Search Documents

By John Crawford

MUCH has been written of late regarding the flotation of coal as a means of reclaiming the valuable portion of the fines encountered in nearly all methods of coal preparation. Whether the process be wet or dry, whether the dust be sent through the entire process or removed prior to the cleaning by some such method as screening or aspiration, one of the final products consists of a considerable proportion of -48-mesh material. The percentage of this -48-mesh material depends upon the mining method, transportation, storage, and method of preparation. The ton-nage of this dust material ranges from 1 to 10 per cent of the total output of the cleaning plants. Four methods of disposal are available for this coal: 1. Disposal with the refuse from the plant. 2. Addition, after being reclaimed from the wash water, or dust collectors, without cleaning to the larger sizes. 3. Separate disposal as a pulverized fuel. 4. Cleaning so that addition to the larger sizes benefits the product as a whole. It is also true that flotation in one form or another is the only known way to effectively clean this material. While some processes do a reason-able cleaning job down to and including +100 mesh, by far the greater-majority stop at or short of the +48-mesh size.

Jan 1, 1935

Commonwealth of Pennsylvania, Department of Internal Affairs, Topographic and Geologic Survey, Harrisburg, Pa George H. Ashley, State Geologist All available printed Bulletins may be obtained through the Commonwealth of Pennsylvania, Division of Documents. Where a price has been set on the publication, checks should be made out to the Commonwealth of Pennsylvania. A Syllabus of Pennsylvania Geology and Mineral Resources has recently been published by the Survey as Bulletin G1, and consists of a general survey of the state An appendix of this bulletin also gives a complete bibliography of Survey publications It will be sent upon request. The State Geological Survey has gone through several phases and reorganizations, publications of three of them being numerous and important A fire, in 1927, destroyed supplies of many of the papers of the present Survey. Available bulletins of the present Survey are: Bulletin M6: Bituminous coal fields of Pennsylvania, in 4 parts available as follows: pt 1, General description of coal, 50 cents; 3, Bituminous coal resources, 25 cents, 4, Analyses of bituminous coals, 25 cents Bulletin M10, Fire clays of Pennsylvania; Mll, Molding sands of Pennsylvania; M12, Anthracite culm and silt (1928); M13, Feldspar in Pennsylvania; M14, Magnetite deposits of French Creek (1931); County Report C1, Adams County, pt 1, Geology and geography (in press), County Report C2, Geology and mineral resources of Greene County (in press); Topographic and Geologic Atlas A5, New Castle Quadrangle (1929), $1; Topographic and Geologic Atlas A27, Pittsburgh Quadrangle (1929), $1; Topographic and Geologic Atlas A168, Lancaster Quadrangle (1930), $1. The present Survey has also issued a number of short mimeo¬graphed bulletins any of which will be sent upon request Briefly they are: No. 15, Mineral resources of Pennsylvania; 20, Iron ores; 28, Magnesite; 40, White clay deposits, Monroe County; 45, White clay deposits, central Pennsylvania; 47, Manganese, Eastern Pennsylvania, 48, Pyrite from bituminous coal mines; 59, Bog

Jan 1, 1933

By G. Campbell

The paper by M. Lonoff looks at the importance of byproduct prices on copper production. The paper develops several interesting points on this topic, but there are some points in the theoretical discussion that could use further development. A couple of these theoretical topics will be considered here using the paper's framework of assumptions without concern about how realistic the assumptions are for the copper industry. Lonoff’s theoretical model is based on a static, homogenous world where all copper/byproduct deposits are identical, and these deposits are the main source of these metals. Due to the importance of the byproducts to the production decision, the term coproducts will be substituted for the term byproducts to reflect more accurately this condition. The conclusion is drawn that a rise in coproduct prices necessitates a decrease in copper prices because copper production is increased as a consequence of increased coproduct production. The observation that real world behavior does not always follow this pattern is dismissed as "speculation." However, it can be easily shown that within this simple framework market forces might create the observed behavior. The key question to be answered is what causes coproduct prices to rise. Three possible cases will be used as illustrations. The first case is the one implicity assumed by Lonoff. Here, the demand for coproducts increases at all prices (an outward parallel shift of the demand curve) with the demand for copper remaining constant. As reported in the paper, the results are higher coproduct prices, an increase in coproduct production, and lower copper prices due to the resulting increase in copper production. The second case is when the supply of coproducts are constrained-leading to higher market prices. Copper production, as required by the simple model, is also reduced which

Jan 1, 1984

By Charles M. Rolker

It is not my purpose to present a complete description, still less a thorough discussion from a theoretical stand-point, of the Leadville ore-deposits. Hence I have given to this paper the more modest name of " Notes;" since it is little more than a record of observations made three or four years ago, and now published from my original memoranda, with the view of preserving the facts rather than of

Jan 1, 1886

By William C. Buell

As used in connection with open-hearth or other high-temperature operations, "insulation" refers to a multitude of substances, natural or manufactured, that have the one principal property of preventing the flow of heat by conduction to a greater degree than refractories can prevent it, the principal properties of the latter being resistance to temperature and/or chemical action. The term "control" as commonly applied to the mechanization of management functions is inappropriate without qualification, for without some degree of control of every operation we could produce no steel worthy of the name. Although grouped together in this paper, insulation and control in open-hearth furnaces have little, if any, interrelationship, therefore the paper is made up of two distinct parts. INSULATION OF OPEN-HEARTH FURNACES More than ten years ago the writer proposed the insulation of an acid open-hearth furnace system below the charging floor, and it was accomplished, with gratifying results. Possibly that was the first time the insulation of regenerators and slag pockets of any open-hearth furnace was undertaken, but shortly thereafter such insulation became general, and when the six groups of 15D-ton furnaces' were built in 1929-1930, they were completely insulated below the charging floor. While the practice was accepted at least five years ago, it was not well understood, however, as indicated by the following incident which occurred in connection with an installation made in 1929. After the

Jan 1, 1935

By John Blatchford, H. O. Hofman

The leading antimony mineral is stibnite. In smelting stibnite ore two processes are available, precipitation and roasting-reduction. The former is suited only for high-grade ores. As low-grade ores are more common than high-grade, roasting-reduction is of greater importance than precipitation. In the roasting process the aim may be to leave the oxidized antimony in the ore, or it may be to volatilize as much of the antimony as possible, collect the volatilized oxide as a rich intermediary product and smelt it for antimony, leaving the gangue poor enough to be considered a waste product. Whichever way the roast is conducted certain difficulties inherent in stibnite are encountered. These are: 1. The low melting point of stibnite which, according to Pélabon,' is 550°C., according to Wagemann2 540°C., and according to Borgstroma 546°C. 2. The ignition temperature: According to Friedrich,4 stibnite, if heated in air, begins to oxidize at 290°C. if the size of a grain is 0.1 mm. in diameter; at 343", if 0.1 to 0.2 mm.; and 430" if 0.2 mm. 3. The fusibility of a mixture of Sb2S33 and Sb203 which in the form of kermesite (Sb2S3)z.Sbz03 melts at 517°C.6 4. The volatility of Sb2Ss and SbzOs, for which no numerical data appear to exist, although practical experience has shown that they are volatile at low temperatures. As regards the oxidation of metallic antimony, we have the experimental evidence of C. F. Plattner6 that when fused and brought to a red heat, it burns with a bluish-white flame to Sb2Oa which passes off as a

Jan 1, 1916

By V. F. Hollister

The South American porphyry copper province includes most of the Andean orogen, excepting the tin province of Bolivia. Porphyry coppers have not been commonly found within the tin belt, though copper-tin deposits in San Rafael, Peru and copper-tungsten deposits in Llamuco, Chile, are known. James" shows the depth to the Moho to appreciably thicken where the tin belt exists, but disclaims any genetic significance from this coincidence. Table I gives some of the most important porphyry copper deposits explored to date, but does not include Antaminas, Peru, nor a number of other large skarn deposits associated with intrusions. V. D. Perry* points out that porphyry copper mineralization does occur to some extent in the intrusion associated with many of these skarn deposits. Also not included are the suspected possible porphyry type occurrences, such as, for example, quartz-sericitically altered lower levels of the Casapalca mine, Peru. Many deposits not well enough documented to list in a summary paper are also excluded. Should anyone care to tabulate all other large copper de- posits in South America, they could demonstrate that a tremendous potential awaits the proper political and economic climate in the future.

Jan 8, 1973

By Thomas M. Tharp

INTRODUCTION Attempts to analyze the stability of slopes, foundations and underground openings in discontinuously jointed rock have generally assumed full joint continuity or ignored the role of stress concentration at the tips of discontinuous joints. The most common approach in rock slopes is to consider a failure plane consisting of coplanar, but discontinuous joints separated by intact rock. The intact rock is assumed to fail in shear as a Mohr- Coulomb material and to contribute a strength component proportional to the fraction of the failure plane that is intact rock (Jennings, 1970). An alternative approach by Stimpson (1978) applies Lajtai's (1969) theory for shear strength of discontinuously jointed rock masses to slopes. Lajtai allows tensile failure in the intact rock of a composite surface. This theory yields lower shear strength than that of Jennings (1970) except in the presence of high normal compression, however it also fails to account for the stress concentration at the tip of a discontinuous joint. For a given slope geometry, stresses increase with slope height, but in both of these models rock mass strength is independent of size. A fracture mechanics analysis shows that particularly for small slopes, rock mass strength decreases with size. A continuous stepped failure surf ace produced by propagation of preexisting joints may develop at lower shear stress than predicted by the Jennings (1970) or Lajtai (1969) models. This fracture mechanics model applied to slopes in competent rock is more realistic in its assumed failure mechanism, and for large slopes more conservative than the Jennings (1970) or Lajtai models (1969).

Jan 1, 1984

By Robert Glass Cleland

BECAUSE of the country's vast mineral resources, Alexander Von Humboldt, the great German scientist who visited Mexico, or the Kingdom of New Spain, a hundred and fifty years ago, very aptly called that country the "Treasure Chest of the World." During the three centuries of Spanish rule, mining was the principal industry of the kingdom, the largest contributor to the country's prosperity, the chief common denominator in Mexican economic life. Public revenues and private fortunes, employment and markets, agriculture and trade, charities and churches, the incentive for frontier settlement and exploration, and the funds for outfitting the expedition of colonizer and conquistador-all were dependent upon the streams of precious metals that flowed century after century from the mines of Guanajuato, Zacatecas, Real del Monte, San Luis Potosi, and scores of other minería that lay scattered everywhere throughout the land. Sonora, one of the oldest and most renowned of the frontier provinces of New Spain, had been the scene of a hundred rich strikes, sudden stampedes, and widely heralded bonanzas long before the famous and frenzied Gold Rush

Jan 1, 1952

By J. B. Clemmer

PRODUCTION of magnesium metal in the United States during the past decade has increased from less than 600,000 lb. in 1928 to more than 4,800,000 lb. in 1938.1 The growing industry has stimulated interest in methods of production and in sources of raw material. All of the present domestic production is from brines. However, the availability of large tonnages of magnesite in the state of Washington, together with the possibility of cheap power, have created interest in the utilization of magnesite for the production of magnesium metal as well as for other purposes. Magnesite, the carbonate of magnesium (MgC03), usually is associated with lime-stone (CaCO3) and dolomite (MgC03 CaCO3). It occurs in crystalline and microcrystalline (sometimes termed amor-phous) forms.2 The more common crystal-line mineral is found in various shades of white, gray, yellow and brown, the colors being due to impurities, chiefly iron. Magnesite has a hardness of 3.5 to 4.5 and a specific gravity of 3.0 to 3.1. It forms rhombohedral crystals in the hexagonal system, having a vitreous, pearly luster. The quarries and mines of the Northwest Magnesite Co. near Chewelah, Wash., are large producers of magnesite for refractories.

Jan 1, 1940

By Edward J. Ryan, E. A. Peretti

iV preliminary X-ray and metallographic survey of the ternary system Bi-In-Te revealed that the following isopleths could form quasibinary systems: InTe-Bi, InTe-InBi, InTe-BizTe3, and InzTe3-Bi2Te3. The nature of the InTe-Bi phase diagram was established by Bologna and Peretti.' This article presents the results of an investigation of the InTe-InBi system by thermal analysis, X-ray methods, and metallographic examination. The bismuth and tellurium were bought from the American Smelting and Refining Co. The tellurium had the following spectrographic analysis: 0.0001 pct Mg, 0.0001 pct Si, 0.0001 pct Fe, 0.0002 pct Al, and 99.999+ pct Te (by difference). The bismuth assayed: 0.0001 pct Mg, 0.0001 pct Pb, 0.0001 pct Fe, 0.0001 pct Cu, and 99.999+ pct Bi (by difference). The indium was obtained from the Indium Corp. of America and contained 0.002 pct Cu, 0.006 pct Pb, 0.01 pct Sn, 0.01 pct Zn, and 99.97+pct In. The alloys were made by melting the required proPortions of InTe and in evacuated, sealed quartz

Jan 1, 1967

By R. F. Frantz, T. P. McNulty

The upper-level mineralization of the din Buttes, Arizona copper orebody consists primarily of dilute copper silicate impregnation in fault clay and throughout the altered limestone hostrock. Cuprite and native copper are minor with true chrysocolla rare. Owing to the high calcium carbonate and to the hydrogen ion exchange capacity of the clays, acid leaching would be economical only with cheap acid available. Leaching of the silicate copper with reagents other than sulfuric acid is slow and incomplete unless the ore is first heated to disorder the mineralized grains and to reduce partially the contained copper. Following heat treatment, 70 to 90 percent of the nonsulfide copper can be dissolved in aqueous anrmonium carbonate. Recovery of a pregnant solution by counter-current decantation is effective provided ammonium carbonate solution is added to the washing stages in order to oppose adsorption of dissolved copper by clays in the residue. Thermal stripping of the pregnant solution permits recovery of ammonia and carbon dioxide while precipitating copper either as oxide or carbonate. The research program was carried from batch tests through continuous miniplant operation to a five-month campaign in a 20 TPD continuous pilot plant. Pilot plant results, the relationships among key varibles, and a detailed flowsheet are given.

Jan 1, 1973

By Richard P. Rothwell

A REFERENCE to the geological map of Alabama shows the coal- measures of that State to form three distinct fields. The Coosu, or most easterly, contains about one hundred square miles ; the Cahaba, or middle field, which is also the most southern true coal in the United States, contains about 230 square miles ; and the Warrior field, which contains in the State of Alabama some 5000 square miles, is the southern extremity of the great carboniferous deposit, which extends through Pennsylvania, West Virginia, Kentucky, Tennessee, and Georgia. But very little has yet been done towards developing those coal- fields, partly owing to the absence of all commercial manufacturing enterprise in the South under slavery, and partly owing to the want of capital and the disturbed condition of the South since the war. During the past three or four years I have devoted a large part of my time to the examination of the coal and iron ores of this range,

Jan 1, 1874

By D. S. Cahn, D. W. Fuerstenau

Specimens of glass, plexiglass, and naturally occurring minerals were irradiated by a 15-joule ruby laser pulse to determine criteria for the fracture of nonmetallic solids by internal thermal stresses. Fracture did not occur in those specimens with either a very high or very low internal absorptance or with a high spectral reflectance. If significant amounts of melting and vaporization do not occur at the surface of irradiation, the specimen will fracture if a derived 11fracture stress" exceeds the ultimate tensile strength of the specimen. The purpose of this investigation was to determine criteria for the fracture of nonmetallic solids by internal thermal stresses which are caused by absorption of laser irradiation. A laser produces a very short pulse of light which has a high energy density distributed over a very narrow part of the visible spectrum. The laser system used in this investigation had an energy output of 15 0 joules at a wavelength of 6940 A. Fracture in a non-metallic solid, then, would be caused by the absorption of light energy by that solid, and subsequent conversion of this energy to heat or mechanical energy. Fracture is caused by internal stresses that result from rapidly imposed nonequilibrium thermal gradients. ANALYSIS OF CONDITIONS FOR FRACTURE BY LASER IRRADIATION For this analysis, the laser beam is assumed to be circular and centered on the junction of the major and minor axes of a rectangular specimen. The laser beam forms a cylinder of radius rb extending through the specimen width. The beam cylinder may be then thought of as a heated mass constrained by a surrounding unheated mass. The instantaneously heated cylinder will at-

Jan 1, 1968

By Charles J. Haas

The effectiveness of rock bolts in resisting shear displacement along preexisting fracture surfaces or slip planes was determined in the laboratory with full-scale bolts and large-scale shear test equipment. The system variables were the type of bolt, orientation of bolt relative to shear surface, and normal pressure on the interface. Results showed that, in general, both conventional bolts and resin- grouted reinforcing bars significantly increase the shear resistance along a fracture or bedding plane when the average normal compressive stress on the plane is in the order of 25 psi and when the bolt is oriented such that it tends to lengthen as the shear progresses. An increase in shear resistance is also noted at the higher normal pressure of 250 psi; however, the increase is small compared to the corresponding shear resistance without a bolt. Conventional bolts oriented such that they lose tension as shear displacement occurs added no shear resistance since the tension drops to zero at very small shear displacements.

Jan 1, 1977

By Jill Dill Pasteris

Several mineralogical prospecting techniques are used in diamond exploration. Most are concerned with identifying indicator minerals such as pyrope garnet and magnesian ilmenite, which are derived from mantle xenoliths hosted by kimberlites. The first goal of such prospecting is to locate kimberlite intrusions; the second goal is to identify the diamond-bearing kimberlites. Explorationists have worked much less on the indigenous kimberlite phases. The kimberlitic opaque oxides, ilmenite and particularly spinels, promise to be useful in discriminating between intrusion episodes in identified kimberlites, and perhaps in the evaluation and prediction of diamond grades. Several petrologists have showed that spinel compositions and zoning patterns are specific to certain intrusive facies in South African and Canadian kimberlites. Careful evaluation may indicate a correlation between spinel parameters and diamond content.

Jan 1, 1984

By M. A. Olade

Biotite, magnetite and quartz feldspar separates from rocks around porphyry copper deposits in the Highland Valley have been analyzed for copper, zinc and other related trace and major elements. Results show high copper concentrations in mineral samples close to mineralization, with a strong positive correlation with whole-rock copper contents. Zinc, on the other hand, shows no cleat-cut systematic relationship to mineralization, although there is a subtle decrease in the dues obtained for anomalous biotite samples. Manganese, cobalt and nickel in biotites show similar patterns as zinc. Using a sulfide-selective leach, it is show that the enhanced copper dues in mineral samples proximate to mineralization can be accounted for by the presence of minute inclusions of sulfides. In contrast zinc seems to occur in isomorphous substitution for femic elements, in a form that is leachable by hydrothermal activity. Results also show that copper content of biotite has a positive correlation with the modal proportion of biotites and their iron contents, whereas a negative relationship with manganese is apparent Geochemical contrast for copper between background and anomaly is not better in mineral fractions than whole rocks, consequently the use of minerals as sampling media shows no obvious advantage for mineral exploration purposes in the Highland Valley district.

Jan 9, 1979

By Edward C. Morse

The metallurgical history of Republic has been completely reviewed in a paper presented at a previous meeting of the Spokane Local Section by Professor Thomson;' therefore, the present paper will be confined to matters directly pertaining to the San Poil mill: When I came to Republic last fall to look over the situation there was a plant in operation successfully treating the tailings from one of the earlier mills in the camp. I refer to the mill of the Rathfon Reduction Co. This mill was operating in accordance with modern cyaniding practice, and I was given to understand that the work was very satisfactory and profitable, else it would not have been continued as long as it was. At that time I obtained much metallurgical information of value from Harry W. Newton, Superintendent of the mill of the North Washington Power & Reduction Co. I took a number of samples from the San Poil mine, with the view of determining if Mr. Newton's experience with the ores from the other mines applied to the San Poil ores. I made a large number of tests under a variety of conditions, and found that it was possible to extract as high as 98 per cent, of the values from San Poil ore by the laboratory-tests when the ore was pulverized to 200-mesh and treated with a solution of a strength of 5 Ib. of KCN to the ton. A fairly strong solution was required because of the proportion of silver in the ore, which makes it, from a metallurgical point of view, practically

Jan 1, 1913

By Douglass D. Donald

The New Jersey Zinc Co. successfully holed through a 2 ½ -mile haulage tunnel connecting its new Ivanhoe shaft with the Van Mater Shaft at Austinville, Va. This 8 x 10-ft cross-section tunnel was driven from both ends and met at a point approximately a mile from one shaft and a mile and a half from the other. In order to make certain that the faces met accurately on line and grade it was necessary to refine conventional mine surveying practices. The mines that are serviced by these shafts are located in the southwestern part of Virginia approximately midway between Roanoke and Bristol at the west foot of the Blue Ridge. While the presence of lead-zinc sulfide ores has been known in this area for more than 200 years, it was in 1902 that New Jersey Zinc Co. acquired the Austinville property, which has been in constant operation since that time. About ten years ago the company undertook an extensive diamond drilling program at Ivanhoe several miles to the southwest. This program was successful in locating sufficient ore to justify the purchase of a number of the properties in this area and plans were made to develop the new orebodies. The discovery of this ore as well as substantial additional reserves at Austinville resulted in a decision by the company to increase its daily milling capacity to 3000 tons, of which about 1000 tons would be supplied from the Ivanhoe mine.

Jan 9, 1958

By D. Jenkins

The Franklin Laboratory was designed mainly for the analysis of the products from the two concentrating mills situated at Franklin and Sterling Hill, the most important determinations being the zinc, iron, manganese, lime, moisture, and silica contents of the ores. Within the last 4 years, however, it has been found advisable to examine most of our supplies, and therefore additional space and equipment was allotted for the examination of such substances as oils, greases, soaps, alloys, fuels, paints, explosives, and water. The building as shown in elevation (Fig. 1) and plan (Fig. 2) consists of a main or routine laboratory, an experimental laboratory, a water analysis room, and the other accessories such as stock room, library, sampling and drying rooms, and office. The main laboratory is further divided into a balance room and zinc analysis room. As the greater part of our determinations are volumetric, good light is a very important factor and with this in view the interior malls of the building were constructed of white enameled brick laid in Keene cement. These also have the additional advantage that they give a clean and attractive appearance to the room. The windows are large, being 76 by 44 in. and even on very dark days the light is good throughout the whole laboratory. Our zinc titration requires a constant light and as, on many days, especially in winter, the light is variable, we installed two Artificial

Jan 1, 1918