätten figure obtaining in slowly cooled hypoeutectoid steels it has been suggested2 that the orientation relation-ships obtaining between the y and a phases in pure iron are identical with those demonstrated in martensite3 and in slowly cooled hypoeutectoid steels,4 and indeed that the crystallographic mechanism of formation of a Fe from y Fe is the basic mechanism determining the orientation relation-ships found in both martensite and in slowly cooled hypoeutectoid steels. This paper will present experimental evidence in support of this view.

Jan 1, 1934

By R. A. Irvine

The use of large vibrating screens presents unique challenges to the screen manufacturer, the plant designer, and the plant operator. The design of vibrating structures that span greater unsupported distances is critical to the reliability of a screen subjected to billions of fatigue cycles. Larger percentages of total plant production become dependent upon fewer, larger vibrating screens. Plant designers and operators must plan for equipment maintenance in a manner which optimizes the production availability of large vibrating screens.

Jan 1, 1985

By I. C. White

Only two factors appear to be directly responsible for the geographic distribution of sulfur in the coal fields of West Virginia: these are the stratigraphic position of the coals in question, and the eastward or westward location of the deposits. There appears to be a progressive increase in the sulfur content of West Virginia coals from the oldest Peqnsylvanian deposits in the Pocahontas, New River, and Kanawha Groups of the Pottsville Series up through the Allegheny, Conemaugh, and

Jan 1, 1920

By D. Malhotra, R. M. Hoover, F. N. Bender

The paper discusses the effect of aeration and agitation on grade and recovery of molybdenite. A series of factorially designed flotation tests were carried out in a "Leeds Automatic Laboratory Flotation Cell." Analysts of flotation results indicate that molybdenite has fast floating and slow floating components. The rates of fast floating components, which do not create a problem inflotation, could be varied by changing agitation or airflow rates. However, the rate of slow floating components was stable and was only a function of residence time. Aeration has a significant effect on the grade of MoS2 and only a slight effect on the recovery of MoS2. Agitation has a slight effect on the grade, but does not effect the recovery of molybdenite. The implications of the results on the design of flotation cells and control and optimization of the existing circuits are also considered.

Jan 1, 1981

By Charles M. Brinckerhoff

The Potrerillos mine of the Andes Copper Mining Co., a subsidiary of Anaconda Copper Mining Co., is 100 miles east of the coast town of Chanaral, in the Province of Atacama, Chile. In December 1926, the plant was placed in operation and has operated continuously ever since. Block caving is the only mining method used, as it is especially suited to the grade of ore, the position and shape of the ore bodies, and the character of the ground. At the present time there are three haulage levels, which handle oxide and sulphide ores, and production from them averages 31,000 short tons daily. The purpose of this paper is to describe the layout, equipment and systems used on the gathering or main haulage levels. Haulage Layout Because of the shapes of the ore bodies, their distances from the dumping pockets

Jan 1, 1946

By H. N. Mills

The glass industry is a major user of many industrial minerals in the manufacture of its product. It is the intent of this chapter to: (1) acquaint the reader with the glass industry by including a few production statistics, and then (2) cover the various aspects of the major raw materials used to make glass. Some of the items covered are: type of materials, their function in glass, their composition, cost, and the relative quantity used in glass vs. totals produced. In addition, a discussion of glass raw material specifications, some byproduct materials used in glassmaking, and comments on future prospects related to the environment, technology, and growth are included. The matter of glass compositions, properties, and batches is considered beyond the scope of this chapter which deals only with raw materials. For more details on the particular minerals and rocks, the reader is referred to the commodity chapters in this book.

Jan 1, 1975

The Board of Directors on April 18, 1940, adopted a resolution providing that "no person who has been awarded any one of the four medals-Douglas, Saunders, Lucas, and Rand-is eligible for consideration for any other of the four medals " Later in the year the rules for the award of these four medals were revised and, so far as practicable, made uniform The medalists are elected by the Board of Directors, on recommendation of special standing committees of award, appointees on which serve four-year terms and are engaged in the branch of industry represented by the respective awards Under the rules only members of the committees of award are eligible to propose candidates\ for the nomination

Jan 1, 1952

By R. L. Grayson, Y. J. Wang

This paper presents an application of goal programming (GP) to major mining machinery purchases based on historical operating data on mechanical downtime and production. The GP technique, an extension of integer programming, is used to maximize an objective function comprised of deviations away from management-preferred financial goals. Different capital budgeting techniques are used to evaluate capital proposals, and the results of these analyses are combined and weighted in a maximization of profits objective function. The GP method gives an optimal solution to a multiple goal problem. A sensitivity analysis is performed to determine the effect of a variable production improvement condition or a variable budget control con¬dition on proposal selection.

Jan 1, 1984

By Colin G. Wilson

This paper considers the heavy liquid laboratory tests used to determine the amenability of a potential ore to the heavy media process. The results of the laboratory testing are correlated to actual plant performance and establish design parameters for the heavy media process. These parameters are used in the development of the metallurgical flow sheet and in the sizing of equipment in the metallurgical plant design.

Jan 1, 1978