Search Documents

By Albert J. Phillips

LEAD is an inexpensive metal produced and consumed in large quantities with certain chemical and physical properties that permit handling the molten metal in bulk. These properties are its low melting point, resistance to oxidation, and its negligible solvent action on iron and steel. Thus, lead is almost always melted in large iron or steel kettles, heated from beneath, and is seldom melted in either directly or indirectly fired furnaces or electric induction or arc furnaces. Even with a modest operation a kettle holding 2 or 3 tons is employed, and the size will range up to 215 tons in the large lead refineries. The methods of handling tin and its alloys are essentially the same as for lead because of the similarity in melting point and resistance to oxidation, although because of the cost of the metal the scale is more modest. In melting lead and its alloys preliminary to a casting operation it is seldom that the melting unit is completely drained of its contents. The usual procedure is to continuously charge solid metal and continuously remove small amounts of liquid metal, so that the kettle is maintained essentially full at all times. For type metals, linotype machines usually employ automatic means of adding the solid alloy to the melting pot in proportion to the removal of the liquid metal in casting slugs of type. In the casting of grids for storage batteries, frequently automatic means of charging solid metal in direct proportion to the consumption of liquid metal in the casting is used. In the manufacture of bearing alloys, new alloy is charged in direct proportion to the consumption of metal in the bearings being cast, so that at no time does the level of the metal in the melting pot lower to any great extent. Even in the manufacture of bulky commodities such as pipe, cable. sheathing, and slabs for rolled sheet, it is the practice to employ a melting kettle of several times the capacity of the casting being made. A substantial level of liquid metal in the melting kettle is thus maintained even after the casting is poured and the original metal level is quickly restored by promptly charging new metal, even though there is no immediate need to proceed with additional casting. This procedure is permissible because the amount of fuel consumed in keeping the lead molten and immediately available for use is negligibly small and the cost is more than offset by the convenience. However, this convenient procedure necessitates study and control of certain properties of lead and tin alloys that are not of serious consequence in most other alloys and for that reason are not well known. These properties are "drossing rates" and "melting segregation." DROSSING RATE Users of lead long ago observed that the rate of dross formation on the surface of the lead in their kettles or pots varied greatly from time to time. This was particularly common in places where both antimonial lead alloys and commercially pure lead were being handled.

Jan 1, 1946

By D. W. Frommer, M. M. Fine

Mineral dressing research showed that iron concentrates of commercial quality could be produced from the Pea Ridge deposit near Sullivan, Mo. Magnetic separation and flotation, on a laboratory scale, yielded concentrates ranging from 60.0 to 71.4 pet Fe at recoveries of 89.9 to 97.6 pct. Early in 1957 St. Joseph Lead Co. announced discovery of three new centers of iron ore deposition in east central Missouri.' The discovery resulted from exploratory drilling in the vicinity of a magnetic anomaly or high. A deep hole, drilled into the Pre-Cambrian porphyry to determine the cause of anomaly, penetrated a magnetite-rich deposit.' The magnetic surveys that revealed the anomalies were begun by the Missouri Geological Survey in 1929 and were continued into the 1930's.3 At that time an area in Crawford County known as the Bourbon magnetic high was located. A second anomaly, similar in size and intensity, was discovered about six miles to the northeast in Franklin County in the vicinity of Sullivan. This area was not studied in detail until the early 1940's. To determine the cause of the anomalies, the USBM drilled four holes at the Bourbon site in 1943-1944.4 The most productive hole penetrated four mineralized zones having a total thickness of 127.5 ft. These zones contained magnetite in rhyo-lite porphyry at depths between 1600 and 2000 ft. Additional iron ore below 2000 ft was considered a possibility at the time. Some years later, the USGS, Missouri Geological Survey, St. Joseph Lead Co., and others cooperated in sponsoring an aeromagnetic survey of the Bourbon-Sullivan area which resulted in discovery of a third high, about eight miles distant at Pea Ridge. This deposit, with an estimated reserve of 50 to 100 million tons of iron ore, is considered the main find, although other orebodies in the same general area are of definite interest.' When this discovery was announced, St. Joseph Lead also revealed plans to exploit the deposit jointly with Bethlehem Steel Co. A new corporation, Meramec Mining Co., was established, and 1962 was set as the target date for completing physical plant.2 Annual production goals of 2 million tons of beneficiated and pelletized iron ore were proposed. Preparation of the site for shaft sinking was begun in June 1957. Orebody and Character of Samples: Drilling to date has established the Pea Ridge orebody as a crescent-shaped pipe about 300 ft wide. Some drillholes were bottomed at 2800 ft in very good iron ore.6 he orebody is predominantly magnetite, although hematite and a mixture of hematite and magnetite occur in the upper areas and peripheral walls. Drillhole cores representing ore from different areas and depths of mineralization were grouped into composites for testing. These composites consisted of: 1) medium grade mixed hematite and magnetite, 2) high grade mixed hematite and magnetite, and 3) high grade magnetite. The medium grade ore came from three holes with depths of i350 to 1900 ft. The high grade mixed hematite and magnetite cores came from the 1790 to 2812-ft interval of one hole. Partial chemical analyses of the three samples, given in Table 1, reveal that all are excessively high in phosphorus and sulfur, and sample 1 is

Jan 1, 1960

By Jerome Alexander

THE object of this paper is to show that many of the important phenomena of metals and alloys are due to the facts that, at some stage, metals and alloys, or some of their constituents, are in a colloidal state and that a portion of the metal or alloy tends to remain in this state. The so-called amorphous phase in pure metals is an isocolloid, consisting of colloidal groups of metal molecules that may be dispersed in still more finely subdivided metal; these colloidal particles are not truly amorphous, but may consist, in part, if not entirely, of ultramicroscopic crystals; as a result the expressions amorphous phase and amorphous theory might be replaced by the expressions colloidal phase and colloidal theory. Any substance is in the colloidal state when the constituent particles consist of molecular or atomic groups, whose size varies approximately from about 100µµ down to about 5µµ, that is from just below the limit of microscopic resolvability to the dimensions commonly ascribed to the larger molecules. Colloidality involves no assumption as to the shape, internal structure, or orientation of the colloidal particles; size alone is the critical factor. A colloidal system may therefore contain crystalline groups, or amorphous groups (non-crystalline, random or haphazard clusters), or a mixture of the two. All colloids consist of at least two phases, the subdivided substance, or dispersed phase, and the substance into which this is subdivided, the dispersion medium. It is not necessary that there be any chemical difference between the dispersed phase and the dispersion medium. As molecular forces are extremely powerful, their application may produce marked changes in the physical properties of metals. It is doubtful whether metal in the interior, especially of large masses, possesses the same properties as that on or near the surface, which alone is open to, inspection.

Jan 10, 1920

By Waldemar Lindgren

The following pages present data accepted by many geochemists and geologists regarding the succession of minerals and the temperatures of formation in ore deposits affiliated with igneous rocks. They also present the individual views of the author on the composition of the solutions that were active and on the mode of deposition. He does not regard these views as speculations or hypotheses but as forming a well motivated and consistent theory. It is not certain, however, that all investigators will subscribe to them. Introduction The mining engineer may not always be interested in the field of stability and temperature of origin in the mineralogy of ore deposits, but he certainly is interested in the succession of minerals because this has a definite bearing on the understanding of the ores and on the best processes of extraction. It is proposed, therefore, to summarize in plain language the principal features of succession as shown in metallic ores. Chemical analyses of ores are always important, but the real knowledge of succession—sometimes called paragenesis-—of ores has been gained only in the last 20 years, by the study of polished sections. The study of hand specimens threw much light on the subject—as shown, for instance, by Breithaupt, whose "Paragenesis," written a hundred years ago, is still useful—but the results have been modified by our slowly gained understanding of the processes of replacement. Indications of Temperature Melting Points.—In the first place, a distinction must be made as to whether the ore is a product of magmatic consolidation, of pegmatitiza-tion or of hydrothermal activity. Most of the ores fall in the latter class. In any case, the melting points, although of importance, are not definite indications. In a magma the oxides and sulfides are likely to be among the earliest crystalline products (magnetite, ilmenite, zircon, corundum,

Jan 1, 1937

By L. M. Barker, E. G. Lewis

THE literature of milling is replete with papers devoted to the subject of ball milling, all of which no doubt have contributed in one way or another to progress in that art. In this paper reference will be made to only a few of the many authors, but the value of the contributions of all who have written on that subject is hereby acknowledged. With a few exceptions the efforts of most students of the subject have been devoted to laboratory investigations of principles. Davis1 was one of the first to report on plant-scale investigations and to present to mill men certain criteria for the guidance of ball-milling practices. His conclusions with respect to the significance of sizing analyses of classifier sands in their relation to the factors of mill speed and ball sizing are particularly referred to. Those conclusions were: I. If the balls are large or the speed of the mill is high, crowding will appear at the finer sizes in the classifier sands. 2. If the balls are small or the speed is low, crowding will appear at the coarser sizes in the classifier sands. 3. The indications are that best efficiency is obtained when the screen analysis of the sands show a minimum crowding at any size. The last conclusion was qualified by the statement that it had not been proved conclusively. It is surprising, however, that the literature of later years reveals little evidence that millmen have made any serious attempt to apply those criteria. This may, perhaps, be explained by the fact that the average plant-scale ball-milling problem presents so many variables that an investigation of any one of them encounters the problem of control of the others-a problem that often is unsurmountable in a small plant. In a large plant, in which there is a duplication of grinding units in parallel operation, opportunity may be afforded for determining the value of such criteria. Nevertheless, a study of published data from grinding circuits of both large and small plants suggests that either Davis' criteria have been tried and found inapplicable or have never been given consideration. For the purpose of testing Davis' conclusions and with improvement of ballmilling efficiency as the final objective, a test program was initiated in the concentrator of the New Cornelia branch of the Phelps Dodge Corporation early in 1938. The practices of that plant have already been described.2 The fine-grinding units are arranged so that any one of eight units may be operated as a test unit and its results compared with those of the remaining units. All units receive similar feed from a common storage bin, in which the product of the fine-crushing plant is bedded by traveling tripper. The ball mills are all similar in size and operated at the same speeds, and are individually metered. The feeder conveyors of each unit are equipped with Merrick weightometers. The test program as initially outlined proposed investigation of the following:

Jan 1, 1941

By Carl F. Floe, Michael B. Bever

THE possibility that carbon may be soluble in copper to a limited extent has been recognized for over a century. The quantitative investigation of this problem, however, requires more sensitive techniques than have formerly been available. Three recent developments have made possible more accurate determinations: the vacuum-fusion method of analysis, the production of copper of high purity and the availability of high-purity refractories, particularly graphite. In addition to its obvious theoretical interest, the problem of carbon solubility in copper is of practical importance. In the production of copper and of high-copper alloys, carbonaceous covers are frequently used. If even minute amounts of carbon are dissolved, insoluble carbon oxide gases will be formed when such metals are poured under oxidizing conditions. A mechanism of this kind could well be one of the principal causes of gas porosity in casting copper-base products. REVIEW OF LITERATURE In 1823 Vivian1 raised the question as to whether copper by overpoling becomes "combined with a minute portion of carbon." Karsten2 asserted, in 1832, that carbon reduces the high-temperature strength of pure copper, so that when the carbon content has reached 0.2 per cent the metal will be brittle at a dark red heat. According to Karsten, carbon contents of o.05 per cent make it difficult to hot-work copper. He also reported that the specific gravity of copper is 8.8969 and that it increases to 8.92 58 if the copper is cemented with carbon and then melted. He emphasized the difficulty of determining analytically the small amounts of carbon present in copper. The metal was removed by wet methods and the residue considered as carbon. At Percy's request, Dick,3 in 1856, carried out various working tests on copper that had been in prolonged contact with carbon, and found that the working properties of the metal had not been affected. He also attempted to determine the presence of carbon analytically. In one experiment the copper was dissolved and the residue was fused with litharge, and in another essentially a combustion analysis was made on a copper sample. In a final experiment, a sample was dissolved and the residue subsequently subjected to a combustion analysis. Indications of as much as o.005 per cent carbon were found, but Dick considered his work inconclusive largely because of the possible interference of sulphur. Percy4 concluded, from Dick's experiments and from some experimental work of his own, that the solubility of carbon in copper had not been established with

Jan 1, 1945

By J. Eric Belford

The Kidd Creek orebody is a massive base metal sulphide deposit with surface dimensions of 168 m by 670 m. The steeply dipping ore- body has been evaluated to a depth of 1 524 m. To date, the mining of the orebody has been divided into three stages. The first stage of mining was an open pit operation which supplied ore from 1966 until 1977 when a depth of 219 m was reached at the widest or north end of the orebody. The second stage of mining, called No.1 Mine, was the development of an underground mine to replace the pit and recover the ore from the floor of the pit to a depth of 792 m. Development of the underground mine started in 1969. Full production of 273 000 tonnes per month was attained in 1977. The third stage of mining called No.2 Mine, was initiated to accommodate a production expansion and included the development of a second underground mining operation to recover the ore from the bottom of No.1 Mine, i.e. the 2600 level; to a depth as yet undetermined but most likely the 4600 foot level. Development of the No.2 Mine began in 1974. Full production of 91 000 tonnes per month will be achieved in 1982. The choice of the 2800 level as the partition between the two underground mines was based on the following factors: The 2600 level is the lowest level which can conveniently be mined through the No.1 Mine crusher on the 2800 level. Development and trial stoping methods for mining at depth could be evaluated in the 2600 to 2800 block utilizing the existing hoisting facilities of No.1 Mine. Early development of the ore in the 2600 to 2800 block would provide additional mill feed sooner than could be achieved by developing from No.2 Shaft. The underground mining plan then is to mine from the pit floor down to the 2600 foot level and at the same time mine from the 2800 level down to at least the 4600 foot level. PLANNING The Kidd Creek operations are designed to follow a logical mining sequence. The grade of ore supplied to the concentrator is the result of following the mining plan. The philosophy of mining has been to mine downward in horizontal slices. In the case of No.1 Mine the slices are 122 m thick while in No.2 Mine the slices will be 183 m thick. The point of this approach is to mine the pillars immediately after creating them rather than allowing them to stand, deteriorate and generate uncontrollable situations. Two types of ore are handled separately to optimize recoverable values in concentrates. The 'A' type ore is a copper zinc ore with some silver and little lead. The 'C' type ore is a zinc silver ore with some lead and copper

Jan 1, 1981

By T. Egleston

THE manufacture of charcoal in kilns was declared many years ago, after a series of experiments made in poorly constructed furnaces, to be unprofitable, and the subject is dismissed by most writers with the remark that in order to use the method economically the products of distillation, both liquid and gaseous, must be collected. It is asserted with truth that the number of kilns required for a large production of iron would be so great that it is doubtful whether any works would be justified in making the necessary outlay for their construction, but it can also be asserted with equal truth that for any such production in a given locality the use of charcoal as fuel would be equally unjustifiable. It appears to have been forgotten that there were other manufactures besides iron in which large amounts of charcoal were used, but these consumers seem to have been guided entirely by the results of the experiments of the iron men, who necessarily made the largest quantity of it. Some authors speak in a doubtful way of the quality of the charcoal produced, and a few concede that with great care good charcoal can be made in kilns, but that most of the workmen do not like kiln charcoal. This is the real secret of the opposition to this method of manufacture. Most of these objections were written when charcoal was the most important fuel used by the iron manufacturer, and when what was a large production of iron for several furnaces was less than that produced by a single modern one, in localities where other fuels can be had. Almost all that has been written on the subject related to the use of the fuel for the manufacture of iron in the blast furnace, where very peculiar properties are required, and where the quantity produced is limited by the height of the furnace, and this in turn by the crushing resistance of the charcoal. A large production was, therefore, only possible when the best and hardest woods were used. Of all these objections there is not a single one which is not equally applicable to any method of charcoal manufacture, whether it be meilers, pits, or furnaces. Until recently, therefore, the manufacturers of charcoal iron * Read at the Pittsburgh meeting, May, 1879.

Jan 1, 1880

By Wm. D. Owsley, R. E. Moeller

In the petroleum industry, the process known as oil well cementing is the equivalent of pressure grouting in the mining and construction industries. The science of oil well cementing has been known and practiced for many years. At the present time it has been brought to a high degree of perfection in the handling of many different types of jobs, all of which are known as oil well cementing. In order to understand more easily these processes, we will discuss briefly several different types of oil well cementing jobs, the purposes for which they are performed, and the methods of their accomplishment. It is believed that some of .these procedures, in a modified form, can be applied to pressure grouting projects in general. Originally, oil well cementing consisted of placing a neat cement slurry about a steel casing set in a bore hole. Cement is used about these casings to protect them from the corrosive effects of ground waters, to protect the oil and gas zones from encroachment of undesired water from other levels, to prevent the blowing out of high pressure oil and gas zones from shallow levels, and to strengthen generally and support the casing being placed in the bore hole. After the bore hole is completed to the desired depth, casing is run into the well, pumps are attached to this casing and circulation of the mud fluid in the hole is established; this circulation being from the inside of the casing into the annulus about the casing, and thence back to the surface. Next, a cement slurry is mixed and pumped into the inside of the casing string, A plug, which acts as a piston within the casing, is placed above the cement slurry. This is to separate the top of the cement slurry from mud or water which is used to shove the cement down through the casing and out into the annulus. This plug further serves the purpose of shutting off against a baffle in the bottom end of the casing string, thus stopping the flow of cement out of the casing and leaving the shoe, or lower end of the casing, surrounded by cement and also filling the annulus there above. Casing strings cemented in the above described manner may vary in length from a few feet of large diameter pipe to very long lengths of smaller pipe. As of the present date the longest string of casing which has yet been cemented is some 16,600 ft deep. As a general rule, the deeper the well and the more cement slurry used, the higher the pressures which are required to place the slurry. In parts of West Texas, it is not uncommon to use 4000 sacks to cement a single string of casing in place. Machinery used to mix the cement and place it into the casing is mounted on heavy duty, powerfully equipped trucks which are capable of negotiating any type of highway or country roads. These trucks

Jan 1, 1949

By L. S. Darken

IT has long been recognized that the driving force in an isothermal diffusion process may be regarded as the negative gradient of the chemical potential (partial molal free energy) of the diffusing substance. This equivalence is exactly analogous to the fact that a mechanical force is the negative gradient of the potential energy. Nernst1 in 1888 expressed these driving forces in terms of osmotic pressure, which is directly related to the chemical potential and free energy. The relationship between the diffusivity, mobility and activity coefficient of electrolytes in aqueous solution has been developed in great detail by Onsager and Fuoss2 with results which have recently been confirmed experimentally by Harped and Nuttall.3 This interpretation of the driving force in isothermal diffusion has been discussed earlier by the author 4.6 who pointed out4 that "for a system of more than two components it is no longer necessarily true that a given element tends to diffuse toward a region of lower concentration even within a single phase region"; departure from the behavior of an ideal solution may be so great that the concentration gradient and the chemical potential gradient, or activity gradient, may be of different sign, thus giving rise to "up hill" diffusion. Since, in the discussion of that paper,4 some skepticism as to the validity of this conclusion was expressed, it seemed desirable to adduce experimental evidence to support it. Evidence of such diffusion in nonmetallic systems has already been reported. For example, it was observed by Hartley11 in a series of experiments in which sodium chloride diffused from a saturated solution in about 5 pct acetone in water into a solution virtually free of salt but with essentially the same acetone concentration. Specifically, a wine glass containing crystalline salt and saturated solution was totally immersed in a large glass cylinder containing the acetone-water solution without salt; the difference in specific gravity was such as to prevent convection. Diffusion of salt was accompanied by a marked depletion 0f acetone in the wine glass; after 3 days the acetone concentration decreased from 5.37 pct at the top of the glass, where the salt concentration was low (0.93 pct), to 1.84 pct at the bottom where the salt concentration was high (21.64 pct). This "uphill" diffusion was found to be such that the partial pressure (activity) of acetone was essentially equalized throughout the system when a steady state gradient of sodium chloride was maintained. In order to demonstrate the existence of such diffusion in metals, a series of four weld-diffusion experiments was made. In these measurements pairs of steel of virtually the same carbon content, but differing markedly in alloy content, were welded at the end and held at 1050°C for about two weeks. Subsequent analysis showed that carbon had diffused so as to produce an inequality

Jan 1, 1948

By M. R. Geer, H. F. Yancey

Coal washing assumed an important role in the mining industry of the Pacific Northwest long before washing practice became firmly established in the Appalachian field. A Scaife washer was operated in the state of Washington in 1887; and by 1927, the fist year for which complete statistics were compiled, nearly a third of the state's coal production was washed, in comparison with only about 5 pct for the country as a whole. Mechanical preparation was adopted in Alaska in 1922 in a plant constructed by the United States Navy at Chickaloon to provide bunker coal for naval forces operating in northern waters. Many of the coal beds mined in Washington and Alaska contained more impurities than those mined elsewhere, and this circumstance contributed to the early interest in mechanical cleaning. A much more important factor, however, was the inclination of the coal beds. With steeply pitching beds, hand sorting by the miner at the face is impossible; consequently, all material must be loaded and dealt with on the surface, just as is now proving the case with mechanical mining of flat beds. Thus "full-seam" mining afforded the same stimulus to the early development of coal washing in the Northwest that it is providing under mechanization in the rest of the country today. Objeet and Scope ' This report is intended to provide a general summary of the status of coal-washing practice in Washington, Oregon, and Alaska—an area in which some of the coals mined are more difficult to wash than those mined elsewhere in the country. Detailed flowsheets of plants, statistical data on production, and cost figures have been omitted, largely for the sake of brevity but also because such information is principally of only local interest. On the other hand, considerable washability data have been included because they are Washington At present Washington leads all other states in the percentage of its total production that is cleaned mechanically, 82.1 pct in comparison with the national average of 25.6 pct in 1945.' The washing problems encountered in this state are highly variable because the mountain-building forces that created the Cascade Range caused such intense folding and faulting of the beds in some fields that the rank of the coal was increased to anthracitic, while in other fields more distant from the mountains the beds were relatively undisturbed, and the rank of the coal ranges down through subbituminous to lignitic. The complicated and burdensome schedule of sizes prepared in most coal fields has never been required by the Washington market. With but few exceptions, lump is prepared on a round-hole screen of about 3 in. size, egg is about 3 to 1 5/8 or 1½ in., and nut is 1 5/8 or 1½ in. to either 1 or ¾ in. Some mines screen no finer than ¾ in. and market a slack coal of that top size, but generally the coal is screened at about ¼ in. to give a stoker coal of ¾ or 1 to ¼ in., and a ¼ in. to 0 "buckwheat." During recent years the market for lump coal has largely disappeared, and lump is crushed to supplement the pro-

Jan 1, 1950

By Paul L. Burkhart

THOUGH at an earlier period brief studies had been made by the Lehigh Navigation Coal Company Inc., it was not until 1924 that J. B. Warriner, then general manager, called for a comprehensive study of timber treatment, treating solutions, and related operations. Because of the impossibility of procuring accurate costs and other pertinent treating data, the American Wood Preserving Co. agreed to treat a car of mine timber at the Port Reading plant of the Reading Railroad. Fig. I shows the treating data collected at the treating plant on this timber, which was installed in two of the Lehigh mines in 1925. [ ] In the latter part of 1925, a survey of the tunnels and gangways of the company's Panther Valley mines was made to determine the proportion of gangways or tunnels timbered, cause of timber failures, approximate life of the average wood set and the approximate percentage of treated timber that it would be profitable for the company to use. Results of this survey appear in Table I. Because of the high percentage of timber that gave evidence of failure by rot, as noted in Table I, and a further study of the life of the sections where timbering was necessary, it was deemed advisable to fill 25 per cent of the yearly gangway timber requirement with treated timber. QUANTITIES AND TREATMENTS OF TREATED TIMBER PURCHASED In the early days of the program, none of the large treating companies would accept orders for small quantities of treated timber and the company was compelled to state the quantity of timber it would require at each operation in each month of the year. Table 2 is an example of the tabulation given to the various treating companies to assist them in making a yearly bid on the minimum quantity of timber required by the company during the year 1931. A bill of timber was calculated for each car, the weight of which would be between the minimum and maximum weight permitted for railroad-car loading. The treating company was paid for timber upon delivery at the operation specified. As extra cars of timber were required, they were ordered from the treating company, and payment was required on their receipt, on the basis of the piece or tonnage

Jan 1, 1942

AMONG the fellow prospectors of Black Jack Newman, locator of the claims that became the Miami mine, were J. D. Coplen and Bud Woodson. Woodson was in the district when the Bloody Tanks Indian massacre occurred, near the present town of Miami. He was a prospector long before Jack Newman worked in a mine, and for years he had done assessment work on some of the claims that Coplen acquired for his Inspiration company. Woodson recalls that a Scotch geologist from Morenci once visited his claims; and that the geologist tried to get the Phelps Dodge company interested in the property, but without success. Coplen interested some people in Kansas City in his claims that lay west of Newman's. He induced them to organize the Inspiration Mining Co., and by 1908 this company controlled 23 claims, which had been prospected in desultory fashion by a series of adits. One of these, near the Keystone property, encountered some lean copper-bearing rock, but later development failed to disclose any substantial quantity of ore at this particular point. Coplen, as general manager, in September, 1908, was negotiating with several exploration companies which at the time were on the lookout for low-grade copper properties. As a matter of fact, when J. Parke Channing visited Globe, in December, 1906, F. C. Alsdorf showed him the Inspiration claims as well as Newman's. Channing evinced little interest in an option on Inspiration because he could get so much better terms from Newman. He decided to concentrate his work on the Newman claims, with the idea that if he were successful in developing ore, he could later get Inspiration on terms at least equally good. Subsequently, the United States Smelting & Refining Co., which has since added "Mining" to its corporate name, took an option on Inspiration.

Jan 1, 1933

By Charles H. Thurman

THE data given herein were first included in a paper read before San Francisco Section, A.I.M.E., in October 1940, and are applicable to conditions existing until the gold-dredging industry was temporarily suspended by Order L-208 of the War Production Board in the fall of 1942. There is no doubt that gold dredging will be resumed at some future time, and on a scale equivalent to that of the recent past, but the cost data given herein will be affected to some extent by conditions existing at that time, and by labor rates and prices for materials then prevailing. DRAGLINE VS. BUCKET-LINE Dragline dredges should not be considered for mining large areas of low-grade placer gravel. In such deposits a dragline operator with a 5-cu. yd. dragline would be doing well to maintain an operating cost of 6¢ per cu. yd., while a bucket-line dredge with buckets no smaller than 7 cu. ft. each could be operated for less than 4¢ per cu. yd. By operating costs, I mean only field charges such as direct operating and overhead, which includes pay roll, power or fuel, repairs and maintenance, insurance, land clearing and general expenses, but not including such items as prospecting, depletion, depreciation of equipment, State Franchise Tax, or Federal Income Tax. It is not to be inferred that a dragline dredge cannot make a profit in small low-grade deposits, where the extent of a given property is too small to justify the use of the more costly bucket-line dredge. Consider small deposits of 10¢ gravel. It is obvious that a deposit of 5,000,000 cu. yd. of such gravel could not be mined profitably with a new, 7-cu. ft. bucket-line dredge, costing upward of $250,000, and with operation costs at 4¢ per cu. yd., paying for land or royalties out of earnings; nor could a new combination 5-cu. yd. dragline and washing plant, worth upward of $125,000 and working at 6¢ per cu. yd., make a profit. These comparisons are made because the hourly capacity of both types of dredges is nearly the same. The bucket-line dredge averages 93 per cent operating time in 24 hr., as against about 80 per cent or less for the dragline dredge. These percentages of operating time are important factors in making a comparison of this kind. The bucket-line dredge has greater efficiency in cleaning soft bedrock, usually characteristic of dredging deposits, and a 7-cu. ft. bucket-line dredge can be efficient to a total digging depth of 80 ft. (65 ft. below water, 15 ft. above). A 5-cu. yd. dragline dredge is limited to about 30 ft. of efficient digging depth, 5 ft. of which could be above water. In small areas of gravel not over 30 ft. deep, a 5-cu. yd. dragline dredge could make a profit where a bucket-line dredge could not do so. As an example: compare the dredging of 3,000,000 cu. yd. of 10¢ gravel 28 ft. deep with bucket line, costing 4¢ per cu. yd., and with a 5-cu. yd. dragline dredge operating at 6¢ per cu. yd. Because of small yardage, new equipment is not warranted, therefore we can assume that the dredges of both types are used equipment, fully depreciated. Dismantling, mov-

Jan 1, 1945

By d&apos, K. Mukherjee, C. R. Antonio, R. J. Maciag, G. J. Fischer

Tensile data indicate that over the range of strain rates 10-5 to 10-1 sec-1 and in the temperature range 298° to 743°K the flow stress at a given temperature may be expressed as: C0 = Cem where m changes abruptly at a critical strain rate of 10-2 sec-1. The Zener-Hollomon parameter was tested and found to be invalid except at temperatures exceeding 700° K. Values of AH calculated for temperatures above 700°K ranged from 30 to 47.5 kcal per g-mole. ThE flow characteristics of aluminum and aluminum alloys as a function of temperature and strain rate have been of interest to various experimenters for many years. Trozera et al.1 determined tensile flow curves for pure aluminum and concluded that the combined effect of temperature and strain rate on the flow stress could be related using the Zener-Hollomon parameter. More recently, Hockett2 proposed a relationship between compressive flow stress, temperature, and true strain rate which could be represented by a surface. Holt et al.3 studied strain rate effects on flow stress in a number of aluminum alloys at room temperature. It was determined that there is a critical strain rate above which a strain rate effect is observed. It was also reported that the strain rate sensitivity was significant in aluminum alloys in the "0" condition only. In a recent review paper McQueen4 has considered a number of mathematical expressions which have been used to describe the relationship between stress, strain rate, and temperature. These expressions have been applied to the flow characteristics of a number of different metals and alloys including aluminum. In the present work the strain rate sensitivity of 7075-0 aluminum was determined in the temperature range of 298° to 743°K. The tensile flow stress at 0.2 pct offset was obtained over a nominal strain rate range of 10-5 to 10-1 sec-1. EXPERIMENTAL Threaded tensile specimens were cut from a single heat of 7075-T6 aluminum. The composition of this heat is given in Table I. The test bars had a gage section 1.5 in. long by 0.250 in. diam and conformed to ASTM specification E-8-57T. After machining, the bars were annealed at 413° ± 10°C for 2 hr. They were then cooled to 260°C in 3 hr, and finally air cooled to room temperature. This treatment is commonly used to produce the "0" condition. Load-time curves at constant crosshead speeds were obtained at various temperatures using an Instron testing machine. Crosshead speeds ranged from 0.002 to 40 in. per min. A three-zone resistance tube furnace was used for the elevated-temperature tests. Temperatures were measured at three points along the gage length by means of suitably placed thermocouples. Each tensile bar was held at temperature for 30 min prior to testing and the maximum temperature variation along the gage length was kept below 1°C. In all, 275 samples were tested and each data point plotted is an average of at least two tests. In many cases the point represents up to six tests. RESULTS AND DISCUSSION Values of the flow stress at 0.2 pct offset at six different temperatures are plotted vs strain rate on log-log coordinates in Fig. 1. Over discrete ranges of strain rate, the data for each temperature fit the expression:

Jan 1, 1969

By E. W. McAllister

The decision of the California Oil Umpire's' office to accept well potentials established from subsurface-pressure data has brought to the attention of many operators for the first time the application of such data to production problems. This paper reviews the development and application of subsurface-pressure data in kettleman Hills, where these data have been used in production work since 1932. The Kettleman Hills field was discovered in October 1928. The first subsurface-pressure surveys were made early in 1932 and by the middle of 1933 the two major operators in the field were making routine pressure runs in thcir respective wells. Shortly therefter, these companies agreed to exchange pressure data, and later a third company entered into the agreement. This made it possible to analyze the effects upon the reservoir pressure of past production practices, which are discussed in the latter part of the report. It is interesting that many of the applications of subsurface-pressure data discussed herein were anticipated by C. L. Clark and C. B. Kimberlint in a report2 dated March 1933. PRODUCTIVITY Index In the majority of individual well problems involving the use of subsurface- pressure data, it is necessary to use a factor known as the "productivity index," which indicates the ability of a well to produce and represents the number of barrels of oil or oil and water per day that will enter the well bore for each pound per square inch pressure drop made opposite the producing interval of the well. The productivity index may be determined from pressure and production data for one or more rates of flow and a static or shut-in pressure survey or from production and pressure data for two or more rates of flow. Productivity indices may be based upon either net oil or total fluid production. All indices referred to in this report are based upon net oil. The value of the productivity index for Kettlcman Hills wells decreases generally with time and it is not uncommon for the index to vary in value at any specific time fur various rates of flow. The decline of the productivity index may be attributed partly to the loss of reservoir pressure. As the reservoir pressure decreases, gas originally in solution is released from the oil, congesting the flow of fluids through the formation and increasing the viscosity and surface tension of the oil; thus the flow resistance of the fluids through the formation is increased, resulting in a decrease of the productivity index. For convenient reference, the productivity indices for each well are plotted against time and a curve is drawn through the points showing the trend of the average index value. Plotted on Fig. I are index values for five

Jan 1, 1941

By W. C. Krumbein

GEOLOGICAL problems are approached from a geometrical (space relations) viewpoint, a kinematical (time sequence) viewpoint, or a dynamical viewpoint. The first two require sound training in conventional geology and in field methods. The third approach requires a solid foundation of chemistry, physics, and mathematics. Modern training for geologists should include close integration of basic sciences with geological principles. INTRODUCTION Our knowledge of the earth has increased tremendously during the last half century. We know more about its surface configuration, the distribution of its natural resources, the procession of living forms that inhabited it in the past, the chemical composition of its oceans, the areal distribution of its surface rocks, the movements of its atmosphere, and so on. Not only do we know more facts about the earth, but we have a better understanding of the processes that take place on and within it, such as the nature of earthquakes, the thermodynamics of the atmosphere, the chemical equilibria involved in the formation of igneous rocks, the mechanics of stream flow, the dynamics of the earth's origin, and so on. Many sciences contributed to the sum total of this knowledge, including such established disciplines as geology, geography, physics, chemistry, astronomy, biology. Out of this accumulation of new knowledge grew also a group of new sciences, such as seismology, oceanography, meteorology, volcanology, hydrology. Collectively these latter are known as the geophysical and geochemical sciences, and to a large extent they began as branches of geology. Until the turn of the century, for example, the study of earthquakes (seismology) was a part of geology, although as early as 1846 Mallet, a physicist, had suggested that the subject could be investigated by elastic-wave theory. Comparatively little progress was made along these lines until the seismograph was developed near the turn of the century; since then, additional earthquake data have accumulated rapidly, but more important, the interpretation of these data essentially has kept pace with their accumulation. In similar fashion, meteorology was generally considered a branch of geology as recently as one or two decades ago. Considerable progress had been made in such aspects as weather forecasting, but the science dates its recent rapid rise from the year 1911, when Bjerknes first applied the principles of dynamics to the analysis of air masses. The rapid development of such disciplines as oceanography, volcanology and hydrology was due in part to the application of principles of chemical equilibrium, of dynamics, and of thermodynamics to earth problems, by men who were essentially physicists or chemists by training. The last half century, therefore, and particularly the last two decades, saw the influx of numerous chemists and physicists into the realm of the earth sciences. In the meantime the main body of geology itself showed a marked growth, and

Jan 1, 1941

By R. C. Amero

FULLERS earth is a general name applied to claylike minerals that have high natural ad-sorptive powers. They are usually distinguished from ordinary clays by a higher content of combined moisture and a lower apparent density. The definition is based on the ancient use of the material for fulling, or cleansing woolen cloth of oil and grease; a more modern definition should mention the ability to decolorize oil and should differentiate between fullers earth, which is naturally active, and certain bentonites which only develop decolorizing power after being leached with strong mineral acids. The distinction between fullers earth and activable bentonite is not a sharp one, since all types of intermediate clays can be found that are more or less naturally active, yet more or less responsive to acid treatment. The differences seem to depend somewhat on the amount of leaching that has been effected by natural ground waters. Physical Properties The principal mineral constituent of activable bentonite is montmorillonite, a hydrous aluminum silicate to which the following formula is generally assigned: Al,Si,O,, (OH), • 12H,O Fullers earth, as well as bentonite, is usually composed of some variety of montmorillonite, but in the United States the largest tonnage of fullers earth is mined from deposits of attapulgite. Attapul- gite is a clay mineral composed of monoclinic crystals of colloidal size, having a fibrous shape similar to that of asbestos. A sectional model of the attapulgite "molecule" is shown in Fig. 1. A single unit is about 18.0 A wide and 12.9 A high. The length of the molecule is variable, but this same molecular pattern is repeated to form needlework crystals, rather than flakes, as is characteristic of the montmorillonite crystals. Attapulgite has been assigned the following formula,' although actually, the magnesia has been largely replaced by alumina: (0%) . (OH), • Mg, . Si, • Olp . 4H20. The fibrous nature of the mineral is clearly shown in the electron micrograph, Fig. 2. Although the deposits contain 5 to 30 pct quartz and carbonate minerals, impurities in the commercial products are held at a low level, principally by selective mining on the basis of oil decolorizing efficiency. The particle size distribution of this fullers earth has been estimated from settling rates, using sodium citrate as a dispersing agent.' Since Stokes' law only applies to spherical particles, the equivalent particle diameter calculated below is probably more nearly an index of diameter rather than length of the needlelike crystals: Eqnivalent Arbitrary Particle Distribution, Size Diameter Pci Classil3catian 0.05 mm 0.80 0.80 pct sand 0.05-0.02 mm 10.96 0.02-0.01 mm 9.65 42.10 pct silt 0.01-0.005 mm 11.40 0.005-0.002 mm 10.09 2-0.5 micron 10.61 0.5-0.2 micron 29.09 56.58 pct clay 0.2-0.05 micron 14.86 0.05 micron 1.96 The differential thermal analysis shown in Fig. 3 is unique and supports the theory that this is a distinct mineral species.' ~ Other general properties of the mineral as shown in Table I.

Jan 1, 1952

By J. Trevor Eyton

This paper addresses some of the financial risk hedging mechanisms available to a corporation contemplating entering the mining business at a significant level of investment. The approach which I have adopted is that of a case study relating to the risk hedging aspects of Brascan Limited's acquisition of 46% of Noranda Inc., formerly Noranda Mines Limited, followed by some remarks on options open to mining companies for reducing financial risks. To appreciate the rationale for Brascan committing over (Can.) $800 million to the natural resource sector, some knowledge of Brascan's parent company, Edper Investments Ltd., is required at the outset. Edper Investments, prior to acquiring a 48% interest in Brascan, controlled Trizec Corporation, one of the world's largest property companies. Edper also was involved in the financial services sector through Continental Bank of Canada and Hees International Corporation. For some considerable time prior to Edper's investment in Brascan, Edper felt a need to provide a better balance to its portfolio of property and financial services. Brascan was rich in cash, relatively unleveraged, and with important existing holdings in natural resources and consumer products. The acquisition of a controlling interest in Brascan provided an opportunity to balance Edper's portfolio of property and financial services with world class acquisitions in natural resources, supplemented by consumer products and financial services. The end result of Brascan's activities over the last few years is illustrated by the following analysis of the book value of Brascan's assets at the end of December 1983. [Can.$% Millions _ Natural Resources81748 Consumer Products 654 38 Financial Services 157 9 Other Operations895$1,717100% ] Source: Brascan 1983 Annual Report. The large emphasis on natural resources came about from the fact that for Canadians operating mainly in Canada, natural resources were attractive. We were impressed by Canada's position in the world natural resource industry as illustrated by some of the following statistics: [CommodityCanadian Estimated Production In 1983 As % of World Total Newsprint 30 Potash 21 Uranium 18 Molybdenum 17 Zinc 17 Pulp 16 Nickel 16 Saw Logs 11 Silver 8 Copper 7 Lead 6 Gas 5 Oil3] Source: U.S. Bureau of Mines and Brascan estimates. In addition, the quality of Canada's reserves looked good to us. The polymetallic nature of many of Canada's orebodies offered a hedge against risk relating to any one metal. Put another way, the by-product metal credits offered a net operating cost advantage with respect to many of the metals mined. Our energy costs also appeared to provide Canada's natural resource industries with an advantage. We considered Canadian mining expertise as amongst the world's finest, as were the exploration equipment and technology developed in Canada. In addition, Canada offered a stable political climate and one we knew. Further, we felt the Canadian Government's future role in the industry would, on balance, be benign, partly because the Canadian content of the mining industry was very high in contrast to the petroleum industry. Granted, we could find cheaper sources of copper; however, to do so would involve venturing into regions where country risks were higher.

Jan 1, 1985

GENERAL GEOLOGIC DESCRIPTION The mineral deposit of this case study can be described as a "typical" porphyry copper deposit of the southwestern USA and northern Mexico mineral province. The copper mineralization is related to Laramide age intrusives of intermediate composition which have been intruded into older, mostly crystalline, host rocks. Post Laramide deformation and faulting have subjected the deposit to erosion, leaching, and enrichment processes, which have created a secondarily enriched chalcocite zone. Later basin and range faulting down dropped the ore zone, resulting in deep burial beneath late Tertiary conglomerates and gravels, thus preserving the deposit from further erosion and oxidation. Lower grade chalcopyrite mineralization constitutes the primary zone underlying the enriched blanket. MANAGEMENT OF SAMPLE DATA Sample data were obtained from exploration diamond drill holes that were collared vertically and drilled with surface rigs. Most of the holes were surveyed downhole and found to deviate significantly from the vertical. The data were keypunched from original drill hole logs to formats as described in Chapter 6. Three types of cards were prepared: 1) A heading card containing the following information: [Project Name Coordi-in_ Hole Collarnates Bear-clina-Total ID Northing Easting Elevinglion Depth] 2) Individual record cards following each heading card with the following information: [SampleMin. Zone interval Assay Fields Leached (enriched ID From-ToTotal Cu Oxide Cu primary)] 3) Where downhole survey data were available, a card was punched for each downhole survey point. The card image looked very much like the heading card, followed immediately after the heading card, and contained the following information: [Hole Sur Point Sur Point Sur Point ID Bearing Inclination Depth] The keypunched data were then processed by the drill hole survey program producing a record file which contained information as follows: [Line 1. Project Name Date Assay Field Identifiers Line 2. Hole ID Northing Easting Elevation Bearing Inclination Number of Samples Line 3 through N+ 2 (where N equals the number of samples in the hole) Top Min. of Min. Zone Zone Sample Sample Coordinates Sample Assays Leach InterLength Northing Fasting Elev Total Cu Oxide Cu (etc) face] MINERAL BOUNDARY PROBLEM AND TREATMENT According to the geologic description, at least three mineral zones are present within the ore limits, as well as fault boundaries and a buried topographic surface, each of which have to be considered. The interfaces of the various mineralogical and geological boundaries were identified as accurately as possible in each drill hole by the project geologist, the location of the interface was surveyed in the computer program in association with the nearest sample intercept to the interface (note last field of line 3). Thus, the boundary is represented as a point in 3D space at each intersecting drill hole. The linear interpolation (LINTERP) program then searched the last field of the surveyed record to find the top of each mineral zone, or geologic boundary, and read the coordinates associated with that sample point. The program then used the coordinates to compute an interpolated surface between all existing data points as described in Chapter 11. A contour map was plotted for each of the computed surfaces and reviewed by the project geologist. Where the surfaces were poorly defined due to lack of real drill hole information, the geologist, at times, inserted a "pseudo" drill hole intercept according to his best judgment and feeling for the configuration of the surface, and such points were entered into the data stream for LINTERP. When the project geologists were satisfied that they had obtained

Jan 1, 1980