Search Documents

By Grover J. Holt

A DETAILED description of the many variations in iron mining and transportation practice in Minnesota would require much space. Since a fairly detailed description of the practices then in use was published in the guidebook issued in connection with the meeting of the Institute on the iron ranges in 1920, and subsequent developments have been described by E. E Hunner,1 M. H Barber,2 and A. E. Anderson, J. M. Riddell and G. J. Holt,3 it will not be necessary here to do more than review the highlights of current practice Details on any points of interest can be obtained through correspondence with the operators involved.† The iron ores of Minnesota, which have been formed through enrichment, of the iron formation in which they occur, largely by the removal of silica, are usually covered by a blanket of glacial drift known locally as "surface." Surface material, including sand, clay, hardpan and boulders, makes up the greater portion of the stripping in open-pit operations. In some instances, stripping also includes taconite and "paint rock," directly below the surface material and overlying the ore. Taconite is the iron formation, a ferruginous chert with interbedded slate layers. "Paint rock" is a local term for oxidized slate layers interbedded in the iron formation, high iii phosphorus, alumina and moisture The iron ores fall into two classes- (I) direct shipping (merchantable ores or ores requiring no treatment except possibly crushing or screening to make an acceptable sized product), and (2) ores requiring beneficiation (such as sintering, drying, washing, jigging, high-density treatment, or magnetic separation in the case of magnetite) The Mesabi Range produces chiefly soft Bessemer and non-Bessemer ores. The Cuyuna Range produces mainly low-manganese brown ore and high+manganese black ores, with some iron ore. The Vermilion Range yields mainly Bessemer and non-Bessemer iron ore, with some hard or lump ore that finds use in the open hearth. Open-pit mining is limited to the Mesabi and Cuyuna Ranges but underground mining is done on all three. The choice of mining methods is determined by the relative economics of overburden-removal and shaft-mining costs. STRIPPING PRACTICE Common practice has been to remove the bulk of the overburden during the winter season and to mine during the summer. In the present emergency many operators are forced to forego the economies attained by year-round utilization of equipment and to equip for, and carry on, stripping and mining simultaneously. In the normal years or lean years to come, most properties probably will be overequipped and high depreciation charges will have to be absorbed

Jan 1, 1942

By N. A. Zeigler

The present publication is a continuation of the work on gas analysis described in a paper presented before the Institute of Metals Division year ago.' While that paper was largely descriptive in character dealing with the various parts of the apparatus and method of operations the present one gives numerical data obtained as a result of a series c experiments with iron-carbon alloys. The apparatus and the method applied are essentially the same as previously described, changes bein only in minor details. Attention should be called to the fact that in the present work we ar dealing with the gaseous mixtures obtained as a result of vacuum meltin of various ferrous alloys. It should be understood that when the term "degasified sample" and "products of degasification" are used, the refer to the sample remaining after the vacuum fusion of the alloy an the gaseous products removed therefrom, respectively. The write does not wish to create the impression that the metallic products of thj process are absolutely free from any gaseous elements, nor that the gase obtained are present as such in the original sample. These two point are not yet definitely known and are subjects for future investigatior The point, however, which has been established beyond doubt, i that all the gases dealt with come from the metallic charge and ar present either in the charge as such, or are produced as a result of chemic: reactions going on within the charge. The suggestion that the gases an due to the reactions between the metallic charge and the refractor materials has no valid basis. General Procedure A series of iron-carbon alloys was prepared in a magnesia-line graphite crucible placed in a high frequency laboratory furnace open t the atmosphere. The materials used were Westinghouse electrolyti iron and Acheson graphite. Each alloy, after it was completely molter was kept in the liquid state for 10 min., cast into a small iron mold, an

Jan 1, 1929

By John L. Lamont, Walter Crafts

THE principle formulated by Grossmann1 for calculating hardenability of steel by multiplying the ideal diameter of "pure" iron-carbon alloys by factors for grain size and alloying elements has been confirmed on many steels and has proved useful in designing substitute alloy steels. Grossmann found that the typical behavior of the multiplying factors was to increase directly in proportion to the amount of the alloy present in a steel. However, the multiplying factor for the effect of silicon on hardenability was found by Grossmann to increase to a lesser degree as the amount of silicon was increased. In view of the in¬creasing use of silicon in heat-treating steels, the effect of silicon on hardenability is becoming more important. Calculation of the hardenability of high-silicon steels made at the Union Carbide and Carbon Research Laboratories, Inc., indicated that the multiplying factor for silicon increased directly in proportion to the amount of silicon present. A more extended study of high-silicon steels covering fairly wide ranges of grain size, carbon, manganese, and aluminum has confirmed that up to 2 per cent silicon the multiplying factor is directly proportional to the silicon content. Manganese and aluminum factors have also been determined. The results of the study offer strong confirmation of the general validity of Grossmann's multiplying principle. TESTING PROCEDURE Steels on which the study of the effect of silicon on hardenability was based were made in high-frequency induction furnaces using Armco iron and standard alloying materials. The ingots were forged to bars, and sections were normalized prior to machining Jominy hardenability test specimens. The Jominy test was carried out under standard conditions.2 The depth of hardness penetration for determination of ideal diameter at "half hardness" was taken at the hardness level indicated in Fig. 20 in Grossmann's paper by the solid line for 50 per cent martensite in plain carbon steel. The depth of penetration of hardness on the Jominy specimen was converted to ideal diameter by the relation given in Fig. 28 of Grossmann's paper. Chemical analysis was determined on a sample taken adjacent to the Jominy specimen. Aluminum was determined as "acid-soluble aluminum" rather than as total aluminum, as it is probably more representative of the aluminum that is effective as an alloying agent. In addition to the elements nominally present in the steels, analyses were made for residual phosphorus, sulphur, nickel, copper, molybdenum and chromium on one heat of those made with the same materials during the same period. Actual grain size was determined by microscopic examination of small samples quenched in water after receiving the same thermal cycle as the Jominy hardenability specimens. Chemical analyses, heat-treatment, grain size, and hardenability are shown in Table I representing three ranges of composition.

Jan 1, 1943

By Leo F. Reinartz

The history of steelmaking in the United States is a fascinating story of determination, sudden tragedy, exploitation, and inventive genius rolled into one gigantic plot. Mr. Reinartz' flowing interpretation of the progress made in the last one hundred years is being presented in a series of four articles. THIS is the Age of Steel. We live in a mechanized era. Our everyday lives--everything we see or do-are organized and influenced by this versatile metal. Our industries, our farms, our homes, and our transportation-yes, our vocations and avocations, or luxuries and necessities-all are dependent upon smelting iron and making steel. Take away iron and steel and soon our vaunted civilization would revert to a primitive existence. These metals, often in crude forms, have been known for thousands of years. Down through the ages, until about one hundred years ago, steel was made laboriously, and at high est, in small batches. During those years, methods of manufacture did not change very much. Over long periods of time only warriors, royalty, and wealthy people could afford to use articles made of iron or steel. History has recorded that the nations which were expert in iron and steel manufacture, and had access to rich iron-ore deposits, were the leaders in war or in peaceful pursuits. At the end of the 18th century, thirteen struggling American colonies had broken not only the political shackles that bound them to Great Britain, but also many of the economic bonds. They had showed their skill, Yankee ingenuity, and energy by making iron and steel articles for their own use. After the Revolutionary War, more and more hardy American pioneers pushed westward through the Allegheny Mountain passes and down the rivers into the fertile Ohio River and Kentucky country. Demands for articles made of iron increased. The iron industry on the east coast grew and prospered. As this trend continued, iron industrialists moved their plants westward to be near the large deposits of high-grade coal in western Pennsylvania, eastern Ohio, and nothern West Virginia. They also desired to use the local iron ores and water resources of those areas. Blast furnaces and ironworks were built in the Pittsburgh, Youngstown, southern Ohio, and northern West Virginia districts. In 1810, the United States produced 53,908 gross tons of cast iron and 917 tons of steel. Iron ore discovery A white man first discovered large deposits of iron ore in the northern Michigan and Lake Superior country in 1844. One year later, the Sault

Jan 1, 1961

By Lendall P. Warriner, Blandford C. Burgess

Jasper County lies just north of the geographical center of Georgia, bounded on the west and north by the Ocmulgee River. The county seat, Monticello, is approximately 65 miles east-southeast of Atlanta and 40 miles north of Macon. It is served by the Macon-Athens branch of the Central of Georgia Railway Co. and by five paved highways converging from adjoining county seats. Farming and lumbering are the principal local occupations. About half the county is covered with pine and mixed hardwoods; a large part of the forested land is owned by the Soil Conservation Service of the Department of Agriculture in its Piedmont Land Utilization Project. The topography is one of gently rolling field and forest with occasional hills rising 100 ft or more above the creek beds. Though annual rainfall is in the neighborhood of 60 in., most of it falls in torrential downpours of short duration which tend rapidly to erode the red soil and convert the country roads to greasy tracks of red mud. History The pegmatites of Jasper County produced a small amount of mica in World War I. In World War 11, our Government's search for this strategic mineral brought to Georgia B. C. Burgess, then Southern Manager of Colonial Mica Corp., subdivision of Metals Reserve Corp., who noted on State Highway 83 the presence of pegmatitic material used as road metal. In 1944, after severing his Government connection and returning to private practice, Mr. Burgess investigated the source of the pegmatitic material noted on his previous visit and discovered that graphic granite pegmatite had been mined for the road metal. He secured mineral leases from the Soil Conservation Service and from private owners and began preliminary development work. By 1946 he had uncovered enough pegmatite to warrant an enterprise to undertake economic development of the feldspar. In March 1947, he conveyed his leases and interest to Appalachian Minerals Co., remaining with it as Vice President and General Manager. This company has carried on additional development, removing overburden by bulldozer and drilling the pegmatites uncovered. A modern and efficient feldspar grinding plant to produce 20 mesh feldspar for the glass industry was completed and placed in operation May 1, 1948. Geology GENERAL GEOLOGY OF ROCK TYPES OTHER THAN PEGMATITE Jasper County lies within the Appalachian Crystalline Complex and approximately 40 miles north of the "Fall Line," where the Upper Cretace-

Jan 1, 1950

By H. C. Ray

ABOUT the beginning of 1930, coal preparation had reached the stage where the cleaning of coal by liquid or air had become the order of the day. Since that time many new preparation plants have been installed in spite of the years of depression in the coal industry, and this is indicative of a trend wherein the coal producer found it expedient to manufacture a cleaner product in order to compete with other fuels. It was also about 1930 that, because of the difficulties encountered with fine coal in cleaning plants, dust collectors came into use. Both cleaning plants and dust collectors, therefore, were much discussed at the engineering meetings of the early 1930's. During these meetings the many advantages to be gained through the use of dust-collecting systems were pointed out by Hebley,1 Appleyard2 and others. The great possibilities of new markets for this product were emphasized and discussed at the same time; however, the disposal of the collected dust remained a problem. Since the purpose of dust collecting is to improve the preparation and, consequently, the salability of the coal, it seems illogical to return the collected dust to any of the coal being prepared for market use, as is done in preparation plants that include dust-collecting systems. The logical thing is to dispose of the dust in some useful and practical manner outside of the tipple. As a practical matter, this can be done in one or both of two ways; either by consuming the dust at the mine's own power plant or by marketing the dust direct to the consumer. The latter method not only offers the greatest opportunities, but is the most important, because of inequalities that may exist between the quantity of dust collected and the consuming capacity of the mine's power plant. In considering the more important marketing possibilities, we are confronted immediately with the problems connected with the handling and transportation of so fine a material. It is this problem, rather than the problem of finding new markets, that has been responsible for the lack of progress in the matter of dust disposal. It is the purpose of this paper to point out again some of the potential market outlets, and also to describe an existing system of handling and transporting coal dust. To the best of the writer's knowledge, this is the first and only operation in this country that has handled fine-mesh coal in bulk 50-ton lots direct to the consumer. POtential Markets for Fine-mesh Coal Dust In general, the potential market outlets would include any operation of which the pulverization of coal is a necessary part. To be more specific, a few of the better known operations of this type must include: colloidal-fuel plants, briquetting plants, "sea coal" distributing plants, water-purification plants and, obviously, pow-

Jan 1, 1944

By R. P. Carreker

ONE of a series, this report is concerned with the experimental documentation of the deformation behavior of pure metals over a wide range of temperature. Previous reports in the series describe the creep behavior of platinum1 and aluminum2 and the tensile behavior of copper,&apos; silver,& and molybdenum.5 Subsequent reports will describe the creep behavior of copper and silver and the tensile behavior of platinum, thus providing extensive creep and tensile data on four face-centered-cubic metals tested under comparable conditions. Material Two lots of high-purity aluminum were used in this investigation. One lot, designated AC, was obtained direct from the Aluminum Co. of America as high-purity aluminum in notch-bar form. A typical analysis of this type of aluminum is 0.006 pct Si, 0.015 pct Cu, 0.006 pct Fe, and 99.975 pct Al. Lot BS was obtained from J. I. Hoffman of the Bureau of Standards as a portion of the Aluminum A described in his report of the redetermination of the atomic weight of aluminum.6 Lot BS originated with the Aluminum Co. of America also, and was received in the standard notch-bar form. A detailed chemical and spectroscopic analysis of lot BS has been published.6 Principa1 impurities were 0.006 pct Si, 0.003 pct Fe, 0.002 pct Cu, and >99.987 pct Al. Samples were processed identically by room-temperature swaging and drawing to 0.030 in. diam wires from approximately ½ in. diam rods that were machined from the notch-bar pigs. Samples were cut from the cold-drawn wire, placed in a grooved graphite block in groups of thirteen, and annealed in air for 1 hr at each of several temperatures, with the results shown in Table I. The two lots of aluminum responded quite differently to annealing, the behavior of aluminum AC suggesting that its grain growth was controlled by impurities. The recrystallization texture of aluminum of similar purity comparably treated has been reported as predominantly <111> fiber with some <100> fiber present.7 Testing Procedure The testing procedure and method of analyzing the data have been described previously.2,3 Annealed specimens of 5 in. gage length were tested in an Instron tensile testing machine at a constant head motion corresponding to a strain rate of 0.04 min-&apos; at a number of temperatures. Instantaneous tenfold rate changes were employed in some tests to deter-

Jan 1, 1958

By Harry Perry

In the United States the state mining laws enacted in the late 1800s were the first laws to recognize that an employer had a responsibility to provide the employee a place to work that met at least some minimum safety standards. The coal mining industry was also the first major industry in the United States to be regulated in 1952 by federal safety laws, although federal inspectors had the right-of-entry as early as 1941. Within recent years, however, the Congress has enacted a number of federal safety regulations for a variety of industries, such as the Aviation Act (1958), National Traffic and Motor Vehicle Act (1966), National Gas Pipeline Act (1968), and Radiation Control for Health and Safety Act (1968). The fatality and injury experiences of the mining industry in the United States, while at a significantly higher rate than for industry as a whole, showed a continuous improvement until the last decade or two-at which time the rate leveled off. Although fatality and injury rates in foreign countries have been generally lower than in the United States, further improvement in those countries also has been difficult to achieve in recent years. It appears, therefore, that some major change in mining laws, combined with a radical improvement in mining technology and a more effective labor-management safety program, will be needed if further reductions are to be achieved in fatality and injury rates. At the same time, there is a growing awareness by society that an employee&apos;s place of work, where he spends nearly half of his waking hours, should be made as safe as possible. As increased consideration is given to means for achieving greater safety in all industrial situations, it is becoming apparent that more is required than merely providing physical safeguards on tools and machines. Rigorous, strictly enforced safety standards are useful, but more important is the desire of labor and management to make certain that industrial accidents are prevented. The pressure to achieve increased productivity, and thus receive higher wages, can be a significant deterrent to safe working practices. The temptation can be great to "take a chance" or "cut a corner" in order to speed up production. Public concern over all types of industrial safety in the United States was reflected by the introduction of a number of general occupational health and safety bills in Congress for the first time in 1968. While no legislation resulted, the hearings revealed that, although there were differences in how standards should be set and who should administer them, there was agreement on the need for adequate laws. Since the mining industry has been subject to safety standards longer than other industries, it is not surprising that advanced safety concepts for mining are being explored by the industry and the enforcing agencies. More complete and sophisticated accident reporting is being planned that will reveal the

Jan 1, 1976

By Louis Moyd

In the preparation of illustrations to accompany reports of investigations concerning particle shapes of various natural and manufactured materials proposed for use as he aggretates in concrete structures, it was found that stereoscopic views of such materials presented the information much more effectively than the usual two-dimensional photographs. With the whole-hearted cooperation of the Photographic Section, a technique was developed in the petro-graphic laboratory of the Concrete Research Division, U.S. Corps of Engineers, at Clinton, Miss., for simple and rapid preparation of paired stereoscopic photographs and micrographs. The method requires only equipment which is usually part of the general stock of any laboratory, and it is adaptable for all purposes in which three-dimensional views would be found superior to ordinary photographs. Stereoscopic Photographs Where the subject or subjects to be photographed are small but not of microscopic size, an ordinary camera having a ground-glass focusing screen is set up vertically over the field. The material to be photographed is placed on a card, the surface of which is suitable as a background. The card is mounted so that it can be tilted about 5&apos; above and below the horizontal plane, on an axis that coincides with the north-south diameter of the viewing screen. A simple way of achieving this is to mount the card on an object having a convex lower surface. In our laboratory, a watch-glass has been used, with plasticene as the mounting medium. The convex surface should be mounted on a support having a round opening on top and a flat bottom. A roll of tape, a petri dish, a beaker, or any other piece of equipment having the proper shape to give stability to the setup will be satisfactory. The arrangement of the required equipment is shown in Fig 1. For the best results, the subject to be photographed should be mounted in the plane of the axis of rotation. To achieve this effect, the depth of the mass of plasticene between the background and the watch-glass is varied so that when the watch-glass is tilted back and forth on the axis, the subject to be photographed does not appear to move back and forth across the viewing screen. A permanent piece of equipment, embodying an adjustable vertical screw, with lock-nuts, could be made for this purpose. The subject may be illuminated in any manner desired. It was found that the presence of shadows intensifies the effect of depth. In taking the photographs, the concave surface is mounted so that one side of the background card is about 5&apos; below the horizontal, while the axis remains in the horizontal plane. The subject is focused carefully on the ground glass and a picture is taken. The card is then tilted so that the opposite side is about 5&apos; below the horizontal, while the axis still remains in the horizontal plane. The subject is again put in focus and another picture is taken. After both pictures are developed and printed, they are placed side by side in the same orientation and examined with a stereoscopic viewer. If depressions appear where there ought

Jan 1, 1950

By B. J. Harlan

The trying times experienced by the steel industry during the past four years have emphasized the necessity of producing pig iron at the lowest possible cost. The trend in both design and operation of blast furnaces has been toward this end rather than toward securing maximum production from a unit or group of units. In the following discussion the trend in design of stacks and auxiliary equipment will be taken up before operation is considered. Although few furnaces have been constructed in the past few years, the trend is definitely toward larger furnaces with a hearth diameter of 24 or 25 ft. Such a furnace is very flexible, being able to produce efficiently any desired daily tonnage between 500 and-1000 or more. The detail of the design of furnace stacks, with the exception of the top, has changed little in recent years. To decrease the velocity of gas through the throat of the furnaces, thereby reducing flue-dust losses, the stock-line areas are constantly being made larger. The top dimensions of the larger furnaces are usually as follows: Stock-line diameter, 19 to 20 ft.; large bell diameter, 14 to 15 ft.; straight section of throat, 5 to 10 ft. high; inwall batter, 1 to 11/4 in. Pe ft. The ratio between the area of the stock line and the area of the large. bell is usually about 1.85 to 1. The stock-line diameter of some smaller furnaces has been increased to that of the hearth diameter of the stack at the expense of the stack batter. Remarkable decreases in flue-dust production are claimed for the so-called " Venturi top," which is achieved by flaring the stock line, in the form of an inverted cone, from a diameter of 17 ft. at 10 ft. below the large bell closed to a diameter of 19 ft. 6 in. at 3 ft. below the large bell closed. Time alone will tell which of the two designs is the better. Because of differences in raw materials, one top may be better for some plants and the other top for other plants. In the search for lower costs and higher efficiencies all operators are, adopting stoves that will maintain maximum hot-blast temperatures with a minimum gas consumption. To meet these requirements, stove capacity of approximately 7 sq. ft. of heating surface and 1.8 cu. ft. of brick volume is required per cubic foot of wind blown per minute.

Jan 1, 1934

By W. H. Young, P. D. Torrey

The Eastern fields comprise a distinct geological and geographical unit, located in the northern part of the Appalachian geosynclinal prov-ince. In this area are the fields of New York, producing from rocks of Devonian, Silurian and Ordovician age; the fields of western Pennsylvania, where oil and gas occur chiefly in rocks of Mississippian and Devonian age; the fields of eastern Ohio, where oil and gas are obtained from rocks of Pennsylvanian, Mississippian and Silurian age; and the fields of West Virginia, where oil and gas are produced from rocks of Pennsylvanian, Mississippian and Devonian age. Many of these fields are of great antiquity in comparison to the age of the producing areas in a greater part of this country, and consequently in most instances it is impossible to obtain accurate historical statistics. In addition, the records of many of the more recently discovered fields are either unobtainable or are not sufficiently reliable to justify their incorporation in a review of this character. Rather than overemphasize certain fields and areas, where complete records are available, when there are many other fields of equal importance for which statistical data are not available, the authors have made a tabulation of development that does not take into consideration past operations and production. The records utilized in preparing this paper were derived largely from the scout reports of several of the larger companies, which generously made them available to the authors. These were independently tabulated by counties and townships, in order to eliminate as far as possible duplications and, excepting the Clinton fields of Ohio, where many of the smaller wells have not been individually reported, they represent the most accurate information available. Market conditions in both the oil and gas industry were far from favorable during 1932 and in consequence there was a total decline in drilling in the Eastern States, which is 22 per cent less than the number of completions in the preceding year. This decline was not constant over the entire area, as is shown in Table 1. The oil fields of both New York and western Pennsylvania were the scene of renewed drilling activity, which was largely restricted to the water-flooding operations in the Bradford and Allegany fields. Practically no new operations were started, but a certain number of new wells

Jan 1, 1933

By Zay Jeffries

The object of the present paper is to enlarge somewhat on the general principles advanced in my discussion1 of Mathewson and Phillips&apos; article on The Recrystallization of Cold-Worked Alpha Brass on Anneal-- ing.2 It will also serve as an acknowledgment of Prof. Howe&apos;s most important remarks on my contribution. In this paper the writer has adopted Prof. Howe&apos;s suggestion to substitute the term "germinative temperature&apos;&apos; for "critical temperature for grain growth." Instead of being an exact or certain temperature it should be considered that the germinative temperature phenomenon exists throughout a small temperature range. v Factors Influencing Fast Growth Phenomena The development of grains of macroscopic size at the germinative temperature should be considered the extreme condition of a general rule. When considered in this light it is not strange that the development of these large grains should be the exception and not the rule. The principal factors influencing the operation of the laws of fast growth temperature are as follows: . 1. Rate of heating. In the original paper,&apos; the germinative temperature was defined as "the minimum temperature at which two adjacent grains can coalesce to form one larger grain, provided that this larger grain will have sufficiently increased its power of attack, to enable it to absorb adjacent grains which cannot coalesce with each other. Time is always to be understood as a factor governing the first stage of grain growth." If the time of heating is short, the germinative temperature is raised. The formation of large grains in metals may occur at relatively high temperatures when the rate of heating is rapid. It is to be understood that in such cases, grain growth

Jan 1, 1917

By E. A. Gulbransen, W. S. Wysong

THE behavior of molybdenum and its surface oxides in oxidizing and reducing gas atmospheres and in high vacua at elevated temperatures is a question of scientific and technical importance The use of molybdenum as a metal or as an important component in alloys in oxidizing atmospheres at elevated temperatures has been limited because of the unprotective nature of its oxide film and the volatility of this oxide at moderate temperatures. This communication will present results of a vacuum microbalance study 1,2 of the following problems. (11) the oxidation kinetics in the temperature range of 250° to 450°C; (2) the reduction with pure hydrogen of thin oxide films formed on molybdenum; (3) the volatility of the thin oxide films, and (4) the vacuum oxidation of molybdenum at high temperatures. Molybdenum is an interesting metal to study for the following reasons: (I) although the oxide-to-metal-volume ratio is greater than one, the metal is not considered protective; (2) the metal oxidizes readily at temperatures of 250°C and higher; (3) the oxides of the metal are reduced at temperatures as low as 500°C by pure hydrogen; (4) the oxide MoO3 melts at 795°C; and (5) the oxides of molybdenum are volatile at moderate temperatures. The following variables are studied in the oxidation kinetics. time, temperature, pressure, surface preparation, surface area, concentration of inert gas in the lattice, cycling procedures in temperature, vacuum effect and high temperature vacuum oxidation The general interpretation of many of these factors has been previously discussed. LITERATURE The oxidation of molybdenum has not been studied critically. Although" many studies have probably been made on the kinetics of the oxidation process, none has been reported in the literature available to us. The crystal structures found in the oxidation of molybdenum have been studied by Hickman and Culbransen 4 Their results showed that MoO2 is the oxide which is stable in contact with the metallic subgtrate throughout the temperature range 300 to 700°C. As the film thickens in the low temperature range, MoO3 becomes predominant on the surface. Above 400°C, Mo03 is no longer observed, Mo02 being the only oxide found. Hagg and Magneli5 have shown from an X ray study that the a-phase, orthorhombic MoO3 is stable up to 1050°C. Two other phases, ß and ß&apos;, with compositions close to Mo02 90 are also obtained The formula for the ß phase is not given but that of the ß&apos; phase is defined as Mo9026. The ß&apos; phase is found to be built upon a monoclinic unit cell. A -?-phase is isolated from a preparation M00275 heated for 17 hrs at 670°C. This phase is

Jan 1, 1947

By M. C. Cheney

The active development of the vast East Texas oil field, the attendant effects of the rapidly increasing flow from its prolific wells and the efforts to bring order out of chaos precluded or dwarfed other oil development in Texas during 1931. In a paper by Dr. F. H. Lahee1 presented at the October, 1931, meeting, the early history of the East Texas oil field is described and the sequence of events in connection with its development and efforts to control its production up to Sept. 25 is narrated. At that time the Railroad Commission of the state reduced the production of the field to a maximum of 400,000 bbl. per day by restricting the allowable daily production per well to 185 bbl. By further reduction in the daily production per well to 100 bbl., the field was held below that maximum figure during the remainder of the year. Meanwhile, as a result of an injunction against the Railroad Commission, its authority in the field was superseded on Oct. 13 by the Governor of the state, and after that date production was controlled directly by his orders issued under authority of martial law. Suits to contest this authority were brought in the Federal courts and were pending at the close of the year. On March 5, 1931, as a result of the East Texas production, posted prices for Mid-Continent 40&apos; A.P.I. crude slumped from $1.07 to $0.67. As East Texas production continued to mount, posted prices in East Texas were reduced to $0.37 on June 3 and $0.22 on July 8, although in that field most of the oil was sold for much less, bringing the producer and royalty owner as low as $0.025 per barrel. Northeast Texas To the information contained in Dr. Lahee&apos;s paper, it can now be added that the East Texas field has produced over 105,000,000 bbl. and registered about 3700 successful completions during 1931. There may be some merit to the recent prediction that a large part of the field will have passed its flowing period by the middle of 1932 unless

Jan 1, 1932

By Peter R. Morris, Alan J. Heckler

THREE angles are required to specify the orientation of a crystallite with respect to a physical reference frame. The distribution of crystallite orientations in a polycrystal is thus a function of three angular variables. The most widely used experimental techniques for studying orientation in polycrystals lead directly to the pole figure representation, i.e., the distribution of the poles of certain crystallographic planes in terms of two angular variables. In recent years1-5 methods have been developed which permit determination of the (three-angle) crystallite orientation distribution from several (two-angle) pole figure distributions. In this work Roe&apos;s method has been applied to the study of orientation in hcp materials. The method is illustrated for commercial purity titanium sheet (Ti-70) which was cold rolled (65 pct reduction), annealed at 1450°F for 3 min, and air cooled. The grain shape was observed to be equiaxed after this treatment. EFFECTS OF PHYSICAL, CRYSTALLOGRAPHIC SYMMETRY In Roe&apos;s method the crystallite orientation distribution, w(?,?,F), is expanded in a series of generalized spherical harmonics 11(?,?,F) = E E E W^Zirmtye-tote-in* [l] 1=o ,,,=-I ,,=-I where { = cos 8. The set of Euler angles employed here is illustrated in Fig. 1. The axis for each rotation is denoted by a double arrowhead. The positive sense of each rotation is that of a right-handed screw advancing in the direction of the double arrowhead. The X, Y, and Z directions correspond to the rolling direction, cross direction, and normal direction, respectively. In the initial orientation (10.O), (12.O), and (00 . 1) planes are perpendicular to the X, Y, and Z directions, respectively. The IC/ rotation about the Z axis is carried out first by rotating X into X&apos;, Y into Y&apos;, and leaving 2 unchanged, i.e., Z&apos; = Z. The 8 rotation about the Y&apos; axis is carried out second by rotating X&apos; into X", 2&apos; into Z", and leaving Y&apos; unchanged, i.e., Y" = Y&apos;. The I$ rotation about the Z" axis is carried out last by rotating X" into X"&apos;, Y into Y"&apos;, and leaving 2" unchanged, i.e., 2"&apos; = 2". Any specified orientation of the X&apos;", Y&apos;", and Z&apos;" crystal-fixed axis system relative to the X. Y, and Z physical axes (rolling direction, transverse direction, and sheet normal direction, respectively) can be obtained by appropriate IC/, 8, and (F rotations. The Zl,, of Eq. [l] are the Jacobi polynomials, augmented by the square root of the weight function. The Zl,, are symmetric in m,n, i.e., Zl,,= Zlnm. For orthotropic physical symmetry and hexagonal crystallographic symmetry, the coefficients, W!,,, of the series are all real, W!mn = Wzfi, = Wlm~ = Wlfi~, 1 and m are even and n is restricted to 6k, where k = ...,-2,-1, 0, 1, 2, .-.. The determination of the Wlmn from pole figure data has been previously described.&apos;~~ The Zl,, may be written in multiple angle form

Jan 1, 1970

By Herman Garlichs

THE development of the extensive Southeast Missouri deposits greatly preceded that of the Iowa and Wisconsin deposits. It began about 1720 at Mine La Motte and other localities, and has continued uninterruptedly to the present time. It is estimated that this district produced about 184,000 tons of lead in the year 1916, having a value of approximately, $25,000,000. This is a new high record. The Southwest Missouri orebodies were hardly known before 1845 and were not extensively developed until 1870: Lead production in South-west Missouri for 1916 was 38,788 tons. Oklahoma produced 14,399 ,tons and Kansas 2,345 tons, making a total for Southwest Missouri, and the adjoining districts in Oklahoma and Kansas, of 55,532 tons of lead. The first metallurgists in Missouri were the Indian and the hunter. The early settler learned to procure his bullets either by melting ore in his camp fire or by throwing pieces of galena on an old stump and depending on the usual roasting and reaction method to obtain the metal. A little more refined method was to arrange two flat stones in the form of a V. Wood and galena were placed in the furnace and ignited. As heat developed, some of the metal was extracted and molded into bullets. The next step in utilizing the lead ores was the log hearth. All lead in Missouri was smelted in this crude affair before 1820. It was built on sloping ground, and consisted of a hearth of stone, surrounded on the front and two sides by a stone wall. The wall was 7 ft. high in front. The top and rear end were left open and in front an arch or opening was made, forming the eye of the furnace. In front of this a pit was dug in the ground, to receive the molten metal. Large logs were rolled in at the back and made to rest upon ledges formed inside, to raise them from the hearth and to give a draft. These logs filled the entire width of the furnace. Small split logs were then set up around the two sides and the front, and the ore was piled on until the furnace was full. Finally, the mass was covered with logs and fuel until the ore was completely surrounded. A gentle heat was started, which was raised very gradually. After 12 hr. the heat was increased and continued for 12 hr. more, 24 hr. being required, for each smelting. The furnace treated about 5,000 lb. per 24 hr. and the ore yielded about 50 per cent. of its metallic lead. A considerable quantity of the ore was not desulphurized, and fell between

Jan 7, 1917

By R. S. Shoemaker, F. W. McQuiston

RECOVERY METHODS AS RELATED TO PROPERTIES OF SILVER ORES The earliest metallurgical process for treating silver ores was amalgamation with mercury which was in use in the early 1500&apos;s. Closely following was the development of the Patio process for treating ores at Pachuca, Mexico. Silver often occurs as the native metal and in deposits associated with other metals such as gold, copper, lead and zinc. Principal silver minerals include compounds of sulfur, antimony, arsenic, and copper. Silver chloride, and argentiferous galena are also prime sources. Native silver and the chloride characterize the oxide zone of most deposits. Native silver can be concentrated, amalgamated, or cyanided. Silver chloride rapidly dissolves in cyanide without oxygen. Oxidized silver ores containing the higher oxides of manganese are generally refractory to metallurgical treatment. A refractory compound of manganese and silver is formed, probably a manganite , which is insoluble in cyanide solutions. Argentite is the predominant silver mineral. Other important economic minerals are native silver, argentiferous galena, cerargyrite, pyrargyrite and tetrahedrite. Argentite dissolves slowly, the reaction being reversible requires an excess of cyanide. Argentite with disseminated fine grained gold occurring in quartz veins with minor amounts of chalcopyrite and galena may be cyanided directly after grinding, with high silver and gold recoveries. The flowsheet adapted to this type of ore is the Minas de San Luis, Tayoltita cyanide plant, which treats a high grade argentite silver ore containing gold. It is a standard cyanidation circuit but employs long periods of agitation contact for the high silver sulfide content ore. Lead-zinc base metal semi-oxidized- complex ores in pipes and chimneys are replacement deposits in limestone at El Mochito Mine, Honduras. Mineralization comprises galena, cerussite, anglesite, sphalerite, calamine, and smithsonite. The silver content of about 16 ounces occurs as native silver globs, wire and the mineral argentite. After flotation of lead and zinc concentrates, the tailings are cyanided for gold and silver recovery. The great Huelva pyritic copper deposits of Spain carry a little gold and silver. At Cerro Colorado, these metals were concentrated above the chalcocite zone into the so-labeled Mgossanu. This material with a content of 0.08-0.09 oz Au and 1.50 oz Ag per ton is amenable to cyanidation. See Cerro Colorado flowsheet. In southern Hidalgo, about 60 miles north of Mexico City, are the great silver--gold veins of one of the foremost silver mining districts of the world. Real del Monte, Pachuca. The mineralized area consists of flow rocks and intrusives. The oxidized ores carry pyrites with oxides of iron and manganese and other minerals, silver and gold. The first zone contains

Jan 1, 1975

By A. K. Knickerbocker

Practically all underground work on the Minnesota iron ranges is done by miners working on a so-called contract wage system. This system, while it has certain advantages over the straight day&apos;s pay or company-account method of wage payment, has serious and vital defects. In view of the scarcity and demands of labor, it is important that employers of labor scrutinize their systems of wage payments carefully, not only to save losses and trouble, due to labor disturbances, but also to secure the greatest efficiency of their workmen and reduce their operating costs. It is admitted that an adequate, just, and equitable wage is the prime factor in bringing about these benefits. The wage of labor and its method of application and payment have been, and always will be, the main factors in the unrest and dissatis. faction of labor. Not only does labor want and need an adequate wage, assuming that work is adequately performed, but it wants and is entitled to a just and equitable wage. Labor must have respect for the fairness of the wage and for the fairness of the management in the application of the wage It is conceded that the Minnesota iron miners are now, and have been, in the main paid adequately, but the inherent defects of the so-called contract system prevent any just or equitable application of this wage to the various units of the labor body. The defects of the contract system, with its obvious inequalities, favoritisms, and injustices, are cancers in the brain of labor. Every thinking miner realizes these defects and knows just what they are; the unthinking do not realize the details of the subject, but each month they are forcibly reminded of these defects through the pay envelope. As practiced on the iron ranges, however, the so-called "contract " system is not a contract and the name is a misnomer. No true contractual obligation exists. As usually practised, the contract system involves the setting of a price per foot in development work, or per foot or per car, usually the latter, in slicing or stoping, by the mining captain, and assumes its acceptance, though often under protest, by the men. A price is set for each working place, in which there are usually two men per shift. This price includes labor and supplies, such as explosives, fuse and caps, shovels, carbide, etc., and the men divide the total earnings less the amount expended for supplies. The cost of the supplies charged to the men varies

Jan 1, 1920

By Sylvan Z. Beer

The factors that determine the yield and crystal size in the two-temperature synthesis of A lp were examined. Low yields and small crystals were associated with low temperatures and pressure. Attempts to grow large crystals in the critical and supercritical region of phosphorus were unsuccessful. Crystal size increases markedly at elevated temperatures. Crystals grown at temperatures as high as 1450° C fluo-resced, under uv excitation, at energies close to the estimated band gap of about 2.4 ev, while crystals grown at lower temperatures tended to fluoresce in the red region of the spectrum. Those grown in the supercritical region showed no ALP fluorescence. Heating the high-temperature-grown ALP under vacuum greatly increased its fluorescence efficiency and moved the emission peak to higher energies. I HE III-V compounds, with few exceptions, have been prepared by the two-temperature method. In its classic form this technique is applicable to closed systems where at least one of the components, in this case the column V element, is a liquid or a solid with a high vapor pressure. One advantage of this method over flow systems is in its simplicity. In addition, because it is a closed system, it can, under the circumstances to be described later, be run at higher pressures of the volatile species than in flow systems. In instances where the III-V compound is soluble in the parent III metal to about 1 mol pct or higher, solution growth can be made to take place by slow cooling. This, for instance, is one way in which single-crystal GaP1 and Inp2 have been grown. Initial attempts to synthesize and grow A1P by this technique were not too successful; the yield was low and the crystals obtained were exceedingly small. The conditions required for improving the yield and growth by this technique were, therefore, sought. Two obvious conditions which could be controlling were examined. These were the temperature of the aluminum and the pressure of the phosphorus. The range of temperatures studied extended from about the melting point of aluminum, 660° to about 1450°C. The latter is dictated by the vapor pressure of aluminum which reaches about 1 Torr at that temperature and the limitations of the materials of construction as described in the next section. The pressure range of interest covers from below 1 atm to above the critical pressure of phosphorus, 82.2 atm. EXPERIMENTAL The Temperature of Aluminum as a Variable. A series of experiments were run in the conventional two-temperature manner. All refractories and quartz were dried by heating at 800° to 900° for a minimum of 24 hr, and usually much longer, before use. The aluminum

Jan 1, 1969

By Gail F. Moulton, C. E. Shoenfelt

Proven and developed oil reserves, and productive capacity increased during 1943 in the fieids of the Rocky Mountain region. Oil production during the year was nearly 45 million barrels, or slightly less than in 1942. The rate of production at the start of 1944 was slightly less than at the start of 1943. Pipe-line projects scheduled for completion during 1944 should permit a substantial increase in the rate of production. Wildcat exploration was more extensive in Montana during 1943 than in other states in the region. The results of wildcat drilling were unsatisfactory, although new oil fields were discovered on the Gebo, Little Buffalo Basin and Steamboat Butte structures of Wyoming, the Gage anticline of Montana, and the Clark Lake structure of Colorado. The area of the structures on which the discovery wells were drilled is known to be considerable, but further drilling is required to determine the importance of these fields. The most important increase in proven reserves resulted from the drilling to newly discovered deeper producing formations in the Elk Basin and other fields of the Big Horn Basin area of northern Wyoming. Lack of a market and unfavorable prices for heavy black oils had prevented complete exploration of favorable areas in the Rocky Mountain region for many years. In particular, the effect on further exploitation of the Big Horn Basin area had been quite serious. The increased demands for all oils created by the war and an increase in price in February 1943, combined later with Government approval of construction of pipe lines from the Big Horn Basin area to the Billings and the Casper districts, provided a basis for undertaking a drilling program. The important additions to reserves were made by drilling in previously discovered fields. The newly discovered fields resulted from drilling on favorable structures which had been known for several years. A continuation of the favorable results obtained during 1943 seems possible only if further testing of the newly discovered fields is satisfactory and if drilling on less favorable known structures or geophysical prospects results in the discovery of new fields. The amount of drilling in the Rocky Mountain states of Colorado, Montana and Wyoming, was about the same during 1943 as .in 1942. However, owing to the fact that a number of wells of large potential production were completed in the Elk Basin field, the total initial production of the prodicing wells was- nearly twice as great for 1943 as for 1942. Explorational activity at the end of 1943 seemed to be directed to geophysical methods, which are required to discover structures hidden beneath the rocks of Tertiary age in the Powder River and other large sedimentary basins. It is in

Jan 1, 1944