Search Documents

By G. E. Steudel

The study of the possibility of effecting a lower cost in the manufacture of pig iron reveals the importance of the ever present question of slag chemistry and volume. Factors that determine slag chemistry and volume are the impurities in the ore available, the ash-sulphur content of the coke, and a flux material necessary to promote removal of sulphur. Of these, the ores present by far the major source of impurities and what may prove to be the lowest practical slag volume with desired chemistry in one locality may be considered low or high in some other center of iron manufacture. The Chicago district is not only blessed with ores of high quality, but with excellent coke and flux materials as well. It is the intent of this paper to discuss slag problems at the South Works only, where burdens consist of Mesabi ores, Michigan stone, and coke ranging from 7 to 9 per cent ash and containing an average of 0.57 per cent sulphur. Early in the development of modern blast-furnace practice, the consideration of slags was secondary to the many adjustments of mechanical difficulties, such as furnace lines, stock distribution, stove design for obtaining higher blast temperatures, improved chemical segregation and size of raw materials. Furnace operators, after making these improvements, turned their attention to the study of other refinements in practice, of which slag chemistry appeared to be the most important. It is only within the last two decades that operators have become familiar with the various aspects of slag compositions. The industry, while rather slow in its recognition, is indebted to such investigators as Rankin,1 Wright,1 Feild,2 Royster,2 McCaffery,3 Kinney,4 Holbrook,5 and Joseph,5 whose researches concerning the elimination of sulphur within the blast furnace and the effect of slag composition upon melting point, viscosity, and desulphurizing power have established criteria for the selection of slags of the requisite quality. Large slag volumes result in higher coke consumption and cost of disposal. Any attempt to lower slag quantity must be accomplished

Jan 1, 1940

By W. F. Holbrook

In a previous paper1 a method for the measurement of the comparative desulphurizing power of slags was described and data were presented covering the range of likely slags containing up to 10 per cent MgO. In the present work the range is extended to include slags containing up to 20 per cent MgO, and the effect of temperature on 5 per cent and 15 per cent MgO slags over the range 1475' to 1525' C. is included. The method used was that described in the previous paper except that some of the temperature measurements were made with a noble-metal thermocouple instead of a tungsten-graphite thermocouple. Twelve-gram charges of 0.8 per cent sulphur-metal and 5-gram charges of slag were subjected to heating for 30 min. at a prescribed temperature. The charges were analyzed for sulphur content. For purposes of comparison, desulphurizing power is defined as the ratio of the percentage of sulphur found in the slag to that found in the metal. Six slag and metal charges were made coincidentally in 5/8in. holes in a section of an electrode graphite rod. One slag and metal charge was used as a control by means of which adjustment in the desulphurization value could be made for small variations in temperature and other factors. For convenient presentation of the data, the slags are arranged in groups in each of which one of the four main slag components is constant. Thus, the 15 per cent MgO slags are presented separately from those containing 20 per cent MgO. Slags with Magnesium Oxide Constant 15 Per cent Mg0.—The data on slags containing 15 per cent MgO cover a composition range of 24 to 50 per cent SiO2, 5 to 27 per cent A1203 and 24 to 53 per cent CaO. Variation in composition has been in steps of 2 per cent over much of the area. Because the change in desulphurization power is generally gradual with gradual change in composition, certain sections have been covered in steps of 4 per cent and even

Jan 1, 1938

By A. J. Bartlett

Island Creek conditions are generally referred to as ideal; yet, as at all other properties, there are all known hazards of coal mining. The hardest of these hazards to combat is the human element. The basic thought in the minds of the management of these properties is to produce coal with the utmost safety, and it has impressed upon its supervisory force that it does not want a ton of coal unless it can be produced safely. This company has instituted a mine inspection department, which reports direct to the general manager, arid all matters pertaining to safety come under the direction of this department. Through the medium of the inspection department, the management is kept in touch with the actual conditions existing in general at all mines. Inspections are made regularly arid continuously; that is, at all times while the mine!: are in operation some sections of some mines are being examined. These inspections cover all active and inactive workings. Miners are contacted in their working places and other employees at their respective, work. A thorough check is made to see that the state mining laws are complied with and that company safety rules arc being observed. Night shifts receive the same attention as day shifts. All violations and dangerous practices are brought to the attention of the plant supervisory force with suggestions and recommendations; major hazards of emergency nature are taken up immediately with the management. Periodical inspections are also made of all tipples, preparation plants, dumping and hoisting equipment, to see that all machinery is properly guarded, and walkways and platforms properly fenced; conditions of equipmcnt and mechanical defects are also reported. Reports of inspection are written in letter form and in such a manner as to give the management a picture of the existing conditions at the time of inspection. Copies of inspection reports are forwarded to the superintendents with the general manager'? comments. It has been said, "There is nothing under God's heaven that justifies. your creation or your citizenship but this gospel: ' That the next greatest

Jan 1, 1938

By A. C. Richardson

Troughs or launders are probably the oldest machines used for ore concentration, and their development was suggested no doubt by the natural segregation and stratification of materials that take place in the bed of a stream. Trough washers for coal cleaning were first used in France and Germany about one hundred years ago and have been used in some form or other ever since. The early launders were intermittent or batch machines, and only comparatively recent developments have made them continuous. The chief disadvantage of early launder systems as applied to coal has been that when a satisfactorily clean coal was produced the loss of good coal in the refuse was excessive. Other disadvantages have been the large quantities of water and the great lengths of troughs necessary to treat moderate tonnages of feed. One of the most widely used types of trough washers is the Rheolaveur, which has been developed in the last 25 years. Fig. 1 shows a more or less standard arrangement for fine coal. In this there are four trouglis placed one below the other and sloped a few degrees from the horizontal. Rheo-boxes or draws are provided at intervals in the bottom of the trough for the removal of material deposited from the stream. These draws are spaced substantial distances apart. Some of the rheo-boxes are provided with upward currents of water to modify the horizontal current stratification. In operation it is the function of the first two troughs to remove all refuse material and permit only clean coal to be discharged over the end. In order to accomplish this, large quantities of coal are drawn through the rheo-boxes. The third and fourth troughs are used to recover the coal discharged through the boxes of the first two troughs as a middling product and to discharge a clean refuse. The middlings are returned to the first launder and are usually about equal to 40 per cent of the raw coal being fed to the launder. In considering launder processes, one would reason that the conditions of extreme crowding under which stratification takes place in a flowing stream should effect complete separation in a single pass down a launder.

Jan 1, 1938

By W. E. Curran

For years the geographical isolation of the Southern iron-ore district from the great producing centers in the North and East enabled it to meet its conditions and solve its own problems without regard to the practices and policies of other districts, but during the past few years distances have been shortened, practices and wages are being standardized, and these changing conditions have brought new problems to the South. Development of Pig Iron in the South The development of the pig-iron business in the South was very slow during its early years, gained speed rapidly in the latter part of the nineteenth century, reached its peak in 1918 and was on the decline before the depression that began in the latter part of 1929. The first blast furnace in Alabama was built at Cedar Creek in 1818, the year before the state was admitted to the union. In 1830, Daniel Hillman was sent from Tuscaloosa to found an iron works in Roupes Valley, where rich pockets of brown ore were numerous. He built a forge on the site of what later became Tannehill furnace and called it the Roupes Valley Iron Works. There pots, pans, plows, and horseshoes were made of metal from his Catalon forge; shaped by a large hammer operated by water power. Daniel Hillman died in 1832 and the ironworks lay idle until 1836, when Col. Ninion Tannehill bought the property, rebuilt the forge and, using slave labor from his plantation, operated and enlarged the works. By 1845 he had built two crude furnaces and did a flourishing business in ovens, skillets and kettles, which found a good market all over the South. In 1855, the plant was sold by Colonel Tannehill to Moses Stroup, an experienced ironmaster from Pennsylvania. He tore down the old furnaces and built a new plant, the ruins of which stand today (Fig. l). This furnace plant operated continuously until it was destroyed by Northern troops in 1865. It was never rebuilt, so that the shell in the picture is the same furnace that made many tons of guns and shells for the Confederacy during the war period.

Jan 1, 1938

By H. J. Rahilly

Mine fires, in the Butte district, have been a source of trouble and expense for the past thirty years, for while the actual fire area in most of the mines has been comparatively small, the handling of the gas has generally been a much larger problem than the actual putting out of the fire. The chief causes of these fires have been: Defective electrical equipment, incendiarism or carelessness, and spontaneous combustion. While fires from the first two causes have been numerous, they have generally been discovered and extinguished before they became very serious. Spontaneous combustion has been the cause of most of the large fires. Sufficient heat has been generated by ground movement, high rock temperatures, and decomposition to set fire to inflammable materials (tarred ropes, canvas, dry timber, manure, and hay) left in the gobs some years ago. Also, the heat resulting from the oxidation of the fine broken sulfide ore is sometimes sufficient to set fire to the timbers. In 1906, a fire was discovered on the 1100-ft. level of the Minnie Healy mine about 400 ft. (122 m.) west of the Minnie Healy shaft, which presumably originated, in one of the upper levels, from spontaneous combustion. The fire was walled off by concrete bulkheads and a pillar of ground 100 ft. (30 m.) thick was left below and mining resumed underneath. During subsequent operations, this pillar became cracked and broken and the fire passed into the new workings. It travelled downward and spread rapidly until, in 1917, it had become necessary to wall off portions of the Tramway, Leonard, and West Colusa mines on the 1300, 1400, 1500, 1600, 1800, 1900, and 2000-ft. levels, and the tops of the 2200-ft. raises were sealed. The fire area now consists roughly of a block 1000 by 1200 ft. and from the 600-ft. to the 2200-ft. level. This block is composed largely of a series of parallel northwest-southeast nearly vertical veins and stringers that form a large orebody, with no well-defined walls but badly fractured and faulted, and known locally as "horsetail ore." These veins, or orebodies, are mined by the square-set or the rill method.

Jan 1, 1923

By Masayuje Otagawa

The mining methods adopted in Japanese mines are less known to the mining world than those of other countries, owing to the geographical remoteness, but they present many features of interest to mining engineers. The Ashio copper mine is at the town of Ashio, in Tochigiken, about 109 mi. (175 km.) from Tokyo by the Imperial Government railroad. The area of the concession owned by the Furukawa Mining Co. is 5000 acres (5023 ha.). The mine was formerly divided into three, viz. Hon-ean, Kotaki, and Tsudo, which are distant 3 mi. (4.8 km.) from each other as shown in Fig. 1. However, in 1914, when the writer was general manager, the three mining plants were amalgamated into one with the result of simplifying the working projects and increasing the operating efficiency. The mine was visited by the Institute party in November, 1911, when K. Inouye was the general manager. Shortly afterward, the writer was appointed manager, and, in 1915, he was succeeded by Dr. K. Asano. At the end of 1917, K. Kibe became general manager and, after two years, was succeeded by the present manager, I. Sugimoto. For some time Dr. J. Kojima was acting general manager. It is necdless to say that the gentlemen mentioned are all members of the Institute, as is also Baron T. Furukawa, president of the company. Since the discovery of the enormous masses, called "kajika" or "bullhead" deposits, which the writer has described elsewhere,' the mining methods have been varied to meet the different conditions presented by these deposits. The Ashio Ore The country rock of this mine consists of the middle Chichibian slate and quartzite into which has been intruded a post-Tertiary plagio-liparite neck more than 2 mi. in diameter, in the shape of an inverted cone which narrows downward to a relatively small diameter in depth.

Jan 1, 1923

By R. M. Brick, M. A. Williamson

Certain features of the response of copper and brass to deformation and recrystallization remain obscure. The textures obtained on rolled sheet are listed by Schmid and Boas1 as: No adequate explanation has been advanced for the presence of the secondary deformation texture of copper and its absence in brass or for the origin of the cubic recrystallization texture of copper.2 A recent publication3 attempted to rationalize the above empirically described annealing texture of brass on the basis of retention of the (110) [112] rolling orientation plus twinning about the central octahedral poles of the usual secondary (110) [115] orientation. The difierence in the textures of annealed copper as compared to 70-30 brass is also shown by the difference in the position of ears for drawn copper, at o° and go", as compared with drawn brasses, at 45o, for all compositions between oo-10 and 70-30.4 Data on indi- vidual crystals are as yet too few to permit of an analysis of these textures comparable to that of mild steel as made by Barrett and Levenson.5 Experimental Methods The materials studied included copper specimens cut from the central, equiaxed crystal portion of a tough-pitch wirebar; brass made from this copper and high-purity (99.99 per cent) zinc including alloys of 7 per cent, 15 per cent, 24 per cent, 29 per cent and 36 per cent Zn and large single crystals of 70-30 bras. Sections 1/4 in. thick of the cast polycrystalline copper and brasses were reduced 40 per cent by rolling, recrystallized to a common grain size of 0.045 mm. and then rolled directly to foil 0.002 in. thick. Hardness readings employing both the Vickers and Rockwell machines were taken at intervals during the reduction. For comparison, similar specimens were cross-rolled—i.e., turned through 90° for each pass—and comparable hardness data were secured. Finally sections from the single crystals of brass were cut to obtain the following initial orientations; these sections were rolled, hardness data secured and a complete micrographic record of structural changes obtained.

Jan 1, 1941

By Raymond Wilson

Grinding costs are an important item in cement manufacture, and the cost of power is one of the large items in grinding costs. Even where power is of secondary importance, cost items dependent on mill capacity are influenced by the efficiency with which the mill uses power. Tube mills typify the grinding mills most generally used in cement plants, though other types are in use. Tube mills have been widely criticized as being extremely inefficient, and this feeling regarding them has led to many attempts to design more efficient grinding equipment. Other types may be an improvement over tube mills, but the improvement has certainly not been revolutionatry, at least as applied to clinker grinding. The very fact that there is doubt regarding the relative efficacy of various types of mills is an indication that an adequate basis for an analysis of performance is lacking. The development of methods of analyzing mill performance has been hampered by the lack of a suitable method for measuring the work actually done in pulverizing. There has been no acceptable standard to which mill performance might be compared. As a consequence, it was not known whether the margin of possible improvement in pulverizing operations was large or small. Even direct comparison of different types of mills was seldom possible because most plants had only one type of mill for each type of service. Comparisons between plants were difficult because of differences in the grinding characteristics of various clinkers. Some recent developments complete a chain of circumstances that place the cement industry in a particularly fortunate position for the study of its clinker-pulverizing operations. Modern investigators of grinding phenomena have generally agreed that the best measure of mill performance is the production of new surface. For most materials this measure of performance is largely theoretical and has a rather remote connection with the practical aims of the grinding operation. In clinker grinding, on the other hand, surface area is intimately connected with the properties conferred on the cement by grinding. Morcover, the determination of surface area is rapidly coming into routine use as a tost

Jan 1, 1938

By H. W. Hitzrot

The new 4800-ton fine-grinding plant at the Hollinger Consolidated Gold Mines property at Timmins, in the Porcupine district of northern Ontario, went into operation in November 1937, and represents the culmination of an experimental program. The plant is a moderately low rectangular building of hollow tile on a steel frame, large enough to house four 7 by 15-ft. ball mills, with a 12 by 27-ft. classifier beside each mill. At one end is space for the addition of another mill and classifier or a mill and classifier for the regrinding of table concentrates. This regrinding is now done in the old grinding department of the main mill building. Also within the new building are the four 6-in. sand pumps for lifting the product from the low-dis-charge ball mills up to the classifier feed launders and the containers and appurtenances of a complete dust-collecting system. Together with the usual overhead crane, these constitute the major units of equipment within the new plant. The location is at the lower end of the main mill buildings toward the old tailings pond, now so neatly leveled off and sodded to rival the very best of our own W.P.A. projects. Close by the new grinding plant is a large dome-shaped structure—the new fine-ore bin designed and built by Mr. Longmore and the Hollinger milling and engineering staffs. There are four separate automatically loaded inclined belt conveyors leading up from the bottom of the bin to the grinding plant. Each belt is equipped with a recording weightometer, in the grinding building. The whole structure and the machinery within it give the impression of permanence and a carefully integrated design with close attention to details, giving the operators every advantage for consistently good work. The many ideas and opinions behind this achievement were all ably organized and executed by the Hollinger milling and engineering staffs, and not a few were directly initiated by them. Excellent cooperation was afforded by the Hollinger staff to the engineers helping to conduct

Jan 1, 1939

By Frank R. Milliken, Robert Goodwin

In September 1937, the Ohio Copper Co. inaugurated the treatment of its copper-bearing mill tailings at Lark, Utah. These tailings had been accumulated during the regular operation of the Ohio Copper mine and mill over the period 1907 to 1919. Gravity concentration had been employed except for a comparatively short period in 1919, when flotation was used. The ore milled during that period assayed about I per cent Cu. The chief copper mineral, chalcocite, was disseminated in a shattered quartzite, mainly along fracture or cleavage planes. The quartzite gangue was extremely hard and grinding to liberation resulted in excessive sliming of the "sooty" chalcocite, with consequent high tailings losses. Recovery on the seven million tons treated was probably less than 60 per cent of the total copper content. As early as 1918, attempts had been made to sample the dump. In 1928, a complete sampling program was undertaken. The sampling consisted of seventy-four 5-in. post auger holes drilled to the full depth of the dump at regular intervals of 250 ft. Each 10-ft. portion thereof comprised a sample for analysis. Each sample was screened, rolled, divided into three parts, dried and assayed. The reject was retained for testing purposes. From the depth of the auger holes a contour map of the dump was plotted, Fig. I, which gives percentages of tonnage and copper content. The tonnage within the limit of the drill holes was estimated at about five million tons with an average content of 0.42 per cent Cu, 31 per cent of which (0.13 per cent) was acid-soluble. A screen analysis of the composite dump sample is shown in Table I. Flotation tests by several companies and individuals were then made, the results of which ranged from 62 to 74 per cent recovery. On the basis of these, a 200-ton pilot plant employing straight flotation was built and operated for a few months. Operation of this plant was unsuccessful, as no provision had been made to handle the copper-bearing solutions resulting from the water-soluble copper, a point that was overlooked in the laboratory test work. Attempts to decant the copper-bearing solution for precipitation in the usual manner ahead of flotation were not satisfactory because of low water recovery (owing to poor settling characteristics of the pulp) and contamination of the copper precipitate with unsettled slime. Low copper prices in 1931 necessitated the termination of testing. With the stimulus of higher copper prices in 1937, a review was made of metallurgical

Jan 1, 1943

By L. K. Welch, C.W. Macgregor

The past 20 years has seen a revolutionary change in the testing of materials at elevated temperatures. This has largely been brought about by the practical importance of the creep problem in the design of equipment for operation at high temperatures. The short-time tension test carried out at elevated temperatures has consequently assumed in many cases only a secondary role compared with the longtime creep test. In many problems, however, a knowledge of the short-time high-temperature properties of a metal is essential. To mention a few cases in which this is so, we might include all hot-forming operations such as rolling, forging, etc., the welding problem if residual stresses are to be computed, the development of new alloys for high-temperature service where, in the initial stages, time does not permit of long duration creep tests, and others. Usually a knowledge of the short-time properties is desired, if only to serve as a background against which to compare creep behavior. In conducting short-time high-temperature tests, it has been almost the universal practice to determine stresses based on the original area and strains referred to the original gauge length which is usually chosen as 2 in. It has been pointed out1,2 that one of the reasons that the true significance of certain tensile properties is not understood, which perhaps curtails their usefulness, especially when the material is applied under conditions differing considerably from the test conditions, is that true physical stresses and strains are not determined. It is essential to have a knowledge of true stresses and strains in order to correlate the values present in the tension test with those existing, for example, in hot metal-forming operations and in the general problem of the yielding and failure of metals under combined stress conditions. Stress and strain values based on the original dimensions of the test piece do not exist physically except in the early stages of the test. Since at the present time there is very little information in the literature on true stress-strain relations in the short-time high-temperature tension test it is proposed in the following pages to describe a

Jan 1, 1943

By F. M. Lewis, J. F. Myers

The paper reports the development of a large, slow speed ball mill closed circuited with a hvdro-scillator. This increased grinding efficiency 28 pct over conventional units. AS the title indicates, this is a progress report for the first year of experimental operation of a relatively large diameter, slow speed ball mill with 1-in. balls, with and without various classifiers, and including a hydroscillator. Several years ago the authors came to the conclusion that if any further progress were to be made in our flotation process, an understanding of the chemical and physical reactions and the control thereof, in the grinding circuit, was essential. It may be stated, at this point, that the preparation of a correct feed for the flotation process is still the number one objective of our grinding studies. This progress report deals with grinding "per se," and not with the chemical and physical reactions as the result of grinding. Prior to this time we had taken the naive position, that since grinding had been practiced by the industry for some fifty years or more, it had been well exploited and developed by a host of investigators. Consequently, we had given the matter only superficial attention. At the start of our study, we were aware of the fact that some difference in opinion existed, but we were not prepared for the controversial evidence that developed nor for the extent to which the experts differed in their viewpoints. There seemed nothing else to do but to tour the continent and decide for ourselves what was right and what was wrong, read all the published literature and visit with anyone who had ideas about the matter. This we did over the next few ensuing years. Since our study has met with some measure of success, we report, herewith, these data that ultimately they may be of help to other investigators. In 1944 it became necessary to increase our grinding capacity and at the same time to grind the sulphide portion a little finer. This provided the impetus to put our ideas into effect. As has been previously described, our grinding flowsheet at that time consisted of a 6x12 rod mill, followed by two 5x10 ft, and one 6x12 ft trunnion overflow ball mills, with conventional rake classifiers. Naturally, we first considered all the possibilities of altering or adding to the existing equipment. It became evident that if any appreciable increase in grinding efficiency could be obtained, it would pay to scrap the existing small mills and classifiers and install one big mill with adequate classification. Trying to determine just how much more efficient a big mill could be, in which were incorporated all

Jan 1, 1951

By John R. Spencer

A capillary tube variable volume cell is described, which has operated satisfactorily over a range of 100°F and 3,500 psi to 550°F and 1,500 psi. The cell contents are entirely visible over the length of the capillary with the exception of a space at the top amounting to three per cent of the total volume. Observations on the critical behavior of simple systems have been greatly facilitated by the apparatus, it being possible to establish the critical conditions for a particular mixture in the course of a day's run. INTRODUCTION Many types of apparatus have been designed for obtaining data on the phase relationships of hydrocarbon systems. Such apparatus can in general be subdivided into two classifications; (l), indirect measurement of phase volume, and (2), direct visual observation of phase volume, each of which has outstanding advantages and disadvantages. Indirect measurement of phase volume requires the use of rather elaborate apparatus including internal probes in which are located the device for determining the locus of the interface between phases. Such equipment is by its very nature costly, and is complex from the standpoint of operating technique. Probing techniques can be used, however, over wide ranges of temperature and pressure with a high degree of reproducibility. Apparatus for visual observation of phase behavior obviously has the advantage of enabling the experimenter to see exactly what takes place, but because the material to be tested is contained in a cell constructed of both metal and glass, is limited severely as to the temperature range of operation. Furthermore. the maximum pressure usually is limited by the choice of material used for sealing the glass to the metal, and by the strength of the glass itself. In the interest of increased efficiency of observation, as much of the cell as possible should be visible to the eye. Glass capillary tubes have been used successfully but have always given difficulty at the metal-to-glass seal. An apparatus has been devised to overcome the problems of sealing and resistance to temperature effects that have heretofore been the limiting factor with glass apparatus in the observation of phase volumes at elevated temperature and pressure. APPARATUS The objective which dictated the general arrangement of the apparatus (Figs. 1 and 2) was simplicity of operation. The air bath, A, was constructed of an iron framework to which was attached approximately one inch of glass wool bats which were covered on the outside with "Masonite." A roughly octagonal center piece was installed to provide forced circulation of the air by the fan, B, past the heaters, D, cell, F, and thermoregulator, C, respectively. The entire top of the box is removable to facilitate charging of the cell and to permit easy maintenance. Two windows are provided before and behind the cell to allow the operator to observe the contents against the background fluorescent light, E. The heaters,

Jan 1, 1951

By John T. Norton

In recent years, the damping capacity of metals has come to be recognized as an important index of certain types of structural change. In a number of instances, this property has proved to be particularly sensitive, but insufficient work has been done to permit a general interpretation. There is considerable question at the present time as to just what factors are responsible for the internal dissipation of energy when a metal is carried through a cycle of stress, and these factors must be ascertained if the value of the damping method as a metallurgical tool is to be determined. Since internal stresses are among the chief causes of dissipation of internal energy, or damping capacity, it was thought that a study of the changes in damping during the recovery and recrystalliza-tion of a cold-worked metal might throw some light upon the subject, particularly if the damping changes were correlated with other properties that are better understood. Probably more work has been done on the recrystallization phenomena of alpha brass than on any other metal, so this was chosen as the material for the present investigation. Damping measurements on brass have been made by Förster and Köster.1 They showed that the annealing of a brass that had been cold-drawn to 50 per cent reduction produced a rapid fall in the damping, a flat minimum occurring at approximately the temperature of recrystallization. The damping remained at a low value until grain growth was well under way and then it increased rapidly with increasing grain size. Köster and Rosenthal2 continued the work in greater detail. They pointed out that the damping decrease does not correspond to the hardness drop but occurs at a lower temperature, suggesting that the relief or redistribution of internal stresses has a large effect while the actual recrystallization effect is small. They also show the increase in damping at the higher annealing temperatures. Their curves are reproduced in Fig. 1.

Jan 1, 1940

By George Espey, George Sachs, G. B. Kasik

IT has been reported frequently that the hardness and strength vary over the cross section of cold-worked, particularly cold-drawn, material. Brass rod and wire usually have been found to possess a maximum strength and hardness near the surface.1,2 According to Sachs,' the center fiber has about the same strength as a wire stretched by the same amount in a tensile-test machine, the strength increasing toward the surface (Fig. I). These differences are particularly large for wire given a small reduction on drawing through a die with a wide opening. However, with increasing reduction and hardness, a tendency to form a thin soft surface skin becomes apparent. On the contrary, copper wire has usually been found to possess a soft surface skin3-5 and it has been reported by Harris3 that during the cold-drawing of hot-rolled wire the surface layer becomes increasingly softer than the core, while the layer of maximum strength moves toward the core, it being found near the surface at first. The increase of strength and hardness from the core to the skin is readily explained by the observation that, in addition to the stretching, the layers of a rod or wire are sheared more the closer they are to the surface.1,6-8 However, the presence of a soft surface layer can be attributed only to an annealing effect. The source of such a softening might be the extremely high temperature that originates from the friction between

Jan 1, 1942

By Michael B. Bever, Carl F. Floe

The solubility of hydrogen in molten copper-tin alloys is of both practical and theoretical interest. From a practical standpoint, data on the equilibrium solubility as a function of temperature, pressure and alloy composition are valuable for a better understanding of porosity problems in bronze castings. From the theoretical point of view the determination of the hydrogen-copper-tin equilibrium is of interest since it extends the laws governing the solution of gases in metals. This paper presents the results of an investigation of the solubility of hydrogen in representative compositions of the copper-tin system at temperatures ranging from above the liquidus to I300°C. and at pressures from less than 50 mm. of mercury to about atmospheric. Review of Previous Work The solubility of hydrogen in copper was determined by Sieverts and Krumbhaarl in 1910 and by Roentgen and Moeller2 in 1934. Their values are in fair agreement. In 1926 Iwasé3 reported results that were very much higher. The published data on the solubility of hydrogen in tin do not agree. Smithells4 states that no reliable data are available According to Sieverts and Krumbhaar,5 hydrogen is insoluble in tin. Bircumshaw,6 on the other hand, found a definite solubility at 800°C. The latter's experimental procedure did not provide for stirring of the metal and in his opinion he failed to reach equilibrium. Iwasé3 again reported large solubility values. For copper alloys, Sieverts and Krumbhaar5 distinguished between alloying elements that do not markedly affect the solubility of hydrogen, elements that increase the solubility, and elements that reduce it. They named gold, tin, and aluminum as examples of this last group and reported hydrogen solubility data at 1225°C. for the copper-rich side of these alloy systems at atmospheric pressure. Without giving experimental results, they stated that the amount of hydrogen dissolved by liquid copper alloys is proportional to the square root of the pressure as in pure metals. These authors suggested that in a limited way the effect of an alloying element on the solubility of a gas is related to the constitution diagram for the alloy system. Sieverts7 also called attention to the fact that the curve of hydrogen solubility versus composition of copper-tin alloys shows a sharp change of direction at the composition of Cu3Sn and suggested that this compound persists at least to some extent in the molten state. Iwasé3 reported large hydrogen solubility values for several compositions of copper-tin alloys, which appear to be in error.

Jan 1, 1944

By W. M. Rust, W. D, D. W. Mounce

The almost universal acceptance of electrical logging by the petroleum industry calls for a critical examination of the physical bases of the common methods. This is particularly needed for the natural potential log. The conventional explanations are based on the phenomena of electrofiltration and electro-osmosis. However, experimental data show that they fail to give a basis that is quantitatively sound. Moreover, they lead to interpretations of details of electrical logs that are erroneous. It was found experimentally that when a plug of shale is placed in a chain of dissimilar electrolytes, a current flow results. Experiments on oil-well cores and fluids similar to those existing in wells show that potentials are set up which are in reasonable agreement with those encountered in electrical logging. Doubtless other sources of potential are important but this explanation not only accounts for much of the potential but also clarifies some fairly familiar examples of misinterpretations. Introduction The extraordinary value of electrical well logging as a tool for petroleum engineers and geologists is now so uni- versally recognized that it is not necessary to point out the ways in which it can be useful. It is sufficient to mention only the saving that has resulted from the elimination of much coring that would have been necessary under former practices and the considerable additions to reserves resulting from the discovery of sands missed in coring. Paradoxically, the very remarkable success that has resulted from the application of electrical logging to correlation and completion problems has cost some of its most consistent users dearly.' The fact that some operators have placed unwarranted faith in erroneous interpretations of electrical logs does not reduce the value of the logs. It should, however, make one pause long enough to ask why experienced users should be misled. The answer to this question is not hard to find. In nearly every case, the fault has been oversimplification. This is illustrated very aptly by the familiar interpretation and theory of the natural potential log. Recording and Interpreting Logs The natural potential log is extremely simple to record precisely enough for all present-day uses. One needs only an electrode, a cable to lower the electrode through the drilling mud, a recording meter and a surface ground connection. The electrode can be elaborate but need not be. A simple brass rod 2 in, in diameter and 2 or 3 in. long is quite satisfactory. The cable need not be particularly well insulated, nor need it have a very low resistance. The recorder can be a vacuum-tube 1 References are at the end of the paper.

Jan 1, 1944

By L. S. Reid, R. L. Huntington, Chen Chun Ku

The simultaneous adsorption of water and hydrocarbon vapor from natural gas by three grades of alumina has been studied at atmospheric pressure and temperature. Results of this investigation reveal that the presence of water vapor in the gas inhibits the adsorption of hydrocarbon vapor, although the presence of the latter does not have a pronounced effect upon the adsorption of water vapor. Adsorption of water-hydrocarbon mixtures from gas is divided into three phases. In the first, both water and hydrocarbon vapor are adsorbed; in the second, adsorption of water vapor proceeds while desorption of hydrocarbon takes place; in the third phase, the adsorbyt approaches complete saturation with respect to both water and hydrocarbon vapors. Both theory and experimental data can be applied to design and operation of commercial dehydration plants, and an illustration is presented. Introduction Dehydration of natural gas becomes increasingly important as the operating pressures employed in gas processing and transmission are increased above 500 ib. per sq. in. Gas produced from high-pressure wells is saturated with water vapor when it leaves the reservoir and it continues into the processing plant or transmission system in a saturated condition because of the substantial decrease in temperature due to expansion at the wellhead. Usually this gas is accompanied by liquid water and hydrocarbons that have condensed with the change in temperature and pressure. Without dehydration, gas temperatures must be held at relatively high levels to prevent solidification of gas hydrates. According to Hammerschmidt's data8 on the relationship of pressure to the freezing point of natural-gas hydrates, the minimum safe operating temperatures range from 55' to go°F. for pressures ranging from 500 to 3000 lb. per sq. in., respectively. Often it is difficult to maintain gas temperatures above the hydrate-freezing temperature because of climatic conditions, unless flow-line heaters are installed. Also, in processing gas for its gasoline content at high pressures, it is desirable to employ operating temperatures lower than the hydrate-freezing point. In distributing high-pressure gas, the large pressure drop from line pressure to town-gate pressure often prbduces sufficient cooling to freeze the regulators and disrupt consumer service. Therefore, it is highly essential to dehydrate high-pressure natural gas if smooth and economical operation is to be maintained at all times. Few published data are available on the simultaneous adsorption of water and hydrocarbon vapors. The literature contains many mathematical expressions for rate of adsorption in various systems but a rational correlation of the existing rate

Jan 1, 1944

By H. K. Livingston

A technique has been developed which makes it possible to determine the spreading pressure of liquids and solids, for simple systems. Data for surface tensions, interfacial tensions, spreading pressures, and contact angles for water, heptane, and silica are tabulated.' These results can be applied to the evaluation of capillary rise and displacement pressure in a petroleum reservoir. Appropriate equations are presented and the application of these equations is discussed. The presence of surface-active components affects both capillary rise and displacement pressure and also seems to influence the rate of fluid flow. The purpose of this paper is to supplement and bring up to date the last article on the subject of the surface chemistry of petroleum reservoirs, that of Garrison in the 1935 Oil and Gas Journa1.1 A discussion of the "adhesion tension" concept used by Garrison has been presented in another publication,2 together with the reasons for the recommendation that the term "adhesion tension" be abandoned. In view of the fact that some of the data used by Garrison have been superseded by more recent work, it seemed advisable to call attention to this fact and present the more important data currently believed to be correct. In the earlier paper, Garrison set up the equations that 'relate solid-oil and solid-water interfacial tensions to each other, and applied data from Bartell and Miller3 to these equations. However the adhesion tension measurements made by Bartell and Miller involved a confusion of symbols, so that they did not actually measure the spreading pressure, ?s — ?sf.2 The spreading pressure is a convenient method of indicating the amount by which the surface energy of a solid surface is lowered on immersion in a liquid or vapor. Since the initial value of the free surface energy is represented by the symbol ?s and the final value is ?sF, the spreading pressure is ?s — ?SF. A technique has now been developed4 that makes possible the determination of ?s — ?sF for simple systems. This method would be very difficult to carry out with a multicomponent system such as exists in the petroleum reservoir. However, already results have been obtained for ?s — ?sF for water and heptane in contact with silica and graphite. These values will be of the same order of magnitude as those in the petroleum reservoir. Accordingly, it is possible for the first time to discuss the surface-energy relations of the petroleum reservoir on a semi-quantitative basis. Preliminary Generalizations A petroleum reservoir may contain the following four phases: gas, hydrocarbon liquid, aqueous liquid, and solid. The three fluid phases are dispersed through the solid reservoir rock. If gravity were the only force acting, it is obvious that the

Jan 1, 1943