Search Documents

By E. L. Kinsella, F. S. White

Solids fluidization utilized in two ways for the commercial production of lime is described. Crushed —6 mesh limestone is dried and dedusted in a single bed reactor, then calcined in a 5-stage reactor. Construction, operation, and results obtained with both processes are given. THE solids fluidization process brought out by the Standard Oil Development Co. in the early forties for catalytic cracking of petroleum enabled rapid transfer of large quantities of heat from gases to solids under closely controlled temperature conditions. As the technique developed, it was natural that applications for the process outside the petroleum industry would be sought. The calcination of limestone to quicklime requires the transfer of a large quantity of heat at high and closely controlled temperatures. For these reasons, this possible application was one of the first to be investigated. Laboratory work conducted by the Dorr Co. indicated that lime produced by solids fluidization would be of exceptional quality. Calculation of theoretical heat balances showed that savings in fuel could be expected. Accordingly, a pilot plant of 10 tons per day capacity was erected by the New England Lime Co. at Adams, Mass., to substantiate the process. Operation of the pilot plant, previously described,' showed that excellent lime could be produced with a saving in fuel. The work also indicated the necessity of preparing feed to remove the finer fractions if dust losses were to be held to a tolerable level. A single-stage fluidized solids drier-stripper was developed to accomplish this sizing.' Subsequently a commercial lime reactor was erected at Adams, beginning operation in June 1949, followed by air sizer facilities completed in November 1951. This paper will describe these two applications of solids fluidization. The raw material for preparation of lime by the fluidizing process is a high calcium crystalline lime- stone having the approximate chemical composition shown in Table I. The stone is first prepared by crushing and grinding in conventional equipment to pass a 6-mesh sieve. After crushing, the material is sent to the FluoDry unit for drying and dedusting. Fluidized Drying and Sizing As shown in Fig. 1, the FluoDry unit consists of a -in. cylindrical steel shell, 9-ft ID by 22-ft 6-in. overall height. Attached horizontallv at the bottom is a 6-ft diam combustion chamber, approximately 7 ft 6 in. long. A refractory constriction dome, consisting of first-quality fire brick shapes, partitions the inside into two sections. The lower section is called the windbox and the upper the bed compartment. The vertical wall of the shell is lined with 6-in. first-quality rotary kiln blocks. In the bottom of the windbox a hoppered section is formed with castable refractory to permit the windbox to be readily cleaned via a 6-in. screw conveyor. The combustion chamber is similarly lined with refractory shapes. On the 6-in. diam section, 4 in. of insulating brick, HW-26, are used. The inner combustion chamber is lined with 4-in. Korundal brick to withstand the high flame temperatures encountered. An 8-in. steel feed pipe, entering vertically through the top and fitted with an air-operated cone valve,

Jan 1, 1953

By F. S. White, E. L. Kinsella

Solids fluidization utilized in two ways for the commercial production of lime is described. Crushed —6 mesh limestone is dried and dedusted in a single bed reactor, then calcined in a 5-stage reactor. Construction, operation, and results obtained with both processes are given. THE solids fluidization process brought out by the Standard Oil Development Co. in the early forties for catalytic cracking of petroleum enabled rapid transfer of large quantities of heat from gases to solids under closely controlled temperature conditions. As the technique developed, it was natural that applications for the process outside the petroleum industry would be sought. The calcination of limestone to quicklime requires the transfer of a large quantity of heat at high and closely controlled temperatures. For these reasons, this possible application was one of the first to be investigated. Laboratory work conducted by the Dorr Co. indicated that lime produced by solids fluidization would be of exceptional quality. Calculation of theoretical heat balances showed that savings in fuel could be expected. Accordingly, a pilot plant of 10 tons per day capacity was erected by the New England Lime Co. at Adams, Mass., to substantiate the process. Operation of the pilot plant, previously described,' showed that excellent lime could be produced with a saving in fuel. The work also indicated the necessity of preparing feed to remove the finer fractions if dust losses were to be held to a tolerable level. A single-stage fluidized solids drier-stripper was developed to accomplish this sizing.' Subsequently a commercial lime reactor was erected at Adams, beginning operation in June 1949, followed by air sizer facilities completed in November 1951. This paper will describe these two applications of solids fluidization. The raw material for preparation of lime by the fluidizing process is a high calcium crystalline lime- stone having the approximate chemical composition shown in Table I. The stone is first prepared by crushing and grinding in conventional equipment to pass a 6-mesh sieve. After crushing, the material is sent to the FluoDry unit for drying and dedusting. Fluidized Drying and Sizing As shown in Fig. 1, the FluoDry unit consists of a -in. cylindrical steel shell, 9-ft ID by 22-ft 6-in. overall height. Attached horizontallv at the bottom is a 6-ft diam combustion chamber, approximately 7 ft 6 in. long. A refractory constriction dome, consisting of first-quality fire brick shapes, partitions the inside into two sections. The lower section is called the windbox and the upper the bed compartment. The vertical wall of the shell is lined with 6-in. first-quality rotary kiln blocks. In the bottom of the windbox a hoppered section is formed with castable refractory to permit the windbox to be readily cleaned via a 6-in. screw conveyor. The combustion chamber is similarly lined with refractory shapes. On the 6-in. diam section, 4 in. of insulating brick, HW-26, are used. The inner combustion chamber is lined with 4-in. Korundal brick to withstand the high flame temperatures encountered. An 8-in. steel feed pipe, entering vertically through the top and fitted with an air-operated cone valve,

Jan 1, 1953

By AIME AIME

THE 129th meeting of the American Institute of Mining and Metallurgical Engineers convened at New York City, in the Engineering Societies Building, Feb. 18-20, 1924. On February 21 an excursion was made to the Bethlehem Steel Co., at Bethlehem, where about 200 members and guests were splendidly entertained. An illustrated description of the Bethlehem Plant will be published next month. The meeting and excursion were largely attended; the registration at New York totalled 1276 versus 1201 in 1923. William Kelly, long identified with the iron-mining industry of the Lake Superior district, was elected President of the A. I. M. E. for the coming year, at ,the annual business meeting, Feb. 19, succeeding E. P. Mathewson. The following Directors were also elected (the date signifies year of termination of office; the final figure indicates the "District" the Director represents).

Jan 1, 1924

By E. W. Davis

I . OPERATING TESTS 1. CHARACTER OF ORE UNDER INVESTIGATION On the eastern end of the Mesabi Range, in Northern Minnesota, is a large formation of siliceous rock which contains bands and fine grains of magnetite . The magnetite comprises about 35 per cent. of the rock. Fig.. 1 show's graphically that the tonnage of minus 200-mesh material produced varies directly with the tonnage fed to the mill. There is undoubtedly some limit to this relation, but there seems to be no indication of it at 18 T. per hr. Some of the conclusions drawn from this test are that: (a) The ball-mill is naturally a machine of very large capacity; (b) if it is not possible to deliver a large tonnage of original feed to the mill, a closed circuit should be provided so that the mill may crush its own oversize.

Jan 2, 1919

By Edward Walsh

In the early history of the production of metallic iron from the native oxides or ores, success attended the labors of the workman according to the care he devoted to his work, and according to the degree of skill he possessed in furnishing the required amounts of fuel and ores to be acted upon by the blast propelled by the bellows, trompe, or wooden tub, and delivered into the hearths of the Persian, bloomery, or Catalan forges. The same skill may also have been of avail in the use of the lower forms of the ".Stück," "Blue,"or" Wolf"

Jan 1, 1887

By P. W. Bridgman

DURING the war, the Navy undertook the construction, under my direction, of an experimental gun embodying features designed to lessen the cost and time of production. These experiments were initiated after representations as to their, desirability had been offered by myself, by the Naval Consulting Board, and by the National Research Council. The first drawings were made in June, 1917, and the experiment was completed in November, 1918. For the sake of clearness it will pay to recapitulate briefly the fundamental idea of gun construction. It is well known that if a hollow cylinder is subjected to internal fluid pressure, the maximum stress occurs in the inside layers, the outer parts carrying much less than their due share of the stress. This inequality of stress is more pronounced the thicker the walls of the cylinder. If such a cylinder is pushed to the elastic limit, failure in elasticity will take place long before the outer layers have reached the limit of their capacity. Economical use of the material would demand, however, that all parts of the cylinder reach the limits of their capacity simultaneously. This may be brought about, at least in cylinders of not too great thickness, by producing in. the inner layers an initial compression, and in the outer layers an initial tension. The effect of internal pressure is at, first to relieve the compression of the inside layers, while increasing the tension of the outside layers. If the initial stresses are properly distributed, all parts of the cylinder will reach their elastic limits simultaneously, thus giving a cylinder of maximum strength for its weight. In gun construction as hitherto practiced, this initial distribution of stress is produced either by winding the inner tube with wire, a common English practice, or by shrinking hoops over the inner tube, which has been the standard American practice. Either process is long and expensive, particularly with the larger guns, 12- or 14-in., which require

Jan 2, 1920

By T. H. Aldrich

The Aldrich Mining Go. holds under lease from the Illinois Central R. R. Co. about 14,000 acres, in the east half of Township 12, Range 12 W., in Marion county, Alabama, and owns other lands, of which about 1,000 acres adjoin this leased tract, making a total area of about 15,000 acres, all of which is underlain by the coal-seam upon which the company is operating. This seam is nearly horizontal; and a ravine, diagonally crossing the tract, exposes the outcrop on either side for about 2 miles. The territory has been so divided that nearly the whole of it can be worked out by two collieries. The mines at Brilliant were opened in the fall of 1898, and shipments began in the following spring. The original plan was to furnish steam-coal for locomotives to the Illinois Central R. R. Co.; and upon this expectation the investment of capital was made. The field was entirely new; and the softness of the coal at the outcrop induced the belief that it could be very cheaply mined. A contract for the delivery of a large quantity of coal to the railroad was accordingly executed. But with the advance of' the entries to increasing distances from the outcrop, the coal proved so hard that it could no longer be drilled with a breast-auger; and the expense of mining became so great that the contract for cheap steam-coal had to be canceled. It became evident that the work must be done with machinery and explosives, if it could be profitably done at all. On the other hand, the excellent quality of this coal opened, at the same time, a possible market not specially contemplated at the outset—namely, that of a first-rate coal for domestic and general uses. Since no other deposit of such coal was known to exist on the line of the Illinois Central, or any other railroad

Jan 1, 1907

By D. J. Reed

Concord coal mine near Bessemer, Ala., built, owned, and operated by Tennessee Coal & Iron Div., U. S. Steel Corp., produces only a metallurgical grade for use as coke in blast furnaces of the division at the Fairfield and Ensley works. Capacity of the operation is approximately 800 tph, half of which is delivered to the coke and coal chemical plant at Fairfield after beneficiation to metallurgical grade coal. The remaining portion of the mine run is rock and refuse removed during preparation. Concord mine coal is hoisted to the surface coal preparation plant by an underground slope conveyor. The slope conveyor is 2449 ft long and has a lift of 729 ft. At time of installation the Concord mine slope conveyor was the largest single conveyor unit ever made with respect to belt horsepower and total lift. After several years it became necessary to determine the cause of slope conveyor cover wear.

Nov 1, 1956

By George Kunz

(Butte Meeting, August, 1913.) . THE manifold inconveniences resulting from the absence of a uniform standard of mass for determining the weight of precious stones have long been obvious. This lack has been keenly felt in commercial transactions, and those who have devoted time and research to the study of historic diamonds and precious stones have had frequent occasion to deplore the absence of such a standard in the past. In a paper read in Chicago in 1893, before the International Congress of Weights and Measures, held in connection with the World's Columbian Exposition, the writer suggested dividing the carat into 100 parts, and constituting a standard international carat of 200 mg. ; that is, 5 diamond carats or 20 pearl grains to a French gram, making 5,000 carats or 20,000 pearl grains to a kilogram. He also called attention to the fact. that while this would depreciate the present diamond carat or pearl grain only about 2.5 per cent., it-would abolish the troublesome discrepancies between the various carat-weights now in use, and could be easily explained and understood everywhere.1 The subject of the various diamond carats, their incongruity, and the resulting confusion as to the correct. weights of historic gems when definite records of them are searched for, has been fully treated by me in an extensive study of this subject in The Book of the Pearl.2 To the earnest and unremitting efforts of C. E. Guillaume, Director of the Bureau Internationale des Poids et Mesures at Sèvres, is largely due the eventual success of this eminently desirable reform, which he has constantly urged both by articles on the subject and by addresses delivered in Paris before the International Committee for Weights and Measures.2

Jan 7, 1913

Jan 1, 1969

Mining and oil industry representatives are scheduled to testify May 15 at hearings on the Simpson bill to extend the Reciprocal Trade Agreements Act, Several Congressmen have introduced bills to extend present trade agreements without modification. Price of copper appears to be stabilizing at 30[] per lb, after a period where market price ranged from 27 to 34[]. Copper offerings from abroad were finding no takers at 30.24[] per lb late in April.

Jan 5, 1953

By Joseph Hartshorne

EVER since the introduction of the Siemens regenerative furnace, it has been recognized that a certain amount of gas is lost each time the furnace-action is reversed. This loss comes, first, from the gas which passes through the free connection between the stack and the gas-main, which exists during the time the reversing-valve is turning over; and, secondly, from the gas which is in the chamber and flues, from the hearth to the reversing-valve, and which flows back into the stack when the valve is reversed. The amount lost each time is, of course, small; but, since a furnace is reversed from four to six times every hour for, say, 300 days in the year, the aggregate is large enough to be well worth attention. The estimate has been published' that, in Germany alone, the loss from the first of the above causes amounts to 500,000 marks per year. The loss from the second cause is, of course, much greater. A process for saving this entire loss, in use at Teplitz, Bohemia, for about three years, would seem to be of value even in this country, where coal is cheaper and where the small economies are not watched as closely as they are in Europe. This process, invented by Mr. Adelbert Kurzwernhart, late Technical Director of the Teplitzer Walzwerk, has been worked out with thoroughness. The loss from each cause can be calculated very closely for any particular furnace, and the results to be expected from the process ascertained. It can easily be decided, therefore, whether it is worthwhile to adopt it under any given conditions. The amount of chamber-gas lost depends upon,-(1), the cubic contents of the chamber, ports and flues upon one side of the furnace, up to the reversing-valve (deducting, of course,

Mar 1, 1906

By J. Q. Ehrgott

INTRODUCTION The U. S. Army Engineer Waterways Experiment Station (WES), under sponsorship of the Defense Atomic Support Agency, has recently developed a unique dynamic high-pressure triaxial testing device (DHT). The device permits acquisition of both axial and lateral deformation data while undisturbed soil and/or rock specimens are subjected to various states of controlled impulsive-type stresses produced by varying both the axial stress and the radial stress rapidly with time. The device is used to develop controlled dynamic pressure pulses within the triaxial chamber fluid on soil or rock test specimens to 3 inches in diameter. Controlled dynamic axial pulse loads are delivered to the specimen by a piston driven by an existing pneumatic ram loader (SECO). The DHT consists of a triaxial cell and a pressure supply and decay system which permits the chamber pressure to be varied with time. Together the DHT and SECO operate in a testing program so as to provide time varying confining pressures and axial loads to test specimens at independently controlled but synchronized programmed rise, hold, and decay times. Rise time is defined as the time from zero load or pressure to peak load or pressure; hold time is the time of constant peak load or pressure; and the decay time is the time from peak load or pressure to zero load or pressure. The maximum dynamic confining pressure attainable is approximately 15,000 psi and the fastest rise and decay times are 3 millisecond (msec) and 20 msec, respectively. This paper presents a description of the DHT, the necessary support equipment, and details of the measurement system. Performance evaluation tests conducted on clay siltstone and a Cretaceous sandstone are presented since the results demonstrate some of the capabilities of the device and show some of its characteristics.

Jan 1, 1971

By T. R. Wright

THE Corporation operates concentrators in four camps: Casapalca. Morococha, Cerro de Pa-co, and Mahr. The present concentrator at Cerro de Pasco is the newest having been completed in 1943. and that at Casapalca the oldest, having been built originally as a gravity concentrator, in 1889. Prior to 1925 the Corporation's milling operations were confined to the beneficiation of silver-bearing copper ores, and treatment of these ore: by flotation was started in 1918. Although fairly large deposits of complex, fine-grained lead-zinc ores existed, little progress had been made in the treatment of such ores--in Peru or elsewhere-until the early 'twentics. The Casapalca concentrator began the selettive concentration of complex leadzinc ores by all-flotation methods in 1925, or contemporaneously with the commercial development of selective lead-zinc flotation in the United State:.

Jan 1, 1945

By Jack M. Swales

Kermac Potash Co., the newest American entry in a rapidly expanding industry, has come on the scene with notable variations in conventional shaft-sinking and mining techniques. Located in the famed potash producing district east of Carlsbad, N. Mex., Kermac started up its mine in November, 1965, to supply ore to the company's 500,000-tpy potash crystallization refinery. In so doing, the company (1) drilled the first large diameter mine shaft in the potash industry and (2) has employed new continuous miners especially adapted for use in thin potash beds. REACHING THE ORE ZONE In its initial mine planning, Kermac, a partnership owned jointly by Kerr-McGee Corp. and the National Farmers Union Development Corp., considered it imperative that the shafts be sunk and equipped as soon as possible and that the mine be developed sufficiently to insure a constant ore feed to the mill when the unit was placed on stream. After examining the alternative sinking techniques available to it, the company decided to accept a proposal by Big Hole Drillers, Inc., to drill the shaft from the surface through various formations of sandstones, siltstone, shales, anhydrite, limestones, dolomite and salts to the potash ore zone.

Jan 12, 1966

Jan 1, 1966

Jan 1, 1967

By Charles M. Means

A thoroughly modern coal-handling system has been installed at the Pittsburgh Terminal H. H. &. Coal Co.'s new No. 8 shaft, or Cover-dale mine, about 11 mi. (17.7 km.) from Pittsburgh on a spur of the Montour R. R. The Pittsburgh scam, which is the one worked, is reached at a depth of 342 ft. (104 m.). Power is delivered to the mine at 22,000 volts over a transmission line of the bow-arrow type of construction. A private telephone line connecting the various mines and the main office in Pittsburgh is carried on the same poles. The high-tension line is brought to an outdoor, step-down, transformer substation, where three 833-kv.-a., single-phase, 60-cycle, oil-insulated, self-cooled transformers reduce the potential to 2300 volts. The transformers are protected by electrolytic, aluminum-cell lightning arresters, horn gaps, and choke coils. High and low-tension busses, together with fuses, choke coils and air-break horn-gap switches with thcir remote-control operating mechanism are mounted on a substantial structural-steel tower 25 ft. (7.6 m.) in height. Mine Substation The transformer substation is adjacent to a. pressed-brick building that houses direct-current substation equipment together with switchboards, etc., for the control and distribution of power. This building also contains the hoist for the men and supplies. Main Switchboard The 2300-volt circuit is carried underground in a conduit from the transformer substation to an oil switch in the substation and supply hoist building. This is the main switch controlling the 2300-volt busbars mounted back to a twelve-panel black-slate switchboard. From the switchboard, 2300-volt circuits are carried to transformers feeding the street and house lighting systems and to other transformers furnishing power for the elevator and lighting circuits in the store building. Other 2300-volt circuits run from this switchboard to the main hoist building, fan house and auxiliary or man-and-supply hoist. High-tension wiring,

Jan 1, 1922

By C. H. Benedict

Largest and most important of the milling plants under construction during the year is the Morenci plant of the Phelps Dodge Corp., in Arizona, where plans are being rushed for production in 1942. Grate mills will be used for fine-grinding, and in the pilot plant, classifiers of the spiral type have the preference for the closed- circuit work. The flotation units will be chiefly of the pneumatic type, with some mechanical units as auxiliaries. The Fagergren, Pan American, and Agitair machines were left in the competition as the year closed. If the absence of European markets for finished products has dislocated the mining industry, fortunately the lack of raw materials required in the beneficiation of ores has not been serious. except possibly as to the inability to import flint grinding pebbles. Some of the less important gold mines still use pebbles for grinding as is also the practice in the comminution of nonmetallics used in various industries. T the Calumet & Hecla in the Lake A Superior copper district pebbles have been used exclusively in open- circuit grinding in the Hardinge mills treating the

Jan 1, 1941