Search Documents

By F. F. Hintze

Petroleum production in the Rocky Mountain district during 1929 registered a small decline from that of the previous year, conforming with a gradual decrease in the amount of oil produced during the last few years. A number of causes may be mentioned to account for this result, chiefly overproduction in other regions and the apparent desire of operators in this territory to conform to the policy of proration and retrenchment adopted by special agreement among operators in many of the fields. Unit operation has been adopted to control oil production from the Sundance sands in the Salt Creek field, Wyoming, in line with the general effort to stabilize this phase of the industry and prevent excessive drilling of new wells. Another factor which greatly retarded development in the Rocky Mountain region was the executive order of President Hoover issued in March refusing the award of new prospecting permits to future applicants and threatening cancellation of all existing permits upon which actual drilling had not been done as specified by law. Only four states in the Rocky Mountain region are important oil producers. In 1929 Wyoming led with an average daily output of 52,600 bbl., followed by Montana, with 10,730 bbl.; Colorado, with 6500 bbl., and New Mexico with 2700 bbl. daily average. These states bear the following percentage relation to total production in the Rocky Mountain district: Wyoming, 72; Montana, 15; Colorado, 9; New Mexico, 4., (Table 1.) The total average daily production was approximately 73,000 bbl. and the total production of all four states during the year was 26,534,606 bbl. This is 2.7 per cent. of the total oil production of the United States during this period. Colorado Although Colorado is not a large producer of oil and natural gas, its oil operations are widely distributed over the state. The Florence field is one of the oldest oil fields in the country, and there are good reasons for believing that the state will retain its place for many years to

Jan 1, 1930

By W. Rogers Wade, Alfred Wandtke

The Pilares mine of the Moctezuma Copper Co. is situated at Los Pilares de Nacozari, Sonora, Mexico, about 75 mi. (120.7 km.) south of the international boundary and about 7 mi. (11.26 km.) east of the town of Nacozari de Garcia. It is situated at an elevation of 5000 ft. (1524 m.) in one of the northward trending ridges that form part of the mountain mass that culminates in the Sierra Madre de Mexico. To the east, south, and west, the topography is rugged and diversified; to the north less diversity exists, ranges of mountains rise sharply out of almost level ground and give the basin range structure characteristic of the Southwest. The climate is dry, the average rainfall of 15 in. (38 cm.) being confined almost entirely to the months of June, July, and August. The winter consists of a few days of disagreeable weather when a little snow may fall; the remainder of the year is thoroughly delightful. Vegetation is typical of a semi-arid region. In the canons near the mine, where water flows intermittently, willows thrive; on the northern slopes of some of the mountains and in some of the broader canons pines may even become abundant. The dominant rocks are flows and pyroclastics which are cut by dykes, stocks, and batholiths. The mountain just west of Nacozari is, in part, composed of limestone of an unknown age which occurs as a syncline and is undoubtedly a part of a prevolcanic land surface. Overlying the limestone and faulted against it, are the volcanics; cutting the limestone is a coarse biotite granite. Whether the granite is older or younger than the volcanics has not been definitely established. No attempt has been made to differentiate the rock types of the volcanic~, of which there are exposed 3000 ft. (914 m.) in thickness of basic and acid flows (andesites, latites, and rhyolites) and andesite and latite tuffs and breccias. The latite breccias, the youngest of these volcanic~, cover the highest mountains in the immediate vicinity. The

Jan 1, 1920

By Alfred H. Bell

Illinois produced 5 per cent more crude oil in 1934 than in 1933, because there was less curtailment, and. the value of the year's production at the wells was 35 per cent more than that of the previous year. The average price of Illinois crude oil in 1934 was $1.13 as compared with $0.87 in 1933, an increase of 30 per cent. The quotas of allowable production for Illinois during 1934, as authorized by Oil Administrator Harold L. Ickes, were as follows: January, February, March, 12,000 bbl. per day; April, May, 12,500; June, July, 12,600; August, 12,500; September, October, November, 12,000; December, 11,700. No other restrictions on production were in effect during the year until Oct. 11, when it was found necessary to prorate the fields to 75 per cent, a curtailment of 25 per cent below the quota fixed by the Federal Administrator. On Dec. 1 the curtailment was reduced to 18 per cent and on Dec. 18, to 15 per cent. Production in Illinois by months during 1934 was as follows: Barrels Barrels January...................... 393,000 July........................ 394,000 February.................... 337,000 August..................... 402,000 March....................... 394,000 September.................. 378,000 April......................... 373,000 October.................... 352,000 May......................... 411,000 November.................. 305,000 June......................... 392,000 December................... 321,000 Total ................... 4,452,000 In spite of higher prices for crude oil, fewer wells were drilled in Illinois in 1934 than in 1933 (Tables 1 and 2). Of the 26 wells drilled, 10 were oil producers, 8 were in proved fields and 2 were in a new pool in Wabash County, l½ miles south of the nearest production, one was a small gas well on the Stubblefield anticline in Bond County, one was an input well for repressuring in the Colmar-Plymouth field, McDonough County, and 14 were dry holes, mostly scattered wildcat tests.

Jan 1, 1935

By J. H. McCormick

THIS plant, near Marysville, Mont., was planned to treat the ore from the Piegan and Gloster mines, the latter being one of the early and famous producers of the Marysville district. When the mill was closed in 1888, treatment consisted of stamp milling, followed by pans and settlers for pan amalgamation. The extraction was evidently poor; because, a few years later, thousands of tons of tailings were re-treated by the ranchers in the valley below the mill, by the then new cyanide process, and gave a handsome profit. In 1914, the present owners, after laboratory tests and an experimental mill run, decided upon the following treatment: crushing to 40 mesh in cyanide solution, concentration, amalgamation, classification, and cyanidation of sands by leaching, and of slime by agitation and decantation in charges. The ore averaged about $7 per ton, gold and silver, the ratio of weight being 1 oz. gold to 7.56 oz. silver. The ratio of gold and silver in tailings was 1 oz. Au to 36.6 oz. Ag; the quartz vas sharp and, sandy, however finely ground, and rather difficult to slime. The mechanical 'equipment was a No. 5 Symons gyratory crusher; three 10-ft. Lane slow-speed Chilean mills; one Wilfley roughing and one finishing table; one submerged-type Akins classifier; five 26 by 10-ft. fir leaching tanks; one 24 by 7-ft. Dorr thickener; four 14 by 16-ft. Dorr agitators; four 6-compartment double-row zinc-boxes having compartments 18 in. wide, 18 in. deep, and 34 in. long; Johnson zinc lathe; acid and vacuum filter tanks for treating precipitate; roasting furnace; and Case tilting No. 275 crucible furnace for melting precipitate. The mill is driven by electric power supplied by the Montana Power Co. at the following rates, per kw.-hr.: 200 to 300 hp.,.0.68 c.; 300 to 500 lip., 0.61 c.; 500 to 750 hp., 0.55 c.; plus $1 per month per installed motor horsepower.

Jan 8, 1918

By Howard N. Eavenbon

The low-volatile, or smokeless, coal field of southern West Virginia is in Fayette, Raleigh, Wyoming, Mercer, Summers and McDowell counties, in the extreme southern portion of the state, and extends into the adjacent counties of Tazewell and Buchanan in Virginia. McDowell County is the largest producer, with Fayette and Raleigh counties next. The total area of the field (Fig. 1) is approximately 1600 square miles, or 1,024,000 acres. The percentage of volatile matter in the various seams ranges from 15 to 26 per cent, The upper limit of true low-volatile coal is usually considered to be 23 per cent volatile matter; above this point, the coal usually is classed as medium volatile. This limit will be used in this paper. Geological Position of Seams The smokeless seams are among the oldest coal seams in the country, as the Pocahontas group of rocks is the lowest member of the coal-bearing series and rests on top of the Mauch Chunk red shale, in or below which no coal seams of any importance occur. The Pocahontas group, or Lower Pottsville measures, has a thickness of 750 ft. in southern McDowell County, which decreases to about 350 ft. at Prince, on the New River, in Fayette County, 50 miles to the northeast. In this group, at various points, 12 coal beds have been found, of which 4 have been found in workable thickness and are now being mined. The New River group, or Middle Pottsville measures, is just above the Pocahontas group and varies in thickness from 1300 ft. in southern McDowell County to about 700 ft. along New River. At various places, 16 beds of smokeless coal have been identified in this group, of which 5 have been found in workable thickness and are now being mined. A general columnar section of these strata is shown on Fig. 2. The workable seams in these strata, arranged in geological sequence, are as shown on page 77.

Jan 1, 1932

By Victor De Ysassi

THE iron mines of Spain are located on the mountain ridge forming the boundary between the, Teruel and Guadalajara provinces, called Sierra Menera. They form a property of 25 mines extending over an area of 1,677 hectares (4,140 acres) situated at a height varying from 1,200 m. (3,940 ft.) to 1,500 m. (4,920 ft.) above sea level. The deposit follows the direction north to south; huge masses of ore are being found both on the slopes and at the summit of the Sierra. The ore occurs among quartzites and magnesite limestone, in some places overlaid by quartzite 15 in. (50 ft.) thick; in some others (and this is more general) the ore is overlaid by earth and boulders of quartzite origin,; this layer is about 8 m. (26 ft.) thick. The ore beds occupy the geological horizon of the Superior Trias or Muschelkask, which are here in direct contact with the Silurian quartzites. The lime-stones have been more or less transformed. There is ample evidence to show that these mines were worked in very ancient times-objects and tools employed in mining by the ancient Romans and Arabs are to be found plentifully in old workings which extend down into the deposits. It has been estimated that more than 10,000,000 tons of ore were mined in the old days in this district and carried to the primitive forges in the vicinity where iron of much renown in Spain was extracted. Remains of more than 20 of these forges are found in the neighborhood of Sierra Menera and are usually situated near waterfalls and forests. Much investigation has been carried on for the purpose of determining the quantity of ore to be found in these mines, but no exact calculations can be made at present. When the investigation is completed it will surely be found that the deposit contains a much larger quantity than the 100,000,000 tons indicated by the present workings.

Jan 2, 1916

By W. Mostowitsh

I. Introductory LEAD sulphate occurs as anglesite, and is formed in every roasting of lead sulphides or sulpho-salts containing lead. In smelting in the blast furnace an ore containing natural or artificial lead sulphate, a large part of the sulphur present goes to the formation of the intermediary product matte which requires further treatment for the recovery of the values it contains. It is therefore of importance to study the behavior of lead sulphate at elevated temperatures, both without and with reducing agents, especially as the information available gives data which are more or less conflicting. II. Decomposition of Lead Sulphate by Heat The dissociation of PbSO4 into PbO and S03 or S02 and 0 has been discussed by many metallurgists. The following data are considered to be representative. Doeltz and Graumann1 found that PbSO4 was not affected by heat at 800° C.; that dissociation began at 900° C., and was rapid at 1,000° when the salt lost in 1 ½ hr. 14.3 per cent. of its weight, the dry salt containing 26.43 per cent. SO3. Hofman and Wanjukow2 summarize their work upon the dissociation of metallic sulphates with the statement that the decomposition of PbSO4 begins at 195° C., but progresses very slowly, with the formation of the basic salt 6PbO.5S03 at 705°; that this salt undergoes a transformation at 847°, begins to be decomposed at 888°, to sinter at 896°, and to fuse at 910°; rapid dissociation begins at 952°, and is accompanied by volatilization of PbO; retardations at 958° and 962° indicate an acceleration of decomposition which, however, is not complete. Proske3 found that PbSO4 gave off at 900° C. in 30 min. only 0.63 per cent. of its SO3, and that the loss increased with

Jan 5, 1916

By Raymond M. Howe

Additional data have been secured on the disintegration of furnace linings and the spalling of stove brick. The first article on the disintegration of furnace linings appears to have been written by John Pattinson in 1876.l The furnace involved was 85 ft. (25.0 m.) higher and 27 ft. (8.2 m.) in diameter at the boshes; after being in blast five years, the top brick became contaminated with carbon and disintegrated. An examination of the lining showed that the discolored, disintegrated brick were in a zone found from 35 to 67 ft. (10.6 to 20.4 m.) above the hearth; immediately below, in a zone extending from 22 to 40 ft. (6.7 to 12.1 m.) above the hearth, the brick were hard and porcelain-like in appearance. Analyses of samples taken from the different sections are given in Table I. The water-soluble portion found in the sample taken 39 ft. (11.8 m.) above the hearth had a composition approximately as follows: silica, 0.50 per cent.; lime, 0.04 per cent.; potash, 0.78 per cent.; soda, 0.20 per cent.; potassium chloride, 6.19 per cent.; moisture, 1.03 per cent.; total, 8.74 per cent. The carbon Table 1.—-Analyses of Samples Taken from Diferent Sections of Furnace . I ii In Iv v Section 67 Section 45 Seotion 39 Section of Original ft Above ft above ft above vitrified Lining Hearth Hearth Hearth Portion Per Cent. per Cent per Cent per cent. per Cent Silica........................... 55.70 55.60 55.67 47.60 37.07, Alumina........................ 35.50 35.40 30.00 26.47 23.18 Ferric oxide..................... 3.00 1.32 0.96 Lime........................... 0.23 0.06 0.17 Magnesia....................... 1.22 0.95 0.86 0.00 Potash......................... 2.60 2.10 5.30 7.54 21.59 Soda.........,.................. 0.45 0.42 1.67 0-76 6.28 Ca1bon ......................... 2.05 3.24 5.97 Carbon dioxide.................................. 2.. 17 Water...................................... 7.70 Water-soluble........................... 8.74

Jan 1, 1920

By W. Mostowitsch

Lead sulphate occurs as anglesite, and is formed in every roasting of lead sulphides or sulpho-salts containing lead. In smelting in the blast furnace an ore containing natural or artificial lead sulphate, a large part of the sulphur present goes to the formation of the intermediary product matte which requires further treatment for the recovery of the values it contains. It is therefore of importance to study the behavior of lead sulphate at elevated temperatures, both without and with reducing agents, especially as the information available gives data which are more or less conflicting. 11. Decomposition of PbS04 by Heat The dissociation of PbSO4 into PbO and SO3 or SO2 and 0 has been discussed by many metallurgists. The following data are considered to be representative. Doeltz and Graumannl found that PbS04 was not affected-by heat at 800" C.; that dissociation began at 900" C., and was rapid at 1,000° when the salt lost in 1 1/2 hr. 14.3 per cent. of its weight, the dry salt containing 26.43 per cent. SO3. Hofman and Wanjukow2 summarize their work upon the dissociation of metallic sulphates with the statement that the decomposition of PbS04 begins at 195' C., but progresses very slowly, with the formation of the basic salt 6PbO.5SO3 at 705"; that this salt undergoes a transformation at 847") begins to be decomposed at 888") to sinter at 896", and to fuse at 910"; rapid dissociation begins at 952") and is accompanied by volatilization of PbO; retardations at 958" and 962" indicate an acceleration of decomposition which, however, is not complete. Proske3 found that PbSO4 gave off at 900" C. in 30 min. only 0.63 per cent. of its 803, and that the loss increased with

Jan 1, 1917

By Chung Yu Wang

DURING the time I was in charge, of this mine, from 1914 to 1915, I had occasion to read the interesting papers by T. T. Read and C. M. Weld about these deposits, to find how far their observations corroborated mine. To quote from the paper on "The Mineral Production and Resources of China" by T. T. Read:' "The iron ores at Tayeh lie along the contact between a marble and an intrusive body of a dark gray syenitic rock. * * * * At one place it is slightly magnetic, apparently having been partly reduced to the magnetic oxide by the action of reducing solutions, which have deposited small amounts of copper and iron sulphides along the foot wall." To quote from the paper on "The Tayeh Iron Ore Deposits"2 by C. M. Weld: "I find the orebodies described as occurring along an approximately E-W contact between horn-blende-granite and limestone. * * * * The granite is a granitoid rock consisting essentially of quartz, potash-feldspar and hornblende." These quotations show the differences of opinion entertained by two observers. My own study of these interesting deposits has been intermittent amid the manifold duties devolving upon a superintendent. General Description of the Deposits The deposits are situated to the west of the Yangtse River, being con¬nected with the river by a standard-gage railroad of 56 li (16.16 miles, 26 km.) in length, as shown in Fig. 1. The general topography of the region is of mature age, showing broad valleys with sluggishly meandering streams. These deposits are worked as two mines, named the Tieh Shan Mining Department and the Teh Tao Wan Mining Department; the former consisting of three orebodies more or less connected, named Tieh Man Kan, Sha Mau Tze and Lung Tung, and the latter consisting of Chang Pei Shan, Sze Tze Shan, Ta Shih Men, Yeh Chih Ping and Tsin Shan, also more or less connected, as shown in Fig. 2.

Jan 3, 1917

By D. Argyriades, G. Derge, G. M. Pound

The electrical conductance of molten FeS was studied as a function of temperature and composition. It was found that stoi-chiometric FeS (36.5 pct S) shows a minimum specific conductance of 400 ohm-1 cm-1. For the Fe-rich melts the conductivity increases with increasing amount of iron to about 4850 ohm-1' cm-I at 26 pct sulfur. For the sulfur-rich melts the conductivity increases with increasing amount of sulfur until it reaches a maximum of 1300 ohm1 cm-1 for 37.4 pct S and decreases to 800 ohm-1 cm-1 for 38.3 pct sulfur. It is concluded that molten stoichiometric FeS is an intrinsic semiconductor in which the forbidden gap in the electron energy level diagram is quite narrow. Excess sulfur acts as an acceptor impurity in providing a component of positive hole conduction, while excess iron acts as a donor impurity to increase the n-type conduction. K. Bornemann and G. von Ftauschenplatl used a four-terminal, direct-current cell to study the electrical conductance of molten copper sulfide. Their measurements showed a high conductivity, of the order of 100 ohm-1 cm-" and a positive temperature coefficient. From electrolysis studies, Savelsberg2 concluded that molten Cu2S and molten FeS are electronic conductors. Further. he found that molten FeS has a high specific conductance, of the order of 1500 ohm-' cm-', and a small negative temperature coefficient. Pound, Derge, and Osuch,3 using an ac Kelvin circuit and a four-terminal cell, measured the specific conductance of molten Cu,S, molten FeS, and various mixtures. They found that the specific conductance of the solutions followed a roughly additive rule of mixtures. Yang, Pound, and Derge4 showed from electrolysis measurements that the mechanism of electrical conduction in molten Cu2S, FeS, and mattes is primarily electronic. Further, they observed that small additions of CuCl suppress the electronic conduction whereupon the system behaves ionically.

Jan 1, 1960

By A. Faber du Faur

At the request of some of the members to whom I have shown a collection of specimens of sulphur from southern Utah, I herewith present some notes relating to the mines and the method of extracting the sulphur from the ore. In preparing these notes I have borrowed from a paper by Prof. G. vom Rath, published in the Neue Jahrbuch fur Mineralogie, vol. i., 1884, dated Salt Lake City, December, 1883. The Cove Creek sulphur-bed, now worked by the Dickert & Myers Sulphur Co., is in Beaver county, near the line of Millard county. It was first discovered by Mr. Ferdinand Dickert in 1869 ; other beds in the same neighborhood mere found by him from 1872 to 1875, making altogether 22 mining claims. The want of railroad communication prevented the early development of these claims; but in 1883 Mr. F. Dickert put up a plant for extracting sulphur from the ore, which proved a perfect success; and in 1885 the property was transferred to a stock company organized under the laws of Utah. The railroad station nearest to the Cove Creek mines is Black Rock, on the Utah Central Railroad, 204 miles south from Salt Lake City, and about 26 miles west of the mines. The road from Black Rock to the mines passes through desert and lava-bed, to the road leading from Kanosh to Beaver, which latter road it joins near Cove Creek fort, a square stone enclosure, erected by the Mormons for protection against the Indians. Cove Creek fort is situated near the eastern limit of a plain bounded on the west at a distance of about 12 miles by the Mineral range, and on the east by the Sulphur mountains, forming part of the Tushar mountains. To the northwest the plain runs into the Sandy desert. About 3 miles from the fort rises a solitary hill about 1000 feet above the

Jan 1, 1888

By Truman Aldrich

THE Clinton group of the Silurian holds the red or fossiliferous ore; its outcrops have been mapped by the State or U. S. Geological Survey. This group is from 100 to 500 ft. thick in Alabama. There are places where it is entirely missing (doubtless islands in the Silurian Sea). In Etowah County, in part of Greasy Cove and vicinity, the upper seam is a coral reef impregnated with the red ore; in this same county, step, faults bring up the ore in three or four separate ridges practically parallel. In Blount County and on Raccoon Mountain, the ore runs under the carboniferous rocks and outcrops in the valleys. In examining some bore holes made in drilling for oil, the writer found the Clinton group continuing under the Warrior coal field wherever the drill has gone deep enough. It demonstrates the possibility of a source for red ore not seriously thought of until lately. The following bore holes made principally for oil, given in Bulletin No. 22, Geological Survey of Alabama, show the presence of either ore or red rock, and suggest vast resources yet to be outlined and developed for ore in the future. The locations are given by number on the map. Hole No. 1 was drilled 6 miles southeast of Russellville, Franklin County, by the Woodward Oil & Gas Co. It passed through 160 ft. of Clinton, but only a small show of red ore was found at 1280-1400 feet. A test well, No. 2, drilled near Atwood, Franklin County, in section 26, township 8, range 14, penetrated the Clinton at 1608 ft. and found 38 ft. of limy red rock, also 8 ft. of some blood red ending at 1820 ft., making 46 ft. of red rock in all. It is reported that some good ore was cut through but this work was done by a churn drill. The hole was continued by diamond drill from here. At least 400 ft. of the formation was classified as Clinton.

Jan 10, 1924

By T. A. Rickard

Clement Le Neve Foster was born at Camberwell on March 23, 1841, his father being Peter Le Neve Foster, who was secretary of the Society of Arts for 26 years. As a boy of 12 he was sent to school at Boulogne, receiving a preliminary education there; and in 1857, when only 16 years old, he took his degree of Bachelor of Science from the University of France. In October of the same year he returned to London and entered the Royal School of Mines, which was then in Jermyn Street. He distinguished himself by winning a scholarship and a medal, and by securing his degree as Associate of the Royal School of Mines in the abbreviated period of two years. This was followed by a year at the Bergakademie at Freiberg; subseque1:tly he visited several mining districts in Germany and Hungary. On returning to England, in November, 1860, he received from Sir Roderick Murchison an appointment upon the Geological Survey. During five years he was engaged in field-work, first on the Wealden beds in Kent and Sussex, and then in Derbyshire and Yorkshire. At this time his evenings were largely devoted to reading for a degree from London University. In 1861 he matriculated, obtaining the Bachelor of Science in 1863, with honors in biology and a University scholarship in geology; in 1864 he passed the two examinations entitling him to the Bachelor of Arts degree, and in 1865 he received the degree of Doctor of Science. In 1865 he succeeded Mr. Richard Pearce as lecturer to the Miners' Association of Cornwall and Devon. At the same time he became the curator to the museum of the Royal Geological Society of Cornwall at Penzance, a member of the council in 1873, and a life-member in 1874; he made frequent donations to the museum, besides contributing several valuable papers to

Jan 1, 1905

By John Treweek

FOR many years the Homestake Mining Co. has devoted serious attention to the elimination of accidents, and ground is steadily being gained in this direction. In accident prevention work it is line-plunging with perfect teamwork and not the spectacular forward pass that brings progress toward the goal. In both surface plants and under- ground workings we regard "good housekeeping" as a first requisite for safety as well as efficiency. Under this term are included all types of safety guards and protective devices as well as cleanliness and orderliness it working places. Perhaps the most important factor in safety work is to arouse and maintain employee interest. The general morale and contentment of employees is of particular importance.

Jan 1, 1938

By P. Bandopadhyay, T. C. Rao

Geologically the Indian coals belong to Gondwana formations. Being of drift origin, these coals contain high percentage of mineral matter distributed in finely disseminated form. Indian coal-preparation plants process prime coking and medium coking coals for use in steel plants. Limited resources of good quality coking coals (Table 1) could not keep pace with the rapid developments of the iron and steel industry in India. This resulted in the introduction of coal-preparation technology and the establishment of washeries in India in the last 30 years or so. The first four washeries were set up during the early fifties at West-Bokaro, Jamadoba, Lodna and Kargali. Next came the first non-coking coal washery at Nowrozabad set up by the Associated Cement Company. In 1961, following the recommendation of Central Coal Washeries Committee (1953-54), Hindustan Steel Ltd. had set up five central washeries at appropriate locations, viz Durgapur, Dugda (2 washeries), Patherdih and Bhojudih, so that the raw coal feed having similar washability characteristics can conveniently come from a number of collieries to a particular washery. Subsequently, to meet the increasing demand of metallurgical coal by steel plants, two more central washeries (at Durgapur and Chasnala) and three pit-head washeries (at Kathara, Swang and Gidi) were installed by 1970. The prime objective of washing Indian coking coal is essentially to reduce the ash content. All the washeries in India, taken together have an installed capacity of about 26 million tons of raw coal input per annum. Details of these washeries in respect of their annual capacity, main washing systems adopted and the nature and size of the products are given in Table 2. It can be observed from this table that (1) bulk of the coal is processed in units like jigs HM baths and HM cyclones; (2) only two of the washeries have cleaning circuits for treatment of fines.

Jan 1, 1980

By R. J. Mechin

Top-slicing was introduced in the Pachuca district in 1917 by T. C. Baker, at that time mine superintendent of the Santa Gertmdis mine. There then existed 1200 ft. below the surface, lying between the fourteenth and eighteenth levels (a vertical distance of 354.2 ft.) a block of ore having a length of 295 ft. and an average width of 82 ft. and dipping at an angle of 65°. This block lay in the hanging wall of the vein and consisted of highly altered and fractured andesite, cut through with mineralized quartz stringers. On the foot-wall side, 26 ft. of old filling, left by former operators, was of payable grade. Stoping therein was first undertaken by the square-set filling system, but because of the extremely heavy hanging wall and loose dry filling in the foot wall, all square setting had to be accompanied by spiling, which made the operation exceedingly slow and costly. A system of mining was sought that would eliminate the difficulties inherent to the square-set system in heavy ground and that at the same time would effect the desired economies in mining. After several years, top-slicing has met all the conditions most satisfactorily, so that when similar conditions presented themselves in El Bordo mine, this method was adopted with necessary modifications. El Bordo mine is operated by the Santa Gertrudis company, and is situated about two miles north of Pachuca. Because of the diversity of the orebodies, a number of different mining methods are in use, among them top-slicing. Description of Block of Ore Former operators, when mining the original vein, left in the foot wall ore of too low grade to be profitable at the time; also, considerabe low-grade material was sorted out and stored as filling in the stopes. Some pillars were left in place, either for support or because they were not payable. All this has formed a body of ore that can now be exploited

Jan 1, 1925

US 4,133,866-Selective recovery of the bound sodium content of red mud obtained in the production of alumina by the Bayer process The red mud is mixed with aqueous ferric sulfate, the resulting suspension stirred intensively at a temperature of 15-85°C and adjusted to a pH value of from 4.4 to 4 6, and the solids are removed. The clarified solution of sodium sulfate can be used directly for the leaching of additional bauxite T Lakatos, M Miskei, J Szolnoki, F. Toth, and L Revesz, assigned to Aluminiumipan Tervezo es Kutato Intezet, Almasfuzitoi Timfoldgyar, and MTA Geokemiai Kutatolaboratorium. Jan. 9, 1979. 3 pp (423-208). Filed: 10¬28-77 (846,588) Priority: Hungary, 10-29-76 (AU 364). US 4,145,398-Continuous digestion of bauxite with aqueous sodium hydroxide, with higher throughput in existing plants or the construction of smaller plants with equivalent capacity The ore suspension at a solids concentration of 1-6% by weight and temperature of 200-300°C is flowed through a digestion tube or nest of tubes at a velocity of preferably from 2 to 5 m/s and under a pressure of from 10 to 200 atm Heat is supplied by a fluid heat carrier flowing in countercurrent in a concentric outer tube. Preferably, some of the red mud is recycled to the digestion operation. L. Plass, assigned to Vereinigte Aluminium-Werke A.G Mar 20, 1979. 5 pp. (423-121) Filed: 2-27-76 (754,749) Same: British 1,437,548, dated May 26, 1976 Same Canadian 1,008,253, dated Apr 12, 1977. US 4,146,573-An aqueous slurry of red mud, formed in the Bayer process production of alumina from bauxite, can be solidified by treating the red mud with a described quaternary ammonium salt, continuing mixing until the red mud has set up to a rigid mass, and recovering the solidified concentrated red mud J Kane, assigned to Nalco Chemical Co Mar 27, 1979 4 pp (423-82). Filed 8-2-78 (930,251).

Jan 1, 1980

By W. M. Small

From the one producing well in Austria, 7000 bbl. of heavy oil was produced and sold in 1933. This well, owned by the Raky-Danubia, was completed late in 1932 in the formation called Flysch (Upper Cretaceous or lower Eocene) near Zistersdorf north of Vienna. Two wildcats drilling in the vicinity have not yet reached the producing beds. Near Vienna, the European Gas and Electric Co. drilled five shallow wells for gas, three of which were failures. One gas well was completed for 8 million cu. ft. capacity at 260 meters depth and with a pressure of 570 lb. Another is being tested following blowouts. One gas well and one dry hole were completed in the pool in 1932. In Upper Austria, the same company abandoned one wildcat at 679 m. and is drilling at 280 m. on a second. No gas was sold during the year, but a line is being completed to supply fuel to boilers of the Vienna Electric Works. Hungary No deep drilling was done in 1933. Oil and gas concession was granted by Parliament to the European Gas and Electric Co. on Trans-danubia. Active geological and geophysical investigation is in progress. Czechoslovakia In the Gbely and Hodonin shallow fields, some 26 wells were drilled of which three were reported as failures. The total production of the fields was 111,736 bbl. of oil and 40 million cu. ft. of gas used as fuel in the field. At Vacenovice, where there were already two small gas wells, a third producer was completed at 420 m. This pool markets a small amount of gas, which is compressed and used to light railway carriages. Wildcat wells were reported drilling at about 300 m. depth at both Jasina and Telnice. One 700-ni. wildcat near the Hodonin field was abandoned. Another failure was reported completed and abandoned at 820 m. near Holic.

Jan 1, 1934

By Eckley B. Coxe

I wish to call the attention of the Institute to a peculiar variety of anthracite which occurs in the Buck Mountain vein at our collieries at Drifton, and in the same and other veins in different localities in the anthracite coal-fields. It is known among the workmen as iron-gray or cast-iron. It has a dull, greasy appearance, as if a piece of ordinary anthracite had been rubbed with a dirty and greasy rag and allowed to dry. It was formerly considered a very impure coal containing a high percentage of ash, and was picked out of the coal and thrown away. But the following analysis of it and of its ash, made by Mr. J. Blodget Britton, of Philadelphia, shows that such is not the case, the percentage of ash not being much higher than that of the ordinary anthracites as they are prepared for market. ANALYSIS OF COAL. Water,.........4.36 Fixed carbon, by difference,.. 84.90 Volatile combustible matter,. . 3 48 Ash,..........7.26 100.00 The carbon proved to some extent to be of the nature of graphite, and slowly combustible. ANALYSIS OF ASH. Silica,.........25.66 Sulphur,........ .17 Alumina,........27.03 Phosphoric acid,.......21 Ferric oxide,.......42.83 Alkali, undetermined matter and Lime,.........1.56 loss,.........60 Magnesia,........1.83 Manganous oxide,......11 100.00 We recently collected a quantity of the substance and made a fire with it, in an ordinary stove, which was kept up several days. We found that it burned with intense heat, and apparently as freely as our other coal does. Mr. Britton is probably right in his view, that the difference in appearance is not due to impurities in the coal, but to the fact that the carbon is in a more or less graphitic form, as many of the standard coals are no purer. I bring this before the Institute as I know that a large quantity of this valuable fuel is thrown away every year, on account of its supposed impurities.

Jan 1, 1879